[U-Boot] [PATCH 2/3] arm: at91/spl: mpddrc: add mpddrc DDR3-SDRAM initialization
Andreas Bießmann
andreas.devel at googlemail.com
Fri Nov 27 22:36:30 CET 2015
Hi Wenyou,
On 04.11.15 07:32, Wenyou Yang wrote:
> The implementation conforms to DDR3-SRAM/DDR3L-SDRAM
typo ----------------------------------^
> initialization section described in the SAMA5D2 datasheet.
>
> Add registers and definitions of mpddrc controller, which is used
> to support DDR3 devices.
>
> Signed-off-by: Wenyou Yang <wenyou.yang at atmel.com>
> ---
>
> arch/arm/mach-at91/include/mach/atmel_mpddrc.h | 88 +++++++++++++++++++++---
> arch/arm/mach-at91/mpddrc.c | 87 +++++++++++++++++++++++
> 2 files changed, 167 insertions(+), 8 deletions(-)
>
> diff --git a/arch/arm/mach-at91/include/mach/atmel_mpddrc.h b/arch/arm/mach-at91/include/mach/atmel_mpddrc.h
> index 47b4cd4..e777e67 100644
> --- a/arch/arm/mach-at91/include/mach/atmel_mpddrc.h
> +++ b/arch/arm/mach-at91/include/mach/atmel_mpddrc.h
> @@ -2,6 +2,9 @@
> * Copyright (C) 2013 Atmel Corporation
> * Bo Shen <voice.shen at atmel.com>
> *
> + * Copyright (C) 2015 Atmel Corporation
> + * Wenyou Yang <wenyou.yang at atmel.com>
> + *
> * SPDX-License-Identifier: GPL-2.0+
> */
>
> @@ -23,14 +26,38 @@ struct atmel_mpddrc_config {
> * If other register needed, will add them later
This comment should be removed
> */
> struct atmel_mpddr {
> - u32 mr;
> - u32 rtr;
> - u32 cr;
> - u32 tpr0;
> - u32 tpr1;
> - u32 tpr2;
> - u32 reserved[2];
> - u32 md;
> + u32 mr; /* 0x00: Mode Register */
> + u32 rtr; /* 0x04: Refresh Timer Register */
> + u32 cr; /* 0x08: Configuration Register */
> + u32 tpr0; /* 0x0c: Timing Parameter 0 Register */
> + u32 tpr1; /* 0x10: Timing Parameter 1 Register */
> + u32 tpr2; /* 0x14: Timing Parameter 2 Register */
> + u32 reserved; /* 0x18: Reserved */
> + u32 lpr; /* 0x1c: Low-power Register */
> + u32 md; /* 0x20: Memory Device Register */
> + u32 reserved1; /* 0x24: Reserved */
This is the MPDDRC High Speed Register for sama5d3
> + u32 lpddr23_lpr; /* 0x28: LPDDR2-LPDDR3 Low-power Register*/
> + u32 cal_mr4; /* 0x2c: LPDDR2 LPDDR3 and DDR3 Calibration and MR4 Register */
> + u32 tim_cal; /* 0x30: LPDDR2 LPDDR3 and DDR3 Timing Calibration Register */
> + u32 io_calibr; /* 0x34: IO Calibration */
> + u32 ocms; /* 0x38: OCMS Register */
> + u32 ocms_key1; /* 0x3c: OCMS KEY1 Register */
> + u32 ocms_key2; /* 0x40: OCMS KEY2 Register */
> + u32 conf_arbiter; /* 0x44: Configuration Arbiter Register */
> + u32 timeout; /* 0x48: Timeout Port 0/1/2/3 Register */
> + u32 req_port0123; /* 0x4c: Request Port 0/1/2/3 Register */
> + u32 req_port4567; /* 0x50: Request Port 4/5/6/7 Register */
> + u32 bdw_port0123; /* 0x54: Bandwidth Port 0/1/2/3 Register */
> + u32 bdw_port4567; /* 0x58: Bandwidth Port 4/5/6/7 Register */
> + u32 rd_data_path; /* 0x5c: Read Datapath Register */
> + u32 mcfgr; /* 0x60: Monitor Configuration */
> + u32 maddr[8]; /* 0x64 ~ 0x80: Monitor Address High/Low port0~7 */
> + u32 minfo[8]; /* 0x84 ~ 0xa0: Monitor Information port0~7 */
... here it seems the two variants (sama5d3 and sama5d2) are way different
