[U-Boot] [PATCH v4] dm: sf: Add Atmel DataFlash spi flash driver

Jagan Teki jteki at openedev.com
Thu May 14 12:50:09 CEST 2015


On 14 May 2015 at 14:57, Haikun Wang <haikun.wang at freescale.com> wrote:
> Atmel DataFlash chips have commands different from common spi
> flash commands.
> Atmel DataFlash also have special page-size.
> This driver add support for accessing Atmel DataFlash.
> It is based on the Driver Model.
> Example:
> => sf probe 1:0
> SPI DataFlash: Detected AT45DB021B with page size 264 Bytes, erase size 264 Bytes, total 264 KiB, revision d
> => sf erase 0 42000
> SF: 270336 bytes @ 0x0 Erased: OK
> => mw.l 82000000 45444342 20000
> => sf write 82000000 0 42000
> SF: 270336 bytes @ 0x0 Written: OK
> => sf read 83000000 0 42000
> SF: 270336 bytes @ 0x0 Read: OK
> => cmp.b 82000000 83000000 42000
> Total of 270336 byte(s) were the same
>
> Signed-off-by: Haikun Wang <haikun.wang at freescale.com>
> ---
> Verified with AT45DB021B on LS1021AQDS.
>
> Changes in v4:
> - Use dev_get_priv and dev_get_uclass_priv
> - Add test log to commit message
>
> Changes in v3:
> - 1. Rename file spi_dataflash.c to sf_dataflash.c
> - 2. Add comment for array "dataflash_data"
>
> Changes in v2:
> - 1. Correct comment style
> - 2. Use get_timer in dataflash_waitready to check whether timeout
> - 3. Remove struct spi_flash * in struct dataflash, and get it from udevice->uclass_priv
> - 4. Replace spi_flash_write_common with spi_flash_cmd_write
> - 5. Replace spi_flash_read with spi_flash_cmd_read
> - 6. Change type of varible "status" form char to u8 in dataflash_status
> - 7. Change add_dataflash's argument type due to <change 3>
> - 8. Add claim_bus and release_bus in erase/write/read due to <change 4 & 5>
>
> Changes in v1: None
>  drivers/mtd/spi/Makefile       |   1 +
>  drivers/mtd/spi/sf_dataflash.c | 711 +++++++++++++++++++++++++++++++++++++++++
>  2 files changed, 712 insertions(+)
>  create mode 100644 drivers/mtd/spi/sf_dataflash.c
>
> diff --git a/drivers/mtd/spi/Makefile b/drivers/mtd/spi/Makefile
> index c61b784..8adec3d 100644
> --- a/drivers/mtd/spi/Makefile
> +++ b/drivers/mtd/spi/Makefile
> @@ -15,6 +15,7 @@ endif
>  #ifndef CONFIG_DM_SPI
>  obj-$(CONFIG_SPI_FLASH) += sf_probe.o
>  #endif
> +obj-$(CONFIG_DM_SF_DATAFLASH) += sf_dataflash.o

This looks confuse to me,  CONFIG_SF_DATAFLASH looks simpler.

For long run all the driver stuff could move to DM, no need to specify
explicitly.

BTW:
Did you define this any board config?

>  obj-$(CONFIG_CMD_SF) += sf.o
>  obj-$(CONFIG_SPI_FLASH) += sf_ops.o sf_params.o
>  obj-$(CONFIG_SPI_FLASH_SANDBOX) += sandbox.o
> diff --git a/drivers/mtd/spi/sf_dataflash.c b/drivers/mtd/spi/sf_dataflash.c
> new file mode 100644
> index 0000000..d287db8
> --- /dev/null
> +++ b/drivers/mtd/spi/sf_dataflash.c
> @@ -0,0 +1,711 @@
> +/*
> + *
> + * Atmel DataFlash probing
> + *
> + * Copyright (C) 2004-2009, 2015 Freescale Semiconductor, Inc.
