[U-Boot] [Patch V7 13/18] armv8/ls1043ardb: Add LS1043ARDB board support
Gong Qianyu
Qianyu.Gong at freescale.com
Thu Oct 22 12:47:06 CEST 2015
From: Mingkai Hu <Mingkai.Hu at freescale.com>
LS1043ARDB Specification:
-------------------------
Memory subsystem:
* 2GByte DDR4 SDRAM (32bit bus)
* 128 Mbyte NOR flash single-chip memory
* 512 Mbyte NAND flash
* 16 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
Ethernet:
* XFI 10G port
* QSGMII with 4x 1G ports
* Two RGMII ports
PCIe:
* PCIe2 (Lanes C) to mini-PCIe slot
* PCIe3 (Lanes D) to PCIe slot
USB 3.0: two super speed USB 3.0 type A ports
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Hou Zhiqiang <B48286 at freescale.com>
Signed-off-by: Li Yang <leoli at freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu at freescale.com>
Signed-off-by: York Sun <yorksun at freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong at freescale.com>
---
V7:
- No change.
V6:
- Move GIC SMMU macros out of ls1043a_common.h.
V5:
- No change.
V4:
- Change arch to layerscape.
- Add PCIe support.
- Move SMMU_BASE, GICC_BASE, GICD_BASE to ls1043a_common.h.
V3:
- Fix message typos.
- Add ddr model number in comments.
- Fix boot options in README.
- Remove some dead code.
V2:
- Replaced ns_access.h with fsl_csu.h.
arch/arm/Kconfig | 7 +
arch/arm/cpu/armv8/fsl-layerscape/Makefile | 4 +
arch/arm/cpu/armv8/fsl-layerscape/ls1043a_serdes.c | 86 ++++++++++
board/freescale/ls1043ardb/Kconfig | 16 ++
board/freescale/ls1043ardb/MAINTAINERS | 7 +
board/freescale/ls1043ardb/Makefile | 9 +
board/freescale/ls1043ardb/README | 85 +++++++++
board/freescale/ls1043ardb/cpld.c | 115 +++++++++++++
board/freescale/ls1043ardb/cpld.h | 43 +++++
board/freescale/ls1043ardb/ddr.c | 191 +++++++++++++++++++++
board/freescale/ls1043ardb/ddr.h | 45 +++++
board/freescale/ls1043ardb/ls1043ardb.c | 131 ++++++++++++++
configs/ls1043ardb_defconfig | 4 +
include/configs/ls1043a_common.h | 174 +++++++++++++++++++
include/configs/ls1043ardb.h | 191 +++++++++++++++++++++
15 files changed, 1108 insertions(+)
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 7981355..bd99bfb 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -631,6 +631,12 @@ config TARGET_LS1021ATWR
select CPU_V7
select SUPPORT_SPL
+config TARGET_LS1043ARDB
+ bool "Support ls1043ardb"
+ select ARM64
+ help
+ Support for Freescale LS1043ARDB platform.
+
config TARGET_H2200
bool "Support h2200"
select CPU_PXA
@@ -745,6 +751,7 @@ source "board/freescale/ls2085aqds/Kconfig"
source "board/freescale/ls2085ardb/Kconfig"
source "board/freescale/ls1021aqds/Kconfig"
source "board/freescale/ls1021atwr/Kconfig"
+source "board/freescale/ls1043ardb/Kconfig"
source "board/freescale/mx23evk/Kconfig"
source "board/freescale/mx25pdk/Kconfig"
source "board/freescale/mx28evk/Kconfig"
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/Makefile b/arch/arm/cpu/armv8/fsl-layerscape/Makefile
index 4754e59..6fa08c8 100644
--- a/arch/arm/cpu/armv8/fsl-layerscape/Makefile
+++ b/arch/arm/cpu/armv8/fsl-layerscape/Makefile
@@ -23,4 +23,8 @@ endif
ifneq ($(CONFIG_LS2085A),)
obj-$(CONFIG_SYS_HAS_SERDES) += ls2085a_serdes.o
+else
+ifneq ($(CONFIG_LS1043A),)
+obj-$(CONFIG_SYS_HAS_SERDES) += ls1043a_serdes.o
+endif
endif
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/ls1043a_serdes.c b/arch/arm/cpu/armv8/fsl-layerscape/ls1043a_serdes.c
new file mode 100644
index 0000000..e54d389
--- /dev/null
+++ b/arch/arm/cpu/armv8/fsl-layerscape/ls1043a_serdes.c
@@ -0,0 +1,86 @@
+/*
+ * Copyright 2015 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/fsl_serdes.h>
+#include <asm/arch/immap_lsch2.h>
+
+struct serdes_config {
+ u32 protocol;
+ u8 lanes[SRDS_MAX_LANES];
+};
+
+static struct serdes_config serdes1_cfg_tbl[] = {
+ /* SerDes 1 */
+ {0x1555, {XFI_FM1_MAC9, PCIE1, PCIE2, PCIE3} },
+ {0x2555, {SGMII_2500_FM1_DTSEC9, PCIE1, PCIE2, PCIE3} },
