[U-Boot] [PATCH v6 5/8] lpc32xx: add LPC32xx SSP support (SPI mode)
Jagan Teki
jagannadh.teki at gmail.com
Mon Mar 30 08:30:52 CEST 2015
On 18 March 2015 at 14:34, Albert ARIBAUD (3ADEV)
<albert.aribaud at 3adev.fr> wrote:
> Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud at 3adev.fr>
> ---
>
> Changes in v6: None
> Changes in v5: None
> Changes in v4: None
> Changes in v3:
> - move regs and functions in private struct
>
> Changes in v2:
> - added MUX setting for SSP0
>
> arch/arm/cpu/arm926ejs/lpc32xx/devices.c | 14 +++
> arch/arm/include/asm/arch-lpc32xx/clk.h | 3 +
> arch/arm/include/asm/arch-lpc32xx/sys_proto.h | 1 +
> drivers/spi/Makefile | 1 +
> drivers/spi/lpc32xx_ssp.c | 144 ++++++++++++++++++++++++++
> 5 files changed, 163 insertions(+)
> create mode 100644 drivers/spi/lpc32xx_ssp.c
>
> diff --git a/arch/arm/cpu/arm926ejs/lpc32xx/devices.c b/arch/arm/cpu/arm926ejs/lpc32xx/devices.c
> index a407098..5a453e3 100644
> --- a/arch/arm/cpu/arm926ejs/lpc32xx/devices.c
> +++ b/arch/arm/cpu/arm926ejs/lpc32xx/devices.c
> @@ -8,11 +8,13 @@
> #include <asm/arch/cpu.h>
> #include <asm/arch/clk.h>
> #include <asm/arch/uart.h>
> +#include <asm/arch/mux.h>
> #include <asm/io.h>
> #include <dm.h>
>
> static struct clk_pm_regs *clk = (struct clk_pm_regs *)CLK_PM_BASE;
> static struct uart_ctrl_regs *ctrl = (struct uart_ctrl_regs *)UART_CTRL_BASE;
> +static struct mux_regs *mux = (struct mux_regs *)MUX_BASE;
>
> void lpc32xx_uart_init(unsigned int uart_id)
> {
> @@ -66,3 +68,15 @@ void lpc32xx_i2c_init(unsigned int devnum)
> U_BOOT_DEVICE(lpc32xx_gpios) = {
> .name = "gpio_lpc32xx"
> };
> +
> +/* Mux for SCK0, MISO0, MOSI0. We do not use SSEL0. */
> +
> +#define P_MUX_SET_SSP0 0x1600
> +
> +void lpc32xx_ssp_init(void)
> +{
> + /* Enable SSP0 interface */
> + writel(CLK_SSP0_ENABLE_CLOCK, &clk->ssp_ctrl);
> + /* Mux SSP0 pins */
> + writel(P_MUX_SET_SSP0, &mux->p_mux_set);
> +}
> diff --git a/arch/arm/include/asm/arch-lpc32xx/clk.h b/arch/arm/include/asm/arch-lpc32xx/clk.h
> index 781ac07..2cb5703 100644
> --- a/arch/arm/include/asm/arch-lpc32xx/clk.h
> +++ b/arch/arm/include/asm/arch-lpc32xx/clk.h
> @@ -155,6 +155,9 @@ struct clk_pm_regs {
> #define CLK_NAND_MLC (1 << 1)
> #define CLK_NAND_MLC_INT (1 << 5)
>
> +/* SSP Clock Control Register bits */
> +#define CLK_SSP0_ENABLE_CLOCK (1 << 0)
> +
> unsigned int get_sys_clk_rate(void);
> unsigned int get_hclk_pll_rate(void);
> unsigned int get_hclk_clk_div(void);
> diff --git a/arch/arm/include/asm/arch-lpc32xx/sys_proto.h b/arch/arm/include/asm/arch-lpc32xx/sys_proto.h
> index a4a05d1..86d5ee9 100644
> --- a/arch/arm/include/asm/arch-lpc32xx/sys_proto.h
> +++ b/arch/arm/include/asm/arch-lpc32xx/sys_proto.h
> @@ -11,5 +11,6 @@ void lpc32xx_uart_init(unsigned int uart_id);
> void lpc32xx_mac_init(void);
> void lpc32xx_mlc_nand_init(void);
> void lpc32xx_i2c_init(unsigned int devnum);
> +void lpc32xx_ssp_init(void);
>
> #endif /* _LPC32XX_SYS_PROTO_H */
> diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
> index edbd520..ce6f1cc 100644
> --- a/drivers/spi/Makefile
> +++ b/drivers/spi/Makefile
> @@ -32,6 +32,7 @@ obj-$(CONFIG_EXYNOS_SPI) += exynos_spi.o
> obj-$(CONFIG_FTSSP010_SPI) += ftssp010_spi.o
> obj-$(CONFIG_ICH_SPI) += ich.o
> obj-$(CONFIG_KIRKWOOD_SPI) += kirkwood_spi.o
> +obj-$(CONFIG_LPC32XX_SSP) += lpc32xx_ssp.o
> obj-$(CONFIG_MPC52XX_SPI) += mpc52xx_spi.o
> obj-$(CONFIG_MPC8XXX_SPI) += mpc8xxx_spi.o
> obj-$(CONFIG_MXC_SPI) += mxc_spi.o
> diff --git a/drivers/spi/lpc32xx_ssp.c b/drivers/spi/lpc32xx_ssp.c
> new file mode 100644
> index 0000000..0fc44a0
> --- /dev/null
> +++ b/drivers/spi/lpc32xx_ssp.c
> @@ -0,0 +1,144 @@
> +/*
> + * LPC32xx SSP interface (SPI mode)
> + *
> + * (C) Copyright 2014 DENX Software Engineering GmbH