> + * Haikun Wang (haikun.wang at freescale.com)
> + *
> + * SPDX-License-Identifier:    GPL-2.0+
> +*/
> +#include <common.h>
> +#include <dm.h>
> +#include <errno.h>
> +#include <fdtdec.h>
> +#include <spi.h>
> +#include <spi_flash.h>
> +#include <div64.h>
> +#include <linux/err.h>
> +#include <linux/math64.h>
> +
> +#include "sf_internal.h"
> +
> +/*
> + * DataFlash is a kind of SPI flash.  Most AT45 chips have two buffers in
> + * each chip, which may be used for double buffered I/O; but this driver
> + * doesn't (yet) use these for any kind of i/o overlap or prefetching.
> + *
> + * Sometimes DataFlash is packaged in MMC-format cards, although the
> + * MMC stack can't (yet?) distinguish between MMC and DataFlash
> + * protocols during enumeration.
> + */
> +
> +/* reads can bypass the buffers */
> +#define OP_READ_CONTINUOUS     0xE8
> +#define OP_READ_PAGE           0xD2
> +
> +/* group B requests can run even while status reports "busy" */
> +#define OP_READ_STATUS         0xD7    /* group B */
> +
> +/* move data between host and buffer */
> +#define OP_READ_BUFFER1                0xD4    /* group B */
> +#define OP_READ_BUFFER2                0xD6    /* group B */
> +#define OP_WRITE_BUFFER1       0x84    /* group B */
> +#define OP_WRITE_BUFFER2       0x87    /* group B */
> +
> +/* erasing flash */
> +#define OP_ERASE_PAGE          0x81
> +#define OP_ERASE_BLOCK         0x50
> +
> +/* move data between buffer and flash */
> +#define OP_TRANSFER_BUF1       0x53
> +#define OP_TRANSFER_BUF2       0x55
> +#define OP_MREAD_BUFFER1       0xD4
> +#define OP_MREAD_BUFFER2       0xD6
> +#define OP_MWERASE_BUFFER1     0x83
> +#define OP_MWERASE_BUFFER2     0x86
> +#define OP_MWRITE_BUFFER1      0x88    /* sector must be pre-erased */
> +#define OP_MWRITE_BUFFER2      0x89    /* sector must be pre-erased */
> +
> +/* write to buffer, then write-erase to flash */
> +#define OP_PROGRAM_VIA_BUF1    0x82
> +#define OP_PROGRAM_VIA_BUF2    0x85
> +
> +/* compare buffer to flash */
> +#define OP_COMPARE_BUF1                0x60
> +#define OP_COMPARE_BUF2                0x61
> +
> +/* read flash to buffer, then write-erase to flash */
> +#define OP_REWRITE_VIA_BUF1    0x58
> +#define OP_REWRITE_VIA_BUF2    0x59
> +
> +/*
> + * newer chips report JEDEC manufacturer and device IDs; chip
> + * serial number and OTP bits; and per-sector writeprotect.
> + */
> +#define OP_READ_ID             0x9F
> +#define OP_READ_SECURITY       0x77
> +#define OP_WRITE_SECURITY_REVC 0x9A
> +#define OP_WRITE_SECURITY      0x9B    /* revision D */
> +
> +
> +struct dataflash {
> +       uint8_t                 command[16];
> +       unsigned short          page_offset;    /* offset in flash address */
> +};
> +
> +/*
> + * Return the status of the DataFlash device.
> + */
> +static inline int dataflash_status(struct spi_slave *spi)
> +{
> +       int ret;
> +       u8 status;
> +       /*
> +        * NOTE:  at45db321c over 25 MHz wants to write
> +        * a dummy byte after the opcode...
> +        */
> +       ret = spi_flash_cmd(spi, OP_READ_STATUS, &status, 1);
> +       return ret ? -EIO : status;
> +}
> +
> +/*
> + * Poll the DataFlash device until it is READY.
> + * This usually takes 5-20 msec or so; more for sector erase.
