[U-Boot] [PATCH v2] sunxi: Serial number support, obtained from SID bits and passed through ATAG

[Hans de Goede]

Hi,

On 22-03-15 12:31, Paul Kocialkowski wrote:
> Le dimanche 22 mars 2015 à 12:27 +0100, Hans de Goede a écrit :
>> Hi,
>>
>> On 22-03-15 11:42, Paul Kocialkowski wrote:
>>> Signed-off-by: Paul Kocialkowski <contact at paulk.fr>
>>
>> Thanks this version looks good, but I would like to have some more
>> certainty wrt how to deal with serial numbers in devicetree, where we
>> may e.g. store the full 128 bits of the sid, so I've send a mail
>> to the devicetree list about this with you in the Cc.
>
> In case it is possible to store the full 128 bits through device tree, I
> would still prefer to see only the 64 bits we selected being used, so
> that each device would show the same serial number in cpuinfo when using
> the legacy 3.4 kernel and a recent upstream kernel.

Right in /proc/cpuinfo we should always show the same, and we can
likely not extend the info to 128 bits there due to ABI compatibility concerns.

But we can e.g. show the entire 128 bit in /sys/firmware/devicetree/base/system-serial
in which case it makes sense to have the full 128 bit in the u-boot environment
and select word 0 and 3 in get_board_serial() at which point your patch needs
to change which is why I want to have a discussion about how to deal with
this in devicetree before merging the patch.

Regards,

Hans


>
>> Regards,
>>
>> Hans
>>
>>> ---
>>>    board/sunxi/board.c            | 51 +++++++++++++++++++++++++++++++++---------
>>>    include/configs/sunxi-common.h |  1 +
>>>    2 files changed, 41 insertions(+), 11 deletions(-)
>>>
>>> diff --git a/board/sunxi/board.c b/board/sunxi/board.c
>>> index e1891d1..d117558 100644
>>> --- a/board/sunxi/board.c
>>> +++ b/board/sunxi/board.c
>>> @@ -241,24 +241,53 @@ static struct musb_hdrc_platform_data musb_plat = {
>>>    };
>>>    #endif
>>>
>>> +#ifdef CONFIG_SERIAL_TAG
>>> +void get_board_serial(struct tag_serialnr *serialnr)
>>> +{
>>> +	char *serial_string = getenv("serial#");
>>> +	unsigned long long serial;
>>> +
>>> +	if (serial_string) {
>>> +		serial = simple_strtoull(serial_string, NULL, 16);
>>> +
>>> +		serialnr->high = (unsigned int) (serial >> 32);
>>> +		serialnr->low = (unsigned int) (serial & 0xffffffff);
>>> +	} else {
>>> +		serialnr->high = 0;
>>> +		serialnr->low = 0;
>>> +	}
>>> +}
>>> +#endif
>>> +
>>>    #ifdef CONFIG_MISC_INIT_R
>>>    int misc_init_r(void)
>>>    {
>>> +	char serial_string[17] = { 0 };
>>>    	unsigned int sid[4];
>>> +	uint8_t mac_addr[6];
>>> +	int ret;
>>> +
>>> +	ret = sunxi_get_sid(sid);
>>> +	if (ret == 0 && sid[0] != 0 && sid[3] != 0) {
>>> +		if (!getenv("ethaddr")) {
>>> +			/* Non OUI / registered MAC address */
>>> +			mac_addr[0] = 0x02;
>>> +			mac_addr[1] = (sid[0] >>  0) & 0xff;
>>> +			mac_addr[2] = (sid[3] >> 24) & 0xff;
>>> +			mac_addr[3] = (sid[3] >> 16) & 0xff;
>>> +			mac_addr[4] = (sid[3] >>  8) & 0xff;
>>> +			mac_addr[5] = (sid[3] >>  0) & 0xff;
>>> +
>>> +			eth_setenv_enetaddr("ethaddr", mac_addr);
>>> +		}
>>>
>>> -	if (!getenv("ethaddr") && sunxi_get_sid(sid) == 0 &&
>>> -			sid[0] != 0 && sid[3] != 0) {
>>> -		uint8_t mac_addr[6];
>>> +		if (!getenv("serial#")) {
>>> +			snprintf(serial_string, sizeof(serial_string),
>>> +				"%08x%08x", sid[0], sid[3]);
>>>
>>> -		mac_addr[0] = 0x02; /* Non OUI / registered MAC address */
>>> -		mac_addr[1] = (sid[0] >>  0) & 0xff;
>>> -		mac_addr[2] = (sid[3] >> 24) & 0xff;
>>> -		mac_addr[3] = (sid[3] >> 16) & 0xff;
>>> -		mac_addr[4] = (sid[3] >>  8) & 0xff;
>>> -		mac_addr[5] = (sid[3] >>  0) & 0xff;
>>> +			setenv("serial#", serial_string);
>>>
>>> -		eth_setenv_enetaddr("ethaddr", mac_addr);
>>> -	}
>>> +		}
>>>
>>>    #if defined(CONFIG_MUSB_HOST) || defined(CONFIG_MUSB_GADGET)
>>>    	musb_register(&musb_plat, NULL, (void *)SUNXI_USB0_BASE);
>>> diff --git a/include/configs/sunxi-common.h b/include/configs/sunxi-common.h
>>> index 1f7a1cb..b9bb971 100644
>>> --- a/include/configs/sunxi-common.h
>>> +++ b/include/configs/sunxi-common.h
>>> @@ -98,6 +98,7 @@
>>>    #define CONFIG_SETUP_MEMORY_TAGS
>>>    #define CONFIG_CMDLINE_TAG
>>>    #define CONFIG_INITRD_TAG
>>> +#define CONFIG_SERIAL_TAG
>>>
>>>    /* mmc config */
>>>    #if !defined(CONFIG_UART0_PORT_F)
>>>
>