[U-Boot] [PATCH v7 24/28] armv8/ls2085aqds: NAND boot support

[York Sun]

On 03/24/2015 12:30 PM, Scott Wood wrote:
> On Tue, 2015-03-24 at 12:25 -0700, York Sun wrote:
>> From: Scott Wood <scottwood at freescale.com>
>>
>> This adds NAND boot support for LS2085AQDS, using SPL framework.
>> Details of forming NAND image can be found in README.
>>
>> Signed-off-by: Scott Wood <scottwood at freescale.com>
>> Signed-off-by: York Sun <yorksun at freescale.com>
>>
>> ---
>>
>> Changes in v7:
>>   Move NAND boot instruction to fsl-lsch3/README.
>>   Update board setting to put RCW and u-boot in different NAND block.
>>
>> Changes in v6: None
>> Changes in v5:
>>   Update LS2085AQDS README to include instructions to form NAND image
>>
>> Changes in v4:
>>   Update MAINTAINERS file
>>
>> Changes in v3: None
>> Changes in v2: None
>>
>>  arch/arm/Kconfig                                  |    1 +
>>  arch/arm/cpu/armv8/fsl-lsch3/README               |   37 +++++++++++
>>  arch/arm/cpu/armv8/fsl-lsch3/soc.c                |   48 +++++++++++++
>>  arch/arm/cpu/armv8/{u-boot.lds => u-boot-spl.lds} |   74 +++++++++------------
>>  arch/arm/include/asm/arch-fsl-lsch3/config.h      |    9 +++
>>  arch/arm/lib/crt0_64.S                            |    7 ++
>>  board/freescale/ls2085aqds/MAINTAINERS            |    1 +
>>  board/freescale/ls2085aqds/ddr.c                  |    4 ++
>>  common/spl/spl.c                                  |    2 +-
>>  common/spl/spl_nand.c                             |    2 +-
>>  configs/ls2085aqds_nand_defconfig                 |    4 ++
>>  drivers/misc/fsl_ifc.c                            |   12 ++++
>>  drivers/mtd/nand/fsl_ifc_spl.c                    |    2 +-
>>  include/configs/ls2085a_common.h                  |   29 ++++++++
>>  include/configs/ls2085aqds.h                      |   50 ++++++++++++--
>>  15 files changed, 231 insertions(+), 51 deletions(-)
>>  copy arch/arm/cpu/armv8/{u-boot.lds => u-boot-spl.lds} (57%)
>>  create mode 100644 configs/ls2085aqds_nand_defconfig
>>
>> diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
>> index 6ba4b8d..f73541c 100644
>> --- a/arch/arm/Kconfig
>> +++ b/arch/arm/Kconfig
>> @@ -652,6 +652,7 @@ config TARGET_LS2085AQDS
>>  	bool "Support ls2085aqds"
>>  	select ARM64
>>  	select ARMV8_MULTIENTRY
>> +	select SUPPORT_SPL
>>  	help
>>  	  Support for Freescale LS2085AQDS platform
>>  	  The LS2085A Development System (QDS) is a high-performance
>> diff --git a/arch/arm/cpu/armv8/fsl-lsch3/README b/arch/arm/cpu/armv8/fsl-lsch3/README
>> index 4f36e2a..eee0228 100644
>> --- a/arch/arm/cpu/armv8/fsl-lsch3/README
>> +++ b/arch/arm/cpu/armv8/fsl-lsch3/README
>> @@ -95,3 +95,40 @@ mcboottimeout:	MC boot timeout in milliseconds. If this variable is not defined
>>  
>>  mcmemsize:	MC DRAM block size. If this variable is not defined, the value
>>  		CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE will be assumed.
>> +
>> +Booting from NAND
>> +-------------------
>> +Booting from NAND requires two images, RCW and u-boot-with-spl.bin.
>> +The difference between NAND boot RCW image and NOR boot image is the PBI
>> +command sequence. Below is one example for PBI commands.
>> +
>> +1) CCSR 4-byte write to 0x00e00404, data=0x00000000
>> +2) CCSR 4-byte write to 0x00e00400, data=0x1800a000
>> +The above two commands set bootloc register to 0x00000000_1800a000 where
>> +the u-boot code will be running in OCRAM.
>> +
>> +3) Block Copy: SRC=0x0119, SRC_ADDR=0x00080000, DEST_ADDR=0x1800a000,
>> +BLOCK_SIZE=0x00014000
>> +This command copies u-boot image from NAND device into OCRAM. The values need
>> +to adjust accordingly.
>> +
>> +SRC		should match the cfg_rcw_src, the reset config pins.
> 
> You should make it clear that this value depends on the type of NAND
> chip, and that the value for the QDS board is 0x107...

OK. I will 0x107 here and add 0x119 with RDB patch.

> 
>> +SRC_ADDR	is the offset of u-boot image in NAND device. It should match
>> +		CONFIG_SYS_NAND_U_BOOT_OFFS. In the example above, it is 512KB.
>> +DEST_ADDR	is fixed at 0x1800a000, matching bootloc set above.
>> +BLOCK_SIZE	is the size to be copied by PBI.
>> +
>> +RCW image should be written to the beginning of NAND device. Example of using
>> +u-boot command
>> +
>> +nand write <rcw image in memory> 0 <size of rcw image>
>> +
>> +To form the NAND image, build u-boot with NAND config, for example,
>> +ls2085aqds_nand_defconfig. The image needed is u-boot-with-spl.bin.
> 
> ...especially since this makes it look like the above example is for
> QDS.

Make sense.

York