[U-Boot] [PATCH 15/28] net/memac_phy: reuse driver for little endian SoCs
Joe Hershberger
joe.hershberger at gmail.com
Fri Mar 20 04:33:54 CET 2015
On Thu, Mar 19, 2015 at 10:06 PM, Shaohui Xie <Shaohui.Xie at freescale.com>
wrote:
>
> Hello Joe,
>
>
>
> Thank you for reviewing this patch!
>
> Please see inline.
>
>
>
> Best Regards,
>
> Shaohui Xie
>
>
>
> From: Joe Hershberger [mailto:joe.hershberger at gmail.com]
> Sent: Friday, March 20, 2015 2:04 AM
> To: Sun York-R58495
> Cc: u-boot; Joe Hershberger; Xie Shaohui-B21989
> Subject: Re: [U-Boot] [PATCH 15/28] net/memac_phy: reuse driver for
little endian SoCs
>
>
>
> Hi Shaohui Xie,
>
> On Thu, Mar 19, 2015 at 11:45 AM, York Sun <yorksun at freescale.com> wrote:
> >
> > From: Shaohui Xie <Shaohui.Xie at freescale.com>
> >
> > The memac for PHY management on little endian SoCs is similar on big
> > endian SoCs, so we modify the driver by using I/O accessor function to
> > handle the endianness, so the driver can be reused on little endian
> > SoCs, we introduce CONFIG_SYS_MEMAC_LITTLE_ENDIAN for little endian
> > SoCs, if the CONFIG_SYS_MEMAC_LITTLE_ENDIAN is defined, the I/O access
> > is little endian, if not, the I/O access is big endian. Move fsl_memac.h
> > out of powerpc include.
> >
> > Signed-off-by: Shaohui Xie <Shaohui.Xie at freescale.com>
> > CC: Joe Hershberger <joe.hershberger at ni.com>
> > ---
> > arch/arm/include/asm/arch-fsl-lsch3/config.h | 1 +
> > drivers/net/Makefile | 1 +
> > drivers/net/fm/eth.c | 2 +-
> > drivers/net/fm/memac.c | 2 +-
> > drivers/net/fm/memac_phy.c | 62
++++++++++++++-------
> > drivers/net/vsc9953.c | 2 +-
> > {arch/powerpc/include/asm => include}/fsl_memac.h | 0
> > 7 files changed, 46 insertions(+), 24 deletions(-)
> > rename {arch/powerpc/include/asm => include}/fsl_memac.h (100%)
> >
> > diff --git a/arch/arm/include/asm/arch-fsl-lsch3/config.h
b/arch/arm/include/asm/arch-fsl-lsch3/config.h
> > index 98db1ef..684c70f 100644
> > --- a/arch/arm/include/asm/arch-fsl-lsch3/config.h
> > +++ b/arch/arm/include/asm/arch-fsl-lsch3/config.h
> > @@ -109,6 +109,7 @@
> >
> > /* IFC */
> > #define CONFIG_SYS_FSL_IFC_LE
> > +#define CONFIG_SYS_MEMAC_LITTLE_ENDIAN
>
> It seems tedious to have to define this. Can't you just use the functions
available?
>
> [S.H] To use a define is based on a concern that we cannot assume the I/O
access of an IP share same endianness as the Soc(s), we cannot assume on
little endian Soc the I/O access is little endian, on big endian Soc the
I/O access is big endian, the I/O access could be little endian on big
endian Soc and vice versa.
You're saying that the IP is expected to be in different endianness? If
that is practically the case, then I'm fine with this patch. I just want to
ensure that it is not just speculative generality.
