[U-Boot] [PATCH 1/3] arm: mvebu: a38x: Remove unsupported topologies

Kevin Smith kevin.smith at elecsyscorp.com
Fri Oct 23 19:53:19 CEST 2015


A lot of extra configuration information was left over in the
Marvell serdes and DDR3 initialization code for boards that
U-boot does not support.  Remove this extra config information,
and the concept of fixing up board topologies with information
loaded from an EEPROM.  If this needs to be done, it should be
handled in the board file, not in core code.

Signed-off-by: Kevin Smith <kevin.smith at elecsyscorp.com>
Cc: Stefan Roese <sr at denx.de>
Cc: Dirk Eibach <eibach at gdsys.de>
Cc: Luka Perkov <luka.perkov at sartura.hr>
---
 arch/arm/mach-mvebu/serdes/a38x/Makefile           |    1 -
 .../serdes/a38x/high_speed_env_spec-38x.c          |    1 -
 .../mach-mvebu/serdes/a38x/high_speed_env_spec.c   |   26 -
 .../serdes/a38x/high_speed_topology_spec-38x.c     | 1009 --------------------
 .../serdes/a38x/high_speed_topology_spec.h         |  124 ---
 arch/arm/mach-mvebu/serdes/a38x/seq_exec.c         |    1 -
 arch/arm/mach-mvebu/serdes/a38x/sys_env_lib.c      |  151 ---
 arch/arm/mach-mvebu/serdes/a38x/sys_env_lib.h      |    2 -
 board/Marvell/db-88f6820-gp/db-88f6820-gp.c        |   16 +
 drivers/ddr/marvell/a38x/ddr3_a38x.h               |    5 -
 drivers/ddr/marvell/a38x/ddr3_init.c               |   72 --
 11 files changed, 16 insertions(+), 1392 deletions(-)
 delete mode 100644 arch/arm/mach-mvebu/serdes/a38x/high_speed_topology_spec-38x.c
 delete mode 100644 arch/arm/mach-mvebu/serdes/a38x/high_speed_topology_spec.h

diff --git a/arch/arm/mach-mvebu/serdes/a38x/Makefile b/arch/arm/mach-mvebu/serdes/a38x/Makefile
index 1503da8..83b3c0f 100644
--- a/arch/arm/mach-mvebu/serdes/a38x/Makefile
+++ b/arch/arm/mach-mvebu/serdes/a38x/Makefile
@@ -5,6 +5,5 @@
 obj-$(CONFIG_SPL_BUILD)	= ctrl_pex.o
 obj-$(CONFIG_SPL_BUILD)	+= high_speed_env_spec.o
 obj-$(CONFIG_SPL_BUILD)	+= high_speed_env_spec-38x.o
-obj-$(CONFIG_SPL_BUILD)	+= high_speed_topology_spec-38x.o
 obj-$(CONFIG_SPL_BUILD)	+= seq_exec.o
 obj-$(CONFIG_SPL_BUILD)	+= sys_env_lib.o
diff --git a/arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec-38x.c b/arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec-38x.c
index 5ff8567..104e7e8 100644
--- a/arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec-38x.c
+++ b/arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec-38x.c
@@ -5,7 +5,6 @@
  */
 
 #include <common.h>
-#include <i2c.h>
 #include <spl.h>
 #include <asm/io.h>
 #include <asm/arch/cpu.h>
diff --git a/arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec.c b/arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec.c
index 23af769..c95231b 100644
--- a/arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec.c
+++ b/arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec.c
@@ -5,14 +5,12 @@
  */
 
 #include <common.h>
-#include <i2c.h>
 #include <spl.h>
 #include <asm/io.h>
 #include <asm/arch/cpu.h>
 #include <asm/arch/soc.h>
 
 #include "high_speed_env_spec.h"
-#include "high_speed_topology_spec.h"
 #include "sys_env_lib.h"
 #include "ctrl_pex.h"
 
@@ -1364,27 +1362,6 @@ enum serdes_seq serdes_type_and_speed_to_speed_seq(enum serdes_type serdes_type,
 	return seq_id;
 }
 
-/*
- * This is the weak default function for the Marvell evaluation or
- * development boarrds. Like the DB-88F6820-GP and others.
- * Custom boards should define this function in their board
- * code (board directory). And overwrite this default function
- * with this custom specific code.
- */
-__weak int hws_board_topology_load(struct serdes_map *serdes_map_array)
-{
-	u32 board_id = mv_board_id_get();
-	u32 board_id_index = mv_board_id_index_get(board_id);
-
-	DEBUG_INIT_FULL_S("\n### hws_board_topology_load ###\n");
-	/* getting board topology according to the board id */
-	DEBUG_INIT_FULL_S("Getting board topology according to the board id\n");
-
-	CHECK_STATUS(load_topology_func_arr[board_id_index] (serdes_map_array));
-
-	return MV_OK;
-}
-
 void print_topology_details(struct serdes_map *serdes_map_array)
 {
 	u32 lane_num;
@@ -1448,9 +1425,6 @@ int serdes_phy_config(void)
 		return MV_FAIL;
 	}
 
