[U-Boot] [PATCH v2] arm: atmel: Add SAMA5D2 Xplained board
Yang, Wenyou
Wenyou.Yang at atmel.com
Tue Oct 27 07:48:36 CET 2015
Hi Shen Bo,
Thank you very much for your review.
> -----Original Message-----
> From: Bo Shen [mailto:voice.shen at gmail.com]
> Sent: 2015年10月27日 11:09
> To: Yang, Wenyou; andreas.devel at googlemail.com
> Cc: U-Boot Mailing List
> Subject: Re: [U-Boot] [PATCH v2] arm: atmel: Add SAMA5D2 Xplained board
>
> Hi Wenyou,
> + Andreas
>
> On 10/27/2015 08:59 AM, Wenyou Yang wrote:
> > The board supports following features:
> > - Boot media support: SD card/e.MMC/SPI flash,
> > - Support LCD display (optional, disabled by default),
> > - Support ethernet,
> > - Support USB mass storage.
> >
> > Signed-off-by: Wenyou Yang <wenyou.yang at atmel.com>
> > ---
> > The patch is based on the following patches sent in mailing list.
> > [PATCH] gpio: atmel: Add the PIO4 driver support
> > [PATCH] arm: at91: Change the Chip ID registers' addresses
> > [PATCH v3] mmc: atmel: Add atmel sdhci support
> > [PATCH v2] arm: at91: clock: Add the generated clock support
> >
> > Changes in v2:
> > 1./ re-order SAMA5D2 statements alphabetically.
> > 2./ remove redundant "Unknown CPU type".
> > 3./ rework sama5d2's macros.
> > 4./ remove some #ifdef before functions.
> > 5./ move CONFIG_CMD_SF to Kconfig.
> > 6./ remove NAND macros from config file.
> > 7./ CONFIG_BOOTCOMMAND for sf uses defines in at91-sama5_common.h.
> >
> > arch/arm/mach-at91/Kconfig | 5 +
> > arch/arm/mach-at91/armv7/Makefile | 1 +
> > arch/arm/mach-at91/armv7/sama5d2_devices.c | 60 +++++
> > arch/arm/mach-at91/include/mach/at91_pmc.h | 9 +-
> > arch/arm/mach-at91/include/mach/atmel_usba_udc.h | 3 +-
> > arch/arm/mach-at91/include/mach/hardware.h | 2 +
> > arch/arm/mach-at91/include/mach/sama5d2.h | 224
> +++++++++++++++++
> > board/atmel/sama5d2_xplained/Kconfig | 15 ++
> > board/atmel/sama5d2_xplained/MAINTAINERS | 7 +
> > board/atmel/sama5d2_xplained/Makefile | 8 +
> > board/atmel/sama5d2_xplained/sama5d2_xplained.c | 282
> ++++++++++++++++++++++
> > configs/sama5d2_xplained_mmc_defconfig | 11 +
> > configs/sama5d2_xplained_spiflash_defconfig | 11 +
> > include/configs/sama5d2_xplained.h | 126 ++++++++++
> > 14 files changed, 758 insertions(+), 6 deletions(-)
> > create mode 100644 arch/arm/mach-at91/armv7/sama5d2_devices.c
> > create mode 100644 arch/arm/mach-at91/include/mach/sama5d2.h
> > create mode 100644 board/atmel/sama5d2_xplained/Kconfig
> > create mode 100644 board/atmel/sama5d2_xplained/MAINTAINERS
> > create mode 100644 board/atmel/sama5d2_xplained/Makefile
> > create mode 100644 board/atmel/sama5d2_xplained/sama5d2_xplained.c
> > create mode 100644 configs/sama5d2_xplained_mmc_defconfig
> > create mode 100644 configs/sama5d2_xplained_spiflash_defconfig
> > create mode 100644 include/configs/sama5d2_xplained.h
> >
> > diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
> > index fdaf328..c333647 100644