> + * ready: return > 0
> + */
> +static int dataflash_waitready(struct spi_slave *spi)
> +{
> +       int status;
> +       int timeout = 2 * CONFIG_SYS_HZ;
> +       int timebase;
> +
> +       timebase = get_timer(0);
> +       do {
> +               status = dataflash_status(spi);
> +               if (status < 0)
> +                       status = 0;
> +
> +               if (status & (1 << 7))  /* RDY/nBSY */
> +                       return status;
> +
> +               mdelay(3);
> +       } while (get_timer(timebase) < timeout);
> +
> +       return -ETIME;
> +}
> +
> +/*
> + * Erase pages of flash.
> + */
> +static int spi_dataflash_erase(struct udevice *dev, u32 offset, size_t len)
> +{
> +       struct dataflash        *dataflash;
> +       struct spi_flash        *spi_flash;
> +       struct spi_slave        *spi;
> +       unsigned                blocksize;
> +       uint8_t                 *command;
> +       uint32_t                rem;
> +       int                     status;
> +
> +       dataflash = dev_get_priv(dev);
> +       spi_flash = dev_get_uclass_priv(dev);
> +       spi = spi_flash->spi;
> +
> +       blocksize = spi_flash->page_size << 3;
> +
> +       memset(dataflash->command, 0 , sizeof(dataflash->command));
> +       command = dataflash->command;
> +
> +       debug("%s: erase addr=0x%x len 0x%x\n", dev->name, offset, len);
> +
> +       div_u64_rem(len, spi_flash->page_size, &rem);
> +       if (rem)
> +               return -EINVAL;
> +       div_u64_rem(offset, spi_flash->page_size, &rem);
> +       if (rem)
> +               return -EINVAL;
> +
> +       status = spi_claim_bus(spi);
> +       if (status) {
> +               debug("SPI DATAFLASH: unable to claim SPI bus\n");
> +               return status;
> +       }
> +
> +       while (len > 0) {
> +               unsigned int    pageaddr;
> +               int             do_block;
> +               /*
> +                * Calculate flash page address; use block erase (for speed) if
> +                * we're at a block boundary and need to erase the whole block.
> +                */
> +               pageaddr = div_u64(offset, spi_flash->page_size);
> +               do_block = (pageaddr & 0x7) == 0 && len >= blocksize;
> +               pageaddr = pageaddr << dataflash->page_offset;
> +
> +               command[0] = do_block ? OP_ERASE_BLOCK : OP_ERASE_PAGE;
> +               command[1] = (uint8_t)(pageaddr >> 16);
> +               command[2] = (uint8_t)(pageaddr >> 8);
> +               command[3] = 0;
> +
> +               debug("%s ERASE %s: (%x) %x %x %x [%d]\n",
> +                     dev->name, do_block ? "block" : "page",
> +                     command[0], command[1], command[2], command[3],
> +                     pageaddr);
> +
> +               status = spi_flash_cmd_write(spi, command, 4, NULL, 0);
> +               if (status < 0) {
> +                       debug("%s: erase send command error!\n", dev->name);
> +                       return -EIO;
> +               }
> +
> +               status = dataflash_waitready(spi);
> +               if (status < 0) {
> +                       debug("%s: erase waitready error!\n", dev->name);
> +                       return status;
> +               }
> +
> +               if (do_block) {
> +                       offset += blocksize;
> +                       len -= blocksize;
> +               } else {
> +                       offset += spi_flash->page_size;
> +                       len -= spi_flash->page_size;
> +               }
> +       }
> +
> +       spi_release_bus(spi);
> +
> +       return 0;
> +}
> +
> +/*
> + * Read from the DataFlash device.