-	/* I2C init */
-	i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
-
 	/* Board topology load */
 	DEBUG_INIT_FULL_S
 	    ("ctrl_high_speed_serdes_phy_config: Loading board topology..\n");
diff --git a/arch/arm/mach-mvebu/serdes/a38x/high_speed_topology_spec-38x.c b/arch/arm/mach-mvebu/serdes/a38x/high_speed_topology_spec-38x.c
deleted file mode 100644
index 5f2c3eb..0000000
--- a/arch/arm/mach-mvebu/serdes/a38x/high_speed_topology_spec-38x.c
+++ /dev/null
@@ -1,1009 +0,0 @@
-/*
- * Copyright (C) Marvell International Ltd. and its affiliates
- *
- * SPDX-License-Identifier:	GPL-2.0
- */
-
-#include <common.h>
-#include <i2c.h>
-#include <spl.h>
-#include <asm/io.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/soc.h>
-
-#include "high_speed_topology_spec.h"
-#include "sys_env_lib.h"
-
-#ifdef CONFIG_CUSTOMER_BOARD_SUPPORT
-/*
- * This is an example implementation for this custom board
- * specific function
- */
-static struct serdes_map custom_board_topology_config[] = {
-	/* Customer Board Topology - reference from Marvell DB-GP board */
-	{PEX0, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
-	{SATA0, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
-	{SATA1, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
-	{SATA3, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
-	{SATA2, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
-	{USB3_HOST1, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0}
-};
-
-int hws_board_topology_load(struct serdes_map *serdes_map_array)
-{
-	serdes_map_array = custom_board_topology_config;
-}
-#endif
-
-load_topology_func_ptr load_topology_func_arr[] = {
-	load_topology_rd,	/* RD NAS */
-	load_topology_db,	/* 6820 DB-BP (A38x) */
-	load_topology_rd,	/* RD AP */
-	load_topology_db_ap,	/* DB AP */
-	load_topology_db_gp,	/* DB GP */
-	load_topology_db_381,	/* 6821 DB-BP (A381) */
-	load_topology_db_amc,	/* DB-AMC */
-};
-
-/*****************************************/
-/** Load topology - Marvell 380 DB - BP **/
-/*****************************************/
-/* Configuration options */
-struct serdes_map db_config_default[MAX_SERDES_LANES] = {
-	{SATA0, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
-	{PEX0, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
-	{PEX1, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
-	{SATA3, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
-	{USB3_HOST0, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
-	{USB3_HOST1, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0}
-};
-
-struct serdes_map db_config_slm1363_c[MAX_SERDES_LANES] = {
-	{PEX0, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
-	{DEFAULT_SERDES, LAST_SERDES_SPEED, SERDES_DEFAULT_MODE, 0, 0},
-	{PEX1, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
-	{PEX3, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
-	{SATA2, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
-	{DEFAULT_SERDES, LAST_SERDES_SPEED, SERDES_DEFAULT_MODE, 0, 0},
-};
-
-struct serdes_map db_config_slm1363_d[MAX_SERDES_LANES] = {
-	{PEX0, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X4, 0, 0},
-	{PEX1, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X4, 0, 0},
-	{PEX2, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X4, 0, 0},
-	{PEX3, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X4, 0, 0},
-	{USB3_HOST0, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
-	{USB3_HOST1, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0}
-};
-
-struct serdes_map db_config_slm1363_e[MAX_SERDES_LANES] = {
-	{PEX0, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
-	{USB3_HOST0, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
-	{SATA1, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
-	{USB3_HOST1, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
-	{DEFAULT_SERDES, LAST_SERDES_SPEED, SERDES_DEFAULT_MODE, 0, 0},
-	{SATA2, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0}
-};
-
-struct serdes_map db_config_slm1363_f[MAX_SERDES_LANES] = {
-	{PEX0, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
-	{DEFAULT_SERDES, LAST_SERDES_SPEED, SERDES_DEFAULT_MODE, 0, 0},
-	{PEX1, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
-	{PEX3, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
-	{SATA2, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
-	{USB3_HOST1, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0}
-};
-
-struct serdes_map db_config_slm1364_d[MAX_SERDES_LANES] = {
-	{DEFAULT_SERDES, LAST_SERDES_SPEED, SERDES_DEFAULT_MODE, 0, 0},
-	{SGMII0, SERDES_SPEED_3_125_GBPS, SERDES_DEFAULT_MODE, 0, 0},
-	{DEFAULT_SERDES, LAST_SERDES_SPEED, SERDES_DEFAULT_MODE, 0, 0},
-	{DEFAULT_SERDES, LAST_SERDES_SPEED, SERDES_DEFAULT_MODE, 0, 0},
-	{SGMII1, SERDES_SPEED_3_125_GBPS, SERDES_DEFAULT_MODE, 0, 0},
-	{SGMII2, SERDES_SPEED_3_125_GBPS, SERDES_DEFAULT_MODE, 0, 0}
-};
-
-struct serdes_map db_config_slm1364_e[MAX_SERDES_LANES] = {
-	{SGMII0, SERDES_SPEED_3_125_GBPS, SERDES_DEFAULT_MODE, 0, 0},
-	{SGMII1, SERDES_SPEED_3_125_GBPS, SERDES_DEFAULT_MODE, 0, 0},
-	{DEFAULT_SERDES, LAST_SERDES_SPEED, SERDES_DEFAULT_MODE, 0, 0},
-	{SGMII2, SERDES_SPEED_3_125_GBPS, SERDES_DEFAULT_MODE, 0, 0},
-	{DEFAULT_SERDES, LAST_SERDES_SPEED, SERDES_DEFAULT_MODE, 0, 0},
-	{PEX2, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0}
-};
-
-struct serdes_map db_config_slm1364_f[MAX_SERDES_LANES] = {
-	{SGMII0, SERDES_SPEED_3_125_GBPS, SERDES_DEFAULT_MODE, 0, 0},
-	{DEFAULT_SERDES, LAST_SERDES_SPEED, SERDES_DEFAULT_MODE, 0, 0},
-	{SGMII1, SERDES_SPEED_3_125_GBPS, SERDES_DEFAULT_MODE, 0, 0},
-	{SGMII2, SERDES_SPEED_3_125_GBPS, SERDES_DEFAULT_MODE, 0, 0},
-	{DEFAULT_SERDES, LAST_SERDES_SPEED, SERDES_DEFAULT_MODE, 0, 0},
-	{PEX2, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0}
-};
-
-/*************************************************************************/
-/** The following structs are mapping for DB board 'SatR' configuration **/
-/*************************************************************************/
-struct serdes_map db_satr_config_lane1[SATR_DB_LANE1_MAX_OPTIONS] = {
-	/* 0 */ {DEFAULT_SERDES, LAST_SERDES_SPEED, SERDES_DEFAULT_MODE, 0,
-		 0},
-	/* 1 */ {PEX0, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
-	/* 2 */ {SATA0, SERDES_SPEED_3_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
-	/* 3 */ {SGMII0, SERDES_SPEED_3_125_GBPS, SERDES_DEFAULT_MODE, 0,
-		 0},
-	/* 4 */ {SGMII1, SERDES_SPEED_3_125_GBPS, SERDES_DEFAULT_MODE, 0,
-		 0},
-	/* 5 */ {USB3_HOST0, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0,
-		 0},
-	/* 6 */ {QSGMII, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0}
-};
-
-struct serdes_map db_satr_config_lane2[SATR_DB_LANE2_MAX_OPTIONS] = {
-	/* 0 */ {DEFAULT_SERDES, LAST_SERDES_SPEED, SERDES_DEFAULT_MODE, 0,
-		 0},
-	/* 1 */ {PEX1, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
-	/* 2 */ {SATA1, SERDES_SPEED_3_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
-	/* 3 */ {SGMII1, SERDES_SPEED_3_125_GBPS, SERDES_DEFAULT_MODE, 0,
-		 0}
-};
-
-/*******************************************************/
-/* Configuration options DB ****************************/
-/* mapping from TWSI address data to configuration map */
-/*******************************************************/
-struct serdes_map *topology_config_db[] = {
-	db_config_slm1363_c,
-	db_config_slm1363_d,
-	db_config_slm1363_e,
-	db_config_slm1363_f,
-	db_config_slm1364_d,
-	db_config_slm1364_e,
-	db_config_slm1364_f,
-	db_config_default
-};
-
-/*************************************/
-/** Load topology - Marvell DB - AP **/
-/*************************************/
-struct serdes_map db_ap_config_default[MAX_SERDES_LANES] = {
-	/* 0 */ {PEX0, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
