[U-Boot] [PATCH v4 4/7] ti: am335x: Use generic EEPROM detection logic
Lokesh Vutla
a0131933 at ti.com
Fri Nov 6 04:48:49 CET 2015
On Friday 06 November 2015 06:09 AM, Steve Kipisz wrote:
> From: Nishanth Menon <nm at ti.com>
>
> Use the generic EEPROM detection logic instead of duplicating the AM
> eeprom logic.
>
> Signed-off-by: Nishanth Menon <nm at ti.com>
> Signed-off-by: Steven Kipisz <s-kipisz2 at ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla at ti.com>
Thanks and regards,
Lokesh
> ---
> Changes in v4:
> - New Patch
> - Depends on https://patchwork.ozlabs.org/patch/540280/
>
> board/ti/am335x/board.c | 99 +++++++++++++++----------------------------------
> board/ti/am335x/board.h | 42 ++++++---------------
> board/ti/am335x/mux.c | 11 +++---
> 3 files changed, 48 insertions(+), 104 deletions(-)
>
> diff --git a/board/ti/am335x/board.c b/board/ti/am335x/board.c
> index f0cb1e204ad5..1f9707d60c1f 100644
> --- a/board/ti/am335x/board.c
> +++ b/board/ti/am335x/board.c
> @@ -31,6 +31,7 @@
> #include <environment.h>
> #include <watchdog.h>
> #include <environment.h>
> +#include <board_detect.h>
> #include "board.h"
>
> DECLARE_GLOBAL_DATA_PTR;
> @@ -46,43 +47,9 @@ static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
> /*
> * Read header information from EEPROM into global structure.
> */
> -static int read_eeprom(struct am335x_baseboard_id *header)
> +static int __maybe_unused read_eeprom(struct ti_am_eeprom **header)
> {
> - /* Check if baseboard eeprom is available */
> - if (i2c_probe(CONFIG_SYS_I2C_EEPROM_ADDR)) {
> - puts("Could not probe the EEPROM; something fundamentally "
> - "wrong on the I2C bus.\n");
> - return -ENODEV;
> - }
> -
> - /* read the eeprom using i2c */
> - if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 2, (uchar *)header,
> - sizeof(struct am335x_baseboard_id))) {
> - puts("Could not read the EEPROM; something fundamentally"
> - " wrong on the I2C bus.\n");
> - return -EIO;
> - }
> -
> - if (header->magic != 0xEE3355AA) {
> - /*
> - * read the eeprom using i2c again,
> - * but use only a 1 byte address
> - */
> - if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 1, (uchar *)header,
> - sizeof(struct am335x_baseboard_id))) {
> - puts("Could not read the EEPROM; something "
> - "fundamentally wrong on the I2C bus.\n");
> - return -EIO;
> - }
> -
> - if (header->magic != 0xEE3355AA) {
> - printf("Incorrect magic number (0x%x) in EEPROM\n",
> - header->magic);
> - return -EINVAL;
> - }
> - }
> -
> - return 0;
> + return ti_i2c_eeprom_am_get(-1, CONFIG_SYS_I2C_EEPROM_ADDR, header);
> }
>
> #ifndef CONFIG_SKIP_LOWLEVEL_INIT
> @@ -223,7 +190,7 @@ const struct dpll_params dpll_ddr_bone_black = {
>
> void am33xx_spl_board_init(void)
> {
> - struct am335x_baseboard_id header;
> + struct ti_am_eeprom *header;
> int mpu_vdd;
>
> if (read_eeprom(&header) < 0)
> @@ -232,7 +199,7 @@ void am33xx_spl_board_init(void)
> /* Get the frequency */
> dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev);
>
> - if (board_is_bone(&header) || board_is_bone_lt(&header)) {
> + if (board_is_bone() || board_is_bone_lt()) {
> /* BeagleBone PMIC Code */
> int usb_cur_lim;
>
> @@ -240,7 +207,7 @@ void am33xx_spl_board_init(void)
> * Only perform PMIC configurations if board rev > A1
> * on Beaglebone White
> */
> - if (board_is_bone(&header) && !strncmp(header.version,
> + if (board_is_bone() && !strncmp(header->version,
> "00A1", 4))
> return;
>
> @@ -251,7 +218,7 @@ void am33xx_spl_board_init(void)
> * On Beaglebone White we need to ensure we have AC power
> * before increasing the frequency.
