[U-Boot] [PATCH 03/10] sunxi: power: axp818: add support for axp818 driver
Hans de Goede
hdegoede at redhat.com
Fri Nov 13 18:21:34 CET 2015
Hi,
On 12-11-15 19:09, Vishnu Patekar wrote:
> AXP818 is rsb based PMIC and used on Allwinner A83T H8 Homlet dev board.
> It's registers are different and calculating reg config is different than
> that of earlier axp power ICs.
>
> DCDC1, DCDC2, DCDC3 and DCDC5 is implemented at the moment.
> all other voltages can be added subsequently.
> AXP datasheet is uploaded to wiki:
> http://linux-sunxi.org/File:AXP818_datasheet_Revision1.0.pdf
>
> Signed-off-by: Vishnu Patekar <vishnupatekar0510 at gmail.com>
> ---
> drivers/power/Kconfig | 34 ++++++++-----
> drivers/power/Makefile | 1 +
> drivers/power/axp818.c | 132 +++++++++++++++++++++++++++++++++++++++++++++++++
> include/axp818.h | 75 ++++++++++++++++++++++++++++
> include/axp_pmic.h | 3 ++
> 5 files changed, 234 insertions(+), 11 deletions(-)
> create mode 100644 drivers/power/axp818.c
> create mode 100644 include/axp818.h
>
> diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig
> index 809f8f1..d2494d4 100644
> --- a/drivers/power/Kconfig
> +++ b/drivers/power/Kconfig
> @@ -8,7 +8,8 @@ choice
> prompt "Select Sunxi PMIC Variant"
> depends on ARCH_SUNXI
> default AXP209_POWER if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
> - default AXP221_POWER if MACH_SUN6I || MACH_SUN8I
> + default AXP221_POWER if MACH_SUN6I || MACH_SUN8I && !MACH_SUN8I_A83T
This will become unmanagable once we also get support for the H3 please change this to:
default AXP221_POWER if MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33
> + default AXP818_POWER if MACH_SUN8I_A83T
>
> config SUNXI_NO_PMIC
> boolean "board without a pmic"
> @@ -31,16 +32,24 @@ config AXP209_POWER
>
> config AXP221_POWER
> boolean "axp221 / axp223 pmic support"
> - depends on MACH_SUN6I || MACH_SUN8I
> + depends on MACH_SUN6I || MACH_SUN8I || !MACH_SUN8I_A83T
Idem.
> ---help---
> Select this to enable support for the axp221/axp223 pmic found on most
> A23 and A31 boards.
>
> +config AXP818_POWER
> + boolean "axp818 pmic support"
> + depends on MACH_SUN8I_A83T
> + ---help---
> + Say y here to enable support for the axp818 pmic found on
> + A83T dev board.
> +
> endchoice
>
> config AXP_DCDC1_VOLT
> int "axp pmic dcdc1 voltage"
> - depends on AXP221_POWER
> + depends on AXP221_POWER || AXP818_POWER
> + default 3300 if AXP818_POWER
> default 3000 if MACH_SUN6I || MACH_SUN8I
> ---help---
> Set the voltage (mV) to program the axp pmic dcdc1 at, set to 0 to
Please add a comment to the --help-- what this voltage is used for (assuming
that you know). The same goes for all the other voltage settings, otherwise
this patch looks good.