-	/* 1 */ {SGMII1, SERDES_SPEED_3_125_GBPS, SERDES_DEFAULT_MODE, 0,
-		 0},
-	/* 2 */ {PEX1, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
-	/* 3 */ {SGMII2, SERDES_SPEED_3_125_GBPS, SERDES_DEFAULT_MODE, 0,
-		 0},
-	/* 4 */ {USB3_HOST0, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0,
-		 0},
-	/* 5 */ {PEX2, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0}
-};
-
-/*************************************/
-/** Load topology - Marvell DB - GP **/
-/*************************************/
-struct serdes_map db_gp_config_default[MAX_SERDES_LANES] = {
-	/* 0 */ {PEX0, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
-	/* 1 */ {SATA0, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
-	/* 2 */ {SATA1, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
-	/* 3 */ {SATA3, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
-	/* 4 */ {SATA2, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
-	/* 5 */ {USB3_HOST1, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0,
-		 0}
-};
-
-struct serdes_map db_amc_config_default[MAX_SERDES_LANES] = {
-	/* 0 */ {PEX0, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X4, 0, 0},
-	/* 1 */ {PEX1, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X4, 0, 0},
-	/* 2 */ {PEX2, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X4, 0, 0},
-	/* 3 */ {PEX3, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X4, 0, 0},
-	/* 4 */ {SGMII1, SERDES_SPEED_3_125_GBPS, SERDES_DEFAULT_MODE, 0,
-		 0},
-	/* 5 */ {SGMII2, SERDES_SPEED_3_125_GBPS, SERDES_DEFAULT_MODE, 0,
-		 0},
-};
-
-/*****************************************/
-/** Load topology - Marvell 381 DB - BP **/
-/*****************************************/
-/* Configuration options */
-struct serdes_map db381_config_default[MAX_SERDES_LANES] = {
-	{SATA0, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 1, 1},
-	{PEX0, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
-	{PEX1, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
-	{USB3_HOST1, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0}
-};
-
-struct serdes_map db_config_slm1427[MAX_SERDES_LANES] = {
-	{SATA0, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 1, 1},
-	{PEX0, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 1, 1},
-	{SATA1, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 1, 1},
-	{USB3_HOST1, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 1, 1}
-};
-
-struct serdes_map db_config_slm1426[MAX_SERDES_LANES] = {
-	{SATA0, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 1, 1},
-	{USB3_HOST0, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 1, 1},
-	{SATA1, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 1, 1},
-	{SGMII2, SERDES_SPEED_3_125_GBPS, SERDES_DEFAULT_MODE, 1, 1}
-};
-
-/*
- * this array must be aligned with enum topology_config_db381 enum,
- * every update to this array requires update to enum topology_config_db381
- * enum
- */
-struct serdes_map *topology_config_db_381[] = {
-	db_config_slm1427,
-	db_config_slm1426,
-	db381_config_default,
-};
-
-u8 topology_config_db_mode_get(void)
-{
-	u8 mode;
-
-	DEBUG_INIT_FULL_S("\n### topology_config_db_mode_get ###\n");
-
-	/* Default - return DB_CONFIG_DEFAULT */
-
-	if (!i2c_read(DB_GET_MODE_SLM1363_ADDR, 0, 1, &mode, 1)) {
-		switch (mode & 0xf) {
-		case 0xc:
-			DEBUG_INIT_S("\nInit DB board SLM 1363 C topology\n");
-			return DB_CONFIG_SLM1363_C;
-		case 0xd:
-			DEBUG_INIT_S("\nInit DB board SLM 1363 D topology\n");
-			return DB_CONFIG_SLM1363_D;
-		case 0xe:
-			DEBUG_INIT_S("\nInit DB board SLM 1363 E topology\n");
-			return DB_CONFIG_SLM1363_E;
-		case 0xf:
-			DEBUG_INIT_S("\nInit DB board SLM 1363 F topology\n");
-			return DB_CONFIG_SLM1363_F;
-		default:	/* not the right module */
-			break;
-		}
-	}
-
-	/* SLM1364 Module */
-	if (i2c_read(DB_GET_MODE_SLM1364_ADDR, 0, 1, &mode, 1)) {
-		DEBUG_INIT_S("\nInit DB board default topology\n");
-		return DB_CONFIG_DEFAULT;
-	}
-
-	switch (mode & 0xf) {
-	case 0xd:
-		DEBUG_INIT_S("\nInit DB board SLM 1364 D topology\n");
-		return DB_CONFIG_SLM1364_D;
-	case 0xe:
-		DEBUG_INIT_S("\nInit DB board SLM 1364 E topology\n");
-		return DB_CONFIG_SLM1364_E;
-	case 0xf:
-		DEBUG_INIT_S("\nInit DB board SLM 1364 F topology\n");
-		return DB_CONFIG_SLM1364_F;
-	default:		/* Default configuration */
-		DEBUG_INIT_S("\nInit DB board default topology\n");
-		return DB_CONFIG_DEFAULT;
-	}
-}
-
-u8 topology_config_db_381_mode_get(void)
-{
-	u8 mode;
-
-	DEBUG_INIT_FULL_S("\n### topology_config_db_381_mode_get ###\n");
-
-	if (!i2c_read(DB381_GET_MODE_SLM1426_1427_ADDR, 0, 2, &mode, 1)) {
-		switch (mode & 0xf) {
-		case 0x1:
-			DEBUG_INIT_S("\nInit DB-381 board SLM 1427 topology\n");
-			return DB_CONFIG_SLM1427;
-		case 0x2:
-			DEBUG_INIT_S("\nInit DB-381 board SLM 1426 topology\n");
-			return DB_CONFIG_SLM1426;
-		default:	/* not the right module */
-			break;
-		}
-	}
-
-	/* in case not detected any supported module, use default topology */
-	DEBUG_INIT_S("\nInit DB-381 board default topology\n");
-	return DB_381_CONFIG_DEFAULT;
-}
-
-/*
- * Read SatR field 'sgmiispeed' and update lane topology SGMII entries
- * speed setup
- */
-int update_topology_sgmii_speed(struct serdes_map *serdes_map_array)
-{
-	u32 serdes_type, lane_num;
-	u8 config_val;
-
-	/* Update SGMII speed settings by 'sgmiispeed' SatR value */
-	for (lane_num = 0; lane_num < hws_serdes_get_max_lane(); lane_num++) {
-		serdes_type = serdes_map_array[lane_num].serdes_type;
-		/*Read SatR configuration for SGMII speed */
-		if ((serdes_type == SGMII0) || (serdes_type == SGMII1) ||
-		    (serdes_type == SGMII2)) {
-			/* Read SatR 'sgmiispeed' value */
-			if (i2c_read(EEPROM_I2C_ADDR, 0, 2, &config_val, 1)) {
-				printf("%s: TWSI Read of 'sgmiispeed' failed\n",
-				       __func__);
-				return MV_FAIL;
-			}
-
-			if (0 == (config_val & 0x40)) {
-				serdes_map_array[lane_num].serdes_speed =
-					SERDES_SPEED_1_25_GBPS;
-			} else {
-				serdes_map_array[lane_num].serdes_speed =
-					SERDES_SPEED_3_125_GBPS;
-			}
-		}
-	}
-	return MV_OK;
-}
-
-struct serdes_map default_lane = {
-	DEFAULT_SERDES, LAST_SERDES_SPEED, SERDES_DEFAULT_MODE
-};
-int is_custom_topology = 0;	/* indicate user of non-default topology */
-
-/*
- * Read SatR fields (dbserdes1/2 , gpserdes1/2/5) and update lane
- * topology accordingly
- */
-int update_topology_satr(struct serdes_map *serdes_map_array)
-{
-	u8 config_val, lane_select, i;
-	u32 board_id = mv_board_id_get();
-
-	switch (board_id) {
-	case DB_68XX_ID:	/* read 'dbserdes1' & 'dbserdes2' */
-	case DB_BP_6821_ID:
-		if (i2c_read(EEPROM_I2C_ADDR, 1, 2, &config_val, 1)) {
-			printf("%s: TWSI Read of 'dbserdes1/2' failed\n",
-			       __func__);
-			return MV_FAIL;
-		}
-
-		/* Lane #1 */
-		lane_select = (config_val & SATR_DB_LANE1_CFG_MASK) >>
-			SATR_DB_LANE1_CFG_OFFSET;
-		if (lane_select >= SATR_DB_LANE1_MAX_OPTIONS) {
-			printf("\n\%s: Error: invalid value for SatR field 'dbserdes1' (%x)\n",
-			       __func__, lane_select);
-			printf("\t_skipping Topology update (run 'SatR write default')\n");
-			return MV_FAIL;
-		}
-
-		/*
-		 * If modified default serdes_type for lane#1, update
-		 * topology and mark it as custom
-		 */
-		if (serdes_map_array[1].serdes_type !=
-		    db_satr_config_lane1[lane_select].serdes_type) {
-			serdes_map_array[1] = db_satr_config_lane1[lane_select];
-			is_custom_topology = 1;
-			/* DB 381/2 board has inverted SerDes polarity */
-			if (board_id == DB_BP_6821_ID)
-				serdes_map_array[1].swap_rx =
-					serdes_map_array[1].swap_tx = 1;
-		}
-
-		/* Lane #2 */
-		lane_select = (config_val & SATR_DB_LANE2_CFG_MASK) >>
-			SATR_DB_LANE2_CFG_OFFSET;
