[U-Boot] [PATCH v2 2/8] x86: qemu: Move chipset-specific codes from pci.c to qemu.c
Bin Meng
bmeng.cn at gmail.com
Fri Nov 6 11:04:49 CET 2015
Move chipset-specific codes such as PAM init, PCIe ECAM and MP table
from pci.c to qemu.c, to prepare for DM PCI conversion.
Signed-off-by: Bin Meng <bmeng.cn at gmail.com>
---
Changes in v2: None
arch/x86/cpu/qemu/pci.c | 72 ----------------------------------------
arch/x86/cpu/qemu/qemu.c | 82 ++++++++++++++++++++++++++++++++++++++++++++++
include/configs/qemu-x86.h | 2 ++
3 files changed, 84 insertions(+), 72 deletions(-)
diff --git a/arch/x86/cpu/qemu/pci.c b/arch/x86/cpu/qemu/pci.c
index 8515d10..d50ab75 100644
--- a/arch/x86/cpu/qemu/pci.c
+++ b/arch/x86/cpu/qemu/pci.c
@@ -6,14 +6,9 @@
#include <common.h>
#include <pci.h>
-#include <asm/pci.h>
-#include <asm/arch/device.h>
-#include <asm/arch/qemu.h>
DECLARE_GLOBAL_DATA_PTR;
-static bool i440fx;
-
void board_pci_setup_hose(struct pci_controller *hose)
{
hose->first_busno = 0;
@@ -50,72 +45,5 @@ void board_pci_setup_hose(struct pci_controller *hose)
int board_pci_post_scan(struct pci_controller *hose)
{
- u16 device, xbcs;
- int pam, i;
-
- /*
- * i440FX and Q35 chipset have different PAM register offset, but with
- * the same bitfield layout. Here we determine the offset based on its
- * PCI device ID.
- */
- device = x86_pci_read_config16(PCI_BDF(0, 0, 0), PCI_DEVICE_ID);
- i440fx = (device == PCI_DEVICE_ID_INTEL_82441);
- pam = i440fx ? I440FX_PAM : Q35_PAM;
-
- /*
- * Initialize Programmable Attribute Map (PAM) Registers
- *
- * Configure legacy segments C/D/E/F to system RAM
- */
- for (i = 0; i < PAM_NUM; i++)
- x86_pci_write_config8(PCI_BDF(0, 0, 0), pam + i, PAM_RW);
-
- if (i440fx) {
- /*
- * Enable legacy IDE I/O ports decode
- *
- * Note: QEMU always decode legacy IDE I/O port on PIIX chipset.
- * However Linux ata_piix driver does sanity check on these two
- * registers to see whether legacy ports decode is turned on.
- * This is to make Linux ata_piix driver happy.
- */
- x86_pci_write_config16(PIIX_IDE, IDE0_TIM, IDE_DECODE_EN);
- x86_pci_write_config16(PIIX_IDE, IDE1_TIM, IDE_DECODE_EN);
-
- /* Enable I/O APIC */
- xbcs = x86_pci_read_config16(PIIX_ISA, XBCS);
- xbcs |= APIC_EN;
- x86_pci_write_config16(PIIX_ISA, XBCS, xbcs);
- } else {
- /* Configure PCIe ECAM base address */
- x86_pci_write_config32(PCI_BDF(0, 0, 0), PCIEX_BAR,
- CONFIG_PCIE_ECAM_BASE | BAR_EN);
- }
-
return 0;
}
-
-#ifdef CONFIG_GENERATE_MP_TABLE
-int mp_determine_pci_dstirq(int bus, int dev, int func, int pirq)
-{
- u8 irq;
-
- if (i440fx) {
- /*
- * Not like most x86 platforms, the PIRQ[A-D] on PIIX3 are not
- * connected to I/O APIC INTPIN#16-19. Instead they are routed
- * to an irq number controled by the PIRQ routing register.
- */
- irq = x86_pci_read_config8(PCI_BDF(bus, dev, func),
- PCI_INTERRUPT_LINE);
- } else {
- /*
- * ICH9's PIRQ[A-H] are not consecutive numbers from 0 to 7.
- * PIRQ[A-D] still maps to [0-3] but PIRQ[E-H] maps to [8-11].
