[U-Boot] [PULL] Please pull u-boot-imx
Stefano Babic
sbabic at denx.de
Fri May 15 17:18:26 CEST 2015
Hi Tom,
please pull from u-boot-imx, thanks !
The following changes since commit ace97d26176a3ebc9ec07738450de93eea35975c:
Merge branch 'zynq' of git://www.denx.de/git/u-boot-microblaze
(2015-04-29 06:46:33 -0400)
are available in the git repository at:
git://www.denx.de/git/u-boot-imx.git master
for you to fetch changes up to 6f63370510ebd7b6dfc83ef4cc6bfd448ecc5dc2:
imx: ventana: use stack relocation (2015-05-15 16:42:14 +0200)
----------------------------------------------------------------
Brecht Neyrinck (1):
bugfix i.mx6 pwm: prevent overflow of period_c * duty_ns
Fabio Estevam (11):
mx6cuboxi: Add HDMI output support
mx6cuboxi: Add USB host support
mx6cuboxi: Allow HDMI and USB keyboard to be stdout/stdin
logos: Add Solidrun's logo
mx6cuboxi: Fix Ethernet PHY detection problem
mx6cuboxi: Pull down PAD_ENET_RXD0/RXD1
mx6cuboxi: Skip usb initialization when booting without HDMI
hummingboard: Remove mx6solo specific support
mx6cuboxi: Mention Cubox-i in the README
warp: README: Fix typo
mx6: Set shared override bit in PL310 AUX_CTRL register
Heiko Schocher (2):
arm, imx6, i2c: add I2C4 for MX6DL
i2c, mxc: rework i2c base address names for different SoCs
Nikolay Dimitrov (2):
arm: mx6: Clamp MMDC and DDR3 clocks for timing calculations
arm: mx6: ddr3: Remove dead code
Soeren Moch (4):
tbs2910: support for usb otg host mode
tbs2910: only enable vga output for stdout/stderr when hdmi detected
tbs2910: use default CONFIG_SYS_PBSIZE
tbs2910: add CONFIG_SUPPORT_EMMC_BOOT
Stefan Roese (2):
arm: mx6: tqma6: Fix USB and add other filesystems
arm: mx6: tqma6: Update to optionally configure an alternative SPI
setup
Stefano Babic (2):
Merge branch 'master' of git://git.denx.de/u-boot
Merge branch 'master' of git://git.denx.de/u-boot
Tim Harvey (17):
imx: ventana: fix boot to SD
imx: ventana: set dtype env var to boot media
imx: ventana: display SPL boot device
imx: ventana: config: enable gpio command
imx: ventana: config: enable driver model
imx: ventana: register gpio's with gpio_request
imx: ventana: enable DM_SERIAL
imx: ventana: config: enable Thermal support
imx: ventana: fix pcie reset for GW522x
imx: ventana: default msata/pci mux to pci before PCI enumeration
imx: ventana: split out common functions between SPL and uboot
imx: ventana: move GSC boot watchdog disable function to gsc.c
imx: ventana: detect pmic using i2c probe instead of board model
imx: ventana: use common uart and i2c setup functions in SPL
imx: ventana: add gpio setup to SPL
imx: ventana: add GSC boot watchdog disable to SPL
imx: ventana: use stack relocation
Ulises Cardenas (2):
Fix mxc_hab documenation
imx: dek_blob: Add explicit include for mapmem
arch/arm/Kconfig | 5 -
arch/arm/cpu/armv7/mx6/clock.c | 33 +++--
arch/arm/cpu/armv7/mx6/ddr.c | 52 +++----
arch/arm/cpu/armv7/mx6/soc.c | 8 +
arch/arm/imx-common/cmd_dek.c | 1 +
arch/arm/imx-common/i2c-mxv7.c | 5 +-
arch/arm/include/asm/arch-imx/imx-regs.h | 2 +-
arch/arm/include/asm/arch-mx25/imx-regs.h | 6 +-
arch/arm/include/asm/arch-mx27/imx-regs.h | 4 +-
arch/arm/include/asm/arch-mx6/crm_regs.h | 2 +
arch/arm/include/asm/arch-mx6/imx-regs.h | 1 +
arch/arm/include/asm/arch-vf610/imx-regs.h | 2 +-
arch/arm/include/asm/pl310.h | 2 +
board/gateworks/gw_ventana/Makefile | 2 +-
board/gateworks/gw_ventana/common.c | 827
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
board/gateworks/gw_ventana/common.h | 98 +++++++++++++
board/gateworks/gw_ventana/gsc.c | 27 ++++
board/gateworks/gw_ventana/gsc.h | 1 +
board/gateworks/gw_ventana/gw_ventana.c | 911
++++++------------------------------------------------------------------------------------------------------------
board/gateworks/gw_ventana/gw_ventana_spl.c | 86 +++++------
board/solidrun/hummingboard/Kconfig | 15 --
board/solidrun/hummingboard/MAINTAINERS | 6 -
board/solidrun/hummingboard/Makefile | 9 --
board/solidrun/hummingboard/README | 40 -----
board/solidrun/hummingboard/hummingboard.c | 182 -----------------------
board/solidrun/hummingboard/solo.cfg | 25 ----
board/solidrun/mx6cuboxi/README | 10 +-
board/solidrun/mx6cuboxi/mx6cuboxi.c | 158 +++++++++++++++++++-
board/tbs/tbs2910/tbs2910.c | 10 ++
board/tqc/tqma6/tqma6.c | 2 +-
board/warp/README | 4 +-
configs/gwventana_defconfig | 2 +
configs/hummingboard_solo_defconfig | 3 -
doc/README.mxc_hab | 12 +-
drivers/i2c/mxc_i2c.c | 40 ++---
drivers/pwm/pwm-imx-util.c | 2 +-
include/configs/gw_ventana.h | 22 ++-
include/configs/hummingboard.h | 224
----------------------------
include/configs/mx6cuboxi.h | 43 +++++-
include/configs/tbs2910.h | 21 ++-
include/configs/tqma6.h | 7 +-
tools/logos/solidrun.bmp | Bin 0 -> 5558 bytes
42 files changed, 1390 insertions(+), 1522 deletions(-)
create mode 100644 board/gateworks/gw_ventana/common.c
create mode 100644 board/gateworks/gw_ventana/common.h
delete mode 100644 board/solidrun/hummingboard/Kconfig
delete mode 100644 board/solidrun/hummingboard/MAINTAINERS
delete mode 100644 board/solidrun/hummingboard/Makefile
delete mode 100644 board/solidrun/hummingboard/README
delete mode 100644 board/solidrun/hummingboard/hummingboard.c
delete mode 100644 board/solidrun/hummingboard/solo.cfg
delete mode 100644 configs/hummingboard_solo_defconfig
delete mode 100644 include/configs/hummingboard.h
create mode 100644 tools/logos/solidrun.bmp
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
More information about the U-Boot
mailing list