+ {0x4555, {QSGMII_FM1_A, PCIE1, PCIE2, PCIE3} },
+ {0x4558, {QSGMII_FM1_A, PCIE1, PCIE2, SATA1} },
+ {0x1355, {XFI_FM1_MAC9, SGMII_FM1_DTSEC2, PCIE2, PCIE3} },
+ {0x2355, {SGMII_2500_FM1_DTSEC9, SGMII_FM1_DTSEC2, PCIE2, PCIE3} },
+ {0x3335, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC2, SGMII_FM1_DTSEC5,
+ PCIE3} },
+ {0x3355, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC2, PCIE2, PCIE3} },
+ {0x3358, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC2, PCIE2, SATA1} },
+ {0x3555, {SGMII_FM1_DTSEC9, PCIE1, PCIE2, PCIE3} },
+ {0x3558, {SGMII_FM1_DTSEC9, PCIE1, PCIE2, SATA1} },
+ {0x7000, {PCIE1, PCIE1, PCIE1, PCIE1} },
+ {0x9998, {PCIE1, PCIE2, PCIE3, SATA1} },
+ {0x6058, {PCIE1, PCIE1, PCIE2, SATA1} },
+ {0x1455, {XFI_FM1_MAC9, QSGMII_FM1_A, PCIE2, PCIE3} },
+ {0x2455, {SGMII_2500_FM1_DTSEC9, QSGMII_FM1_A, PCIE2, PCIE3} },
+ {0x2255, {SGMII_2500_FM1_DTSEC9, SGMII_2500_FM1_DTSEC2, PCIE2, PCIE3} },
+ {0x3333, {SGMII_FM1_DTSEC9, SGMII_FM1_DTSEC2, SGMII_FM1_DTSEC5,
+ SGMII_FM1_DTSEC6} },
+ {}
+};
+
+static struct serdes_config *serdes_cfg_tbl[] = {
+ serdes1_cfg_tbl,
+};
+
+enum srds_prtcl serdes_get_prtcl(int serdes, int cfg, int lane)
+{
+ struct serdes_config *ptr;
+
+ if (serdes >= ARRAY_SIZE(serdes_cfg_tbl))
+ return 0;
+
+ ptr = serdes_cfg_tbl[serdes];
+ while (ptr->protocol) {
+ if (ptr->protocol == cfg)
+ return ptr->lanes[lane];
+ ptr++;
+ }
+
+ return 0;
+}
+
+int is_serdes_prtcl_valid(int serdes, u32 prtcl)
+{
+ int i;
+ struct serdes_config *ptr;
+
+ if (serdes >= ARRAY_SIZE(serdes_cfg_tbl))
+ return 0;
+
+ ptr = serdes_cfg_tbl[serdes];
+ while (ptr->protocol) {
+ if (ptr->protocol == prtcl)
+ break;
+ ptr++;
+ }
+
+ if (!ptr->protocol)
+ return 0;
+
+ for (i = 0; i < SRDS_MAX_LANES; i++) {
+ if (ptr->lanes[i] != NONE)
+ return 1;
+ }
+
+ return 0;
+}
diff --git a/board/freescale/ls1043ardb/Kconfig b/board/freescale/ls1043ardb/Kconfig
new file mode 100644
index 0000000..51818ec
--- /dev/null
+++ b/board/freescale/ls1043ardb/Kconfig
@@ -0,0 +1,16 @@
+
+if TARGET_LS1043ARDB
+
+config SYS_BOARD
+ default "ls1043ardb"
+
+config SYS_VENDOR
+ default "freescale"
+
+config SYS_SOC
+ default "fsl-layerscape"
+
+config SYS_CONFIG_NAME
+ default "ls1043ardb"
+
+endif
diff --git a/board/freescale/ls1043ardb/MAINTAINERS b/board/freescale/ls1043ardb/MAINTAINERS
new file mode 100644
index 0000000..b8f6be2
--- /dev/null
+++ b/board/freescale/ls1043ardb/MAINTAINERS
@@ -0,0 +1,7 @@
+LS1043A BOARD
+M: Mingkai Hu <Mingkai.hu at freescale.com>
+S: Maintained
+F: board/freescale/ls1043ardb/
+F: board/freescale/ls1043ardb/ls1043ardb.c
+F: include/configs/ls1043ardb.h
+F: configs/ls1043ardb_defconfig
diff --git a/board/freescale/ls1043ardb/Makefile b/board/freescale/ls1043ardb/Makefile
new file mode 100644
index 0000000..dd17e2e
--- /dev/null
+++ b/board/freescale/ls1043ardb/Makefile
@@ -0,0 +1,9 @@
+#
+# Copyright 2015 Freescale Semiconductor
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y += cpld.o
+obj-y += ddr.o
+obj-y += ls1043ardb.o
diff --git a/board/freescale/ls1043ardb/README b/board/freescale/ls1043ardb/README
new file mode 100644
index 0000000..d5925a9
--- /dev/null
+++ b/board/freescale/ls1043ardb/README
@@ -0,0 +1,85 @@
+Overview
+--------
+The LS1043A Reference Design Board (RDB) is a high-performance computing,
+evaluation, and development platform that supports the QorIQ LS1043A
+LayerScape Architecture processor. The LS1043ARDB provides SW development
+platform for the Freescale LS1043A processor series, with a complete
+debugging environment. The LS1043A RDB is lead-free and RoHS-compliant.
+
+LS1043A SoC Overview
+--------------------
+The LS1043A integrated multicore processor combines four ARM Cortex-A53
+processor cores with datapath acceleration optimized for L2/3 packet
+processing, single pass security offload and robust traffic management
+and quality of service.