Regards,
Hans
> @@ -51,7 +60,8 @@ config AXP_DCDC1_VOLT
>
> config AXP_DCDC2_VOLT
> int "axp pmic dcdc2 voltage"
> - depends on AXP152_POWER || AXP209_POWER || AXP221_POWER
> + depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP818_POWER
> + default 900 if AXP818_POWER
> default 1400 if AXP152_POWER || AXP209_POWER
> default 1200 if MACH_SUN6I
> default 1100 if MACH_SUN8I
> @@ -64,7 +74,8 @@ config AXP_DCDC2_VOLT
>
> config AXP_DCDC3_VOLT
> int "axp pmic dcdc3 voltage"
> - depends on AXP152_POWER || AXP209_POWER || AXP221_POWER
> + depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP818_POWER
> + default 900 if AXP818_POWER
> default 1500 if AXP152_POWER
> default 1250 if AXP209_POWER
> default 1200 if MACH_SUN6I || MACH_SUN8I
> @@ -78,7 +89,7 @@ config AXP_DCDC3_VOLT
>
> config AXP_DCDC4_VOLT
> int "axp pmic dcdc4 voltage"
> - depends on AXP152_POWER || AXP221_POWER
> + depends on AXP152_POWER || AXP221_POWER || AXP818_POWER
> default 1250 if AXP152_POWER
> default 1200 if MACH_SUN6I
> default 0 if MACH_SUN8I
> @@ -91,7 +102,8 @@ config AXP_DCDC4_VOLT
>
> config AXP_DCDC5_VOLT
> int "axp pmic dcdc5 voltage"
> - depends on AXP221_POWER
> + depends on AXP221_POWER || AXP818_POWER
> + default 1800 if AXP818_POWER
> default 1500 if MACH_SUN6I || MACH_SUN8I
> ---help---
> Set the voltage (mV) to program the axp pmic dcdc5 at, set to 0 to
> @@ -111,7 +123,7 @@ config AXP_ALDO1_VOLT
>
> config AXP_ALDO2_VOLT
> int "axp pmic (a)ldo2 voltage"
> - depends on AXP152_POWER || AXP209_POWER || AXP221_POWER
> + depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP818_POWER
> default 3000 if AXP152_POWER || AXP209_POWER
> default 0 if MACH_SUN6I
> default 2500 if MACH_SUN8I
> @@ -125,8 +137,8 @@ config AXP_ALDO2_VOLT
>
> config AXP_ALDO3_VOLT
> int "axp pmic (a)ldo3 voltage"
> - depends on AXP209_POWER || AXP221_POWER
> - default 0 if AXP209_POWER
> + depends on AXP209_POWER || AXP221_POWER || AXP818_POWER
> + default 0 if AXP209_POWER || AXP818_POWER
> default 3000 if MACH_SUN6I || MACH_SUN8I
> ---help---
> Set the voltage (mV) to program the axp pmic aldo3 at, set to 0 to
> @@ -171,7 +183,7 @@ config AXP_DLDO3_VOLT
>
> config AXP_DLDO4_VOLT
> int "axp pmic dldo4 voltage"
> - depends on AXP221_POWER
> + depends on AXP221_POWER || AXP818_POWER
> default 0
> ---help---
> Set the voltage (mV) to program the axp pmic dldo4 at, set to 0 to
> diff --git a/drivers/power/Makefile b/drivers/power/Makefile
> index a2d3c04..0fdbca3 100644
> --- a/drivers/power/Makefile
> +++ b/drivers/power/Makefile
> @@ -9,6 +9,7 @@ obj-$(CONFIG_AS3722_POWER) += as3722.o
> obj-$(CONFIG_AXP152_POWER) += axp152.o
> obj-$(CONFIG_AXP209_POWER) += axp209.o
> obj-$(CONFIG_AXP221_POWER) += axp221.o
> +obj-$(CONFIG_AXP818_POWER) += axp818.o
> obj-$(CONFIG_EXYNOS_TMU) += exynos-tmu.o
> obj-$(CONFIG_FTPMU010_POWER) += ftpmu010.o
> obj-$(CONFIG_TPS6586X_POWER) += tps6586x.o
> diff --git a/drivers/power/axp818.c b/drivers/power/axp818.c
> new file mode 100644
> index 0000000..4b21a83
> --- /dev/null
> +++ b/drivers/power/axp818.c
> @@ -0,0 +1,132 @@
