[U-Boot] [PATCH] arm: sunxi: Add icnova-a20-swac defconfig and dts file

Hans de Goede hdegoede at redhat.com
Sat Oct 17 15:47:51 CEST 2015


Hi,

On 01-10-15 11:41, Stefan Roese wrote:
> The ICnova-A20-SWAC is a baseboard, equipped with the ICnova-A20 SoM from
> In-Circuit:
>
> http://wiki.in-circuit.de/index.php5?title=ICnova_A20_SODIMM
> http://linux-sunxi.org/In-Circuit_ICnova_A20
>
> This patch adds support for this board, including ethernet, LCD and USB
> support.

Thanks, I've merged this and it will show up in u-boot-sunxi/next soon.

I've made 2 small changes, see comments inline.

> Signed-off-by: Stefan Roese <sr at denx.de>
> Cc: Marcus Heuer <marcus.heuer at swac.de>
> Cc: Hans de Goede <hdegoede at redhat.com>
> Cc: Ian Campbell <ijc at hellion.org.uk>
> ---
>   arch/arm/dts/Makefile                      |   1 +
>   arch/arm/dts/sun7i-a20-icnova-a20-swac.dts | 177 +++++++++++++++++++++++++++++
>   board/sunxi/MAINTAINERS                    |   5 +
>   configs/icnova-a20-swac_defconfig          |  21 ++++
>   4 files changed, 204 insertions(+)
>   create mode 100644 arch/arm/dts/sun7i-a20-icnova-a20-swac.dts
>   create mode 100644 configs/icnova-a20-swac_defconfig
>
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index 5f10243..1f2661c 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -134,6 +134,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \
>   	sun7i-a20-cubietruck.dtb \
>   	sun7i-a20-hummingbird.dtb \
>   	sun7i-a20-i12-tvbox.dtb \
> +	sun7i-a20-icnova-a20-swac.dtb \
>   	sun7i-a20-m3.dtb \
>   	sun7i-a20-m5.dtb \
>   	sun7i-a20-mk808c.dtb \
> diff --git a/arch/arm/dts/sun7i-a20-icnova-a20-swac.dts b/arch/arm/dts/sun7i-a20-icnova-a20-swac.dts
> new file mode 100644

Please submit this file also to the upstream kernel.

