[U-Boot] [PATCH v2 2/2] ARM: ts4800: add ethernet support
Damien Riegel
damien.riegel at savoirfairelinux.com
Tue Jun 30 23:17:48 CEST 2015
This commit adds ethernet support to the TS4800. Note that the
MAC address is not fused on this board and have to be read from
FEC PALR PAUR registers (this is how the kernel provided by
Technologic Systems does it).
signed-off-by: Damien Riegel <damien.riegel at savoirfairelinux.com>
Cc: Stefano Babic <sbabic at denx.de>
---
Changes for v2:
- Reorder pads
arch/arm/include/asm/arch-mx5/iomux-mx51.h | 11 +++
board/technologic/ts4800/ts4800.c | 103 +++++++++++++++++++++++++++++
include/configs/ts4800.h | 16 +++++
3 files changed, 130 insertions(+)
diff --git a/arch/arm/include/asm/arch-mx5/iomux-mx51.h b/arch/arm/include/asm/arch-mx5/iomux-mx51.h
index 70aaa37..b7b1695 100644
--- a/arch/arm/include/asm/arch-mx5/iomux-mx51.h
+++ b/arch/arm/include/asm/arch-mx5/iomux-mx51.h
@@ -184,8 +184,19 @@ enum {
MX51_PAD_DISPB2_SER_DIO__GPIO3_6 = IOMUX_PAD(0x6c0, 0x2c0, 4, 0x98c, 1, MX51_GPIO_PAD_CTRL),
MX51_PAD_DI1_PIN3__DI1_PIN3 = IOMUX_PAD(0x72c, 0x32c, 0, __NA_, 0, NO_PAD_CTRL),
MX51_PAD_DI1_PIN2__DI1_PIN2 = IOMUX_PAD(0x734, 0x330, 0, __NA_, 0, NO_PAD_CTRL),
+ MX51_PAD_DI2_PIN2__FEC_MDC = IOMUX_PAD(0x74C, 0x344, 2, __NA_, 0, MX51_PAD_CTRL_5),
MX51_PAD_DI2_DISP_CLK__DI2_DISP_CLK = IOMUX_PAD(0x754, 0x34c, 0, __NA_, 0, NO_PAD_CTRL),
MX51_PAD_DI_GP4__DI2_PIN15 = IOMUX_PAD(0x758, 0x350, 4, __NA_, 0, NO_PAD_CTRL),
+ MX51_PAD_DISP2_DAT6__FEC_TDAT1 = IOMUX_PAD(0x774, 0x36C, 2, __NA_, 0, MX51_PAD_CTRL_5),
+ MX51_PAD_DISP2_DAT7__FEC_TDAT2 = IOMUX_PAD(0x778, 0x370, 2, __NA_, 0, MX51_PAD_CTRL_5),
+ MX51_PAD_DISP2_DAT8__FEC_TDAT3 = IOMUX_PAD(0x77C, 0x374, 2, __NA_, 0, MX51_PAD_CTRL_5),
+ MX51_PAD_DISP2_DAT9__FEC_TX_EN = IOMUX_PAD(0x780, 0x378, 2, __NA_, 0, MX51_PAD_CTRL_5),
+ MX51_PAD_DISP2_DAT10__FEC_COL = IOMUX_PAD(0x784, 0x37C, 2, 0x94c, 0x1, MX51_PAD_CTRL_2),
+ MX51_PAD_DISP2_DAT11__FEC_RXCLK = IOMUX_PAD(0x788, 0x380, 2, 0x968, 0x1, MX51_PAD_CTRL_2),
+ MX51_PAD_DISP2_DAT12__FEC_RX_DV = IOMUX_PAD(0x78C, 0x384, 2, 0x96c, 0x1, MX51_PAD_CTRL_4),
+ MX51_PAD_DISP2_DAT13__FEC_TX_CLK = IOMUX_PAD(0x790, 0x388, 2, 0x974, 0x1, MX51_PAD_CTRL_4),
+ MX51_PAD_DISP2_DAT14__FEC_RDAT0 = IOMUX_PAD(0x794, 0x38C, 2, 0x958, 0x1, MX51_PAD_CTRL_4),
+ MX51_PAD_DISP2_DAT15__FEC_TDAT0 = IOMUX_PAD(0x798, 0x390, 2, 0x0, 0, MX51_PAD_CTRL_5),
MX51_PAD_SD1_CMD__SD1_CMD = IOMUX_PAD(0x79c, 0x394, 0x10, __NA_, 0, MX51_SDHCI_PAD_CTRL),
MX51_PAD_SD1_CLK__SD1_CLK = IOMUX_PAD(0x7a0, 0x398, 0x10, __NA_, 0, MX51_SDHCI_PAD_CTRL | PAD_CTL_HYS),
MX51_PAD_SD1_DATA0__SD1_DATA0 = IOMUX_PAD(0x7a4, 0x39c, 0x10, __NA_, 0, MX51_SDHCI_PAD_CTRL),
diff --git a/board/technologic/ts4800/ts4800.c b/board/technologic/ts4800/ts4800.c
index 0a8d43e..6ef15e1 100644
--- a/board/technologic/ts4800/ts4800.c
+++ b/board/technologic/ts4800/ts4800.c
@@ -21,6 +21,9 @@
#include <fsl_esdhc.h>
#include <mc13892.h>
+#include <malloc.h>
+#include <netdev.h>
+#include <phy.h>
#include "ts4800.h"
DECLARE_GLOBAL_DATA_PTR;
@@ -62,6 +65,36 @@ static void setup_iomux_uart(void)
imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
}
+static void setup_iomux_fec(void)
+{
+ static const iomux_v3_cfg_t fec_pads[] = {
+ NEW_PAD_CTRL(MX51_PAD_EIM_EB2__FEC_MDIO,
+ PAD_CTL_HYS |
+ PAD_CTL_PUS_22K_UP |
+ PAD_CTL_DSE_HIGH | PAD_CTL_SRE_FAST),
+ MX51_PAD_EIM_EB3__FEC_RDATA1,