> + u32 reserved2[16];
> + u32 wpmr; /* 0xe4: Write Protection Mode Register */
> + u32 wpsr; /* 0xe8: Write Protection Status Register */
> + u32 reserved3[4];
> + u32 version; /* 0xfc: IP version */
> };
>
>
> @@ -38,6 +65,9 @@ int ddr2_init(const unsigned int base,
> const unsigned int ram_address,
> const struct atmel_mpddrc_config *mpddr_value);
>
> +int ddr3_init(const unsigned int ram_address,
> + const struct atmel_mpddrc_config *mpddr_value);
> +
> /* Bit field in mode register */
> #define ATMEL_MPDDRC_MR_MODE_NORMAL_CMD 0x0
> #define ATMEL_MPDDRC_MR_MODE_NOP_CMD 0x1
> @@ -120,9 +150,51 @@ int ddr2_init(const unsigned int base,
>
> /* Bit field in Memory Device Register */
> #define ATMEL_MPDDRC_MD_LPDDR_SDRAM 0x3
> +#define ATMEL_MPDDRC_MD_DDR3_SDRAM 0x4
> +#define ATMEL_MPDDRC_MD_LPDDR3_SDRAM 0x5
> #define ATMEL_MPDDRC_MD_DDR2_SDRAM 0x6
> #define ATMEL_MPDDRC_MD_DBW_MASK (0x1 << 4)
> #define ATMEL_MPDDRC_MD_DBW_32_BITS (0x0 << 4)
> #define ATMEL_MPDDRC_MD_DBW_16_BITS (0x1 << 4)
>
> +/* Bit field in I/O Calibration Register */
> +#define ATMEL_MPDDRC_IO_CALIBR_RDIV 0x7
> +
> +#define ATMEL_MPDDRC_IO_CALIBR_LPDDR2_RZQ_34_3 0x1
> +#define ATMEL_MPDDRC_IO_CALIBR_LPDDR2_RZQ_40 0x2
> +#define ATMEL_MPDDRC_IO_CALIBR_LPDDR2_RZQ_48 0x3
> +#define ATMEL_MPDDRC_IO_CALIBR_LPDDR2_RZQ_60 0x4
> +#define ATMEL_MPDDRC_IO_CALIBR_LPDDR2_RZQ_80 0x6
> +#define ATMEL_MPDDRC_IO_CALIBR_LPDDR2_RZQ_120 0x7
> +
> +#define ATMEL_MPDDRC_IO_CALIBR_DDR2_RZQ_35 0x2
> +#define ATMEL_MPDDRC_IO_CALIBR_DDR2_RZQ_43 0x3
> +#define ATMEL_MPDDRC_IO_CALIBR_DDR2_RZQ_52 0x4
> +#define ATMEL_MPDDRC_IO_CALIBR_DDR2_RZQ_70 0x6
> +#define ATMEL_MPDDRC_IO_CALIBR_DDR2_RZQ_105 0x7
> +
> +#define ATMEL_MPDDRC_IO_CALIBR_DDR3_RZQ_37 0x2
> +#define ATMEL_MPDDRC_IO_CALIBR_DDR3_RZQ_44 0x3
> +#define ATMEL_MPDDRC_IO_CALIBR_DDR3_RZQ_55 0x4
> +#define ATMEL_MPDDRC_IO_CALIBR_DDR3_RZQ_73 0x6
> +#define ATMEL_MPDDRC_IO_CALIBR_DDR3_RZQ_110 0x7
> +
> +#define ATMEL_MPDDRC_IO_CALIBR_DDR3_RZQ_37 0x2
> +#define ATMEL_MPDDRC_IO_CALIBR_DDR3_RZQ_44 0x3
> +#define ATMEL_MPDDRC_IO_CALIBR_DDR3_RZQ_55 0x4
> +#define ATMEL_MPDDRC_IO_CALIBR_DDR3_RZQ_73 0x6
> +#define ATMEL_MPDDRC_IO_CALIBR_DDR3_RZQ_110 0x7
> +
> +#define ATMEL_MPDDRC_IO_CALIBR_TZQIO 0x7f
> +#define ATMEL_MPDDRC_IO_CALIBR_TZQIO_(x) (((x) & 0x7f) << 8)
> +
> +#define ATMEL_MPDDRC_IO_CALIBR_EN_CALIB (0x1 << 4)
> +
> +/* Bit field in Read Data Path Register */
> +#define ATMEL_MPDDRC_RD_DATA_PATH_SHIFT_SAMPLING 0x3
> +#define ATMEL_MPDDRC_RD_DATA_PATH_NO_SHIFT 0x0
> +#define ATMEL_MPDDRC_RD_DATA_PATH_SHIFT_ONE_CYCLE 0x1
> +#define ATMEL_MPDDRC_RD_DATA_PATH_SHIFT_TWO_CYCLE 0x2
> +#define ATMEL_MPDDRC_RD_DATA_PATH_SHIFT_THREE_CYCLE 0x3
> +
> #endif
> diff --git a/arch/arm/mach-at91/mpddrc.c b/arch/arm/mach-at91/mpddrc.c
> index 9ba2a00..ae8b0ff 100644
> --- a/arch/arm/mach-at91/mpddrc.c
> +++ b/arch/arm/mach-at91/mpddrc.c
> @@ -2,6 +2,9 @@
> * Copyright (C) 2013 Atmel Corporation
> * Bo Shen <voice.shen at atmel.com>
> *
> + * Copyright (C) 2015 Atmel Corporation
> + * Wenyou Yang <wenyou.yang at atmel.com>
> + *
> * SPDX-License-Identifier: GPL-2.0+