-		if (lane_select >= SATR_DB_LANE2_MAX_OPTIONS) {
-			printf("\n\%s: Error: invalid value for SatR field 'dbserdes2' (%x)\n",
-			       __func__, lane_select);
-			printf("\t_skipping Topology update (run 'SatR write default')\n");
-			return MV_FAIL;
-		}
-
-		/*
-		 * If modified default serdes_type for lane at 2, update
-		 * topology and mark it as custom
-		 */
-		if (serdes_map_array[2].serdes_type !=
-		    db_satr_config_lane2[lane_select].serdes_type) {
-			serdes_map_array[2] = db_satr_config_lane2[lane_select];
-			is_custom_topology = 1;
-			/* DB 381/2 board has inverted SerDes polarity */
-			if (board_id == DB_BP_6821_ID)
-				serdes_map_array[2].swap_rx =
-					serdes_map_array[2].swap_tx = 1;
-		}
-
-		if (is_custom_topology == 1) {
-			/*
-			 * Check for conflicts with detected lane #1 and
-			 * lane #2 (Disable conflicted lanes)
-			 */
-			for (i = 0; i < hws_serdes_get_max_lane(); i++) {
-				if (i != 1 && serdes_map_array[1].serdes_type ==
-				    serdes_map_array[i].serdes_type) {
-					printf("\t_lane #%d Type conflicts with Lane #1 (Lane #%d disabled)\n",
-					       i, i);
-					serdes_map_array[i] =
-						db_satr_config_lane1[0];
-				}
-
-				if (i != 2 &&
-				    serdes_map_array[2].serdes_type ==
-				    serdes_map_array[i].serdes_type) {
-					printf("\t_lane #%d Type conflicts with Lane #2 (Lane #%d disabled)\n",
-					       i, i);
-					serdes_map_array[i] =
-						db_satr_config_lane1[0];
-				}
-			}
-		}
-
-		break;		/* case DB_68XX_ID */
-	case DB_GP_68XX_ID:	/* read 'gpserdes1' & 'gpserdes2' */
-		if (i2c_read(EEPROM_I2C_ADDR, 2, 2, &config_val, 1)) {
-			printf("%s: TWSI Read of 'gpserdes1/2' failed\n",
-			       __func__);
-			return MV_FAIL;
-		}
-
-		/*
-		 * Lane #1:
-		 * lane_select = 0 --> SATA0,
-		 * lane_select = 1 --> PCIe0 (mini PCIe)
-		 */
-		lane_select = (config_val & SATR_GP_LANE1_CFG_MASK) >>
-			SATR_GP_LANE1_CFG_OFFSET;
-		if (lane_select == 1) {
-			serdes_map_array[1].serdes_mode = PEX0;
-			serdes_map_array[1].serdes_speed = SERDES_SPEED_5_GBPS;
-			serdes_map_array[1].serdes_type = PEX_ROOT_COMPLEX_X1;
-			/*
-			 * If lane 1 is set to PCIe0 --> disable PCIe0
-			 * on lane 0
-			 */
-			serdes_map_array[0] = default_lane;
-			/* indicate user of non-default topology */
-			is_custom_topology = 1;
-		}
-		printf("Lane 1 detection: %s\n",
-		       lane_select ? "PCIe0 (mini PCIe)" : "SATA0");
-
-		/*
-		 * Lane #2:
-		 * lane_select = 0 --> SATA1,
-		 * lane_select = 1 --> PCIe1 (mini PCIe)
-		 */
-		lane_select = (config_val & SATR_GP_LANE2_CFG_MASK) >>
-			SATR_GP_LANE2_CFG_OFFSET;
-		if (lane_select == 1) {
-			serdes_map_array[2].serdes_type = PEX1;
-			serdes_map_array[2].serdes_speed = SERDES_SPEED_5_GBPS;
-			serdes_map_array[2].serdes_mode = PEX_ROOT_COMPLEX_X1;
-			/* indicate user of non-default topology */
-			is_custom_topology = 1;
-		}
-		printf("Lane 2 detection: %s\n",
-		       lane_select ? "PCIe1 (mini PCIe)" : "SATA1");
-		break;		/* case DB_GP_68XX_ID */
-	}
-
-	if (is_custom_topology)
-		printf("\nDetected custom SerDes topology (to restore default run 'SatR write default')\n\n");
-
-	return MV_OK;
-}
-
-/*
- * hws_update_device_toplogy
- * DESCRIPTION: Update the default board topology for specific device Id
- * INPUT:
- *	topology_config_ptr - pointer to the Serdes mapping
- *	topology_mode - topology mode (index)
- * OUTPUT: None
- * RRETURNS:
- *	MV_OK - if updating the board topology success
- *	MV_BAD_PARAM - if the input parameter is wrong
- */
-int hws_update_device_toplogy(struct serdes_map *topology_config_ptr,
-			      enum topology_config_db topology_mode)
-{
-	u32 dev_id = sys_env_device_id_get();
-	u32 board_id = mv_board_id_get();
-
-	switch (topology_mode) {
-	case DB_CONFIG_DEFAULT:
-		switch (dev_id) {
-		case MV_6810:
-			/*
-			 * DB-AP : default for Lane3=SGMII2 -->
-			 * 6810 supports only 2 SGMII interfaces:
-			 * lane 3 disabled
-			 */
-			if (board_id == DB_AP_68XX_ID) {
-				printf("Device 6810 supports only 2 SGMII interfaces: SGMII-2 @ lane3 disabled\n");
-				topology_config_ptr[3] = default_lane;
-			}
-
-			/*
-			 * 6810 has only 4 SerDes and the forth one is
-			 * Serdes number 5 (i.e. Serdes 4 is not connected),
-			 * therefore we need to copy SerDes 5 configuration
-			 * to SerDes 4
-			 */
-			printf("Device 6810 does not supports SerDes Lane #4: replaced topology entry with lane #5\n");
-			topology_config_ptr[4] = topology_config_ptr[5];
-
-			/*
-			 * No break between cases since the 1st
-			 * 6820 limitation apply on 6810
-			 */
-		case MV_6820:
-			/*
-			 * DB-GP & DB-BP: default for Lane3=SATA3 -->
-			 * 6810/20 supports only 2 SATA interfaces:
-			 * lane 3 disabled
-			 */
-			if ((board_id == DB_68XX_ID) ||
-			    (board_id == DB_GP_68XX_ID)) {
-				printf("Device 6810/20 supports only 2 SATA interfaces: SATA Port 3 @ lane3 disabled\n");
-				topology_config_ptr[3] = default_lane;
-			}
-			/*
-			 * DB-GP on 6820 only: default for Lane4=SATA2
-			 * --> 6820 supports only 2 SATA interfaces:
-			 * lane 3 disabled
-			 */
-			if (board_id == DB_GP_68XX_ID && dev_id == MV_6820) {
-				printf("Device 6820 supports only 2 SATA interfaces: SATA Port 2 @ lane4 disabled\n");
-				topology_config_ptr[4] = default_lane;
-			}
-			break;
-		default:
-			break;
-		}
-		break;
-
-	default:
-		printf("sys_env_update_device_toplogy: selected topology is not supported by this routine\n");
-		break;
-	}
-
-	return MV_OK;
-}
-
-int load_topology_db_381(struct serdes_map *serdes_map_array)
-{
-	u32 lane_num;
-	u8 topology_mode;
-	struct serdes_map *topology_config_ptr;
-	u8 twsi_data;
-	u8 usb3_host0_or_device = 0, usb3_host1_or_device = 0;
-
-	printf("\nInitialize DB-88F6821-BP board topology\n");
-
-	/* Getting the relevant topology mode (index) */
-	topology_mode = topology_config_db_381_mode_get();
-	topology_config_ptr = topology_config_db_381[topology_mode];
-
-	/* Read USB3.0 mode: HOST/DEVICE */
-	if (load_topology_usb_mode_get(&twsi_data) == MV_OK) {
-		usb3_host0_or_device = (twsi_data & 0x1);
-		/* Only one USB3 device is enabled */
-		if (usb3_host0_or_device == 0)
-			usb3_host1_or_device = ((twsi_data >> 1) & 0x1);
-	}
-
-	/* Updating the topology map */
-	for (lane_num = 0; lane_num < hws_serdes_get_max_lane(); lane_num++) {
-		serdes_map_array[lane_num].serdes_mode =
-			topology_config_ptr[lane_num].serdes_mode;
-		serdes_map_array[lane_num].serdes_speed =
-			topology_config_ptr[lane_num].serdes_speed;
-		serdes_map_array[lane_num].serdes_type =
-			topology_config_ptr[lane_num].serdes_type;
-		serdes_map_array[lane_num].swap_rx =
-			topology_config_ptr[lane_num].swap_rx;
-		serdes_map_array[lane_num].swap_tx =
-			topology_config_ptr[lane_num].swap_tx;
-
-		/* Update USB3 device if needed */
-		if (usb3_host0_or_device == 1 &&
-		    serdes_map_array[lane_num].serdes_type == USB3_HOST0)
-			serdes_map_array[lane_num].serdes_type = USB3_DEVICE;
-
-		if (usb3_host1_or_device == 1 &&
-		    serdes_map_array[lane_num].serdes_type == USB3_HOST1)
-			serdes_map_array[lane_num].serdes_type = USB3_DEVICE;
-	}
-
-	/* If not detected any SerDes Site module, read 'SatR' lane setup */
-	if (topology_mode == DB_381_CONFIG_DEFAULT)
-		update_topology_satr(serdes_map_array);
-
-	/* update 'sgmiispeed' settings */
-	update_topology_sgmii_speed(serdes_map_array);
-
-	return MV_OK;
-}
-
-int load_topology_db(struct serdes_map *serdes_map_array)
-{
-	u32 lane_num;
-	u8 topology_mode;
-	struct serdes_map *topology_config_ptr;
-	u8 twsi_data;
-	u8 usb3_host0_or_device = 0, usb3_host1_or_device = 0;
-
-	printf("\nInitialize DB-88F6820-BP board topology\n");
-
-	/* Getting the relevant topology mode (index) */