> > /* PCIe */
> > #define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_IMMR +
0x2400000)
> > diff --git a/drivers/net/Makefile b/drivers/net/Makefile
> > index 5497934..d871093 100644
> > --- a/drivers/net/Makefile
> > +++ b/drivers/net/Makefile
> > @@ -66,4 +66,5 @@ obj-$(CONFIG_XILINX_LL_TEMAC) += xilinx_ll_temac.o
xilinx_ll_temac_mdio.o \
> > obj-$(CONFIG_ZYNQ_GEM) += zynq_gem.o
> > obj-$(CONFIG_FSL_MC_ENET) += fsl-mc/
> > obj-$(CONFIG_FSL_MC_ENET) += ldpaa_eth/
> > +obj-$(CONFIG_FSL_MEMAC) += fm/memac_phy.o
> > obj-$(CONFIG_VSC9953) += vsc9953.o
> > diff --git a/drivers/net/fm/eth.c b/drivers/net/fm/eth.c
> > index 1d1089d..a7a5c69 100644
> > --- a/drivers/net/fm/eth.c
> > +++ b/drivers/net/fm/eth.c
> > @@ -15,7 +15,7 @@
> > #include <phy.h>
> > #include <asm/fsl_dtsec.h>
> > #include <asm/fsl_tgec.h>
> > -#include <asm/fsl_memac.h>
> > +#include <fsl_memac.h>
> >
> > #include "fm.h"
> >
> > diff --git a/drivers/net/fm/memac.c b/drivers/net/fm/memac.c
> > index 60e898c..81a64bf 100644
> > --- a/drivers/net/fm/memac.c
> > +++ b/drivers/net/fm/memac.c
> > @@ -12,7 +12,7 @@
> > #include <phy.h>
> > #include <asm/types.h>
> > #include <asm/io.h>
> > -#include <asm/fsl_memac.h>
> > +#include <fsl_memac.h>
> >
> > #include "fm.h"
> >
> > diff --git a/drivers/net/fm/memac_phy.c b/drivers/net/fm/memac_phy.c
> > index a155d89..4ab78e6 100644
> > --- a/drivers/net/fm/memac_phy.c
> > +++ b/drivers/net/fm/memac_phy.c
> > @@ -10,9 +10,28 @@
> > #include <miiphy.h>
> > #include <phy.h>
> > #include <asm/io.h>
> > -#include <asm/fsl_memac.h>
> > +#include <fsl_memac.h>
> > #include <fm_eth.h>
> >
> > +#ifdef CONFIG_SYS_MEMAC_LITTLE_ENDIAN
>
> This can already be detected, right?
>
>
>
> #if __BYTE_ORDER == __LITTLE_ENDIAN
>
> [S.H] The issue is the IP’s I/O access order on LS2 is different from big
endian Soc(s).
>
> > +#define memac_out_32(a, v) out_le32(a, v)
> > +#define memac_clrbits_32(a, v) clrbits_le32(a, v)
> > +#define memac_setbits_32(a, v) setbits_le32(a, v)
> > +#else
> > +#define memac_out_32(a, v) out_be32(a, v)
> > +#define memac_clrbits_32(a, v) clrbits_be32(a, v)
> > +#define memac_setbits_32(a, v) setbits_be32(a, v)
> > +#endif
> > +
> > +static u32 memac_in_32(u32 *reg)
> > +{
> > +#ifdef CONFIG_SYS_MEMAC_LITTLE_ENDIAN
> > + return in_le32(reg);
> > +#else
> > + return in_be32(reg);
> > +#endif
> > +}
>
> Another option you have is to take the approach that you don't care the
endianness. Something like using the this type of pattern:
>
>
>
> value = ntohl(in_be32(reg));
>
> out_be32(reg, htonl(value));
>
> [S.H] same concern as above.
>
>
>
> > +
> > /*
> > * Write value to the PHY for this device to the register at regnum,
waiting
> > * until the write is done before it returns. All PHY configuration
has to be
> > @@ -28,31 +47,31 @@ int memac_mdio_write(struct mii_dev *bus, int
port_addr, int dev_addr,
> > if (dev_addr == MDIO_DEVAD_NONE) {
> > c45 = 0; /* clause 22 */
> > dev_addr = regnum & 0x1f;
> > - clrbits_be32(®s->mdio_stat, MDIO_STAT_ENC);
> > + memac_clrbits_32(®s->mdio_stat, MDIO_STAT_ENC);
> > } else
> > - setbits_be32(®s->mdio_stat, MDIO_STAT_ENC);
> > + memac_setbits_32(®s->mdio_stat, MDIO_STAT_ENC);
> >
> > /* Wait till the bus is free */
> > - while ((in_be32(®s->mdio_stat)) & MDIO_STAT_BSY)
> > + while ((memac_in_32(®s->mdio_stat)) & MDIO_STAT_BSY)
> > ;
> >
> > /* Set the port and dev addr */
> > mdio_ctl = MDIO_CTL_PORT_ADDR(port_addr) |
MDIO_CTL_DEV_ADDR(dev_addr);
> > - out_be32(®s->mdio_ctl, mdio_ctl);
> > + memac_out_32(®s->mdio_ctl, mdio_ctl);
> >
> > /* Set the register address */
> > if (c45)