> + * Written-by: Albert ARIBAUD <albert.aribaud at 3adev.fr>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <linux/compat.h>
> +#include <asm/io.h>
> +#include <malloc.h>
> +#include <spi.h>
> +#include <asm/arch/clk.h>
> +
> +/* SSP chip registers */
> +struct ssp_regs {
> + u32 cr0;
> + u32 cr1;
> + u32 data;
> + u32 sr;
> + u32 cpsr;
> + u32 imsc;
> + u32 ris;
> + u32 mis;
> + u32 icr;
> + u32 dmacr;
> +};
> +
> +/* CR1 register defines */
> +#define SSP_CR1_SSP_ENABLE 0x0002
> +
> +/* SR register defines */
> +#define SSP_SR_TNF 0x0002
> +/* SSP status RX FIFO not empty bit */
> +#define SSP_SR_RNE 0x0004
> +
> +/* zynq spi slave */
Typo here.. zynq
> +struct lpc32xx_spi_slave {
> + struct spi_slave slave;
> + struct ssp_regs *regs;
> +};
> +
> +static inline struct lpc32xx_spi_slave *to_lpc32xx_spi_slave(
> + struct spi_slave *slave)
> +{
> + return container_of(slave, struct lpc32xx_spi_slave, slave);
> +}
> +
> +/* spi_init is called during boot when CONFIG_CMD_SPI is defined */
> +void spi_init(void)
> +{
> + /*
> + * nothing to do: clocking was enabled in lpc32xx_ssp_enable()
> + * and configuration will be done in spi_setup_slave()
> + */
> +}
> +
> +/* the following is called in sequence by do_spi_xfer() */
> +
> +struct spi_slave *spi_setup_slave(uint bus, uint cs, uint max_hz, uint mode)
> +{
> + struct lpc32xx_spi_slave *lslave;
> +
> + /* we only set up SSP0 for now, so ignore bus */
> +
> + if (mode & SPI_3WIRE) {
> + error("3-wire mode not supported");
> + return NULL;
> + }
> +
> + if (mode & SPI_SLAVE) {
> + error("slave mode not supported\n");
> + return NULL;
> + }
> +
> + if (mode & SPI_PREAMBLE) {
> + error("preamble byte skipping not supported\n");
> + return NULL;
> + }
> +
> + lslave = spi_alloc_slave(struct lpc32xx_spi_slave, bus, cs);
> + if (!lslave) {
> + printf("SPI_error: Fail to allocate lpc32xx_spi_slave\n");
> + return NULL;
> + }
> +
> + lslave->regs = (struct ssp_regs *)SSP0_BASE;
> +
> + /*
> + * 8 bit frame, SPI fmt, 500kbps -> clock divider is 26.
> + * Set SCR to 0 and CPSDVSR to 26.
> + */
> +
> + writel(0x7, &lslave->regs->cr0); /* 8-bit chunks, SPI, 1 clk/bit */
> + writel(26, &lslave->regs->cpsr); /* SSP clock = HCLK/26 = 500kbps */
> + writel(0, &lslave->regs->imsc); /* do not raise any interrupts */
> + writel(0, &lslave->regs->icr); /* clear any pending interrupt */
> + writel(0, &lslave->regs->dmacr); /* do not do DMAs */
> + writel(SSP_CR1_SSP_ENABLE, &lslave->regs->cr1); /* enable SSP0 */
> + return &lslave->slave;
> +}
> +
> +void spi_free_slave(struct spi_slave *slave)
> +{
> + struct lpc32xx_spi_slave *lslave = to_lpc32xx_spi_slave(slave);
> +
> + debug("(lpc32xx) spi_free_slave: 0x%08x\n", (u32)lslave);
> + free(lslave);
> +}
> +
> +int spi_claim_bus(struct spi_slave *slave)
> +{
> + /* only one bus and slave so far, always available */
> + return 0;
> +}
> +
> +int spi_xfer(struct spi_slave *slave, unsigned int bitlen,
> + const void *dout, void *din, unsigned long flags)
> +{
> + struct lpc32xx_spi_slave *lslave = to_lpc32xx_spi_slave(slave);
> + int bytelen = bitlen >> 3;
> + int idx_out = 0;
> + int idx_in = 0;
> + int start_time;
> +
> + start_time = get_timer(0);
> + while ((idx_out < bytelen) || (idx_in < bytelen)) {
> + int status = readl(&lslave->regs->sr);
> + if ((idx_out < bytelen) && (status & SSP_SR_TNF))
> + writel(((u8 *)dout)[idx_out++], &lslave->regs->data);
> + if ((idx_in < bytelen) && (status & status & SSP_SR_RNE))
> + ((u8 *)din)[idx_in++] = readl(&lslave->regs->data);
> + if (get_timer(start_time) >= CONFIG_LPC32XX_SSP_TIMEOUT)
> + return -1;
> + }
> + return 0;
> +}
> +
> +void spi_release_bus(struct spi_slave *slave)
> +{
> + /* do nothing */
> +}
> --
> 2.1.0
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki at gmail.com>
thanks!
--
Jagan.
More information about the U-Boot
mailing list