[U-Boot] [PATCH 11/11] colibri_vf: Enable board specific USB initialisation for USB pen gpio

[Bhuvanchandra DV]

From: Sanchayan Maity <maitysanchayan at gmail.com>

Add IOMUX for the pad used as USB pen. This needs to be driven low for
the Iris and Viola boards where it is pulled up high by default. This is
required for the USB host functionality to work on these boards. Use the
board specific weak initialisation function, to drive the pin low which
would be called on "usb start".

Signed-off-by: Sanchayan Maity <maitysanchayan at gmail.com>
---
 arch/arm/include/asm/arch-vf610/iomux-vf610.h |  1 +
 board/toradex/colibri_vf/colibri_vf.c         | 25 +++++++++++++++++++++++++
 2 files changed, 26 insertions(+)

diff --git a/arch/arm/include/asm/arch-vf610/iomux-vf610.h b/arch/arm/include/asm/arch-vf610/iomux-vf610.h
index b8b22b1..019307b 100644
--- a/arch/arm/include/asm/arch-vf610/iomux-vf610.h
+++ b/arch/arm/include/asm/arch-vf610/iomux-vf610.h
@@ -131,6 +131,7 @@ enum {
 	VF610_PAD_PTD1__QSPI0_A_CS0		= IOMUX_PAD(0x0140, 0x0140, 1, __NA_, 0, VF610_QSPI_PAD_CTRL),
 	VF610_PAD_PTD2__QSPI0_A_DATA3		= IOMUX_PAD(0x0144, 0x0144, 1, __NA_, 0, VF610_QSPI_PAD_CTRL),
 	VF610_PAD_PTD3__QSPI0_A_DATA2		= IOMUX_PAD(0x0148, 0x0148, 1, __NA_, 0, VF610_QSPI_PAD_CTRL),
+	VF610_PAD_PTD4__GPIO_83         = IOMUX_PAD(0x014C, 0x014C, 0, __NA_, 0, VF610_GPIO_PAD_CTRL),
 	VF610_PAD_PTD4__QSPI0_A_DATA1		= IOMUX_PAD(0x014c, 0x014c, 1, __NA_, 0, VF610_QSPI_PAD_CTRL),
 	VF610_PAD_PTD5__QSPI0_A_DATA0		= IOMUX_PAD(0x0150, 0x0150, 1, __NA_, 0, VF610_QSPI_PAD_CTRL),
 	VF610_PAD_PTD7__QSPI0_B_QSCK		= IOMUX_PAD(0x0158, 0x0158, 1, __NA_, 0, VF610_QSPI_PAD_CTRL),
diff --git a/board/toradex/colibri_vf/colibri_vf.c b/board/toradex/colibri_vf/colibri_vf.c
index 7173022..8618fd0 100644
--- a/board/toradex/colibri_vf/colibri_vf.c
+++ b/board/toradex/colibri_vf/colibri_vf.c
@@ -20,6 +20,7 @@
 #include <netdev.h>
 #include <i2c.h>
 #include <g_dnl.h>
+#include <asm/gpio.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -32,6 +33,12 @@ DECLARE_GLOBAL_DATA_PTR;
 #define ENET_PAD_CTRL	(PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_HIGH | \
 			PAD_CTL_DSE_50ohm | PAD_CTL_OBE_IBE_ENABLE)
 
+#define USB_PEN_GPIO           83
+
+static const iomux_v3_cfg_t usb_pads[] = {
+	VF610_PAD_PTD4__GPIO_83,
+};
+
 int dram_init(void)
 {
 	static const struct ddr3_jedec_timings timings = {
@@ -464,3 +471,21 @@ int g_dnl_bind_fixup(struct usb_device_descriptor *dev, const char *name)
 
 	return 0;
 }
+
+#ifdef CONFIG_USB_EHCI_VF
+int board_ehci_hcd_init(int port)
+{
+	imx_iomux_v3_setup_multiple_pads(usb_pads, ARRAY_SIZE(usb_pads));
+
+	switch (port) {
+	case 0:
+		/* USBC does not have PEN, also configured as USB client only */
+		break;
+	case 1:
+		gpio_request(USB_PEN_GPIO, "usb-pen-gpio");
+		gpio_direction_output(USB_PEN_GPIO, 0);
+		break;
+	}
+	return 0;
+}
+#endif
-- 
2.1.0