+
+The LS1043A SoC includes the following function and features:
+ - Four 64-bit ARM Cortex-A53 CPUs
+ - 1 MB unified L2 Cache
+ - One 32-bit DDR3L/DDR4 SDRAM memory controllers with ECC and interleaving
+ support
+ - Data Path Acceleration Architecture (DPAA) incorporating acceleration the
+ the following functions:
+ - Packet parsing, classification, and distribution (FMan)
+ - Queue management for scheduling, packet sequencing, and congestion
+ management (QMan)
+ - Hardware buffer management for buffer allocation and de-allocation (BMan)
+ - Cryptography acceleration (SEC)
+ - Ethernet interfaces by FMan
+ - Up to 1 x XFI supporting 10G interface
+ - Up to 1 x QSGMII
+ - Up to 4 x SGMII supporting 1000Mbps
+ - Up to 2 x SGMII supporting 2500Mbps
+ - Up to 2 x RGMII supporting 1000Mbps
+ - High-speed peripheral interfaces
+ - Three PCIe 2.0 controllers, one supporting x4 operation
+ - One serial ATA (SATA 3.0) controllers
+ - Additional peripheral interfaces
+ - Three high-speed USB 3.0 controllers with integrated PHY
+ - Enhanced secure digital host controller (eSDXC/eMMC)
+ - Quad Serial Peripheral Interface (QSPI) Controller
+ - Serial peripheral interface (SPI) controller
+ - Four I2C controllers
+ - Two DUARTs
+ - Integrated flash controller supporting NAND and NOR flash
+ - QorIQ platform's trust architecture 2.1
+
+ LS1043ARDB board Overview
+ -----------------------
+ - SERDES Connections, 4 lanes supporting:
+ - PCI Express 2.0 with two PCIe connectors supporting: miniPCIe card and
+ standard PCIe card
+ - QSGMII with x4 RJ45 connector
+ - XFI with x1 RJ45 connector
+ - DDR Controller
+ - 2GB 32bits DDR4 SDRAM. Support rates of up to 1600MT/s
+ -IFC/Local Bus
+ - One 128MB NOR flash 16-bit data bus
+ - One 512 MB NAND flash with ECC support
+ - CPLD connection
+ - USB 3.0
+ - Two super speed USB 3.0 Type A ports
+ - SDHC: connects directly to a full SD/MMC slot
+ - DSPI: 16 MB high-speed flash Memory for boot code and storage (up to 108MHz)
+ - 4 I2C controllers
+ - UART
+ - Two 4-pin serial ports at up to 115.2 Kbit/s
+ - Two DB9 D-Type connectors supporting one Serial port each
+ - ARM JTAG support
+
+Memory map from core's view
+----------------------------
+Start Address End Address Description Size
+0x00_0000_0000 0x00_000F_FFFF Secure Boot ROM 1MB
+0x00_0100_0000 0x00_0FFF_FFFF CCSRBAR 240MB
+0x00_1000_0000 0x00_1000_FFFF OCRAM0 64KB
+0x00_1001_0000 0x00_1001_FFFF OCRAM1 64KB
+0x00_2000_0000 0x00_20FF_FFFF DCSR 16MB
+0x00_6000_0000 0x00_67FF_FFFF IFC - NOR Flash 128MB
+0x00_7E80_0000 0x00_7E80_FFFF IFC - NAND Flash 64KB
+0x00_7FB0_0000 0x00_7FB0_0FFF IFC - FPGA 4KB
+0x00_8000_0000 0x00_FFFF_FFFF DRAM1 2GB
+
+Booting Options
+---------------
+a) NOR boot
diff --git a/board/freescale/ls1043ardb/cpld.c b/board/freescale/ls1043ardb/cpld.c
new file mode 100644
index 0000000..3f1101e
--- /dev/null
+++ b/board/freescale/ls1043ardb/cpld.c
@@ -0,0 +1,115 @@
+/*
+ * Copyright 2015 Freescale Semiconductor
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ * Freescale LS1043ARDB board-specific CPLD controlling supports.
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/io.h>
+#include "cpld.h"
+
+u8 cpld_read(unsigned int reg)
+{
+ void *p = (void *)CONFIG_SYS_CPLD_BASE;
+
+ return in_8(p + reg);
+}
+
+void cpld_write(unsigned int reg, u8 value)
+{
+ void *p = (void *)CONFIG_SYS_CPLD_BASE;
+
+ out_8(p + reg, value);
+}
+
+/* Set the boot bank to the alternate bank */
+void cpld_set_altbank(void)
+{
+ u8 reg4 = CPLD_READ(soft_mux_on);
+ u8 reg7 = CPLD_READ(vbank);
+
+ CPLD_WRITE(soft_mux_on, reg4 | CPLD_SW_MUX_BANK_SEL);
+
+ reg7 = (reg7 & ~CPLD_BANK_SEL_MASK) | CPLD_BANK_SEL_ALTBANK;
+ CPLD_WRITE(vbank, reg7);
+
+ CPLD_WRITE(system_rst, 1);
+}
+
+/* Set the boot bank to the default bank */
+void cpld_set_defbank(void)
+{
+ CPLD_WRITE(global_rst, 1);
+}
+
+#ifdef DEBUG
+static void cpld_dump_regs(void)
+{