> + *   offset : Start offset in flash device
> + *   len    : Amount to read
> + *   buf    : Buffer containing the data
> + */
> +static int spi_dataflash_read(struct udevice *dev, u32 offset, size_t len,
> +                             void *buf)
> +{
> +       struct dataflash        *dataflash;
> +       struct spi_flash        *spi_flash;
> +       struct spi_slave        *spi;
> +       unsigned int            addr;
> +       uint8_t                 *command;
> +       int                     status;
> +
> +       dataflash = dev_get_priv(dev);
> +       spi_flash = dev_get_uclass_priv(dev);
> +       spi = spi_flash->spi;
> +
> +       memset(dataflash->command, 0 , sizeof(dataflash->command));
> +       command = dataflash->command;
> +
> +       debug("%s: erase addr=0x%x len 0x%x\n", dev->name, offset, len);
> +       debug("READ: (%x) %x %x %x\n",
> +             command[0], command[1], command[2], command[3]);
> +
> +       /* Calculate flash page/byte address */
> +       addr = (((unsigned)offset / spi_flash->page_size)
> +              << dataflash->page_offset)
> +              + ((unsigned)offset % spi_flash->page_size);
> +
> +       status = spi_claim_bus(spi);
> +       if (status) {
> +               debug("SPI DATAFLASH: unable to claim SPI bus\n");
> +               return status;
> +       }
> +
> +       /*
> +        * Continuous read, max clock = f(car) which may be less than
> +        * the peak rate available.  Some chips support commands with
> +        * fewer "don't care" bytes.  Both buffers stay unchanged.
> +        */
> +       command[0] = OP_READ_CONTINUOUS;
> +       command[1] = (uint8_t)(addr >> 16);
> +       command[2] = (uint8_t)(addr >> 8);
> +       command[3] = (uint8_t)(addr >> 0);
> +
> +       /* plus 4 "don't care" bytes, command len: 4 + 4 "don't care" bytes */
> +       status = spi_flash_cmd_read(spi, command, 8, buf, len);
> +
> +       spi_release_bus(spi);
> +
> +       return status;
> +}
> +
> +/*
> + * Write to the DataFlash device.
> + *   offset     : Start offset in flash device
> + *   len    : Amount to write
> + *   buf    : Buffer containing the data
> + */
> +int spi_dataflash_write(struct udevice *dev, u32 offset, size_t len,
> +                       const void *buf)
> +{
> +       struct dataflash        *dataflash;
> +       struct spi_flash        *spi_flash;
> +       struct spi_slave        *spi;
> +       uint8_t                 *command;
> +       unsigned int            pageaddr, addr, to, writelen;
> +       size_t                  remaining = len;
> +       u_char                  *writebuf = (u_char *)buf;
> +       int                     status = -EINVAL;
> +
> +       dataflash = dev_get_priv(dev);
> +       spi_flash = dev_get_uclass_priv(dev);
> +       spi = spi_flash->spi;
> +
> +       memset(dataflash->command, 0 , sizeof(dataflash->command));
> +       command = dataflash->command;
> +
> +       debug("%s: write 0x%x..0x%x\n", dev->name, offset, (offset + len));
> +
> +       pageaddr = ((unsigned)offset / spi_flash->page_size);
> +       to = ((unsigned)offset % spi_flash->page_size);
> +       if (to + len > spi_flash->page_size)
> +               writelen = spi_flash->page_size - to;
> +       else
> +               writelen = len;
> +
> +       status = spi_claim_bus(spi);
> +       if (status) {
> +               debug("SPI DATAFLASH: unable to claim SPI bus\n");
> +               return status;
> +       }
> +
> +       while (remaining > 0) {
> +               debug("write @ %d:%d len=%d\n", pageaddr, to, writelen);
> +
> +               /*
> +                * REVISIT:
> +                * (a) each page in a sector must be rewritten at least
> +                *     once every 10K sibling erase/program operations.
> +                * (b) for pages that are already erased, we could
> +                *     use WRITE+MWRITE not PROGRAM for ~30% speedup.
> +                * (c) WRITE to buffer could be done while waiting for
> +                *     a previous MWRITE/MWERASE to complete ...
> +                * (d) error handling here seems to be mostly missing.
> +                *
> +                * Two persistent bits per page, plus a per-sector counter,
> +                * could support (a) and (b) ... we might consider using
> +                * the second half of sector zero, which is just one block,
> +                * to track that state.  (On AT91, that sector should also
> +                * support boot-from-DataFlash.)