> +/*
> + * AXP818 driver based on AXP221 driver
> + *
> + *
> + * (C) Copyright 2015 Vishnu Patekar <vishnuptekar0510 at gmail.com>
> + *
> + * Based on axp221.c
> + * (C) Copyright 2014 Hans de Goede <hdegoede at redhat.com>
> + * (C) Copyright 2013 Oliver Schinagl <oliver at schinagl.nl>
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <errno.h>
> +#include <asm/arch/gpio.h>
> +#include <asm/arch/pmic_bus.h>
> +#include <axp_pmic.h>
> +
> +static u8 axp818_mvolt_to_cfg(int mvolt, int min, int max, int div)
> +{
> + if (mvolt < min)
> + mvolt = min;
> + else if (mvolt > max)
> + mvolt = max;
> +
> + return (mvolt - min) / div;
> +}
> +
> +int axp_set_dcdc1(unsigned int mvolt)
> +{
> + int ret;
> + u8 cfg = axp818_mvolt_to_cfg(mvolt, 1600, 3400, 100);
> +
> + if (mvolt == 0)
> + return pmic_bus_clrbits(AXP818_OUTPUT_CTRL1,
> + AXP818_OUTPUT_CTRL1_DCDC1_EN);
> +
> + ret = pmic_bus_write(AXP818_DCDC1_CTRL, cfg);
> + if (ret)
> + return ret;
> +
> + return pmic_bus_setbits(AXP818_OUTPUT_CTRL1,
> + AXP818_OUTPUT_CTRL1_DCDC1_EN);
> +}
> +
> +int axp_set_dcdc2(unsigned int mvolt)
> +{
> + int ret;
> + u8 cfg;
> +
> + if (mvolt >= 1220)
> + cfg = 70 + axp818_mvolt_to_cfg(mvolt, 1220, 1300, 20);
> + else
> + cfg = axp818_mvolt_to_cfg(mvolt, 500, 1200, 10);
> +
> + if (mvolt == 0)
> + return pmic_bus_clrbits(AXP818_OUTPUT_CTRL1,
> + AXP818_OUTPUT_CTRL1_DCDC2_EN);
> +
> + ret = pmic_bus_write(AXP818_DCDC2_CTRL, cfg);
> + if (ret)
> + return ret;
> +
> + return pmic_bus_setbits(AXP818_OUTPUT_CTRL1,
> + AXP818_OUTPUT_CTRL1_DCDC2_EN);
> +}
> +
> +int axp_set_dcdc3(unsigned int mvolt)
> +{
> + int ret;
> + u8 cfg;
> +
> + if (mvolt >= 1220)
> + cfg = 70 + axp818_mvolt_to_cfg(mvolt, 1220, 1300, 20);
> + else
> + cfg = axp818_mvolt_to_cfg(mvolt, 500, 1200, 10);
> +
> + if (mvolt == 0)
> + return pmic_bus_clrbits(AXP818_OUTPUT_CTRL1,
> + AXP818_OUTPUT_CTRL1_DCDC3_EN);
> +
> + ret = pmic_bus_write(AXP818_DCDC3_CTRL, cfg);
> + if (ret)
> + return ret;
> +
> + return pmic_bus_setbits(AXP818_OUTPUT_CTRL1,
> + AXP818_OUTPUT_CTRL1_DCDC3_EN);
> +}
> +
> +int axp_set_dcdc5(unsigned int mvolt)
> +{
> + int ret;
> + u8 cfg;
> +
> + if (mvolt >= 1140)
> + cfg = 32 + axp818_mvolt_to_cfg(mvolt, 1140, 1840, 20);
> + else
> + cfg = axp818_mvolt_to_cfg(mvolt, 800, 1120, 10);
> +
> + if (mvolt == 0)
> + return pmic_bus_clrbits(AXP818_OUTPUT_CTRL1,
> + AXP818_OUTPUT_CTRL1_DCDC5_EN);
> +
> + ret = pmic_bus_write(AXP818_DCDC5_CTRL, cfg);
> + if (ret)
> + return ret;
> +
> + return pmic_bus_setbits(AXP818_OUTPUT_CTRL1,
> + AXP818_OUTPUT_CTRL1_DCDC5_EN);
> +}
> +
> +int axp_init(void)
> +{
> + u8 axp_chip_id;
> + int ret;
> +
> + ret = pmic_bus_init();
> + if (ret)
> + return ret;
> +
> + ret = pmic_bus_read(AXP818_CHIP_ID, &axp_chip_id);
> + if (ret)
> + return ret;
> +
> + if (!(axp_chip_id == 0x51))
> + return -ENODEV;
> + else
> + return ret;
> +
> + return 0;
> +}
> diff --git a/include/axp818.h b/include/axp818.h
> new file mode 100644
> index 0000000..1dc6456
> --- /dev/null
> +++ b/include/axp818.h
> @@ -0,0 +1,75 @@