> */
> - if (board_is_bone(&header)) {
> + if (board_is_bone()) {
> uchar pmic_status_reg;
> if (tps65217_reg_read(TPS65217_STATUS,
> &pmic_status_reg))
> @@ -266,7 +233,7 @@ void am33xx_spl_board_init(void)
> * Override what we have detected since we know if we have
> * a Beaglebone Black it supports 1GHz.
> */
> - if (board_is_bone_lt(&header))
> + if (board_is_bone_lt())
> dpll_mpu_opp100.m = MPUPLL_M_1000;
>
> /*
> @@ -307,7 +274,7 @@ void am33xx_spl_board_init(void)
> * Set LDO3, LDO4 output voltage to 3.3V for Beaglebone.
> * Set LDO3 to 1.8V and LDO4 to 3.3V for Beaglebone Black.
> */
> - if (board_is_bone(&header)) {
> + if (board_is_bone()) {
> if (tps65217_reg_write(TPS65217_PROT_LEVEL_2,
> TPS65217_DEFLS1,
> TPS65217_LDO_VOLTAGE_OUT_3_3,
> @@ -367,18 +334,18 @@ void am33xx_spl_board_init(void)
>
> const struct dpll_params *get_dpll_ddr_params(void)
> {
> - struct am335x_baseboard_id header;
> + struct ti_am_eeprom *header;
>
> enable_i2c0_pin_mux();
> i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
> if (read_eeprom(&header) < 0)
> puts("Could not get board ID.\n");
>
> - if (board_is_evm_sk(&header))
> + if (board_is_evm_sk())
> return &dpll_ddr_evm_sk;
> - else if (board_is_bone_lt(&header))
> + else if (board_is_bone_lt())
> return &dpll_ddr_bone_black;
> - else if (board_is_evm_15_or_later(&header))
> + else if (board_is_evm_15_or_later(header))
> return &dpll_ddr_evm_sk;
> else
> return &dpll_ddr;
> @@ -403,12 +370,12 @@ void set_uart_mux_conf(void)
>
> void set_mux_conf_regs(void)
> {
> - __maybe_unused struct am335x_baseboard_id header;
> + __maybe_unused struct ti_am_eeprom *header;
>
> if (read_eeprom(&header) < 0)
> puts("Could not get board ID.\n");
>
> - enable_board_pin_mux(&header);
> + enable_board_pin_mux(header);
> }
>
> const struct ctrl_ioregs ioregs_evmsk = {
> @@ -445,12 +412,12 @@ const struct ctrl_ioregs ioregs = {
>
> void sdram_init(void)
> {
> - __maybe_unused struct am335x_baseboard_id header;
> + __maybe_unused struct ti_am_eeprom *header;
>
> if (read_eeprom(&header) < 0)
> puts("Could not get board ID.\n");
>
> - if (board_is_evm_sk(&header)) {
> + if (board_is_evm_sk()) {
> /*
> * EVM SK 1.2A and later use gpio0_7 to enable DDR3.
> * This is safe enough to do on older revs.