> +                */
> +
> +               addr = pageaddr << dataflash->page_offset;
> +
> +               /* (1) Maybe transfer partial page to Buffer1 */
> +               if (writelen != spi_flash->page_size) {
> +                       command[0] = OP_TRANSFER_BUF1;
> +                       command[1] = (addr & 0x00FF0000) >> 16;
> +                       command[2] = (addr & 0x0000FF00) >> 8;
> +                       command[3] = 0;
> +
> +                       debug("TRANSFER: (%x) %x %x %x\n",
> +                             command[0], command[1], command[2], command[3]);
> +
> +                       status = spi_flash_cmd_write(spi, command, 4, NULL, 0);
> +                       if (status < 0) {
> +                               debug("%s: write(<pagesize) command error!\n",
> +                                     dev->name);
> +                               return -EIO;
> +                       }
> +
> +                       status = dataflash_waitready(spi);
> +                       if (status < 0) {
> +                               debug("%s: write(<pagesize) waitready error!\n",
> +                                     dev->name);
> +                               return status;
> +                       }
> +               }
> +
> +               /* (2) Program full page via Buffer1 */
> +               addr += to;
> +               command[0] = OP_PROGRAM_VIA_BUF1;
> +               command[1] = (addr & 0x00FF0000) >> 16;
> +               command[2] = (addr & 0x0000FF00) >> 8;
> +               command[3] = (addr & 0x000000FF);
> +
> +               debug("PROGRAM: (%x) %x %x %x\n",
> +                     command[0], command[1], command[2], command[3]);
> +
> +               status = spi_flash_cmd_write(spi, command,
> +                                            4, writebuf, writelen);
> +               if (status < 0) {
> +                       debug("%s: write send command error!\n", dev->name);
> +                       return -EIO;
> +               }
> +
> +               status = dataflash_waitready(spi);
> +               if (status < 0) {
> +                       debug("%s: write waitready error!\n", dev->name);
> +                       return status;
> +               }
> +
> +#ifdef CONFIG_SPI_DATAFLASH_WRITE_VERIFY
> +               /* (3) Compare to Buffer1 */
> +               addr = pageaddr << dataflash->page_offset;
> +               command[0] = OP_COMPARE_BUF1;
> +               command[1] = (addr & 0x00FF0000) >> 16;
> +               command[2] = (addr & 0x0000FF00) >> 8;
> +               command[3] = 0;
> +
> +               debug("COMPARE: (%x) %x %x %x\n",
> +                     command[0], command[1], command[2], command[3]);
> +
> +               status = spi_flash_cmd_write(spi, command,
> +                                            4, writebuf, writelen);
> +               if (status < 0) {
> +                       debug("%s: write(compare) send command error!\n",
> +                             dev->name);
> +                       return -EIO;
> +               }
> +
> +               status = dataflash_waitready(spi);
> +
> +               /* Check result of the compare operation */
> +               if (status & (1 << 6)) {
> +                       printf("SPI DataFlash: write compare page %u, err %d\n",
> +                              pageaddr, status);
> +                       remaining = 0;
> +                       status = -EIO;
> +                       break;
> +               } else {
> +                       status = 0;
> +               }
> +
> +#endif /* CONFIG_SPI_DATAFLASH_WRITE_VERIFY */
> +               remaining = remaining - writelen;
> +               pageaddr++;
> +               to = 0;
> +               writebuf += writelen;
> +
> +               if (remaining > spi_flash->page_size)
> +                       writelen = spi_flash->page_size;
> +               else
> +                       writelen = remaining;
> +       }
> +
> +       spi_release_bus(spi);
> +
> +       return 0;
> +}
> +
> +static int add_dataflash(struct udevice *dev, char *name, int nr_pages,
> +                            int pagesize, int pageoffset, char revision)
> +{
> +       struct spi_flash *spi_flash;
> +       struct dataflash *dataflash;
> +
> +       dataflash = dev_get_priv(dev);
> +       spi_flash = dev_get_uclass_priv(dev);
> +
> +       dataflash->page_offset = pageoffset;
> +
> +       spi_flash->name = name;
> +       spi_flash->page_size = pagesize;
> +       spi_flash->size = nr_pages * pagesize;
> +       spi_flash->erase_size = pagesize;
> +
> +#ifndef CONFIG_SPL_BUILD
> +       printf("SPI DataFlash: Detected %s with page size ", spi_flash->name);
> +       print_size(spi_flash->page_size, ", erase size ");
> +       print_size(spi_flash->erase_size, ", total ");
> +       print_size(spi_flash->size, "");
> +       printf(", revision %c", revision);
> +       puts("\n");
> +#endif
> +
> +       return 0;
> +}
> +
> +struct flash_info {
> +       char            *name;
> +
> +       /*
> +        * JEDEC id has a high byte of zero plus three data bytes:
> +        * the manufacturer id, then a two byte device id.