> index 0000000..773fb6f
> --- /dev/null
> +++ b/arch/arm/dts/sun7i-a20-icnova-a20-swac.dts
> @@ -0,0 +1,177 @@
> +/*
> + * Copyright 2013 Maxime Ripard
> + *
> + * Maxime Ripard <maxime.ripard at free-electrons.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful,
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use,
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "sun7i-a20.dtsi"
> +#include "sunxi-common-regulators.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/pinctrl/sun4i-a10.h>
> +
> +/ {
> +	model = "ICnova-A20 SWAC";
> +	compatible = "swac,icnova-a20-swac", "allwinner,sun7i-a20";
> +
> +	aliases {
> +		serial0 = &uart0;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +};
> +
> +&cpu0 {
> +	cpu-supply = <&reg_dcdc2>;
> +};
> +
> +&ehci0 {
> +	status = "okay";
> +};
> +
> +&ehci1 {
> +	status = "okay";
> +};
> +
> +&gmac {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&gmac_pins_mii_a>;
> +	phy = <&phy1>;
> +	phy-mode = "mii";
> +	status = "okay";
> +
> +	phy1: ethernet-phy at 1 {
> +		reg = <1>;
> +	};
> +};
> +
> +&i2c0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c0_pins_a>;
> +	status = "okay";
> +
> +	axp209: pmic at 34 {
> +		reg = <0x34>;
> +		interrupt-parent = <&nmi_intc>;
> +		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> +	};
> +};
> +
> +&i2c1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c1_pins_a>;
> +	status = "okay";
> +};
> +
> +&ir0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&ir0_rx_pins_a>;
> +	status = "okay";
> +};
> +
> +&mmc0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
> +	vmmc-supply = <&reg_vcc3v3>;
> +	bus-width = <4>;
> +	cd-gpios = <&pio 8 5 GPIO_ACTIVE_HIGH>; /* PI5 */
> +	cd-inverted;
> +	status = "okay";
> +};
> +
> +&ohci0 {
> +	status = "okay";
> +};
> +
> +&ohci1 {
> +	status = "okay";
> +};
> +
> +#include "axp209.dtsi"
> +
> +&reg_dcdc2 {
> +	regulator-always-on;
> +	regulator-min-microvolt = <1000000>;
> +	regulator-max-microvolt = <1450000>;
> +	regulator-name = "vdd-cpu";
> +};
> +
> +&reg_dcdc3 {
> +	regulator-always-on;
> +	regulator-min-microvolt = <1000000>;
> +	regulator-max-microvolt = <1400000>;
> +	regulator-name = "vdd-int-dll";
> +};
> +
> +&reg_ldo1 {
> +	regulator-name = "vdd-rtc";
> +};
> +
> +&reg_ldo2 {
> +	regulator-always-on;
> +	regulator-min-microvolt = <3000000>;
> +	regulator-max-microvolt = <3000000>;
> +	regulator-name = "avcc";
> +};
> +
> +&reg_usb1_vbus {
> +	status = "okay";
> +};
> +
> +&reg_usb2_vbus {
> +	status = "okay";
> +};
> +
> +&uart0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart0_pins_a>;
> +	status = "okay";
> +};
> +
> +&usbphy {
> +	usb1_vbus-supply = <&reg_usb1_vbus>;
> +	usb2_vbus-supply = <&reg_usb2_vbus>;
> +	status = "okay";
> +};
> diff --git a/board/sunxi/MAINTAINERS b/board/sunxi/MAINTAINERS
> index 8f95867..c60fda5 100644
> --- a/board/sunxi/MAINTAINERS
> +++ b/board/sunxi/MAINTAINERS
> @@ -112,6 +112,11 @@ M:	Chen-Yu Tsai <wens at csie.org>
>   S:	Maintained
>   F:	configs/Hummingbird_A31_defconfig
>
> +ICnova-A20-SWAC BOARD
> +M:	Stefan Roese <sr at denx.de>
> +S:	Maintained
> +F:	configs/icnova-a20-swac_defconfig
> +
>   INET 3F BOARD
>   M:	Paul Kocialkowski <contact at paulk.fr>
>   S:	Maintained
> diff --git a/configs/icnova-a20-swac_defconfig b/configs/icnova-a20-swac_defconfig
> new file mode 100644
> index 0000000..bd6e0c5
> --- /dev/null
> +++ b/configs/icnova-a20-swac_defconfig
> @@ -0,0 +1,21 @@
> +CONFIG_ARM=y
> +CONFIG_ARCH_SUNXI=y
> +CONFIG_MACH_SUN7I=y
> +CONFIG_DRAM_CLK=384
> +CONFIG_OLD_SUNXI_KERNEL_COMPAT=y

I've dropped this, I understand that you need it, but I do not believe that
ANY defconfig's as shipped upstream should set this.

> +CONFIG_MMC0_CD_PIN="PI5"
> +CONFIG_USB0_VBUS_PIN="PG11"
> +CONFIG_USB0_VBUS_DET="PH7"
> +CONFIG_USB1_VBUS_PIN="PG10"
> +CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:24,pclk_khz:33000,le:45,ri:209,up:22,lo:22,hs:1,vs:1,sync:3,vmode:0"
> +CONFIG_VIDEO_LCD_POWER="PH22"
> +CONFIG_VIDEO_LCD_PANEL_LVDS=y
> +CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-icnova-a20-swac"
> +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> +CONFIG_SPL=y
> +CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_GMAC,CMD_BMP,CMD_UNZIP"

I've dropped AXP209_POWER from these, in u-boot-sunxi/next this has been
turned into a Kconfig bool which is enabled by default on sun7i.

> +# CONFIG_CMD_IMLS is not set
> +# CONFIG_CMD_FLASH is not set
> +# CONFIG_CMD_FPGA is not set
> +CONFIG_ETH_DESIGNWARE=y
> +CONFIG_USB_EHCI_HCD=y

Regards,

Hans


More information about the U-Boot mailing list