[U-Boot] [PATCH v3] sunxi: Make DRAM_ODT_EN Kconfig setting a bool
Hans de Goede
hdegoede at redhat.com
Tue May 19 14:56:39 CEST 2015
Make DRAM_ODT_EN Kconfig setting a bool, add a separate DRAM_ODT_CORRECTION
setting for A23 SoCs and use DRAM_ODT_EN Kconfig everywhere instead of
only in dram_sun4i.c and hardcoding odt_en elsewhere.
Note this commit makes no functional changes for existing boards,
its purpose is to allow changing the odt_en value on future A33 boards.
Signed-off-by: Hans de Goede <hdegoede at redhat.com>
---
Changes in v2:
-Use existing DRAM_ODT_EN Kconfig block moving it out of the
#if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I block it was in
Changes in v3:
-Complete rewrite of the patch
---
arch/arm/cpu/armv7/sunxi/dram_sun4i.c | 4 ++--
arch/arm/cpu/armv7/sunxi/dram_sun8i_a23.c | 19 +++++++++----------
arch/arm/cpu/armv7/sunxi/dram_sun8i_a33.c | 4 ++--
arch/arm/include/asm/arch-sunxi/dram_sun4i.h | 3 +--
arch/arm/include/asm/arch-sunxi/dram_sun8i_a23.h | 1 +
board/sunxi/Kconfig | 22 +++++++++++++++-------
board/sunxi/dram_sun4i_auto.c | 3 ++-
board/sunxi/dram_sun5i_auto.c | 3 ++-
8 files changed, 34 insertions(+), 25 deletions(-)
diff --git a/arch/arm/cpu/armv7/sunxi/dram_sun4i.c b/arch/arm/cpu/armv7/sunxi/dram_sun4i.c
index c736fa3..f7b4915 100644
--- a/arch/arm/cpu/armv7/sunxi/dram_sun4i.c
+++ b/arch/arm/cpu/armv7/sunxi/dram_sun4i.c
@@ -508,7 +508,7 @@ static void mctl_ddr3_initialize(void)
/*
* Perform impedance calibration on the DRAM controller side of the wire.
*/
-static void mctl_set_impedance(u32 zq, u32 odt_en)
+static void mctl_set_impedance(u32 zq, bool odt_en)
{
struct sunxi_dram_reg *dram = (struct sunxi_dram_reg *)SUNXI_DRAMC_BASE;
u32 reg_val;
@@ -556,7 +556,7 @@ static void mctl_set_impedance(u32 zq, u32 odt_en)
clrbits_le32(&dram->zqcr0, DRAM_ZQCR0_ZCAL);
/* Set I/O configure register */
- writel(DRAM_IOCR_ODT_EN(odt_en), &dram->iocr);
+ writel(DRAM_IOCR_ODT_EN, &dram->iocr);
}
static unsigned long dramc_init_helper(struct dram_para *para)
diff --git a/arch/arm/cpu/armv7/sunxi/dram_sun8i_a23.c b/arch/arm/cpu/armv7/sunxi/dram_sun8i_a23.c
index 3d7964d..165c052 100644
--- a/arch/arm/cpu/armv7/sunxi/dram_sun8i_a23.c
+++ b/arch/arm/cpu/armv7/sunxi/dram_sun8i_a23.c
@@ -26,12 +26,14 @@
#include <asm/arch/clock.h>
#include <asm/arch/dram.h>
#include <asm/arch/prcm.h>
+#include <linux/kconfig.h>
static const struct dram_para dram_para = {
.clock = CONFIG_DRAM_CLK,
.type = 3,
.zq = CONFIG_DRAM_ZQ,
- .odt_en = 1,
+ .odt_en = IS_ENABLED(CONFIG_DRAM_ODT_EN),
+ .odt_correction = CONFIG_DRAM_ODT_CORRECTION,
.para1 = 0, /* not used (only used when tpr13 bit 31 is set */
.para2 = 0, /* not used (only used when tpr13 bit 31 is set */
.mr0 = 6736,
@@ -97,7 +99,6 @@ static void mctl_init(u32 *bus_width)
(struct sunxi_mctl_ctl_reg *)SUNXI_DRAM_CTL0_BASE;
struct sunxi_mctl_phy_reg * const mctl_phy =
(struct sunxi_mctl_phy_reg *)SUNXI_DRAM_PHY0_BASE;
- int correction;
if (dram_para.tpr13 & 0x20)