> +        */
> +       uint32_t        jedec_id;
> +
> +       /* The size listed here is what works with OP_ERASE_PAGE. */
> +       unsigned        nr_pages;
> +       uint16_t        pagesize;
> +       uint16_t        pageoffset;
> +
> +       uint16_t        flags;
> +#define SUP_POW2PS     0x0002          /* supports 2^N byte pages */
> +#define IS_POW2PS      0x0001          /* uses 2^N byte pages */
> +};
> +
> +static struct flash_info dataflash_data[] = {
> +       /*
> +        * NOTE:  chips with SUP_POW2PS (rev D and up) need two entries,
> +        * one with IS_POW2PS and the other without.  The entry with the
> +        * non-2^N byte page size can't name exact chip revisions without
> +        * losing backwards compatibility for cmdlinepart.
> +        *
> +        * Those two entries have different name spelling format in order to
> +        * show their difference obviously.
> +        * The upper case refer to the chip isn't in normal 2^N bytes page-size
> +        * mode.
> +        * The lower case refer to the chip is in normal 2^N bytes page-size
> +        * mode.
> +        *
> +        * These newer chips also support 128-byte security registers (with
> +        * 64 bytes one-time-programmable) and software write-protection.
> +        */
> +       { "AT45DB011B",  0x1f2200, 512, 264, 9, SUP_POW2PS},
> +       { "at45db011d",  0x1f2200, 512, 256, 8, SUP_POW2PS | IS_POW2PS},
> +
> +       { "AT45DB021B",  0x1f2300, 1024, 264, 9, SUP_POW2PS},
> +       { "at45db021d",  0x1f2300, 1024, 256, 8, SUP_POW2PS | IS_POW2PS},
> +
> +       { "AT45DB041x",  0x1f2400, 2048, 264, 9, SUP_POW2PS},
> +       { "at45db041d",  0x1f2400, 2048, 256, 8, SUP_POW2PS | IS_POW2PS},
> +
> +       { "AT45DB081B",  0x1f2500, 4096, 264, 9, SUP_POW2PS},
> +       { "at45db081d",  0x1f2500, 4096, 256, 8, SUP_POW2PS | IS_POW2PS},
> +
> +       { "AT45DB161x",  0x1f2600, 4096, 528, 10, SUP_POW2PS},
> +       { "at45db161d",  0x1f2600, 4096, 512, 9, SUP_POW2PS | IS_POW2PS},
> +
> +       { "AT45DB321x",  0x1f2700, 8192, 528, 10, 0},           /* rev C */
> +
> +       { "AT45DB321x",  0x1f2701, 8192, 528, 10, SUP_POW2PS},
> +       { "at45db321d",  0x1f2701, 8192, 512, 9, SUP_POW2PS | IS_POW2PS},
> +
> +       { "AT45DB642x",  0x1f2800, 8192, 1056, 11, SUP_POW2PS},
> +       { "at45db642d",  0x1f2800, 8192, 1024, 10, SUP_POW2PS | IS_POW2PS},
> +};
> +
> +static struct flash_info *jedec_probe(struct spi_slave *spi, u8 *id)
> +{
> +       int                     tmp;
> +       uint32_t                jedec;
> +       struct flash_info       *info;
> +       int status;
> +
> +       /*
> +        * JEDEC also defines an optional "extended device information"
> +        * string for after vendor-specific data, after the three bytes
> +        * we use here.  Supporting some chips might require using it.
