[U-Boot] [Patch V8 12/17] armv8/ls1043ardb: Add LS1043ARDB board support
York Sun
yorksun at freescale.com
Fri Nov 6 21:11:24 CET 2015
On 10/26/2015 04:47 AM, Gong Qianyu wrote:
> From: Mingkai Hu <Mingkai.Hu at freescale.com>
>
> LS1043ARDB Specification:
> -------------------------
> Memory subsystem:
> * 2GByte DDR4 SDRAM (32bit bus)
> * 128 Mbyte NOR flash single-chip memory
> * 512 Mbyte NAND flash
> * 16 Mbyte high-speed SPI flash
> * SD connector to interface with the SD memory card
>
> Ethernet:
> * XFI 10G port
> * QSGMII with 4x 1G ports
> * Two RGMII ports
>
> PCIe:
> * PCIe2 (Lanes C) to mini-PCIe slot
> * PCIe3 (Lanes D) to PCIe slot
>
> USB 3.0: two super speed USB 3.0 type A ports
>
> UART: supports two UARTs up to 115200 bps for console
>
> Signed-off-by: Hou Zhiqiang <B48286 at freescale.com>
> Signed-off-by: Li Yang <leoli at freescale.com>
> Signed-off-by: Mingkai Hu <Mingkai.Hu at freescale.com>
> Signed-off-by: York Sun <yorksun at freescale.com>
> Signed-off-by: Gong Qianyu <Qianyu.Gong at freescale.com>
> ---
> V8:
> - No changes.
> V7:
> - No change.
> V6:
> - Move GIC SMMU macros out of ls1043a_common.h.
> V5:
> - No change.
> V4:
> - Change arch to layerscape.
> - Add PCIe support.
> - Move SMMU_BASE, GICC_BASE, GICD_BASE to ls1043a_common.h.
> V3:
> - Fix message typos.
> - Add ddr model number in comments.
> - Fix boot options in README.
> - Remove some dead code.
> V2:
> - Replaced ns_access.h with fsl_csu.h.
>
> arch/arm/Kconfig | 7 +
> arch/arm/cpu/armv8/fsl-layerscape/Makefile | 4 +
> arch/arm/cpu/armv8/fsl-layerscape/ls1043a_serdes.c | 86 ++++++++++
> board/freescale/ls1043ardb/Kconfig | 16 ++
> board/freescale/ls1043ardb/MAINTAINERS | 7 +
> board/freescale/ls1043ardb/Makefile | 9 +
> board/freescale/ls1043ardb/README | 85 +++++++++
> board/freescale/ls1043ardb/cpld.c | 115 +++++++++++++
> board/freescale/ls1043ardb/cpld.h | 43 +++++
> board/freescale/ls1043ardb/ddr.c | 191 +++++++++++++++++++++
> board/freescale/ls1043ardb/ddr.h | 45 +++++
> board/freescale/ls1043ardb/ls1043ardb.c | 131 ++++++++++++++
> configs/ls1043ardb_defconfig | 4 +
> include/configs/ls1043a_common.h | 172 +++++++++++++++++++
> include/configs/ls1043ardb.h | 191 +++++++++++++++++++++
> 15 files changed, 1106 insertions(+)
<snip>
> diff --git a/board/freescale/ls1043ardb/ddr.c b/board/freescale/ls1043ardb/ddr.c
> new file mode 100644
> index 0000000..b181579
> --- /dev/null
> +++ b/board/freescale/ls1043ardb/ddr.c
> @@ -0,0 +1,191 @@
> +/*
> + * Copyright 2015 Freescale Semiconductor, Inc.
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <fsl_ddr_sdram.h>
> +#include <fsl_ddr_dimm_params.h>
> +#include "ddr.h"
> +#ifdef CONFIG_FSL_DEEP_SLEEP
> +#include <fsl_sleep.h>
> +#endif
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +void fsl_ddr_board_options(memctl_options_t *popts,
> + dimm_params_t *pdimm,
> + unsigned int ctrl_num)
> +{
> + const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
> + ulong ddr_freq;
> +
> + if (ctrl_num > 1) {
> + printf("Not supported controller number %d\n", ctrl_num);
> + return;
> + }
> + if (!pdimm->n_ranks)
> + return;
> +
> + pbsp = udimms[0];
> +
> + /* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
> + * freqency and n_banks specified in board_specific_parameters table.