writel(0x40b, &mctl_phy->dcr);
@@ -138,7 +139,7 @@ static void mctl_init(u32 *bus_width)
writel(0x01000081, &mctl_phy->dtcr);
- if (dram_para.clock <= 240 || !(dram_para.odt_en & 0x01)) {
+ if (dram_para.clock <= 240 || !dram_para.odt_en) {
clrbits_le32(&mctl_phy->dx0gcr, 0x600);
clrbits_le32(&mctl_phy->dx1gcr, 0x600);
}
@@ -251,13 +252,11 @@ static void mctl_init(u32 *bus_width)
} else
*bus_width = 16;
- correction = (dram_para.odt_en >> 8) & 0xff;
- if (correction) {
- if (dram_para.odt_en & 0x80000000)
- correction = -correction;
-
- mctl_apply_odt_correction(&mctl_phy->dx0lcdlr1, correction);
- mctl_apply_odt_correction(&mctl_phy->dx1lcdlr1, correction);
+ if (dram_para.odt_correction) {
+ mctl_apply_odt_correction(&mctl_phy->dx0lcdlr1,
+ dram_para.odt_correction);
+ mctl_apply_odt_correction(&mctl_phy->dx1lcdlr1,
+ dram_para.odt_correction);
}
mctl_await_completion(&mctl_ctl->statr, 0x01, 0x01);
diff --git a/arch/arm/cpu/armv7/sunxi/dram_sun8i_a33.c b/arch/arm/cpu/armv7/sunxi/dram_sun8i_a33.c
index 979bb3c..ebba438 100644
--- a/arch/arm/cpu/armv7/sunxi/dram_sun8i_a33.c
+++ b/arch/arm/cpu/armv7/sunxi/dram_sun8i_a33.c
@@ -14,12 +14,12 @@
#include <asm/arch/clock.h>
#include <asm/arch/dram.h>
#include <asm/arch/prcm.h>
+#include <linux/kconfig.h>
/* PLL runs at 2x dram-clk, controller runs at PLL / 4 (dram-clk / 2) */
#define DRAM_CLK_MUL 2
#define DRAM_CLK_DIV 4
#define DRAM_SIGMA_DELTA_ENABLE 1
-#define DRAM_ODT_EN 0
struct dram_para {
u8 cs1;
@@ -215,7 +215,7 @@ static int mctl_channel_init(struct dram_para *para)
clrbits_le32(&mctl_ctl->pgcr0, 0x3f << 0);
/* Set ODT */
- if ((CONFIG_DRAM_CLK > 400) && DRAM_ODT_EN) {
+ if ((CONFIG_DRAM_CLK > 400) && IS_ENABLED(CONFIG_DRAM_ODT_EN)) {
setbits_le32(DXnGCR0(0), 0x3 << 9);
setbits_le32(DXnGCR0(1), 0x3 << 9);
} else {
diff --git a/arch/arm/include/asm/arch-sunxi/dram_sun4i.h b/arch/arm/include/asm/arch-sunxi/dram_sun4i.h
index 40c385a..139e336 100644
--- a/arch/arm/include/asm/arch-sunxi/dram_sun4i.h
+++ b/arch/arm/include/asm/arch-sunxi/dram_sun4i.h
@@ -164,8 +164,7 @@ struct dram_para {
#define DRAM_ZQSR_ZDONE (1 << 31) /* ZQ calibration completion flag */
-#define DRAM_IOCR_ODT_EN(n) ((((n) & 0x3) << 30) | ((n) & 0x3) << 0)
-#define DRAM_IOCR_ODT_EN_MASK DRAM_IOCR_ODT_EN(0x3)
+#define DRAM_IOCR_ODT_EN ((3 << 30) | (3 << 0))
#define DRAM_MR_BURST_LENGTH(n) (((n) & 0x7) << 0)
#define DRAM_MR_BURST_LENGTH_MASK DRAM_MR_BURST_LENGTH(0x7)
diff --git a/arch/arm/include/asm/arch-sunxi/dram_sun8i_a23.h b/arch/arm/include/asm/arch-sunxi/dram_sun8i_a23.h
index 06adee2..316a333 100644
--- a/arch/arm/include/asm/arch-sunxi/dram_sun8i_a23.h
+++ b/arch/arm/include/asm/arch-sunxi/dram_sun8i_a23.h
@@ -19,6 +19,7 @@ struct dram_para {
u32 type;
u32 zq;
u32 odt_en;
+ s32 odt_correction;
u32 para1;
u32 para2;
u32 mr0;
diff --git a/board/sunxi/Kconfig b/board/sunxi/Kconfig
index 7368d4d..3012346 100644
--- a/board/sunxi/Kconfig
+++ b/board/sunxi/Kconfig
@@ -96,6 +96,13 @@ config DRAM_ZQ
---help---
Set the dram zq value.