+ printf("cpld_ver = %x\n", CPLD_READ(cpld_ver));
+ printf("cpld_ver_sub = %x\n", CPLD_READ(cpld_ver_sub));
+ printf("pcba_ver = %x\n", CPLD_READ(pcba_ver));
+ printf("soft_mux_on = %x\n", CPLD_READ(soft_mux_on));
+ printf("cfg_rcw_src1 = %x\n", CPLD_READ(cfg_rcw_src1));
+ printf("cfg_rcw_src2 = %x\n", CPLD_READ(cfg_rcw_src2));
+ printf("vbank = %x\n", CPLD_READ(vbank));
+ printf("sysclk_sel = %x\n", CPLD_READ(sysclk_sel));
+ printf("uart_sel = %x\n", CPLD_READ(uart_sel));
+ printf("sd1refclk_sel = %x\n", CPLD_READ(sd1refclk_sel));
+ printf("tdmclk_mux_sel = %x\n", CPLD_READ(tdmclk_mux_sel));
+ printf("sdhc_spics_sel = %x\n", CPLD_READ(sdhc_spics_sel));
+ printf("status_led = %x\n", CPLD_READ(status_led));
+ putc('\n');
+}
+#endif
+
+void cpld_rev_bit(unsigned char *value)
+{
+ u8 rev_val, val;
+ int i;
+
+ val = *value;
+ rev_val = val & 1;
+ for (i = 1; i <= 7; i++) {
+ val >>= 1;
+ rev_val <<= 1;
+ rev_val |= val & 1;
+ }
+
+ *value = rev_val;
+}
+
+int do_cpld(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ int rc = 0;
+
+ if (argc <= 1)
+ return cmd_usage(cmdtp);
+
+ if (strcmp(argv[1], "reset") == 0) {
+ if (strcmp(argv[2], "altbank") == 0)
+ cpld_set_altbank();
+ else
+ cpld_set_defbank();
+#ifdef DEBUG
+ } else if (strcmp(argv[1], "dump") == 0) {
+ cpld_dump_regs();
+#endif
+ } else {
+ rc = cmd_usage(cmdtp);
+ }
+
+ return rc;
+}
+
+U_BOOT_CMD(
+ cpld, CONFIG_SYS_MAXARGS, 1, do_cpld,
+ "Reset the board or alternate bank",
+ "reset: reset to default bank\n"
+ "cpld reset altbank: reset to alternate bank\n"
+#ifdef DEBUG
+ "cpld dump - display the CPLD registers\n"
+#endif
+);
diff --git a/board/freescale/ls1043ardb/cpld.h b/board/freescale/ls1043ardb/cpld.h
new file mode 100644
index 0000000..ea4efd8
--- /dev/null
+++ b/board/freescale/ls1043ardb/cpld.h
@@ -0,0 +1,43 @@
+/*
+ * Copyright 2015 Freescale Semiconductor
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CPLD_H__
+#define __CPLD_H__
+
+/*
+ * CPLD register set of LS1043ARDB board-specific.
+ */
+struct cpld_data {
+ u8 cpld_ver; /* 0x0 - CPLD Major Revision Register */
+ u8 cpld_ver_sub; /* 0x1 - CPLD Minor Revision Register */
+ u8 pcba_ver; /* 0x2 - PCBA Revision Register */
+ u8 system_rst; /* 0x3 - system reset register */
+ u8 soft_mux_on; /* 0x4 - Switch Control Enable Register */
+ u8 cfg_rcw_src1; /* 0x5 - Reset config word 1 */
+ u8 cfg_rcw_src2; /* 0x6 - Reset config word 1 */
+ u8 vbank; /* 0x7 - Flash bank selection Control */
+ u8 sysclk_sel; /* 0x8 - */
+ u8 uart_sel; /* 0x9 - */
+ u8 sd1refclk_sel; /* 0xA - */
+ u8 tdmclk_mux_sel; /* 0xB - */
+ u8 sdhc_spics_sel; /* 0xC - */
+ u8 status_led; /* 0xD - */
+ u8 global_rst; /* 0xE - */
+};
+
+u8 cpld_read(unsigned int reg);
+void cpld_write(unsigned int reg, u8 value);
+void cpld_rev_bit(unsigned char *value);
+
+#define CPLD_READ(reg) cpld_read(offsetof(struct cpld_data, reg))
+#define CPLD_WRITE(reg, value) \
+ cpld_write(offsetof(struct cpld_data, reg), value)
+
+/* CPLD on IFC */
+#define CPLD_SW_MUX_BANK_SEL 0x40
+#define CPLD_BANK_SEL_MASK 0x07
+#define CPLD_BANK_SEL_ALTBANK 0x04
+#endif
diff --git a/board/freescale/ls1043ardb/ddr.c b/board/freescale/ls1043ardb/ddr.c
new file mode 100644
index 0000000..b181579
--- /dev/null
+++ b/board/freescale/ls1043ardb/ddr.c
@@ -0,0 +1,191 @@
+/*
+ * Copyright 2015 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+#include "ddr.h"
+#ifdef CONFIG_FSL_DEEP_SLEEP
+#include <fsl_sleep.h>
+#endif
+
+DECLARE_GLOBAL_DATA_PTR;
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+ dimm_params_t *pdimm,
+ unsigned int ctrl_num)
+{
+ const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
+ ulong ddr_freq;
+
+ if (ctrl_num > 1) {
+ printf("Not supported controller number %d\n", ctrl_num);
+ return;
+ }
+ if (!pdimm->n_ranks)
+ return;
+
+ pbsp = udimms[0];
+
+ /* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
+ * freqency and n_banks specified in board_specific_parameters table.