> + */
> + ddr_freq = get_ddr_freq(0) / 1000000;
> + while (pbsp->datarate_mhz_high) {
> + if (pbsp->n_ranks == pdimm->n_ranks) {
> + if (ddr_freq <= pbsp->datarate_mhz_high) {
> + popts->clk_adjust = pbsp->clk_adjust;
> + popts->wrlvl_start = pbsp->wrlvl_start;
> + popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
> + popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
> + popts->cpo_override = pbsp->cpo_override;
> + popts->write_data_delay =
> + pbsp->write_data_delay;
> + goto found;
> + }
> + pbsp_highest = pbsp;
> + }
> + pbsp++;
> + }
> +
> + if (pbsp_highest) {
> + printf("Error: board specific timing not found for %lu MT/s\n",
> + ddr_freq);
> + printf("Trying to use the highest speed (%u) parameters\n",
> + pbsp_highest->datarate_mhz_high);
> + popts->clk_adjust = pbsp_highest->clk_adjust;
> + popts->wrlvl_start = pbsp_highest->wrlvl_start;
> + popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
> + popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
> + } else {
> + panic("DIMM is not supported by this board");
> + }
> +found:
> + debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n",
> + pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb);
> +
> + /* force DDR bus width to 32 bits */
> + popts->data_bus_width = 1;
> + popts->otf_burst_chop_en = 0;
> + popts->burst_length = DDR_BL8;
> +
> + /*
> + * Factors to consider for half-strength driver enable:
> + * - number of DIMMs installed
> + */
> + popts->half_strength_driver_enable = 1;
> + /*
> + * Write leveling override
> + */
> + popts->wrlvl_override = 1;
> + popts->wrlvl_sample = 0xf;
> +
> + /*
> + * Rtt and Rtt_WR override
> + */
> + popts->rtt_override = 0;
> +
> + /* Enable ZQ calibration */
> + popts->zq_en = 1;
> +
> + popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
> + popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
> + DDR_CDR2_VREF_OVRD(70); /* Vref = 70% */
> +}
> +
> +/* DDR model number: MT40A512M8HX-093E */
> +#ifdef CONFIG_SYS_DDR_RAW_TIMING
> +dimm_params_t ddr_raw_timing = {
> + .n_ranks = 1,
> + .rank_density = 2147483648u,
> + .capacity = 2147483648u,
> + .primary_sdram_width = 32,
> + .ec_sdram_width = 0,
> + .registered_dimm = 0,
> + .mirrored_dimm = 0,
> + .n_row_addr = 15,
> + .n_col_addr = 10,
> + .bank_addr_bits = 0,
> + .bank_group_bits = 2,
> + .edc_config = 0,
> + .burst_lengths_bitmask = 0x0c,
> +
> + .tckmin_x_ps = 938,
> + .tckmax_ps = 1500,
> + .caslat_x = 0x000DFA00,
> + .taa_ps = 13500,
> + .trcd_ps = 13500,
> + .trp_ps = 13500,
> + .tras_ps = 33000,
> + .trc_ps = 46500,
> + .trfc1_ps = 260000,
> + .trfc2_ps = 160000,
> + .trfc4_ps = 110000,
> + .tfaw_ps = 21000,
> + .trrds_ps = 3700,
> + .trrdl_ps = 5300,
> + .tccdl_ps = 5355,
> + .refresh_rate_ps = 7800000,
> + .dq_mapping[0] = 0x0,
> + .dq_mapping[1] = 0x0,
> + .dq_mapping[2] = 0x0,
> + .dq_mapping[3] = 0x0,
> + .dq_mapping[4] = 0x0,
> + .dq_mapping[5] = 0x0,
> + .dq_mapping[6] = 0x0,
> + .dq_mapping[7] = 0x0,
> + .dq_mapping[8] = 0x0,
> + .dq_mapping[9] = 0x0,
> + .dq_mapping[10] = 0x0,
> + .dq_mapping[11] = 0x0,
> + .dq_mapping[12] = 0x0,
> + .dq_mapping[13] = 0x0,
> + .dq_mapping[14] = 0x0,
> + .dq_mapping[15] = 0x0,
> + .dq_mapping[16] = 0x0,
> + .dq_mapping[17] = 0x0,
> + .dq_mapping_ors = 0,
> +};
> +
> +int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
> + unsigned int controller_number,
> + unsigned int dimm_number)
> +{
> + static const char dimm_model[] = "Fixed DDR on board";
> +
> + if (((controller_number == 0) && (dimm_number == 0)) ||
> + ((controller_number == 1) && (dimm_number == 0))) {
> + memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t));
> + memset(pdimm->mpart, 0, sizeof(pdimm->mpart));
> + memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1);
> + }
> +
> + return 0;
> +}
> +#endif
> +
> +phys_size_t initdram(int board_type)
> +{
> + phys_size_t dram_size;
> +
> +#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_SPL)
> + puts("Initializing DDR....\n");
> + dram_size = fsl_ddr_sdram();
> +#else
> + dram_size = fsl_ddr_sdram_size();
> +#endif
> +#ifdef CONFIG_FSL_DEEP_SLEEP
> + fsl_dp_ddr_restore();
> +#endif
> +
> + return dram_size;
> +}
> +
> +void dram_init_banksize(void)
> +{
> + gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
> + gd->bd->bi_dram[0].size = gd->ram_size;
> +}
Mingkai,
There is an issue with this function. If you have large memory, you will have
more than one bank, won't you?
York
More information about the U-Boot
mailing list