> > --- a/arch/arm/mach-at91/Kconfig
> > +++ b/arch/arm/mach-at91/Kconfig
> > @@ -71,6 +71,10 @@ config TARGET_AT91SAM9X5EK
> > select CPU_ARM926EJS
> > select SUPPORT_SPL
> >
> > +config TARGET_SAMA5D2_XPLAINED
> > + bool "SAMA5D2 Xplained board"
> > + select CPU_V7
> > +
> > config TARGET_SAMA5D3_XPLAINED
> > bool "SAMA5D3 Xplained board"
> > select CPU_V7
> > @@ -123,6 +127,7 @@ source "board/atmel/at91sam9m10g45ek/Kconfig"
> > source "board/atmel/at91sam9n12ek/Kconfig"
> > source "board/atmel/at91sam9rlek/Kconfig"
> > source "board/atmel/at91sam9x5ek/Kconfig"
> > +source "board/atmel/sama5d2_xplained/Kconfig"
> > source "board/atmel/sama5d3_xplained/Kconfig"
> > source "board/atmel/sama5d3xek/Kconfig"
> > source "board/atmel/sama5d4_xplained/Kconfig"
> > diff --git a/arch/arm/mach-at91/armv7/Makefile
> > b/arch/arm/mach-at91/armv7/Makefile
> > index f4f35a4..9538bc1 100644
> > --- a/arch/arm/mach-at91/armv7/Makefile
> > +++ b/arch/arm/mach-at91/armv7/Makefile
> > @@ -8,6 +8,7 @@
> > # SPDX-License-Identifier: GPL-2.0+
> > #
> >
> > +obj-$(CONFIG_SAMA5D2) += sama5d2_devices.o
> > obj-$(CONFIG_SAMA5D3) += sama5d3_devices.o
> > obj-$(CONFIG_SAMA5D4) += sama5d4_devices.o
> > obj-y += clock.o
> > diff --git a/arch/arm/mach-at91/armv7/sama5d2_devices.c
> > b/arch/arm/mach-at91/armv7/sama5d2_devices.c
> > new file mode 100644
> > index 0000000..26883fc
> > --- /dev/null
> > +++ b/arch/arm/mach-at91/armv7/sama5d2_devices.c
> > @@ -0,0 +1,60 @@
> > +/*
> > + * Copyright (C) 2015 Atmel Corporation
> > + * Wenyou Yang <wenyou.yang at atmel.com>
> > + *
> > + * SPDX-License-Identifier: GPL-2.0+
> > + */
> > +
> > +#include <common.h>
> > +#include <asm/io.h>
> > +#include <asm/arch/at91_pmc.h>
> > +#include <asm/arch/clk.h>
> > +#include <asm/arch/sama5d2.h>
> > +
> > +char *get_cpu_name()
> > +{
> > + unsigned int extension_id = get_extension_chip_id();
> > +
> > + if (cpu_is_sama5d2()) {
> > + switch (extension_id) {
> > + case ARCH_EXID_SAMA5D21CU:
> > + return "SAMA5D21";
> > + case ARCH_EXID_SAMA5D22CU:
> > + return "SAMA5D22-CU";
> > + case ARCH_EXID_SAMA5D22CN:
> > + return "SAMA5D22-CN";
> > + case ARCH_EXID_SAMA5D23CU:
> > + return "SAMA5D23-CU";
> > + case ARCH_EXID_SAMA5D24CX:
> > + return "SAMA5D24-CX";
> > + case ARCH_EXID_SAMA5D24CU:
> > + return "SAMA5D24-CU";
> > + case ARCH_EXID_SAMA5D26CU:
> > + return "SAMA5D26-CU";
> > + case ARCH_EXID_SAMA5D27CU:
> > + return "SAMA5D27-CU";
> > + case ARCH_EXID_SAMA5D27CN:
> > + return "SAMA5D27-CN";
> > + case ARCH_EXID_SAMA5D28CU:
> > + return "SAMA5D28-CU";
> > + case ARCH_EXID_SAMA5D28CN:
> > + return "SAMA5D28-CN";
> > + default:
> > + goto err_exit;
> > + }
> > + }
> > +
> > +err_exit:
> > + return "Unknown CPU type";
> > +}
>
> Can we return directly from default? (I guess when compile it will throw out
> warning message, if so, remove default option).
I don't think the default can be remove in switch-case statement.