-	topology_mode = topology_config_db_mode_get();
-
-	if (topology_mode == DB_NO_TOPOLOGY)
-		topology_mode = DB_CONFIG_DEFAULT;
-
-	topology_config_ptr = topology_config_db[topology_mode];
-
-	/* Update the default board topology device flavours */
-	CHECK_STATUS(hws_update_device_toplogy
-		     (topology_config_ptr, topology_mode));
-
-	/* Read USB3.0 mode: HOST/DEVICE */
-	if (load_topology_usb_mode_get(&twsi_data) == MV_OK) {
-		usb3_host0_or_device = (twsi_data & 0x1);
-		/* Only one USB3 device is enabled */
-		if (usb3_host0_or_device == 0)
-			usb3_host1_or_device = ((twsi_data >> 1) & 0x1);
-	}
-
-	/* Updating the topology map */
-	for (lane_num = 0; lane_num < hws_serdes_get_max_lane(); lane_num++) {
-		serdes_map_array[lane_num].serdes_mode =
-			topology_config_ptr[lane_num].serdes_mode;
-		serdes_map_array[lane_num].serdes_speed =
-			topology_config_ptr[lane_num].serdes_speed;
-		serdes_map_array[lane_num].serdes_type =
-			topology_config_ptr[lane_num].serdes_type;
-		serdes_map_array[lane_num].swap_rx =
-			topology_config_ptr[lane_num].swap_rx;
-		serdes_map_array[lane_num].swap_tx =
-			topology_config_ptr[lane_num].swap_tx;
-
-		/*
-		 * Update USB3 device if needed - relevant for
-		 * lane 3,4,5 only
-		 */
-		if (lane_num >= 3) {
-			if ((serdes_map_array[lane_num].serdes_type ==
-			     USB3_HOST0) && (usb3_host0_or_device == 1))
-				serdes_map_array[lane_num].serdes_type =
-					USB3_DEVICE;
-
-			if ((serdes_map_array[lane_num].serdes_type ==
-			     USB3_HOST1) && (usb3_host1_or_device == 1))
-				serdes_map_array[lane_num].serdes_type =
-					USB3_DEVICE;
-		}
-	}
-
-	/* If not detected any SerDes Site module, read 'SatR' lane setup */
-	if (topology_mode == DB_CONFIG_DEFAULT)
-		update_topology_satr(serdes_map_array);
-
-	/* update 'sgmiispeed' settings */
-	update_topology_sgmii_speed(serdes_map_array);
-
-	return MV_OK;
-}
-
-int load_topology_db_ap(struct serdes_map *serdes_map_array)
-{
-	u32 lane_num;
-	struct serdes_map *topology_config_ptr;
-
-	DEBUG_INIT_FULL_S("\n### load_topology_db_ap ###\n");
-
-	printf("\nInitialize DB-AP board topology\n");
-	topology_config_ptr = db_ap_config_default;
-
-	/* Update the default board topology device flavours */
-	CHECK_STATUS(hws_update_device_toplogy
-		     (topology_config_ptr, DB_CONFIG_DEFAULT));
-
-	/* Updating the topology map */
-	for (lane_num = 0; lane_num < hws_serdes_get_max_lane(); lane_num++) {
-		serdes_map_array[lane_num].serdes_mode =
-			topology_config_ptr[lane_num].serdes_mode;
-		serdes_map_array[lane_num].serdes_speed =
-			topology_config_ptr[lane_num].serdes_speed;
-		serdes_map_array[lane_num].serdes_type =
-			topology_config_ptr[lane_num].serdes_type;
-		serdes_map_array[lane_num].swap_rx =
-			topology_config_ptr[lane_num].swap_rx;
-		serdes_map_array[lane_num].swap_tx =
-			topology_config_ptr[lane_num].swap_tx;
-	}
-
-	update_topology_sgmii_speed(serdes_map_array);
-
-	return MV_OK;
-}
-
-int load_topology_db_gp(struct serdes_map *serdes_map_array)
-{
-	u32 lane_num;
-	struct serdes_map *topology_config_ptr;
-	int is_sgmii = 0;
-
-	DEBUG_INIT_FULL_S("\n### load_topology_db_gp ###\n");
-
-	topology_config_ptr = db_gp_config_default;
-
-	printf("\nInitialize DB-GP board topology\n");
-
-	/* check S at R: if lane 5 is USB3 or SGMII */
-	if (load_topology_rd_sgmii_usb(&is_sgmii) != MV_OK)
-		printf("%s: TWSI Read failed - Loading Default Topology\n",
-		       __func__);
-	else {
-		topology_config_ptr[5].serdes_type =
-			is_sgmii ? SGMII2 : USB3_HOST1;
-		topology_config_ptr[5].serdes_speed = is_sgmii ?
-			SERDES_SPEED_3_125_GBPS : SERDES_SPEED_5_GBPS;
-		topology_config_ptr[5].serdes_mode = SERDES_DEFAULT_MODE;
-	}
-
-	/* Update the default board topology device flavours */
-	CHECK_STATUS(hws_update_device_toplogy
-		     (topology_config_ptr, DB_CONFIG_DEFAULT));
-
-	/* Updating the topology map */
-	for (lane_num = 0; lane_num < hws_serdes_get_max_lane(); lane_num++) {
-		serdes_map_array[lane_num].serdes_mode =
-			topology_config_ptr[lane_num].serdes_mode;
-		serdes_map_array[lane_num].serdes_speed =
-			topology_config_ptr[lane_num].serdes_speed;
-		serdes_map_array[lane_num].serdes_type =
-			topology_config_ptr[lane_num].serdes_type;
-		serdes_map_array[lane_num].swap_rx =
-			topology_config_ptr[lane_num].swap_rx;
-		serdes_map_array[lane_num].swap_tx =
-			topology_config_ptr[lane_num].swap_tx;
-	}
-
-	/*
-	 * Update 'gpserdes1/2/3' lane configuration , and 'sgmiispeed'
-	 * for SGMII lanes
-	 */
-	update_topology_satr(serdes_map_array);
-	update_topology_sgmii_speed(serdes_map_array);
-
-	return MV_OK;
-}
-
-int load_topology_db_amc(struct serdes_map *serdes_map_array)
-{
-	u32 lane_num;
-	struct serdes_map *topology_config_ptr;
-
-	DEBUG_INIT_FULL_S("\n### load_topology_db_amc ###\n");
-
-	printf("\nInitialize DB-AMC board topology\n");
-	topology_config_ptr = db_amc_config_default;
-
-	/* Update the default board topology device flavours */
-	CHECK_STATUS(hws_update_device_toplogy
-		     (topology_config_ptr, DB_CONFIG_DEFAULT));
-
-	/* Updating the topology map */
-	for (lane_num = 0; lane_num < hws_serdes_get_max_lane(); lane_num++) {
-		serdes_map_array[lane_num].serdes_mode =
-			topology_config_ptr[lane_num].serdes_mode;
-		serdes_map_array[lane_num].serdes_speed =
-			topology_config_ptr[lane_num].serdes_speed;
-		serdes_map_array[lane_num].serdes_type =
-			topology_config_ptr[lane_num].serdes_type;
-		serdes_map_array[lane_num].swap_rx =
-			topology_config_ptr[lane_num].swap_rx;
-		serdes_map_array[lane_num].swap_tx =
-			topology_config_ptr[lane_num].swap_tx;
-	}
-
-	update_topology_sgmii_speed(serdes_map_array);
-
-	return MV_OK;
-}
-
-int load_topology_rd(struct serdes_map *serdes_map_array)
-{
-	u8 mode;
-
-	DEBUG_INIT_FULL_S("\n### load_topology_rd ###\n");
-
-	DEBUG_INIT_S("\nInit RD board ");
-
-	/* Reading mode */
-	DEBUG_INIT_FULL_S("load_topology_rd: getting mode\n");
-	if (i2c_read(EEPROM_I2C_ADDR, 0, 2, &mode, 1)) {
-		DEBUG_INIT_S("load_topology_rd: TWSI Read failed\n");
-		return MV_FAIL;
-	}
-
-	/* Updating the topology map */
-	DEBUG_INIT_FULL_S("load_topology_rd: Loading board topology details\n");
-
-	/* RD mode: 0 = NAS, 1 = AP */
-	if (((mode >> 1) & 0x1) == 0) {
-		CHECK_STATUS(load_topology_rd_nas(serdes_map_array));
-	} else {
-		CHECK_STATUS(load_topology_rd_ap(serdes_map_array));
-	}
-
-	update_topology_sgmii_speed(serdes_map_array);
-
-	return MV_OK;
-}
-
-int load_topology_rd_nas(struct serdes_map *serdes_map_array)
-{
-	int is_sgmii = 0;
-	u32 i;
-
-	DEBUG_INIT_S("\nInit RD NAS topology ");
-
-	/* check if lane 4 is USB3 or SGMII */
-	if (load_topology_rd_sgmii_usb(&is_sgmii) != MV_OK) {
-		DEBUG_INIT_S("load_topology_rd NAS: TWSI Read failed\n");
-		return MV_FAIL;
-	}
-
-	/* Lane 0 */
-	serdes_map_array[0].serdes_type = PEX0;
-	serdes_map_array[0].serdes_speed = SERDES_SPEED_5_GBPS;
-	serdes_map_array[0].serdes_mode = PEX_ROOT_COMPLEX_X1;
-
-	/* Lane 1 */
-	serdes_map_array[1].serdes_type = SATA0;
-	serdes_map_array[1].serdes_speed = SERDES_SPEED_3_GBPS;
-	serdes_map_array[1].serdes_mode = SERDES_DEFAULT_MODE;
-
-	/* Lane 2 */
-	serdes_map_array[2].serdes_type = SATA1;
-	serdes_map_array[2].serdes_speed = SERDES_SPEED_3_GBPS;
-	serdes_map_array[2].serdes_mode = SERDES_DEFAULT_MODE;
-
-	/* Lane 3 */
-	serdes_map_array[3].serdes_type = SATA3;
-	serdes_map_array[3].serdes_speed = SERDES_SPEED_3_GBPS;
-	serdes_map_array[3].serdes_mode = SERDES_DEFAULT_MODE;
-
-	/* Lane 4 */
-	if (is_sgmii == 1) {
-		DEBUG_INIT_S("Serdes Lane 4 is SGMII\n");
-		serdes_map_array[4].serdes_type = SGMII1;
-		serdes_map_array[4].serdes_speed = SERDES_SPEED_3_125_GBPS;
-		serdes_map_array[4].serdes_mode = SERDES_DEFAULT_MODE;
-	} else {