+config DRAM_ODT_EN
+ bool "sunxi dram odt enable"
+ default n if !MACH_SUN8I_A23
+ default y if MACH_SUN8I_A23
+ ---help---
+ Select this to enable dram odt (on die termination).
+
if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
config DRAM_EMR1
int "sunxi dram emr1 value"
@@ -104,13 +111,6 @@ config DRAM_EMR1
---help---
Set the dram controller emr1 value.
-config DRAM_ODT_EN
- int "sunxi dram odt_en value"
- default 0
- ---help---
- Set the dram controller odt_en parameter. This can be used to
- enable/disable the ODT feature.
-
config DRAM_TPR3
hex "sunxi dram tpr3 value"
default 0
@@ -171,6 +171,14 @@ endchoice
endif
+if MACH_SUN8I_A23
+config DRAM_ODT_CORRECTION
+ int "sunxi dram odt correction value"
+ default 0
+ ---help---
+ Set the dram odt correction value (range -255 - 255).
+endif
+
config SYS_CLK_FREQ
default 912000000 if MACH_SUN7I
default 1008000000 if MACH_SUN4I || MACH_SUN5I || MACH_SUN6I || MACH_SUN8I
diff --git a/board/sunxi/dram_sun4i_auto.c b/board/sunxi/dram_sun4i_auto.c
index 09e0c9a..149bb51 100644
--- a/board/sunxi/dram_sun4i_auto.c
+++ b/board/sunxi/dram_sun4i_auto.c
@@ -1,5 +1,6 @@
#include <common.h>
#include <asm/arch/dram.h>
+#include <linux/kconfig.h>
static struct dram_para dram_para = {
.clock = CONFIG_DRAM_CLK,
@@ -9,7 +10,7 @@ static struct dram_para dram_para = {
.io_width = 0,
.bus_width = 0,
.zq = CONFIG_DRAM_ZQ,
- .odt_en = CONFIG_DRAM_ODT_EN,
+ .odt_en = IS_ENABLED(CONFIG_DRAM_ODT_EN),
.size = 0,
#ifdef CONFIG_DRAM_TIMINGS_VENDOR_MAGIC
.cas = 6,
diff --git a/board/sunxi/dram_sun5i_auto.c b/board/sunxi/dram_sun5i_auto.c
index 660b18e..596a206 100644
--- a/board/sunxi/dram_sun5i_auto.c
+++ b/board/sunxi/dram_sun5i_auto.c
@@ -2,6 +2,7 @@
#include <common.h>
#include <asm/arch/dram.h>
+#include <linux/kconfig.h>
static struct dram_para dram_para = {
.clock = CONFIG_DRAM_CLK,
@@ -12,7 +13,7 @@ static struct dram_para dram_para = {
.io_width = 0,
.bus_width = 0,
.zq = CONFIG_DRAM_ZQ,
- .odt_en = CONFIG_DRAM_ODT_EN,
+ .odt_en = IS_ENABLED(CONFIG_DRAM_ODT_EN),
.size = 0,
#ifdef CONFIG_DRAM_TIMINGS_VENDOR_MAGIC
.cas = 9,
--
2.4.1
More information about the U-Boot
mailing list