> +        *
> +        * If the vendor ID isn't Atmel's (0x1f), assume this call failed.
> +        * That's not an error; only rev C and newer chips handle it, and
> +        * only Atmel sells these chips.
> +        */
> +       if (id[0] != 0x1f)
> +               return NULL;
> +
> +       jedec = id[0];
> +       jedec = jedec << 8;
> +       jedec |= id[1];
> +       jedec = jedec << 8;
> +       jedec |= id[2];
> +
> +       for (tmp = 0, info = dataflash_data;
> +                       tmp < ARRAY_SIZE(dataflash_data);
> +                       tmp++, info++) {
> +               if (info->jedec_id == jedec) {
> +                       if (info->flags & SUP_POW2PS) {
> +                               status = dataflash_status(spi);
> +                               if (status < 0) {
> +                                       debug("SPI DataFlash: status error %d\n",
> +                                             status);
> +                                       return NULL;
> +                               }
> +                               if (status & 0x1) {
> +                                       if (info->flags & IS_POW2PS)
> +                                               return info;
> +                               } else {
> +                                       if (!(info->flags & IS_POW2PS))
> +                                               return info;
> +                               }
> +                       } else {
> +                               return info;
> +                       }
> +               }
> +       }
> +
> +       /*
> +        * Treat other chips as errors ... we won't know the right page
> +        * size (it might be binary) even when we can tell which density
> +        * class is involved (legacy chip id scheme).
> +        */
> +       printf("SPI DataFlash: Unsupported flash IDs: ");
> +       printf("manuf %02x, jedec %04x, ext_jedec %04x\n",
> +              id[0], jedec, id[3] << 8 | id[4]);
> +       return NULL;
> +}
> +
> +/*
> + * Detect and initialize DataFlash device, using JEDEC IDs on newer chips
> + * or else the ID code embedded in the status bits:
> + *
> + *   Device      Density         ID code          #Pages PageSize  Offset
> + *   AT45DB011B  1Mbit   (128K)  xx0011xx (0x0c)    512    264      9
> + *   AT45DB021B  2Mbit   (256K)  xx0101xx (0x14)   1024    264      9
> + *   AT45DB041B  4Mbit   (512K)  xx0111xx (0x1c)   2048    264      9
> + *   AT45DB081B  8Mbit   (1M)    xx1001xx (0x24)   4096    264      9
> + *   AT45DB0161B 16Mbit  (2M)    xx1011xx (0x2c)   4096    528     10
> + *   AT45DB0321B 32Mbit  (4M)    xx1101xx (0x34)   8192    528     10
> + *   AT45DB0642  64Mbit  (8M)    xx111xxx (0x3c)   8192   1056     11
> + *   AT45DB1282  128Mbit (16M)   xx0100xx (0x10)  16384   1056     11
> + */
> +static int spi_dataflash_probe(struct udevice *dev)
> +{
> +       struct spi_slave *spi = dev_get_parentdata(dev);
> +       struct spi_flash *spi_flash;
> +       struct flash_info *info;
> +       u8 idcode[5];
> +       int ret, status = 0;
> +
> +       spi_flash = dev_get_uclass_priv(dev);
> +       spi_flash->dev = dev;
> +
> +       ret = spi_claim_bus(spi);
> +       if (ret)
> +               return ret;
> +
> +       ret = spi_flash_cmd(spi, CMD_READ_ID, idcode, sizeof(idcode));
> +       if (ret) {
> +               printf("SPI DataFlash: Failed to get idcodes\n");
> +               goto err_read_cmd;
> +       }
> +
> +       /*
> +        * Try to detect dataflash by JEDEC ID.
> +        * If it succeeds we know we have either a C or D part.
> +        * D will support power of 2 pagesize option.