-		DEBUG_INIT_S("Serdes Lane 4 is USB3\n");
-		serdes_map_array[4].serdes_type = USB3_HOST0;
-		serdes_map_array[4].serdes_speed = SERDES_SPEED_5_GBPS;
-		serdes_map_array[4].serdes_mode = SERDES_DEFAULT_MODE;
-	}
-
-	/* Lane 5 */
-	serdes_map_array[5].serdes_type = SATA2;
-	serdes_map_array[5].serdes_speed = SERDES_SPEED_3_GBPS;
-	serdes_map_array[5].serdes_mode = SERDES_DEFAULT_MODE;
-
-	/* init swap configuration */
-	for (i = 0; i <= 5; i++) {
-		serdes_map_array[i].swap_rx = 0;
-		serdes_map_array[i].swap_tx = 0;
-	}
-
-	return MV_OK;
-}
-
-int load_topology_rd_ap(struct serdes_map *serdes_map_array)
-{
-	int is_sgmii = 0;
-	u32 i;
-
-	DEBUG_INIT_S("\nInit RD AP topology ");
-
-	/* check if lane 4 is USB3 or SGMII */
-	if (load_topology_rd_sgmii_usb(&is_sgmii) != MV_OK) {
-		DEBUG_INIT_S("load_topology_rd AP: TWSI Read failed\n");
-		return MV_FAIL;
-	}
-
-	/* Lane 0 */
-	serdes_map_array[0].serdes_type = DEFAULT_SERDES;
-	serdes_map_array[0].serdes_speed = LAST_SERDES_SPEED;
-	serdes_map_array[0].serdes_mode = SERDES_DEFAULT_MODE;
-
-	/* Lane 1 */
-	serdes_map_array[1].serdes_type = PEX0;
-	serdes_map_array[1].serdes_speed = SERDES_SPEED_5_GBPS;
-	serdes_map_array[1].serdes_mode = PEX_ROOT_COMPLEX_X1;
-
-	/* Lane 2 */
-	serdes_map_array[2].serdes_type = PEX1;
-	serdes_map_array[2].serdes_speed = SERDES_SPEED_5_GBPS;
-	serdes_map_array[2].serdes_mode = PEX_ROOT_COMPLEX_X1;
-
-	/* Lane 3 */
-	serdes_map_array[3].serdes_type = SATA3;
-	serdes_map_array[3].serdes_speed = SERDES_SPEED_3_GBPS;
-	serdes_map_array[3].serdes_mode = SERDES_DEFAULT_MODE;
-
-	/* Lane 4 */
-	if (is_sgmii == 1) {
-		DEBUG_INIT_S("Serdes Lane 4 is SGMII\n");
-		serdes_map_array[4].serdes_type = SGMII1;
-		serdes_map_array[4].serdes_speed = SERDES_SPEED_3_125_GBPS;
-		serdes_map_array[4].serdes_mode = SERDES_DEFAULT_MODE;
-	} else {
-		DEBUG_INIT_S("Serdes Lane 4 is USB3\n");
-		serdes_map_array[4].serdes_type = USB3_HOST0;
-		serdes_map_array[4].serdes_speed = SERDES_SPEED_5_GBPS;
-		serdes_map_array[4].serdes_mode = SERDES_DEFAULT_MODE;
-	}
-
-	/* Lane 5 */
-	serdes_map_array[5].serdes_type = SATA2;
-	serdes_map_array[5].serdes_speed = SERDES_SPEED_3_GBPS;
-	serdes_map_array[5].serdes_mode = SERDES_DEFAULT_MODE;
-
-	/* init swap configuration */
-	for (i = 0; i <= 5; i++) {
-		serdes_map_array[i].swap_rx = 0;
-		serdes_map_array[i].swap_tx = 0;
-	}
-
-	return MV_OK;
-}
-
-int load_topology_rd_sgmii_usb(int *is_sgmii)
-{
-	u8 mode;
-
-	/*
-	 * DB-GP board: Device 6810 supports only 2 GbE ports:
-	 * SGMII2 not supported (USE USB3 Host instead)
-	 */
-	if (sys_env_device_id_get() == MV_6810) {
-		printf("Device 6810 supports only 2 GbE ports: SGMII-2 @ lane5 disabled (setting USB3.0 H1 instead)\n");
-		*is_sgmii = 0;
-		return MV_OK;
-	}
-
-	if (!i2c_read(RD_GET_MODE_ADDR, 1, 2, &mode, 1)) {
-		*is_sgmii = ((mode >> 2) & 0x1);
-	} else {
-		/* else use the default - USB3 */
-		*is_sgmii = 0;
-	}
-
-	if (*is_sgmii)
-		is_custom_topology = 1;
-
-	printf("Lane 5 detection: %s\n",
-	       *is_sgmii ? "SGMII2" : "USB3.0 Host Port 1");
-
-	return MV_OK;
-}
-
-/*
- * 'usb3port0'/'usb3port1' fields are located in EEPROM,
- * at 3rd byte(offset=2), bit 0:1 (respectively)
- */
-int load_topology_usb_mode_get(u8 *twsi_data)
-{
-	if (!i2c_read(EEPROM_I2C_ADDR, 2, 2, twsi_data, 1))
-		return MV_OK;
-
-	return MV_ERROR;
-}
diff --git a/arch/arm/mach-mvebu/serdes/a38x/high_speed_topology_spec.h b/arch/arm/mach-mvebu/serdes/a38x/high_speed_topology_spec.h
deleted file mode 100644
index 3cfb1c7..0000000
--- a/arch/arm/mach-mvebu/serdes/a38x/high_speed_topology_spec.h
+++ /dev/null
@@ -1,124 +0,0 @@
-/*
- * Copyright (C) Marvell International Ltd. and its affiliates
- *
- * SPDX-License-Identifier:	GPL-2.0
- */
-
-#ifndef _HIGHSPEED_TOPOLOGY_SPEC_H
-#define _HIGHSPEED_TOPOLOGY_SPEC_H
-
-#include "high_speed_env_spec.h"
-
-/* Topology map options for the DB_A38X_BP board */
-enum topology_config_db {
-	DB_CONFIG_SLM1363_C,
-	DB_CONFIG_SLM1363_D,
-	DB_CONFIG_SLM1363_E,
-	DB_CONFIG_SLM1363_F,
-	DB_CONFIG_SLM1364_D,
-	DB_CONFIG_SLM1364_E,
-	DB_CONFIG_SLM1364_F,
-	DB_CONFIG_DEFAULT,
-	DB_NO_TOPOLOGY
-};
-
-/*
- * this enum must be aligned with topology_config_db_381 array,
- * every update to this enum requires update to topology_config_db_381
- * array
- */
-enum topology_config_db381 {
-	DB_CONFIG_SLM1427,	/* enum for db_config_slm1427 */
-	DB_CONFIG_SLM1426,	/* enum for db_config_slm1426 */
-	DB_381_CONFIG_DEFAULT,
-	DB_381_NO_TOPOLOGY
-};
-
-/* A generic function pointer for loading the board topology map */
-typedef int (*load_topology_func_ptr)(struct serdes_map *serdes_map_array);
-
-extern load_topology_func_ptr load_topology_func_arr[];
-
-/*
- * topology_config_db_mode_get -
- *
- * DESCRIPTION:		Gets the relevant topology mode (index).
- *			for load_topology_db use only.
- * INPUT:		None.
- * OUTPUT:		None.
- * RETURNS:		the topology mode
- */
-u8 topology_config_db_mode_get(void);
-
-/*
- * load_topology_xxx -
- *
- * DESCRIPTION:		Loads the board topology for the XXX board
- * INPUT:		serdes_map_array - The struct that will contain
- *			the board topology map
- * OUTPUT:		The board topology map.
- * RETURNS:		MV_OK   for success
- *			MV_FAIL	for failure (a wrong topology mode was read
- *			from the board)
- */
-
-/* load_topology_db - Loads the board topology for DB Board */
-int load_topology_db(struct serdes_map *serdes_map_array);
-
-/* load_topology_rd - Loads the board topology for RD Board */
-int load_topology_rd(struct serdes_map *serdes_map_array);
-
-/* load_topology_rd_nas - Loads the board topology for RD NAS Board */
-int load_topology_rd_nas(struct serdes_map *serdes_map_array);
-
-/* load_topology_rd_ap - Loads the board topology for RD Ap Board */
-int load_topology_rd_ap(struct serdes_map *serdes_map_array);
-
-/* load_topology_db_ap - Loads the board topology for DB-AP Board */
-int load_topology_db_ap(struct serdes_map *serdes_map_array);
-
-/* load_topology_db_gp - Loads the board topology for DB GP Board */
-int load_topology_db_gp(struct serdes_map *serdes_map_array);
-
-/* load_topology_db_381 - Loads the board topology for 381 DB-BP Board */
-int load_topology_db_381(struct serdes_map *serdes_map_array);
-
-/* load_topology_db_amc - Loads the board topology for DB-AMC Board */
-int load_topology_db_amc(struct serdes_map *serdes_map_array);
-
-/*
- * hws_update_device_toplogy
- * DESCRIPTION: Update the default board topology for specific device Id
- * INPUT:
- *	topology_config_ptr - pointer to the Serdes mapping
- *	topology_mode - topology mode (index)
- * OUTPUT: None
- * RRETURNS:
- *	MV_OK - if updating the board topology success
- *	MV_BAD_PARAM - if the input parameter is wrong
- */
-int hws_update_device_toplogy(struct serdes_map *topology_config_ptr,
-			      enum topology_config_db topology_mode);
-
-/*
- * load_topology_rd_sgmii_usb -
- *
- * DESCRIPTION:			For RD board check if lane 4 is USB3 or SGMII
- * INPUT:			None
- * OUTPUT:			is_sgmii - return 1 if lane 4 is SGMII
- *				return 0 if lane 4 is USB.
- * RETURNS:			MV_OK for success
- */
-int load_topology_rd_sgmii_usb(int *is_sgmii);
-
-/*
- * load_topology_usb_mode_get -
- *
- * DESCRIPTION:			For DB board check if USB3.0 mode
- * INPUT:			None
- * OUTPUT:			twsi_data - return data read from S at R via I2C
- * RETURNS:			MV_OK for success
- */
-int load_topology_usb_mode_get(u8 *twsi_data);
-
-#endif /* _HIGHSPEED_TOPOLOGY_SPEC_H */
diff --git a/arch/arm/mach-mvebu/serdes/a38x/seq_exec.c b/arch/arm/mach-mvebu/serdes/a38x/seq_exec.c
index ee2305b..905b907 100644
--- a/arch/arm/mach-mvebu/serdes/a38x/seq_exec.c
+++ b/arch/arm/mach-mvebu/serdes/a38x/seq_exec.c
@@ -5,7 +5,6 @@
  */
 