+ */
+ ddr_freq = get_ddr_freq(0) / 1000000;
+ while (pbsp->datarate_mhz_high) {
+ if (pbsp->n_ranks == pdimm->n_ranks) {
+ if (ddr_freq <= pbsp->datarate_mhz_high) {
+ popts->clk_adjust = pbsp->clk_adjust;
+ popts->wrlvl_start = pbsp->wrlvl_start;
+ popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+ popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+ popts->cpo_override = pbsp->cpo_override;
+ popts->write_data_delay =
+ pbsp->write_data_delay;
+ goto found;
+ }
+ pbsp_highest = pbsp;
+ }
+ pbsp++;
+ }
+
+ if (pbsp_highest) {
+ printf("Error: board specific timing not found for %lu MT/s\n",
+ ddr_freq);
+ printf("Trying to use the highest speed (%u) parameters\n",
+ pbsp_highest->datarate_mhz_high);
+ popts->clk_adjust = pbsp_highest->clk_adjust;
+ popts->wrlvl_start = pbsp_highest->wrlvl_start;
+ popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+ popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+ } else {
+ panic("DIMM is not supported by this board");
+ }
+found:
+ debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n",
+ pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb);
+
+ /* force DDR bus width to 32 bits */
+ popts->data_bus_width = 1;
+ popts->otf_burst_chop_en = 0;
+ popts->burst_length = DDR_BL8;
+
+ /*
+ * Factors to consider for half-strength driver enable:
+ * - number of DIMMs installed
+ */
+ popts->half_strength_driver_enable = 1;
+ /*
+ * Write leveling override
+ */
+ popts->wrlvl_override = 1;
+ popts->wrlvl_sample = 0xf;
+
+ /*
+ * Rtt and Rtt_WR override
+ */
+ popts->rtt_override = 0;
+
+ /* Enable ZQ calibration */
+ popts->zq_en = 1;
+
+ popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
+ popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
+ DDR_CDR2_VREF_OVRD(70); /* Vref = 70% */
+}
+
+/* DDR model number: MT40A512M8HX-093E */
+#ifdef CONFIG_SYS_DDR_RAW_TIMING
+dimm_params_t ddr_raw_timing = {
+ .n_ranks = 1,
+ .rank_density = 2147483648u,
+ .capacity = 2147483648u,
+ .primary_sdram_width = 32,
+ .ec_sdram_width = 0,
+ .registered_dimm = 0,
+ .mirrored_dimm = 0,
+ .n_row_addr = 15,
+ .n_col_addr = 10,
+ .bank_addr_bits = 0,
+ .bank_group_bits = 2,
+ .edc_config = 0,
+ .burst_lengths_bitmask = 0x0c,
+
+ .tckmin_x_ps = 938,
+ .tckmax_ps = 1500,
+ .caslat_x = 0x000DFA00,
+ .taa_ps = 13500,
+ .trcd_ps = 13500,
+ .trp_ps = 13500,
+ .tras_ps = 33000,
+ .trc_ps = 46500,
+ .trfc1_ps = 260000,
+ .trfc2_ps = 160000,
+ .trfc4_ps = 110000,
+ .tfaw_ps = 21000,
+ .trrds_ps = 3700,
+ .trrdl_ps = 5300,
+ .tccdl_ps = 5355,
+ .refresh_rate_ps = 7800000,
+ .dq_mapping[0] = 0x0,
+ .dq_mapping[1] = 0x0,
+ .dq_mapping[2] = 0x0,
+ .dq_mapping[3] = 0x0,
+ .dq_mapping[4] = 0x0,
+ .dq_mapping[5] = 0x0,
+ .dq_mapping[6] = 0x0,
+ .dq_mapping[7] = 0x0,
+ .dq_mapping[8] = 0x0,
+ .dq_mapping[9] = 0x0,
+ .dq_mapping[10] = 0x0,
+ .dq_mapping[11] = 0x0,
+ .dq_mapping[12] = 0x0,
+ .dq_mapping[13] = 0x0,
+ .dq_mapping[14] = 0x0,
+ .dq_mapping[15] = 0x0,
+ .dq_mapping[16] = 0x0,
+ .dq_mapping[17] = 0x0,
+ .dq_mapping_ors = 0,
+};
+
+int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
+ unsigned int controller_number,
+ unsigned int dimm_number)
+{
+ static const char dimm_model[] = "Fixed DDR on board";
+
+ if (((controller_number == 0) && (dimm_number == 0)) ||
+ ((controller_number == 1) && (dimm_number == 0))) {
+ memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t));
+ memset(pdimm->mpart, 0, sizeof(pdimm->mpart));
+ memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1);
+ }
+
+ return 0;
+}
+#endif
+
+phys_size_t initdram(int board_type)
+{
+ phys_size_t dram_size;
+
+#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_SPL)
+ puts("Initializing DDR....\n");
+ dram_size = fsl_ddr_sdram();
+#else
+ dram_size = fsl_ddr_sdram_size();
+#endif
+#ifdef CONFIG_FSL_DEEP_SLEEP
+ fsl_dp_ddr_restore();
+#endif
+
+ return dram_size;
+}
+
+void dram_init_banksize(void)
+{
+ gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+ gd->bd->bi_dram[0].size = gd->ram_size;
+}
diff --git a/board/freescale/ls1043ardb/ddr.h b/board/freescale/ls1043ardb/ddr.h
new file mode 100644
index 0000000..b17eb80
--- /dev/null
+++ b/board/freescale/ls1043ardb/ddr.h
@@ -0,0 +1,45 @@
+/*
+ * Copyright 2015 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __DDR_H__
+#define __DDR_H__
+struct board_specific_parameters {
+ u32 n_ranks;
+ u32 datarate_mhz_high;
+ u32 rank_gb;
+ u32 clk_adjust;
+ u32 wrlvl_start;
+ u32 wrlvl_ctl_2;
+ u32 wrlvl_ctl_3;
+ u32 cpo_override;
+ u32 write_data_delay;
+ u32 force_2t;
+};
+
+/*
+ * These tables contain all valid speeds we want to override with board
+ * specific parameters. datarate_mhz_high values need to be in ascending order
+ * for each n_ranks group.
