[U-Boot] [PATCH v2] arm: vf610twr: improve memory layout

[Stefan Agner]

Currently, the device tree relocation is disabled, likely to
keep some DDR3 RAM at the end for Cortex-M4 firmwares. This
can be archived using bootm_size, which limits the image
processing range of the boot commands.

Move the device tree standard load address to a higher address
which aligns better with what we are doing on other boards.

Signed-off-by: Stefan Agner <stefan at agner.ch>
---
So this is the second version of the patch "arm: vf610: move
device tree after kernel image" which makes use of bootm_size.
I also added an appropriate comment, added variables for
RAM disk, and added kernel_addr_r/fdt_addr_r.

--
Stefan

 include/configs/vf610twr.h | 27 +++++++++++++++++++++------
 1 file changed, 21 insertions(+), 6 deletions(-)

diff --git a/include/configs/vf610twr.h b/include/configs/vf610twr.h
index 324ba8f..7f4260a 100644
--- a/include/configs/vf610twr.h
+++ b/include/configs/vf610twr.h
@@ -116,20 +116,37 @@
 
 #define CONFIG_BOOTDELAY		3
 
-#define CONFIG_LOADADDR			0x82000000
+#define CONFIG_SYS_LOAD_ADDR		0x82000000
 
 /* We boot from the gfxRAM area of the OCRAM. */
 #define CONFIG_SYS_TEXT_BASE		0x3f408000
 #define CONFIG_BOARD_SIZE_LIMIT		524288
 
+/*
+ * We do have 128MB of memory on the Vybrid Tower board. Leave the last
+ * 16MB alone to avoid conflicts with Cortex-M4 firmwares running from
+ * DDR3. Hence, limit the memory range for image processing to 112MB
+ * using bootm_size. All of the following must be within this range.
+ * We have the default load at 32MB into DDR (for the kernel), FDT at
+ * 64MB and the ramdisk 512KB above that (allowing for hopefully never
+ * seen large trees). This allows a reasonable split between ramdisk
+ * and kernel size, where the ram disk can be a bit larger.
+ */
+#define MEM_LAYOUT_ENV_SETTINGS \
+	"bootm_size=0x07000000\0" \
+	"loadaddr=0x82000000\0" \
+	"kernel_addr_r=0x82000000\0" \
+	"fdt_addr=0x84000000\0" \
+	"fdt_addr_r=0x84000000\0" \
+	"rdaddr=0x84080000\0" \
+	"ramdisk_addr_r=0x84080000\0"
+
 #define CONFIG_EXTRA_ENV_SETTINGS \
+	MEM_LAYOUT_ENV_SETTINGS \
 	"script=boot.scr\0" \
 	"image=zImage\0" \
 	"console=ttyLP1\0" \
-	"fdt_high=0xffffffff\0" \
-	"initrd_high=0xffffffff\0" \
 	"fdt_file=vf610-twr.dtb\0" \
-	"fdt_addr=0x81000000\0" \
 	"boot_fdt=try\0" \
 	"ip_dyn=yes\0" \
 	"mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
@@ -224,8 +241,6 @@
 #define CONFIG_SYS_MEMTEST_START	0x80010000
 #define CONFIG_SYS_MEMTEST_END		0x87C00000
 
-#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
-
 /*
  * Stack sizes
  * The stack sizes are set up in start.S using the settings below
-- 
2.6.1