 #include <common.h>
-#include <i2c.h>
 #include <spl.h>
 #include <asm/io.h>
 #include <asm/arch/cpu.h>
diff --git a/arch/arm/mach-mvebu/serdes/a38x/sys_env_lib.c b/arch/arm/mach-mvebu/serdes/a38x/sys_env_lib.c
index efd3873..49d704a 100644
--- a/arch/arm/mach-mvebu/serdes/a38x/sys_env_lib.c
+++ b/arch/arm/mach-mvebu/serdes/a38x/sys_env_lib.c
@@ -5,7 +5,6 @@
  */
 
 #include <common.h>
-#include <i2c.h>
 #include <spl.h>
 #include <asm/io.h>
 #include <asm/arch/cpu.h>
@@ -236,153 +235,3 @@ u32 sys_env_device_id_get(void)
 
 	return g_dev_id;
 }
-
-#ifdef MV_DDR_TOPOLOGY_UPDATE_FROM_TWSI
-/*
-* sys_env_get_topology_update_info
-* DESCRIPTION: Read TWSI fields to update DDR topology structure
-* INPUT: None
-* OUTPUT: None, 0 means no topology update
-* RETURN:
-*       Bit mask of changes topology features
-*/
-#ifdef CONFIG_ARMADA_39X
-u32 sys_env_get_topology_update_info(
-	struct topology_update_info *tui)
-{
-	/* Set 16/32 bit configuration*/
-	tui->update_width = 1;
-	tui->width = TOPOLOGY_UPDATE_WIDTH_32BIT;
-
-#ifdef CONFIG_DDR3
-	if (1 == sys_env_config_get(MV_CONFIG_DDR_BUSWIDTH)) {
-		/* 16bit */
-		tui->width = TOPOLOGY_UPDATE_WIDTH_16BIT;
-	} else {
-		/* 32bit */
-		tui->width = TOPOLOGY_UPDATE_WIDTH_32BIT;
-	}
-#endif
-
-	/* Set ECC/no ECC bit configuration */
-	tui->update_ecc = 1;
-	if (0 == sys_env_config_get(MV_CONFIG_DDR_ECC_EN)) {
-		/* NO ECC */
-		tui->ecc = TOPOLOGY_UPDATE_ECC_OFF;
-	} else {
-		/* ECC */
-		tui->ecc = TOPOLOGY_UPDATE_ECC_ON;
-	}
-
-	tui->update_ecc_pup3_mode = 1;
-	tui->ecc_pup_mode_offset = TOPOLOGY_UPDATE_ECC_OFFSET_PUP4;
-
-	return MV_OK;
-}
-#else /*CONFIG_ARMADA_38X*/
-u32 sys_env_get_topology_update_info(
-	struct topology_update_info *tui)
-{
-	u8 config_val;
-	u8 ecc_mode[A38X_MV_MAX_MARVELL_BOARD_ID -
-		    A38X_MARVELL_BOARD_ID_BASE][5] = TOPOLOGY_UPDATE;
-	u8 board_id = mv_board_id_get();
-	int ret;
-
-	board_id = mv_board_id_index_get(board_id);
-	ret = i2c_read(EEPROM_I2C_ADDR, 0, 2, &config_val, 1);
-	if (ret) {
-		DEBUG_INIT_S("sys_env_get_topology_update_info: TWSI Read failed\n");
-		return 0;
-	}
-
-	/* Set 16/32 bit configuration */
-	if ((0 == (config_val & DDR_SATR_CONFIG_MASK_WIDTH)) ||
-	    (ecc_mode[board_id][TOPOLOGY_UPDATE_32BIT] == 0)) {
-		/* 16bit by SatR of 32bit mode not supported for the board */
-		if ((ecc_mode[board_id][TOPOLOGY_UPDATE_16BIT] != 0)) {
-			tui->update_width = 1;
-			tui->width = TOPOLOGY_UPDATE_WIDTH_16BIT;
-		}
-	} else {
-		/* 32bit */
-		if ((ecc_mode[board_id][TOPOLOGY_UPDATE_32BIT] != 0)) {
-			tui->update_width = 1;
-			tui->width = TOPOLOGY_UPDATE_WIDTH_32BIT;
-		}
-	}
-
-	/* Set ECC/no ECC bit configuration */
-	if (0 == (config_val & DDR_SATR_CONFIG_MASK_ECC)) {
-		/* NO ECC */
-		tui->update_ecc = 1;
-		tui->ecc = TOPOLOGY_UPDATE_ECC_OFF;
-	} else {
-		/* ECC */
-		if ((ecc_mode[board_id][TOPOLOGY_UPDATE_32BIT_ECC] != 0) ||
-		    (ecc_mode[board_id][TOPOLOGY_UPDATE_16BIT_ECC] != 0) ||
-		    (ecc_mode[board_id][TOPOLOGY_UPDATE_16BIT_ECC_PUP3] != 0)) {
-			tui->update_ecc = 1;
-			tui->ecc = TOPOLOGY_UPDATE_ECC_ON;
-		}
-	}
-
-	/* Set ECC pup bit configuration */
-	if (0 == (config_val & DDR_SATR_CONFIG_MASK_ECC_PUP)) {
-		/* PUP3 */
-		/*
-		 * Check if PUP3 configuration allowed, if not -
-		 * force Pup4 with warning message
-		 */
-		if ((ecc_mode[board_id][TOPOLOGY_UPDATE_16BIT_ECC_PUP3] != 0)) {
-			if (tui->width == TOPOLOGY_UPDATE_WIDTH_16BIT) {
-				tui->update_ecc_pup3_mode = 1;
-				tui->ecc_pup_mode_offset =
-					TOPOLOGY_UPDATE_ECC_OFFSET_PUP3;
-			} else {
-				if ((ecc_mode[board_id][TOPOLOGY_UPDATE_32BIT_ECC] != 0)) {
-					printf("DDR Topology Update: ECC PUP3 not valid for 32bit mode, force ECC in PUP4\n");
-					tui->update_ecc_pup3_mode = 1;
-					tui->ecc_pup_mode_offset =
-						TOPOLOGY_UPDATE_ECC_OFFSET_PUP4;
-				}
-			}
-		} else {
-			if (ecc_mode[board_id][TOPOLOGY_UPDATE_16BIT_ECC] !=
-			    0) {
-				printf("DDR Topology Update: ECC on PUP3 not supported, force ECC on PUP4\n");
-				tui->update_ecc_pup3_mode = 1;
-				tui->ecc_pup_mode_offset =
-					TOPOLOGY_UPDATE_ECC_OFFSET_PUP4;
-			}
-		}
-	} else {
-		/* PUP4 */
-		if ((ecc_mode[board_id][TOPOLOGY_UPDATE_32BIT_ECC] != 0) ||
-		    (ecc_mode[board_id][TOPOLOGY_UPDATE_16BIT_ECC] != 0)) {
-			tui->update_ecc_pup3_mode = 1;
-			tui->ecc_pup_mode_offset =
-				TOPOLOGY_UPDATE_ECC_OFFSET_PUP4;
-		}
-	}
-
-	/*
-	 * Check for forbidden ECC mode,
-	 * if by default width and pup selection set 32bit ECC mode and this
-	 * mode not supported for the board - config 16bit with ECC on PUP3
-	 */
-	if ((tui->ecc == TOPOLOGY_UPDATE_ECC_ON) &&
-	    (tui->width == TOPOLOGY_UPDATE_WIDTH_32BIT)) {
-		if (ecc_mode[board_id][TOPOLOGY_UPDATE_32BIT_ECC] == 0) {
-			printf("DDR Topology Update: 32bit mode with ECC not allowed on this board, forced  16bit with ECC on PUP3\n");
-			tui->width = TOPOLOGY_UPDATE_WIDTH_16BIT;
-			tui->update_ecc_pup3_mode = 1;
-			tui->ecc_pup_mode_offset =
-				TOPOLOGY_UPDATE_ECC_OFFSET_PUP3;
-		}
-	}
-
-	return MV_OK;
-}
-#endif /* CONFIG_ARMADA_38X */
-#endif /* MV_DDR_TOPOLOGY_UPDATE_FROM_TWSI */
diff --git a/arch/arm/mach-mvebu/serdes/a38x/sys_env_lib.h b/arch/arm/mach-mvebu/serdes/a38x/sys_env_lib.h
index 3e5373c..a413c51 100644
--- a/arch/arm/mach-mvebu/serdes/a38x/sys_env_lib.h
+++ b/arch/arm/mach-mvebu/serdes/a38x/sys_env_lib.h
@@ -364,8 +364,6 @@ u8 sys_env_device_rev_get(void);
 u32 sys_env_device_id_get(void);
 u16 sys_env_model_get(void);
 struct dlb_config *sys_env_dlb_config_ptr_get(void);
-u32 sys_env_get_topology_update_info(
-	struct topology_update_info *topology_update_info);
 u32 sys_env_get_cs_ena_from_reg(void);
 