+ */
+static const struct board_specific_parameters udimm0[] = {
+ /*
+ * memory controller 0
+ * num| hi| rank| clk| wrlvl | wrlvl | wrlvl | cpo |wrdata|2T
+ * ranks| mhz| GB |adjst| start | ctl2 | ctl3 | |delay |
+ */
+#ifdef CONFIG_SYS_FSL_DDR4
+ {1, 1666, 0, 6, 7, 0x07090800, 0x00000000,},
+ {1, 1900, 0, 6, 7, 0x07090800, 0x00000000,},
+ {1, 2200, 0, 6, 7, 0x07090800, 0x00000000,},
+#endif
+ {}
+};
+
+static const struct board_specific_parameters *udimms[] = {
+ udimm0,
+};
+
+#endif
diff --git a/board/freescale/ls1043ardb/ls1043ardb.c b/board/freescale/ls1043ardb/ls1043ardb.c
new file mode 100644
index 0000000..5b7f814
--- /dev/null
+++ b/board/freescale/ls1043ardb/ls1043ardb.c
@@ -0,0 +1,131 @@
+/*
+ * Copyright 2015 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <asm/io.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/fsl_serdes.h>
+#include <asm/arch/soc.h>
+#include <hwconfig.h>
+#include <ahci.h>
+#include <scsi.h>
+#include <fsl_csu.h>
+#include <fsl_esdhc.h>
+#include <fsl_ifc.h>
+#include "cpld.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkboard(void)
+{
+ static const char *freq[3] = {"100.00MHZ", "156.25MHZ"};
+ u8 cfg_rcw_src1, cfg_rcw_src2;
+ u32 cfg_rcw_src;
+ u32 sd1refclk_sel;
+
+ printf("Board: LS1043ARDB, boot from ");
+
+ cfg_rcw_src1 = CPLD_READ(cfg_rcw_src1);
+ cfg_rcw_src2 = CPLD_READ(cfg_rcw_src2);
+ cpld_rev_bit(&cfg_rcw_src1);
+ cfg_rcw_src = cfg_rcw_src1;
+ cfg_rcw_src = (cfg_rcw_src << 1) | cfg_rcw_src2;
+
+ if (cfg_rcw_src == 0x25)
+ printf("vBank %d\n", CPLD_READ(vbank));
+ else if (cfg_rcw_src == 0x106)
+ puts("NAND\n");
+ else
+ printf("Invalid setting of SW4\n");
+
+ printf("CPLD: V%x.%x\nPCBA: V%x.0\n", CPLD_READ(cpld_ver),
+ CPLD_READ(cpld_ver_sub), CPLD_READ(pcba_ver));
+
+ puts("SERDES Reference Clocks:\n");
+ sd1refclk_sel = CPLD_READ(sd1refclk_sel);
+ printf("SD1_CLK1 = %s, SD1_CLK2 = %s\n", freq[sd1refclk_sel], freq[0]);
+
+ return 0;
+}
+
+int dram_init(void)
+{
+ gd->ram_size = initdram(0);
+
+ return 0;
+}
+
+int board_early_init_f(void)
+{
+ fsl_lsch2_early_init_f();
+ return 0;
+}
+
+int board_init(void)
+{
+ struct ccsr_cci400 *cci = (struct ccsr_cci400 *)CONFIG_SYS_CCI400_ADDR;
+
+ /*
+ * Set CCI-400 control override register to enable barrier
+ * transaction
+ */
+ out_le32(&cci->ctrl_ord, CCI400_CTRLORD_EN_BARRIER);
+
+#ifdef CONFIG_FSL_IFC
+ init_final_memctl_regs();
+#endif
+
+#ifdef CONFIG_ENV_IS_NOWHERE
+ gd->env_addr = (ulong)&default_environment[0];
+#endif
+
+#ifdef CONFIG_LAYERSCAPE_NS_ACCESS
+ enable_layerscape_ns_access();
+#endif
+
+ return 0;
+}
+
+int config_board_mux(void)
+{
+ return 0;
+}
+
+#if defined(CONFIG_MISC_INIT_R)
+int misc_init_r(void)
+{
+ config_board_mux();
+
+ return 0;
+}
+#endif
+
+int ft_board_setup(void *blob, bd_t *bd)
+{
+ ft_cpu_setup(blob, bd);
+
+ return 0;
+}
+
+u8 flash_read8(void *addr)
+{
+ return __raw_readb(addr + 1);
+}
+
+void flash_write16(u16 val, void *addr)
+{
+ u16 shftval = (((val >> 8) & 0xff) | ((val << 8) & 0xff00));
+
+ __raw_writew(shftval, addr);
+}
+
+u16 flash_read16(void *addr)
+{
+ u16 val = __raw_readw(addr);
+
+ return (((val) >> 8) & 0x00ff) | (((val) << 8) & 0xff00);
+}
diff --git a/configs/ls1043ardb_defconfig b/configs/ls1043ardb_defconfig
new file mode 100644
index 0000000..ae84d2e
--- /dev/null
+++ b/configs/ls1043ardb_defconfig
@@ -0,0 +1,4 @@
+CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4"
+CONFIG_ARM=y
+CONFIG_TARGET_LS1043ARDB=y
+CONFIG_FSL_LAYERSCAPE=y
diff --git a/include/configs/ls1043a_common.h b/include/configs/ls1043a_common.h
new file mode 100644
index 0000000..195d310
--- /dev/null
+++ b/include/configs/ls1043a_common.h
@@ -0,0 +1,174 @@
+/*
+ * Copyright (C) 2015 Freescale Semiconductor
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __LS1043A_COMMON_H
+#define __LS1043A_COMMON_H
+
+#define CONFIG_SYS_GENERIC_BOARD
+
+#define CONFIG_REMAKE_ELF
+#define CONFIG_FSL_LAYERSCAPE
+#define CONFIG_FSL_LSCH2
+#define CONFIG_LS1043A
+#define CONFIG_SYS_FSL_CLK
+#define CONFIG_GICV2
+
+#include <asm/arch/config.h>
+#ifdef CONFIG_SYS_FSL_SRDS_1
+#define CONFIG_SYS_HAS_SERDES
+#endif
+
+/* Link Definitions */
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
+
+#define CONFIG_SUPPORT_RAW_INITRD
+
+#define CONFIG_SKIP_LOWLEVEL_INIT
+#define CONFIG_BOARD_EARLY_INIT_F 1
+