+ NEW_PAD_CTRL(MX51_PAD_EIM_CS2__FEC_RDATA2, PAD_CTL_HYS),
+ MX51_PAD_EIM_CS3__FEC_RDATA3,
+ MX51_PAD_NANDF_CS2__FEC_TX_ER,
+ MX51_PAD_EIM_CS5__FEC_CRS,
+ MX51_PAD_EIM_CS4__FEC_RX_ER,
+ /* PAD used on TS4800 */
+ MX51_PAD_DI2_PIN2__FEC_MDC,
+ MX51_PAD_DISP2_DAT14__FEC_RDAT0,
+ MX51_PAD_DISP2_DAT10__FEC_COL,
+ MX51_PAD_DISP2_DAT11__FEC_RXCLK,
+ MX51_PAD_DISP2_DAT15__FEC_TDAT0,
+ MX51_PAD_DISP2_DAT6__FEC_TDAT1,
+ MX51_PAD_DISP2_DAT7__FEC_TDAT2,
+ MX51_PAD_DISP2_DAT8__FEC_TDAT3,
+ MX51_PAD_DISP2_DAT9__FEC_TX_EN,
+ MX51_PAD_DISP2_DAT13__FEC_TX_CLK,
+ MX51_PAD_DISP2_DAT12__FEC_RX_DV,
+ };
+
+ imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
+}
+
#ifdef CONFIG_FSL_ESDHC
int board_mmc_getcd(struct mmc *mmc)
{
@@ -113,6 +146,7 @@ int board_mmc_init(bd_t *bis)
int board_early_init_f(void)
{
setup_iomux_uart();
+ setup_iomux_fec();
return 0;
}
@@ -126,6 +160,75 @@ int board_init(void)
}
/*
+ * Read the MAC address from FEC's registers PALR PAUR.
+ * User is supposed to configure these registers when MAC address is known
+ * from another source (fuse), but on TS4800, MAC address is not fused and
+ * the bootrom configure these registers on startup.
+ */
+static int fec_get_mac_from_register(uint32_t base_addr)
+{
+ unsigned char ethaddr[6];
+ u32 reg_mac[2];
+ int i;
+
+ reg_mac[0] = in_be32(base_addr + 0xE4);
+ reg_mac[1] = in_be32(base_addr + 0xE8);
+
+ for(i = 0; i < 6; i++)
+ ethaddr[i] = (reg_mac[i / 4] >> ((i % 4) * 8)) & 0xFF;
+
+ if (is_valid_ethaddr(ethaddr)) {
+ eth_setenv_enetaddr("ethaddr", ethaddr);
+ return 0;
+ }
+
+ return -1;
+}
+
+#define TS4800_GPIO_FEC_PHY_RES IMX_GPIO_NR(2, 14)
+int board_eth_init(bd_t *bd)
+{
+ int dev_id = -1;
+ int phy_id = 0xFF;
+ uint32_t addr = IMX_FEC_BASE;
+
+ uint32_t base_mii;
+ struct mii_dev *bus = NULL;
+ struct phy_device *phydev = NULL;
+ int ret;
+
+ /* reset FEC phy */
+ imx_iomux_v3_setup_pad(MX51_PAD_EIM_A20__GPIO2_14);
+ gpio_direction_output(TS4800_GPIO_FEC_PHY_RES, 0);
+ mdelay(1);
+ gpio_set_value(TS4800_GPIO_FEC_PHY_RES, 1);
+ mdelay(1);
+
+ base_mii = addr;
+ debug("eth_init: fec_probe(bd, %i, %i) @ %08x\n", dev_id, phy_id, addr);
+ bus = fec_get_miibus(base_mii, dev_id);
+ if (!bus)
+ return -ENOMEM;
+
+ phydev = phy_find_by_mask(bus, phy_id, PHY_INTERFACE_MODE_MII);
+ if (!phydev) {
+ free(bus);
+ return -ENOMEM;
+ }
+
+ if (fec_get_mac_from_register(addr))
+ printf("eth_init: failed to get MAC address\n");
+
+ ret = fec_probe(bd, dev_id, addr, bus, phydev);
+ if (ret) {
+ free(phydev);
+ free(bus);
+ }
+
+ return ret;
+}
+
+/*
* Do not overwrite the console
* Use always serial for U-Boot console
*/
diff --git a/include/configs/ts4800.h b/include/configs/ts4800.h
index d3722fa..21f1555 100644
--- a/include/configs/ts4800.h
+++ b/include/configs/ts4800.h
@@ -73,6 +73,22 @@
#define CONFIG_CMD_FAT
#define CONFIG_DOS_PARTITION
+/*
+ * Eth Configs
+ */
+#define CONFIG_MII
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_SMSC
+
+#define CONFIG_FEC_MXC
+#define IMX_FEC_BASE FEC_BASE_ADDR
+#define CONFIG_ETHPRIME "FEC"
+#define CONFIG_FEC_MXC_PHYADDR 0
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MII
+
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE /* disable vendor parameters protection (serial#, ethaddr) */
#define CONFIG_CONS_INDEX 1 /* use UART0 : used by serial driver */
--
2.1.4
More information about the U-Boot
mailing list