 #endif /* _SYS_ENV_LIB_H */
diff --git a/board/Marvell/db-88f6820-gp/db-88f6820-gp.c b/board/Marvell/db-88f6820-gp/db-88f6820-gp.c
index 84ca55c..384d002 100644
--- a/board/Marvell/db-88f6820-gp/db-88f6820-gp.c
+++ b/board/Marvell/db-88f6820-gp/db-88f6820-gp.c
@@ -13,6 +13,7 @@
 #include <asm/arch/soc.h>
 
 #include "../drivers/ddr/marvell/a38x/ddr3_a38x_topology.h"
+#include <../serdes/a38x/high_speed_env_spec.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -55,6 +56,21 @@ static struct marvell_io_exp io_exp[] = {
 	{ 0x21, 3, 0xC0 }  /* Output Data, register#1 */
 };
 
+static struct serdes_map board_serdes_map[] = {
+	{PEX0, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0},
+	{SATA0, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+	{SATA1, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+	{SATA3, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+	{SATA2, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+	{USB3_HOST1, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0}
+};
+
+int hws_board_topology_load(struct serdes_map *serdes_map_array)
+{
+	memcpy(serdes_map_array, board_serdes_map, sizeof(board_serdes_map));
+	return 0;
+}
+
 /*
  * Define the DDR layout / topology here in the board file. This will
  * be used by the DDR3 init code in the SPL U-Boot version to configure
diff --git a/drivers/ddr/marvell/a38x/ddr3_a38x.h b/drivers/ddr/marvell/a38x/ddr3_a38x.h
index 49621bc..1ed5174 100644
--- a/drivers/ddr/marvell/a38x/ddr3_a38x.h
+++ b/drivers/ddr/marvell/a38x/ddr3_a38x.h
@@ -12,11 +12,6 @@
 
 #include "ddr3_hws_hw_training_def.h"
 
-/* Allow topolgy update from board TWSI device*/
-#if !defined(CONFIG_CUSTOMER_BOARD_SUPPORT)
-#define MV_DDR_TOPOLOGY_UPDATE_FROM_TWSI
-#endif
-
 #define ECC_SUPPORT
 
 /* right now, we're not supporting this in mainline */
diff --git a/drivers/ddr/marvell/a38x/ddr3_init.c b/drivers/ddr/marvell/a38x/ddr3_init.c
index d6ed8e0..556f877 100644
--- a/drivers/ddr/marvell/a38x/ddr3_init.c
+++ b/drivers/ddr/marvell/a38x/ddr3_init.c
@@ -96,7 +96,6 @@ u8 generic_init_controller = 1;
 static u32 ddr3_get_static_ddr_mode(void);
 #endif
 static int ddr3_hws_tune_training_params(u8 dev_num);
-static int ddr3_update_topology_map(struct hws_topology_map *topology_map);
 
 /* device revision */
 #define DEV_VERSION_ID_REG		0x1823c
@@ -383,14 +382,6 @@ int ddr3_init(void)
 	}
 #endif
 
-	/* Load topology for New Training IP */
-	status = ddr3_load_topology_map();
-	if (MV_OK != status) {
-		printf("%s Training Sequence topology load - FAILED\n",
-		       ddr_type);
-		return status;
-	}
-
 	/* Tune training algo paramteres */
 	status = ddr3_hws_tune_training_params(0);
 	if (MV_OK != status)
@@ -539,27 +530,6 @@ u32 ddr3_get_cs_num_from_reg(void)
 	return cs_count;
 }
 
-/*
- * Name:     ddr3_load_topology_map
- * Desc:
- * Args:
- * Notes:
- * Returns:
- */
-int ddr3_load_topology_map(void)
-{
-	struct hws_topology_map *tm = ddr3_get_topology_map();
-
-#if defined(MV_DDR_TOPOLOGY_UPDATE_FROM_TWSI)
-	/* Update topology data */
-	if (MV_OK != ddr3_update_topology_map(tm)) {
-		DEBUG_INIT_FULL_S("Failed update of DDR3 Topology map\n");
-	}
-#endif
-
-	return MV_OK;
-}
-
 void get_target_freq(u32 freq_mode, u32 *ddr_freq, u32 *hclk_ps)
 {
 	u32 tmp, hclk = 200;
@@ -781,48 +751,6 @@ int ddr3_calc_mem_cs_size(u32 cs, u32 *cs_size)
 	return MV_OK;
 }
 
-#if defined(MV_DDR_TOPOLOGY_UPDATE_FROM_TWSI)
-/*
- * Name:     ddr3_update_topology_map
- * Desc:
- * Args:
- * Notes: Update topology map by Sat_r values
- * Returns:
- */
-static int ddr3_update_topology_map(struct hws_topology_map *tm)
-{
-	struct topology_update_info topology_update_info;
-
-	topology_update_info.update_width = 0;
-	topology_update_info.update_ecc = 0;
-	topology_update_info.update_ecc_pup3_mode = 0;
-	sys_env_get_topology_update_info(&topology_update_info);
-	if (topology_update_info.update_width) {
-		tm->bus_act_mask &=
-		    ~(TOPOLOGY_UPDATE_WIDTH_32BIT_MASK);
-		if (topology_update_info.width == TOPOLOGY_UPDATE_WIDTH_16BIT)
-			tm->bus_act_mask =
-			    TOPOLOGY_UPDATE_WIDTH_16BIT_MASK;
-		else
-			tm->bus_act_mask =
-			    TOPOLOGY_UPDATE_WIDTH_32BIT_MASK;
-	}
-
-	if (topology_update_info.update_ecc) {
-		if (topology_update_info.ecc == TOPOLOGY_UPDATE_ECC_OFF) {
-			tm->bus_act_mask &=
-			    ~(1 << topology_update_info.ecc_pup_mode_offset);
-		} else {
-			tm->bus_act_mask |=
-			    topology_update_info.
-			    ecc << topology_update_info.ecc_pup_mode_offset;
-		}
-	}
-
-	return MV_OK;
-}
-#endif
-
 /*
  * Name:     ddr3_hws_tune_training_params
  * Desc:
-- 
2.4.6


More information about the U-Boot mailing list