+/* Flat Device Tree Definitions */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
+
+#ifndef CONFIG_SYS_FSL_DDR4
+#define CONFIG_SYS_FSL_DDR3 /* Use DDR3 memory */
+#endif
+
+#define CONFIG_VERY_BIG_RAM
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000
+#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+
+/* Generic Timer Definitions */
+#define COUNTER_FREQUENCY 25000000 /* 25MHz */
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 1024 * 1024)
+
+/* Serial Port */
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0))
+
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/* IFC */
+#define CONFIG_FSL_IFC
+/*
+ * CONFIG_SYS_FLASH_BASE has the final address (core view)
+ * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
+ * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
+ * CONFIG_SYS_TEXT_BASE is linked to 0x60000000 for booting
+ */
+#define CONFIG_SYS_FLASH_BASE 0x60000000
+#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_FLASH_BASE_PHYS_EARLY 0x00000000
+
+#ifndef CONFIG_SYS_NO_FLASH
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
+#endif
+
+/* I2C */
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1
+#define CONFIG_SYS_I2C_MXC_I2C2
+#define CONFIG_SYS_I2C_MXC_I2C3
+#define CONFIG_SYS_I2C_MXC_I2C4
+
+/* PCIe */
+#define CONFIG_PCI /* Enable PCI/PCIE */
+#define CONFIG_PCIE1 /* PCIE controller 1 */
+#define CONFIG_PCIE2 /* PCIE controller 2 */
+#define CONFIG_PCIE3 /* PCIE controller 3 */
+#define CONFIG_PCIE_LAYERSCAPE /* Use common FSL Layerscape PCIe code */
+#define FSL_PCIE_COMPAT "fsl,ls1043a-pcie"
+
+#define CONFIG_SYS_PCI_64BIT
+
+#define CONFIG_SYS_PCIE_CFG0_PHYS_OFF 0x00000000
+#define CONFIG_SYS_PCIE_CFG0_SIZE 0x00001000 /* 4k */
+#define CONFIG_SYS_PCIE_CFG1_PHYS_OFF 0x00001000
+#define CONFIG_SYS_PCIE_CFG1_SIZE 0x00001000 /* 4k */
+
+#define CONFIG_SYS_PCIE_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE_IO_PHYS_OFF 0x00010000
+#define CONFIG_SYS_PCIE_IO_SIZE 0x00010000 /* 64k */
+
+#define CONFIG_SYS_PCIE_MEM_BUS 0x40000000
+#define CONFIG_SYS_PCIE_MEM_PHYS_OFF 0x40000000
+#define CONFIG_SYS_PCIE_MEM_SIZE 0x40000000 /* 1G */
+
+#ifdef CONFIG_PCI
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP
+#define CONFIG_E1000
+#define CONFIG_PCI_SCAN_SHOW
+#define CONFIG_CMD_PCI
+#endif
+
+/* Command line configuration */
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_PING
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
+#define CONFIG_ARCH_EARLY_INIT_R
+#define CONFIG_BOARD_LATE_INIT
+
+#define CONFIG_HWCONFIG
+#define HWCONFIG_BUFFER_SIZE 128
+
+/* Initial environment variables */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "hwconfig=fsl_ddr:bank_intlv=auto\0" \
+ "loadaddr=0x80100000\0" \
+ "kernel_addr=0x100000\0" \
+ "ramdisk_addr=0x800000\0" \
+ "ramdisk_size=0x2000000\0" \
+ "fdt_high=0xffffffffffffffff\0" \
+ "initrd_high=0xffffffffffffffff\0" \
+ "kernel_start=0x61200000\0" \
+ "kernel_load=0x807f0000\0" \
+ "kernel_size=0x1000000\0" \
+ "console=ttyAMA0,38400n8\0"
+
+#define CONFIG_BOOTARGS "console=ttyS0,115200 root=/dev/ram0 " \
+ "earlycon=uart8250,0x21c0500,115200"
+#define CONFIG_BOOTCOMMAND "cp.b $kernel_start $kernel_load " \
+ "$kernel_size && bootm $kernel_load"
+#define CONFIG_BOOTDELAY 10
+
+/* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PROMPT "=> "
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_CMDLINE_EDITING 1
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_MAXARGS 64 /* max command args */
+
+#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
+
+#endif /* __LS1043A_COMMON_H */
diff --git a/include/configs/ls1043ardb.h b/include/configs/ls1043ardb.h
new file mode 100644
index 0000000..1f66201
--- /dev/null
+++ b/include/configs/ls1043ardb.h
@@ -0,0 +1,191 @@
+/*
+ * Copyright 2015 Freescale Semiconductor
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __LS1043ARDB_H__
+#define __LS1043ARDB_H__
+
+#include "ls1043a_common.h"
+
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+#define CONFIG_SYS_TEXT_BASE 0x60100000
+
+#define CONFIG_SYS_CLK_FREQ 100000000
+#define CONFIG_DDR_CLK_FREQ 100000000
+
+#define CONFIG_LAYERSCAPE_NS_ACCESS
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+/* Physical Memory Map */
+#define CONFIG_CHIP_SELECTS_PER_CTRL 4
+#define CONFIG_NR_DRAM_BANKS 1
+
+#define CONFIG_SYS_SPD_BUS_NUM 0
+
+#define CONFIG_FSL_DDR_BIST