> > - out_be32(®s->mdio_addr, regnum & 0xffff);
> > + memac_out_32(®s->mdio_addr, regnum & 0xffff);
> >
> > /* Wait till the bus is free */
> > - while ((in_be32(®s->mdio_stat)) & MDIO_STAT_BSY)
> > + while ((memac_in_32(®s->mdio_stat)) & MDIO_STAT_BSY)
> > ;
> >
> > /* Write the value to the register */
> > - out_be32(®s->mdio_data, MDIO_DATA(value));
> > + memac_out_32(®s->mdio_data, MDIO_DATA(value));
> >
> > /* Wait till the MDIO write is complete */
> > - while ((in_be32(®s->mdio_data)) & MDIO_DATA_BSY)
> > + while ((memac_in_32(®s->mdio_data)) & MDIO_DATA_BSY)
> > ;
> >
> > return 0;
> > @@ -75,39 +94,39 @@ int memac_mdio_read(struct mii_dev *bus, int
port_addr, int dev_addr,
> > return 0xffff;
> > c45 = 0; /* clause 22 */
> > dev_addr = regnum & 0x1f;
> > - clrbits_be32(®s->mdio_stat, MDIO_STAT_ENC);
> > + memac_clrbits_32(®s->mdio_stat, MDIO_STAT_ENC);
> > } else
> > - setbits_be32(®s->mdio_stat, MDIO_STAT_ENC);
> > + memac_setbits_32(®s->mdio_stat, MDIO_STAT_ENC);
> >
> > /* Wait till the bus is free */
> > - while ((in_be32(®s->mdio_stat)) & MDIO_STAT_BSY)
> > + while ((memac_in_32(®s->mdio_stat)) & MDIO_STAT_BSY)
> > ;
> >
> > /* Set the Port and Device Addrs */
> > mdio_ctl = MDIO_CTL_PORT_ADDR(port_addr) |
MDIO_CTL_DEV_ADDR(dev_addr);
> > - out_be32(®s->mdio_ctl, mdio_ctl);
> > + memac_out_32(®s->mdio_ctl, mdio_ctl);
> >
> > /* Set the register address */
> > if (c45)
> > - out_be32(®s->mdio_addr, regnum & 0xffff);
> > + memac_out_32(®s->mdio_addr, regnum & 0xffff);
> >
> > /* Wait till the bus is free */
> > - while ((in_be32(®s->mdio_stat)) & MDIO_STAT_BSY)
> > + while ((memac_in_32(®s->mdio_stat)) & MDIO_STAT_BSY)
> > ;
> >
> > /* Initiate the read */
> > mdio_ctl |= MDIO_CTL_READ;
> > - out_be32(®s->mdio_ctl, mdio_ctl);
> > + memac_out_32(®s->mdio_ctl, mdio_ctl);
> >
> > /* Wait till the MDIO write is complete */
> > - while ((in_be32(®s->mdio_data)) & MDIO_DATA_BSY)
> > + while ((memac_in_32(®s->mdio_data)) & MDIO_DATA_BSY)
> > ;
> >
> > /* Return all Fs if nothing was there */
> > - if (in_be32(®s->mdio_stat) & MDIO_STAT_RD_ER)
> > + if (memac_in_32(®s->mdio_stat) & MDIO_STAT_RD_ER)
> > return 0xffff;
> >
> > - return in_be32(®s->mdio_data) & 0xffff;
> > + return memac_in_32(®s->mdio_data) & 0xffff;
> > }
> >
> > int memac_mdio_reset(struct mii_dev *bus)
> > @@ -143,8 +162,9 @@ int fm_memac_mdio_init(bd_t *bis, struct
memac_mdio_info *info)
> > * like T2080QDS, this bit default is '0', which leads to MDIO
failure
> > * on XAUI PHY, so set this bit definitely.
> > */
> > - setbits_be32(&((struct memac_mdio_controller
*)info->regs)->mdio_stat,
> > - MDIO_STAT_CLKDIV(258) | MDIO_STAT_NEG);
> > + memac_setbits_32(
> > + &((struct memac_mdio_controller
*)info->regs)->mdio_stat,
> > + MDIO_STAT_CLKDIV(258) | MDIO_STAT_NEG);
> >
> > return mdio_register(bus);
> > }
> > diff --git a/drivers/net/vsc9953.c b/drivers/net/vsc9953.c
> > index 9fc3c18..fed7358 100644
> > --- a/drivers/net/vsc9953.c
> > +++ b/drivers/net/vsc9953.c
> > @@ -9,7 +9,7 @@
> > #include <asm/io.h>
> > #include <asm/fsl_serdes.h>
> > #include <fm_eth.h>
> > -#include <asm/fsl_memac.h>
> > +#include <fsl_memac.h>
> > #include <vsc9953.h>
> >
> > static struct vsc9953_info vsc9953_l2sw = {
> > diff --git a/arch/powerpc/include/asm/fsl_memac.h b/include/fsl_memac.h
> > similarity index 100%
> > rename from arch/powerpc/include/asm/fsl_memac.h
> > rename to include/fsl_memac.h
> > --
> > 1.7.9.5
> >
> > _______________________________________________
> > U-Boot mailing list
> > U-Boot at lists.denx.de
> > http://lists.denx.de/mailman/listinfo/u-boot
More information about the U-Boot
mailing list