- */
- irq = pirq < 8 ? pirq + 16 : pirq + 12;
- }
-
- return irq;
-}
-#endif
diff --git a/arch/x86/cpu/qemu/qemu.c b/arch/x86/cpu/qemu/qemu.c
index 7c03e02..84fb082 100644
--- a/arch/x86/cpu/qemu/qemu.c
+++ b/arch/x86/cpu/qemu/qemu.c
@@ -6,8 +6,58 @@
#include <common.h>
#include <asm/irq.h>
+#include <asm/pci.h>
#include <asm/post.h>
#include <asm/processor.h>
+#include <asm/arch/device.h>
+#include <asm/arch/qemu.h>
+
+static bool i440fx;
+
+static void qemu_chipset_init(void)
+{
+ u16 device, xbcs;
+ int pam, i;
+
+ /*
+ * i440FX and Q35 chipset have different PAM register offset, but with
+ * the same bitfield layout. Here we determine the offset based on its
+ * PCI device ID.
+ */
+ device = x86_pci_read_config16(PCI_BDF(0, 0, 0), PCI_DEVICE_ID);
+ i440fx = (device == PCI_DEVICE_ID_INTEL_82441);
+ pam = i440fx ? I440FX_PAM : Q35_PAM;
+
+ /*
+ * Initialize Programmable Attribute Map (PAM) Registers
+ *
+ * Configure legacy segments C/D/E/F to system RAM
+ */
+ for (i = 0; i < PAM_NUM; i++)
+ x86_pci_write_config8(PCI_BDF(0, 0, 0), pam + i, PAM_RW);
+
+ if (i440fx) {
+ /*
+ * Enable legacy IDE I/O ports decode
+ *
+ * Note: QEMU always decode legacy IDE I/O port on PIIX chipset.
+ * However Linux ata_piix driver does sanity check on these two
+ * registers to see whether legacy ports decode is turned on.
+ * This is to make Linux ata_piix driver happy.
+ */
+ x86_pci_write_config16(PIIX_IDE, IDE0_TIM, IDE_DECODE_EN);
+ x86_pci_write_config16(PIIX_IDE, IDE1_TIM, IDE_DECODE_EN);
+
+ /* Enable I/O APIC */
+ xbcs = x86_pci_read_config16(PIIX_ISA, XBCS);
+ xbcs |= APIC_EN;
+ x86_pci_write_config16(PIIX_ISA, XBCS, xbcs);
+ } else {
+ /* Configure PCIe ECAM base address */
+ x86_pci_write_config32(PCI_BDF(0, 0, 0), PCIEX_BAR,
+ CONFIG_PCIE_ECAM_BASE | BAR_EN);
+ }
+}
int arch_cpu_init(void)
{
@@ -39,7 +89,39 @@ void reset_cpu(ulong addr)
x86_full_reset();
}
+int arch_early_init_r(void)
+{
+ qemu_chipset_init();
+
+ return 0;
+}
+
int arch_misc_init(void)
{
return pirq_init();
}
+
+#ifdef CONFIG_GENERATE_MP_TABLE
+int mp_determine_pci_dstirq(int bus, int dev, int func, int pirq)
+{
+ u8 irq;
+
+ if (i440fx) {
+ /*
+ * Not like most x86 platforms, the PIRQ[A-D] on PIIX3 are not
+ * connected to I/O APIC INTPIN#16-19. Instead they are routed
+ * to an irq number controled by the PIRQ routing register.
+ */
+ irq = x86_pci_read_config8(PCI_BDF(bus, dev, func),
+ PCI_INTERRUPT_LINE);
+ } else {
+ /*
+ * ICH9's PIRQ[A-H] are not consecutive numbers from 0 to 7.
+ * PIRQ[A-D] still maps to [0-3] but PIRQ[E-H] maps to [8-11].
+ */
+ irq = pirq < 8 ? pirq + 16 : pirq + 12;
+ }
+
+ return irq;
+}
+#endif
diff --git a/include/configs/qemu-x86.h b/include/configs/qemu-x86.h
index 1b544c1..ac09032 100644
--- a/include/configs/qemu-x86.h
+++ b/include/configs/qemu-x86.h
@@ -15,6 +15,7 @@
#define CONFIG_SYS_MONITOR_LEN (1 << 20)
#define CONFIG_ARCH_MISC_INIT
+#define CONFIG_ARCH_EARLY_INIT_R
#define CONFIG_PCI_MEM_BUS 0xc0000000
#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
@@ -28,6 +29,7 @@
#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS
#define CONFIG_PCI_IO_SIZE 0xe000
+#define CONFIG_SYS_EARLY_PCI_INIT
#define CONFIG_PCI_PNP
#define CONFIG_STD_DEVICES_SETTINGS "stdin=serial,vga\0" \
--
1.8.2.1
More information about the U-Boot
mailing list