+#define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */
+#define CONFIG_SYS_DDR_RAW_TIMING
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
+
+/*
+ * NOR Flash Definitions
+ */
+#define CONFIG_SYS_NOR_CSPR_EXT (0x0)
+#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
+#define CONFIG_SYS_NOR_CSPR \
+ (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
+ CSPR_PORT_SIZE_16 | \
+ CSPR_MSEL_NOR | \
+ CSPR_V)
+
+/* NOR Flash Timing Params */
+#define CONFIG_SYS_NOR_CSOR (CSOR_NOR_ADM_SHIFT(4) | \
+ CSOR_NOR_TRHZ_80)
+#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x1) | \
+ FTIM0_NOR_TEADC(0x1) | \
+ FTIM0_NOR_TAVDS(0x0) | \
+ FTIM0_NOR_TEAHC(0xc))
+#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x1c) | \
+ FTIM1_NOR_TRAD_NOR(0xb) | \
+ FTIM1_NOR_TSEQRAD_NOR(0x9))
+#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x1) | \
+ FTIM2_NOR_TCH(0x4) | \
+ FTIM2_NOR_TWPH(0x8) | \
+ FTIM2_NOR_TWP(0x10))
+#define CONFIG_SYS_NOR_FTIM3 0
+#define CONFIG_SYS_IFC_CCR 0x01000000
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE_PHYS }
+
+#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
+#define CONFIG_SYS_WRITE_SWAPPED_DATA
+
+/*
+ * NAND Flash Definitions
+ */
+#define CONFIG_NAND_FSL_IFC
+
+#define CONFIG_SYS_NAND_BASE 0x7e800000
+#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
+
+#define CONFIG_SYS_NAND_CSPR_EXT (0x0)
+#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+ | CSPR_PORT_SIZE_8 \
+ | CSPR_MSEL_NAND \
+ | CSPR_V)
+#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
+#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
+ | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
+ | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
+ | CSOR_NAND_RAL_3 /* RAL = 3 Bytes */ \
+ | CSOR_NAND_PGS_2K /* Page Size = 2K */ \
+ | CSOR_NAND_SPRZ_64 /* Spare size = 64 */ \
+ | CSOR_NAND_PB(64)) /* 64 Pages Per Block */
+
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x7) | \
+ FTIM0_NAND_TWP(0x18) | \
+ FTIM0_NAND_TWCHT(0x7) | \
+ FTIM0_NAND_TWH(0xa))
+#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
+ FTIM1_NAND_TWBE(0x39) | \
+ FTIM1_NAND_TRR(0xe) | \
+ FTIM1_NAND_TRP(0x18))
+#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0xf) | \
+ FTIM2_NAND_TREH(0xa) | \
+ FTIM2_NAND_TWHRE(0x1e))
+#define CONFIG_SYS_NAND_FTIM3 0x0
+
+#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
+
+/*
+ * CPLD
+ */
+#define CONFIG_SYS_CPLD_BASE 0x7fb00000
+#define CPLD_BASE_PHYS CONFIG_SYS_CPLD_BASE
+
+#define CONFIG_SYS_CPLD_CSPR_EXT (0x0)
+#define CONFIG_SYS_CPLD_CSPR (CSPR_PHYS_ADDR(CPLD_BASE_PHYS) | \
+ CSPR_PORT_SIZE_8 | \
+ CSPR_MSEL_GPCM | \
+ CSPR_V)
+#define CONFIG_SYS_CPLD_AMASK IFC_AMASK(64 * 1024)
+#define CONFIG_SYS_CPLD_CSOR (CSOR_NOR_ADM_SHIFT(4) | \
+ CSOR_NOR_NOR_MODE_AVD_NOR | \
+ CSOR_NOR_TRHZ_80)
+
+/* CPLD Timing parameters for IFC GPCM */
+#define CONFIG_SYS_CPLD_FTIM0 (FTIM0_GPCM_TACSE(0xf) | \
+ FTIM0_GPCM_TEADC(0xf) | \
+ FTIM0_GPCM_TEAHC(0xf))
+#define CONFIG_SYS_CPLD_FTIM1 (FTIM1_GPCM_TACO(0xff) | \
+ FTIM1_GPCM_TRAD(0x3f))
+#define CONFIG_SYS_CPLD_FTIM2 (FTIM2_GPCM_TCS(0xf) | \
+ FTIM2_GPCM_TCH(0xf) | \
+ FTIM2_GPCM_TWP(0xff))
+#define CONFIG_SYS_CPLD_FTIM3 0x0
+
+/* IFC Timing Params */
+#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR_CSPR_EXT
+#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR_CSPR
+#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
+
+#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3
+
+#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_CPLD_CSPR_EXT
+#define CONFIG_SYS_CSPR2 CONFIG_SYS_CPLD_CSPR
+#define CONFIG_SYS_AMASK2 CONFIG_SYS_CPLD_AMASK
+#define CONFIG_SYS_CSOR2 CONFIG_SYS_CPLD_CSOR
+#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_CPLD_FTIM0
+#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_CPLD_FTIM1
+#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_CPLD_FTIM2
+#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_CPLD_FTIM3
+
+/* EEPROM */
+#define CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_EEPROM_BUS_NUM 0
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x53
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x200000)
+#define CONFIG_ENV_SECT_SIZE 0x20000
+#define CONFIG_ENV_SIZE 0x20000
+
+#endif /* __LS1043ARDB_H__ */
--
2.1.0.27.g96db324
More information about the U-Boot
mailing list