> @@ -459,15 +426,15 @@ void sdram_init(void)
> gpio_direction_output(GPIO_DDR_VTT_EN, 1);
> }
>
> - if (board_is_evm_sk(&header))
> + if (board_is_evm_sk())
> config_ddr(303, &ioregs_evmsk, &ddr3_data,
> &ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0);
> - else if (board_is_bone_lt(&header))
> + else if (board_is_bone_lt())
> config_ddr(400, &ioregs_bonelt,
> &ddr3_beagleblack_data,
> &ddr3_beagleblack_cmd_ctrl_data,
> &ddr3_beagleblack_emif_reg_data, 0);
> - else if (board_is_evm_15_or_later(&header))
> + else if (board_is_evm_15_or_later(header))
> config_ddr(303, &ioregs_evm15, &ddr3_evm_data,
> &ddr3_evm_cmd_ctrl_data, &ddr3_evm_emif_reg_data, 0);
> else
> @@ -496,20 +463,14 @@ int board_init(void)
> int board_late_init(void)
> {
> #ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
> - char safe_string[HDR_NAME_LEN + 1];
> - struct am335x_baseboard_id header;
> + struct ti_am_eeprom_printable p;
> + int rc;
>
> - if (read_eeprom(&header) < 0)
> - puts("Could not get board ID.\n");
> + rc = ti_i2c_eeprom_am_get_print(-1, CONFIG_SYS_I2C_EEPROM_ADDR, &p);
>
> - /* Now set variables based on the header. */
> - strncpy(safe_string, (char *)header.name, sizeof(header.name));
> - safe_string[sizeof(header.name)] = 0;
> - setenv("board_name", safe_string);
> -
> - strncpy(safe_string, (char *)header.version, sizeof(header.version));
> - safe_string[sizeof(header.version)] = 0;
> - setenv("board_rev", safe_string);
> + if (rc)
> + puts("Could not get board ID.\n");
> + set_board_info_env(p.name, p.version, p.serial);
> #endif
>
> return 0;
> @@ -581,7 +542,7 @@ int board_eth_init(bd_t *bis)
> int rv, n = 0;
> uint8_t mac_addr[6];
> uint32_t mac_hi, mac_lo;
> - __maybe_unused struct am335x_baseboard_id header;
> + __maybe_unused struct ti_am_eeprom *header;
>
> /* try reading mac address from efuse */
> mac_lo = readl(&cdev->macid0l);
> @@ -621,8 +582,8 @@ int board_eth_init(bd_t *bis)
> if (read_eeprom(&header) < 0)
> puts("Could not get board ID.\n");
>
> - if (board_is_bone(&header) || board_is_bone_lt(&header) ||
> - board_is_idk(&header)) {
> + if (board_is_bone() || board_is_bone_lt() ||
> + board_is_idk(header)) {
> writel(MII_MODE_ENABLE, &cdev->miisel);
> cpsw_slaves[0].phy_if = cpsw_slaves[1].phy_if =
> PHY_INTERFACE_MODE_MII;
> @@ -651,7 +612,7 @@ int board_eth_init(bd_t *bis)
> #define AR8051_DEBUG_RGMII_CLK_DLY_REG 0x5
> #define AR8051_RGMII_TX_CLK_DLY 0x100
>
> - if (board_is_evm_sk(&header) || board_is_gp_evm(&header)) {
> + if (board_is_evm_sk() || board_is_gp_evm()) {
> const char *devname;
> devname = miiphy_get_current_dev();
>
> diff --git a/board/ti/am335x/board.h b/board/ti/am335x/board.h
> index bc700d56fece..14b2469df12d 100644
> --- a/board/ti/am335x/board.h
> +++ b/board/ti/am335x/board.h
> @@ -11,52 +11,34 @@
> #ifndef _BOARD_H_
> #define _BOARD_H_
>
> -/*
> - * TI AM335x parts define a system EEPROM that defines certain sub-fields.
> - * We use these fields to in turn see what board we are on, and what
> - * that might require us to set or not set.