> +/*
> + * (C) Copyright 2015 Vishnu Patekar <vishnupatekar0510 at gmail.com>
> + *
> + * X-Powers AXP818 Power Management IC driver
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#define AXP818_CHIP_ID 0x03
> +
> +#define AXP818_OUTPUT_CTRL1 0x10
> +#define AXP818_OUTPUT_CTRL1_DCDC1_EN (1 << 0)
> +#define AXP818_OUTPUT_CTRL1_DCDC2_EN (1 << 1)
> +#define AXP818_OUTPUT_CTRL1_DCDC3_EN (1 << 2)
> +#define AXP818_OUTPUT_CTRL1_DCDC4_EN (1 << 3)
> +#define AXP818_OUTPUT_CTRL1_DCDC5_EN (1 << 4)
> +#define AXP818_OUTPUT_CTRL1_DCDC6_EN (1 << 5)
> +#define AXP818_OUTPUT_CTRL1_DCDC7_EN (1 << 6)
> +#define AXP818_OUTPUT_CTRL2 0x12
> +#define AXP818_OUTPUT_CTRL2_ELDO1_EN (1 << 0)
> +#define AXP818_OUTPUT_CTRL2_ELDO2_EN (1 << 1)
> +#define AXP818_OUTPUT_CTRL2_ELDO3_EN (1 << 2)
> +#define AXP818_OUTPUT_CTRL2_DLDO1_EN (1 << 3)
> +#define AXP818_OUTPUT_CTRL2_DLDO2_EN (1 << 4)
> +#define AXP818_OUTPUT_CTRL2_DLDO3_EN (1 << 5)
> +#define AXP818_OUTPUT_CTRL2_DLDO4_EN (1 << 6)
> +#define AXP818_OUTPUT_CTRL3 0x13
> +#define AXP818_OUTPUT_CTRL3_FLDO1_EN (1 << 2)
> +#define AXP818_OUTPUT_CTRL3_FLDO2_EN (1 << 3)
> +#define AXP818_OUTPUT_CTRL3_FLDO3_EN (1 << 4)
> +#define AXP818_OUTPUT_CTRL3_ALDO1_EN (1 << 5)
> +#define AXP818_OUTPUT_CTRL3_ALDO2_EN (1 << 6)
> +#define AXP818_OUTPUT_CTRL3_ALDO3_EN (1 << 7)
> +
> +#define AXP818_DCDC1_CTRL 0x20
> +#define AXP818_DCDC2_CTRL 0x21
> +#define AXP818_DCDC3_CTRL 0x22
> +#define AXP818_DCDC4_CTRL 0x23
> +#define AXP818_DCDC5_CTRL 0x24
> +#define AXP818_DCDC6_CTRL 0x25
> +
> +#define AXP818_DLDO1_CTRL 0x15
> +#define AXP818_DLDO2_CTRL 0x16
> +#define AXP818_DLDO3_CTRL 0x17
> +#define AXP818_DLDO4_CTRL 0x18
> +#define AXP818_ELDO1_CTRL 0x19
> +#define AXP818_ELDO2_CTRL 0x1a
> +#define AXP818_ELDO3_CTRL 0x1b
> +#define AXP818_ELDO3_CTRL 0x1b
> +#define AXP818_FLDO1_CTRL 0x1c
> +#define AXP818_FLDO2_3_CTRL 0x1d
> +#define AXP818_DCDC1_CTRL 0x20
> +#define AXP818_DCDC2_CTRL 0x21
> +#define AXP818_DCDC3_CTRL 0x22
> +#define AXP818_DCDC4_CTRL 0x23
> +#define AXP818_DCDC5_CTRL 0x24
> +#define AXP818_DCDC6_CTRL 0x25
> +#define AXP818_DCDC7_CTRL 0x26
> +
> +#define AXP818_ALDO1_CTRL 0x28
> +#define AXP818_ALDO2_CTRL 0x29
> +#define AXP818_ALDO3_CTRL 0x2a
> +
> +int axp818_init(void);
> +
> +/* For axp_gpio.c */
> +#define AXP_POWER_STATUS 0x00
> +#define AXP_POWER_STATUS_VBUS_PRESENT (1 << 5)
> +#define AXP_GPIO0_CTRL 0x90
> +#define AXP_GPIO1_CTRL 0x92
> +#define AXP_GPIO_CTRL_OUTPUT_LOW 0x00 /* Drive pin low */
> +#define AXP_GPIO_CTRL_OUTPUT_HIGH 0x01 /* Drive pin high */
> +#define AXP_GPIO_CTRL_INPUT 0x02 /* Input */
> +#define AXP_GPIO_STATE 0x94
> +#define AXP_GPIO_STATE_OFFSET 0
> diff --git a/include/axp_pmic.h b/include/axp_pmic.h
> index ef339c4..3b01c49 100644
> --- a/include/axp_pmic.h
> +++ b/include/axp_pmic.h
> @@ -16,6 +16,9 @@
> #ifdef CONFIG_AXP221_POWER
> #include <axp221.h>
> #endif
> +#ifdef CONFIG_AXP818_POWER
> +#include <axp818.h>
> +#endif
>
> int axp_set_dcdc1(unsigned int mvolt);
> int axp_set_dcdc2(unsigned int mvolt);
>
More information about the U-Boot
mailing list