> +        * Both support the security register, though with different
> +        * write procedures.
> +        */
> +       info = jedec_probe(spi, idcode);
> +       if (info != NULL)
> +               add_dataflash(dev, info->name, info->nr_pages,
> +                             info->pagesize, info->pageoffset,
> +                             (info->flags & SUP_POW2PS) ? 'd' : 'c');
> +       else {
> +               /*
> +               * Older chips support only legacy commands, identifing
> +               * capacity using bits in the status byte.
> +               */
> +               status = dataflash_status(spi);
> +               if (status <= 0 || status == 0xff) {
> +                       printf("SPI DataFlash: read status error %d\n", status);
> +                       if (status == 0 || status == 0xff)
> +                               status = -ENODEV;
> +                       goto err_read_cmd;
> +               }
> +               /*
> +               * if there's a device there, assume it's dataflash.
> +               * board setup should have set spi->max_speed_max to
> +               * match f(car) for continuous reads, mode 0 or 3.
> +               */
> +               switch (status & 0x3c) {
> +               case 0x0c:      /* 0 0 1 1 x x */
> +                       status = add_dataflash(dev, "AT45DB011B",
> +                                              512, 264, 9, 0);
> +                       break;
> +               case 0x14:      /* 0 1 0 1 x x */
> +                       status = add_dataflash(dev, "AT45DB021B",
> +                                              1024, 264, 9, 0);
> +                       break;
> +               case 0x1c:      /* 0 1 1 1 x x */
> +                       status = add_dataflash(dev, "AT45DB041x",
> +                                              2048, 264, 9, 0);
> +                       break;
> +               case 0x24:      /* 1 0 0 1 x x */
> +                       status = add_dataflash(dev, "AT45DB081B",
> +                                              4096, 264, 9, 0);
> +                       break;
> +               case 0x2c:      /* 1 0 1 1 x x */
> +                       status = add_dataflash(dev, "AT45DB161x",
> +                                              4096, 528, 10, 0);
> +                       break;
> +               case 0x34:      /* 1 1 0 1 x x */
> +                       status = add_dataflash(dev, "AT45DB321x",
> +                                              8192, 528, 10, 0);
> +                       break;
> +               case 0x38:      /* 1 1 1 x x x */
> +               case 0x3c:
> +                       status = add_dataflash(dev, "AT45DB642x",
> +                                              8192, 1056, 11, 0);
> +                       break;
> +               /* obsolete AT45DB1282 not (yet?) supported */
> +               default:
> +                       dev_info(&spi->dev, "unsupported device (%x)\n",
> +                                status & 0x3c);
> +                       status = -ENODEV;
> +                       goto err_read_cmd;
> +               }
> +       }
> +
> +       /* Assign spi data */
> +       spi_flash->spi = spi;
> +       spi_flash->memory_map = spi->memory_map;
> +       spi_flash->dual_flash = spi->option;
> +
> +       spi_release_bus(spi);
> +
> +       return 0;
> +
> +err_read_cmd:
> +       spi_release_bus(spi);
> +
> +       return status;
> +}
> +
> +static const struct dm_spi_flash_ops spi_dataflash_ops = {
> +       .read = spi_dataflash_read,
> +       .write = spi_dataflash_write,
> +       .erase = spi_dataflash_erase,
> +};
> +
> +static const struct udevice_id spi_dataflash_ids[] = {
> +       { .compatible = "atmel,at45", },
> +       { .compatible = "atmel,dataflash", },
> +       { }
> +};
> +
> +U_BOOT_DRIVER(spi_dataflash) = {
> +       .name           = "spi_dataflash",
> +       .id             = UCLASS_SPI_FLASH,
> +       .of_match       = spi_dataflash_ids,
> +       .probe          = spi_dataflash_probe,
> +       .priv_auto_alloc_size = sizeof(struct dataflash),
> +       .ops            = &spi_dataflash_ops,
> +};
> --
> 2.1.0.27.g96db324
>



-- 
Jagan Teki,
Openedev.


More information about the U-Boot mailing list