[U-Boot] [PATCH v2 3/4] imx: mx6: add display of CPU temperature grade in print_cpuinfo()
Stefano Babic
sbabic at denx.de
Fri May 15 15:24:50 CEST 2015
Hi Tim,
On 15/05/2015 15:16, Tim Harvey wrote:
> On Fri, May 15, 2015 at 1:14 AM, Christian Gmeiner
> <christian.gmeiner at gmail.com> wrote:
>> 2015-05-14 7:11 GMT+02:00 Tim Harvey <tharvey at gateworks.com>:
>>> When CONFIG_IMX6_THERMAL is defined print the CPU temperature grade info
>>> along with the current temperature.
>>>
>>> Before:
>>> CPU: Temperature 42 C
>>>
>>> After:
>>> CPU: Automotive temperature grade (-40C to 125C) at 42C
>>> CPU: Industiral temperature grade (-40C to 105C) at 42C
>>> CPU: Extended Commercial temperature grade (-20C to 105C) at 42C
>>>
>>> Signed-off-by: Tim Harvey <tharvey at gateworks.com>
>>> ---
>>> v2:
>>> - moved display of CPU temperature grade to own patch and combined with the
>>> current temperature from the thermal sensor driver
>>> - add example output to description
>>>
>>> Signed-off-by: Tim Harvey <tharvey at gateworks.com>
>>> ---
>>> arch/arm/imx-common/cpu.c | 27 +++++++++++++++++++++++----
>>> 1 file changed, 23 insertions(+), 4 deletions(-)
>>>
>>> diff --git a/arch/arm/imx-common/cpu.c b/arch/arm/imx-common/cpu.c
>>> index 6b20482..f1b49bb 100644
>>> --- a/arch/arm/imx-common/cpu.c
>>> +++ b/arch/arm/imx-common/cpu.c
>>> @@ -16,6 +16,7 @@
>>> #include <asm/arch/clock.h>
>>> #include <asm/arch/sys_proto.h>
>>> #include <asm/arch/crm_regs.h>
>>> +#include <imx_thermal.h>
>>> #include <ipu_pixfmt.h>
>>> #include <thermal.h>
>>> #include <sata.h>
>>> @@ -146,7 +147,7 @@ int print_cpuinfo(void)
>>>
>>> #if defined(CONFIG_MX6) && defined(CONFIG_IMX6_THERMAL)
>>> struct udevice *thermal_dev;
>>> - int cpu_tmp, ret;
>>> + int cpu_tmp, minc, maxc, ret;
>>> #endif
>>>
>>> cpurev = get_cpu_rev();
>>> @@ -172,16 +173,34 @@ int print_cpuinfo(void)
>>> #endif
>>>
>>> #if defined(CONFIG_MX6) && defined(CONFIG_IMX6_THERMAL)
>>> + puts("CPU: ");
>>> + if (!is_cpu_type(MXC_CPU_MX6SX)) {
>>> + switch (get_cpu_temp_grade(&minc, &maxc)) {
>>> + case TEMP_AUTOMOTIVE:
>>> + puts("Automotive temperature grade ");
>>> + break;
>>> + case TEMP_INDUSTRIAL:
>>> + puts("Industrial temperature grade ");
>>> + break;
>>> + case TEMP_EXTCOMMERCIAL:
>>> + puts("Extended Commercial temperature grade ");
>>> + break;
>>> + default:
>>> + puts("Commercial temperature grade ");
>>> + break;
>>> + }
>>> + printf("(%dC to %dC)", minc, maxc);
>>> + }
>>
>> For the additions above we do not need CONFIG_IMX6_THERMAL.
>
> Hi Christian,
>
> Thanks for the review.
>
> Its true that CONFIG_IMX6_THERMAL is not needed for cpu temperature
> grade but I felt that there would be resistance in general to adding
> additional lines in print_cpuinfo without allowing them to be easily
> disabled.
Agree on this point.
> I felt that temperature grade and current temperature made
> sense to go together in this fasion.
>
> Looking over this though did remind me that now that Freescale has
> told me that the IMX6SX has the same OTP registers/definitions for
> temperature grade programmed I can remove the skip for MX6SX. I would
> however sure like to have someone with an actual MX6SX enable that
> code and give us some testing feedback.
>
Right. My proposal is to merge the currrent patchset, enabling for
IMX6SX again when someone will test it.
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
More information about the U-Boot
mailing list