> - */
> -#define HDR_NO_OF_MAC_ADDR 3
> -#define HDR_ETH_ALEN 6
> -#define HDR_NAME_LEN 8
> -
> -struct am335x_baseboard_id {
> - unsigned int magic;
> - char name[HDR_NAME_LEN];
> - char version[4];
> - char serial[12];
> - char config[32];
> - char mac_addr[HDR_NO_OF_MAC_ADDR][HDR_ETH_ALEN];
> -};
> -
> -static inline int board_is_bone(struct am335x_baseboard_id *header)
> +static inline int board_is_bone(void)
> {
> - return !strncmp(header->name, "A335BONE", HDR_NAME_LEN);
> + return board_am_is("A335BONE");
> }
>
> -static inline int board_is_bone_lt(struct am335x_baseboard_id *header)
> +static inline int board_is_bone_lt(void)
> {
> - return !strncmp(header->name, "A335BNLT", HDR_NAME_LEN);
> + return board_am_is("A335BNLT");
> }
>
> -static inline int board_is_evm_sk(struct am335x_baseboard_id *header)
> +static inline int board_is_evm_sk(void)
> {
> - return !strncmp("A335X_SK", header->name, HDR_NAME_LEN);
> + return board_am_is("A335X_SK");
> }
>
> -static inline int board_is_idk(struct am335x_baseboard_id *header)
> +static inline int board_is_idk(struct ti_am_eeprom *header)
> {
> return !strncmp(header->config, "SKU#02", 6);
> }
>
> -static inline int board_is_gp_evm(struct am335x_baseboard_id *header)
> +static inline int board_is_gp_evm(void)
> {
> - return !strncmp("A33515BB", header->name, HDR_NAME_LEN);
> + return board_am_is("A33515BB");
> }
>
> -static inline int board_is_evm_15_or_later(struct am335x_baseboard_id *header)
> +static inline int board_is_evm_15_or_later(struct ti_am_eeprom *header)
> {
> - return (board_is_gp_evm(header) &&
> + return (board_is_gp_evm() &&
> strncmp("1.5", header->version, 3) <= 0);
> }
>
> @@ -73,5 +55,5 @@ void enable_uart3_pin_mux(void);
> void enable_uart4_pin_mux(void);
> void enable_uart5_pin_mux(void);
> void enable_i2c0_pin_mux(void);
> -void enable_board_pin_mux(struct am335x_baseboard_id *header);
> +void enable_board_pin_mux(struct ti_am_eeprom *header);
> #endif
> diff --git a/board/ti/am335x/mux.c b/board/ti/am335x/mux.c
> index 28c29a2f9cba..6bffa91c24c9 100644
> --- a/board/ti/am335x/mux.c
> +++ b/board/ti/am335x/mux.c
> @@ -19,6 +19,7 @@
> #include <asm/arch/mux.h>
> #include <asm/io.h>
> #include <i2c.h>
> +#include <board_detect.h>
> #include "board.h"
>
> static struct module_pin_mux uart0_pin_mux[] = {
> @@ -312,10 +313,10 @@ static unsigned short detect_daughter_board_profile(void)
> return (1 << (val & PROFILE_MASK));
> }
>
> -void enable_board_pin_mux(struct am335x_baseboard_id *header)
> +void enable_board_pin_mux(struct ti_am_eeprom *header)
> {
> /* Do board-specific muxes. */
> - if (board_is_bone(header)) {
> + if (board_is_bone()) {
> /* Beaglebone pinmux */
> configure_module_pin_mux(i2c1_pin_mux);
> configure_module_pin_mux(mii1_pin_mux);
> @@ -327,7 +328,7 @@ void enable_board_pin_mux(struct am335x_baseboard_id *header)
> #else
> configure_module_pin_mux(mmc1_pin_mux);
> #endif
> - } else if (board_is_gp_evm(header)) {
> + } else if (board_is_gp_evm()) {
> /* General Purpose EVM */
> unsigned short profile = detect_daughter_board_profile();
> configure_module_pin_mux(rgmii1_pin_mux);
> @@ -348,13 +349,13 @@ void enable_board_pin_mux(struct am335x_baseboard_id *header)
> /* Industrial Motor Control (IDK) */
> configure_module_pin_mux(mii1_pin_mux);
> configure_module_pin_mux(mmc0_no_cd_pin_mux);
> - } else if (board_is_evm_sk(header)) {
> + } else if (board_is_evm_sk()) {
> /* Starter Kit EVM */
> configure_module_pin_mux(i2c1_pin_mux);
> configure_module_pin_mux(gpio0_7_pin_mux);
> configure_module_pin_mux(rgmii1_pin_mux);
> configure_module_pin_mux(mmc0_pin_mux_sk_evm);
> - } else if (board_is_bone_lt(header)) {
> + } else if (board_is_bone_lt()) {
> /* Beaglebone LT pinmux */
> configure_module_pin_mux(i2c1_pin_mux);
> configure_module_pin_mux(mii1_pin_mux);
>
More information about the U-Boot
mailing list