[U-Boot] [PATCH v5] colibri_vf: Add board_usb_phy_mode function

[maitysanchayan at gmail.com]

Hello,

Ping?

Any further feedback? Is the patchset good to get accepted?

Thanks.

Regards,
Sanchayan.

On 15-11-12 11:47:35, Sanchayan Maity wrote:
> Add board_usb_phy_mode function for detecting whether a port is
> being used as host or client using a GPIO. On Colibri Vybrid we
> provide GPIO 102 for this very same purpose.
> 
> Signed-off-by: Sanchayan Maity <maitysanchayan at gmail.com>
> ---
> Changes since v4:
> No need to break after return.
> 
> Changes since v3:
> Return USB_INIT_DEVICE or USB_INIT_HOST after checking for
> the GPIO state to account for the fact that the previous
> logic breaks in case if the enum for USB mode were to ever
> be changed.
> 
> Add comments based on Stefan's feedback.
> 
> Changes since v2:
> 
> Instead of returning 0 from board_usb_phy_mode return it as
> USB_INIT_HOST.
> 
> Changes since v1:
> 
> Move the GPIO request call to the board_init function as all
> further calls to board_usb_phy_mode will actually result in the
> gpio_request failing.
> ---
>  board/toradex/colibri_vf/colibri_vf.c | 33 ++++++++++++++++++++++++++++++++-
>  1 file changed, 32 insertions(+), 1 deletion(-)
> 
> diff --git a/board/toradex/colibri_vf/colibri_vf.c b/board/toradex/colibri_vf/colibri_vf.c
> index a6d1c5b..c65ccb3 100644
> --- a/board/toradex/colibri_vf/colibri_vf.c
> +++ b/board/toradex/colibri_vf/colibri_vf.c
> @@ -21,6 +21,7 @@
>  #include <i2c.h>
>  #include <g_dnl.h>
>  #include <asm/gpio.h>
> +#include <usb.h>
>  
>  DECLARE_GLOBAL_DATA_PTR;
>  
> @@ -34,6 +35,7 @@ DECLARE_GLOBAL_DATA_PTR;
>  			PAD_CTL_DSE_50ohm | PAD_CTL_OBE_IBE_ENABLE)
>  
>  #define USB_PEN_GPIO           83
> +#define USB_CDET_GPIO		102
>  
>  static struct ddrmc_cr_setting colibri_vf_cr_settings[] = {
>  	/* levelling */
> @@ -92,6 +94,7 @@ static struct ddrmc_cr_setting colibri_vf_cr_settings[] = {
>  
>  static const iomux_v3_cfg_t usb_pads[] = {
>  	VF610_PAD_PTD4__GPIO_83,
> +	VF610_PAD_PTC29__GPIO_102,
>  };
>  
>  int dram_init(void)
> @@ -280,7 +283,6 @@ static void setup_iomux_gpio(void)
>  		VF610_PAD_PTB23__GPIO_93,
>  		VF610_PAD_PTB26__GPIO_96,
>  		VF610_PAD_PTB28__GPIO_98,
> -		VF610_PAD_PTC29__GPIO_102,
>  		VF610_PAD_PTC30__GPIO_103,
>  		VF610_PAD_PTA7__GPIO_134,
>  	};
> @@ -509,6 +511,10 @@ int board_init(void)
>  
>  	setbits_le32(&scsc->sosc_ctr, SCSC_SOSC_CTR_SOSC_EN);
>  
> +#ifdef CONFIG_USB_EHCI_VF
> +	gpio_request(USB_CDET_GPIO, "usb-cdet-gpio");
> +#endif
> +
>  	return 0;
>  }
>  
> @@ -554,4 +560,29 @@ int board_ehci_hcd_init(int port)
>  	}
>  	return 0;
>  }
> +
> +int board_usb_phy_mode(int port)
> +{
> +	switch (port) {
> +	case 0:
> +		/*
> +		 * Port 0 is used only in client mode on Colibri Vybrid modules
> +		 * Check for state of USB client gpio pin and accordingly return
> +		 * USB_INIT_DEVICE or USB_INIT_HOST.
> +		 */
> +		if (gpio_get_value(USB_CDET_GPIO))
> +			return USB_INIT_DEVICE;
> +		else
> +			return USB_INIT_HOST;
> +	case 1:
> +		/* Port 1 is used only in host mode on Colibri Vybrid modules */
> +		return USB_INIT_HOST;
> +	default:
> +		/*
> +		 * There are only two USB controllers on Vybrid. Ideally we will
> +		 * not reach here. However return USB_INIT_HOST if we do.
> +		 */
> +		return USB_INIT_HOST;
> +	}
> +}
>  #endif
> -- 
> 2.6.2
>