> */
>
> @@ -135,3 +138,87 @@ int ddr2_init(const unsigned int base,
>
> return 0;
> }
> +
> +int ddr3_init(const unsigned int ram_address,
> + const struct atmel_mpddrc_config *mpddr_value)
> +{
> + struct atmel_mpddr *mpddr = (struct atmel_mpddr *)ATMEL_BASE_MPDDRC;
> + u32 ba_off;
> +
> + /* Compute bank offset according to NC in configuration register */
> + ba_off = (mpddr_value->cr & ATMEL_MPDDRC_CR_NC_MASK) + 9;
> + if (ddr2_decodtype_is_seq(mpddr_value->cr))
> + ba_off += ((mpddr_value->cr & ATMEL_MPDDRC_CR_NR_MASK) >> 2) + 11;
> +
> + ba_off += (mpddr_value->md & ATMEL_MPDDRC_MD_DBW_MASK) ? 1 : 2;
> +
> + /* Program the memory device type */
> + writel(mpddr_value->md, &mpddr->md);
> +
> + /*
> + * Program features of the DDR3-SDRAM device and timing parameters
> + */
> + writel(mpddr_value->cr, &mpddr->cr);
> +
> + writel(mpddr_value->tpr0, &mpddr->tpr0);
> + writel(mpddr_value->tpr1, &mpddr->tpr1);
> + writel(mpddr_value->tpr2, &mpddr->tpr2);
> +
> + /* A NOP command is issued to the DDR3-SRAM */
> + atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_NOP_CMD, ram_address);
> +
> + /* A pause of at least 500us must be observed before a single toggle. */
> + udelay(500);
whitespace error
> +
> + /* A NOP command is issued to the DDR3-SDRAM */
> + atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_NOP_CMD, ram_address);
> +
> + /*
> + * An Extended Mode Register Set (EMRS2) cycle is issued to choose
> + * between commercial or high temperature operations.
> + */
> + atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_EXT_LMR_CMD,
> + ram_address + (0x2 << ba_off));
> + /*
> + * Step 7: An Extended Mode Register Set (EMRS3) cycle is issued to set
> + * the Extended Mode Register to 0.
> + */
> + atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_EXT_LMR_CMD,
> + ram_address + (0x3 << ba_off));
> + /*
> + * An Extended Mode Register Set (EMRS1) cycle is issued to disable and
> + * to program O.D.S. (Output Driver Strength).
> + */
> + atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_EXT_LMR_CMD,
> + ram_address + (0x1 << ba_off));
> +
> + /*
> + * Write a one to the DLL bit (enable DLL reset) in the MPDDRC
> + * Configuration Register.
> + */
> +
> + /* A Mode Register Set (MRS) cycle is issued to reset DLL. */
> + atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_LMR_CMD, ram_address);
> +
> + udelay(50);
> +
> + /*
> + * A Calibration command (MRS) is issued to calibrate RTT and RON
> + * values for the Process Voltage Temperature (PVT).
> + */
> + atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_DEEP_CMD, ram_address);
> +
> + /* A Normal Mode command is provided. */
> + atmel_mpddr_op(mpddr, ATMEL_MPDDRC_MR_MODE_NORMAL_CMD, ram_address);
> +
> + /* Perform a write access to any DDR3-SDRAM address. */
> + writel(0, ram_address);
> +
> + /*
> + * Write the refresh rate into the COUNT field in the MPDDRC
> + * Refresh Timer Register (MPDDRC_RTR):
> + */
> + writel(mpddr_value->rtr, &mpddr->rtr);
> +
> + return 0;
> +}
>
Sequence seems to be good to me
Andreas
More information about the U-Boot
mailing list