>
> > +
> > +#ifdef CONFIG_USB_GADGET_ATMEL_USBA
> > +void at91_udp_hw_init(void)
> > +{
> > + struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
> > +
> > + writel(AT91_PMC_UPLLEN | AT91_PMC_BIASEN, &pmc->uckr);
> > +
> > + at91_periph_clk_enable(ATMEL_ID_UDPHS);
> > +}
> > +#endif
> > diff --git a/arch/arm/mach-at91/include/mach/at91_pmc.h
> > b/arch/arm/mach-at91/include/mach/at91_pmc.h
> > index 8a3fb94..5adaa30 100644
> > --- a/arch/arm/mach-at91/include/mach/at91_pmc.h
> > +++ b/arch/arm/mach-at91/include/mach/at91_pmc.h
> > @@ -78,7 +78,8 @@ typedef struct at91_pmc {
> > #define AT91_PMC_PLLXR_DIV(x) (x & 0xFF)
> > #define AT91_PMC_PLLXR_PLLCOUNT(x) ((x & 0x3F) << 8)
> > #define AT91_PMC_PLLXR_OUT(x) ((x & 0x03) << 14)
> > -#if defined(CONFIG_SAMA5D3) || defined(CONFIG_SAMA5D4)
> > +#if defined(CONFIG_SAMA5D2) || defined(CONFIG_SAMA5D3) || \
> > + defined(CONFIG_SAMA5D4)
> > #define AT91_PMC_PLLXR_MUL(x) ((x & 0x7F) << 18)
> > #else
> > #define AT91_PMC_PLLXR_MUL(x) ((x & 0x7FF) << 16)
> > @@ -97,7 +98,8 @@ typedef struct at91_pmc {
> > #define AT91_PMC_MCKR_CSS_PLLB 0x00000003
> > #define AT91_PMC_MCKR_CSS_MASK 0x00000003
> >
> > -#if defined(CONFIG_SAMA5D3) || defined(CONFIG_SAMA5D4) || \
> > +#if defined(CONFIG_SAMA5D2) || defined(CONFIG_SAMA5D3) || \
> > + defined(CONFIG_SAMA5D4) || \
> > defined(CONFIG_AT91SAM9X5) || defined(CONFIG_AT91SAM9N12)
> > #define AT91_PMC_MCKR_PRES_1 0x00000000
> > #define AT91_PMC_MCKR_PRES_2 0x00000010
> > @@ -127,10 +129,7 @@ typedef struct at91_pmc {
> > #else
> > #define AT91_PMC_MCKR_MDIV_1 0x00000000
> > #define AT91_PMC_MCKR_MDIV_2 0x00000100
> > -#if defined(CONFIG_SAMA5D3) || defined(CONFIG_SAMA5D4) || \
> > - defined(CONFIG_AT91SAM9X5) || defined(CONFIG_AT91SAM9N12)
> > #define AT91_PMC_MCKR_MDIV_3 0x00000300
> > -#endif
> > #define AT91_PMC_MCKR_MDIV_4 0x00000200
> > #define AT91_PMC_MCKR_MDIV_MASK 0x00000300
> > #endif
> > diff --git a/arch/arm/mach-at91/include/mach/atmel_usba_udc.h
> > b/arch/arm/mach-at91/include/mach/atmel_usba_udc.h
> > index 38b5012..46a329b 100644
> > --- a/arch/arm/mach-at91/include/mach/atmel_usba_udc.h
> > +++ b/arch/arm/mach-at91/include/mach/atmel_usba_udc.h
> > @@ -31,7 +31,8 @@ static struct usba_ep_data usba_udc_ep[] = {
> > EP("ep5", 5, 1024, 3, 1, 1),
> > EP("ep6", 6, 1024, 3, 1, 1),
> > };
> > -#elif defined(CONFIG_SAMA5D3) || defined(CONFIG_SAMA5D4)
> > +#elif defined(CONFIG_SAMA5D2) || defined(CONFIG_SAMA5D3) || \
> > + defined(CONFIG_SAMA5D4)
> > static struct usba_ep_data usba_udc_ep[] = {
> > EP("ep0", 0, 64, 1, 0, 0),
> > EP("ep1", 1, 1024, 3, 1, 0),
> > diff --git a/arch/arm/mach-at91/include/mach/hardware.h
> > b/arch/arm/mach-at91/include/mach/hardware.h
> > index ff6b71b..38abfda 100644
> > --- a/arch/arm/mach-at91/include/mach/hardware.h
> > +++ b/arch/arm/mach-at91/include/mach/hardware.h
> > @@ -23,6 +23,8 @@
> > # include <asm/arch/at91sam9g45.h>
> > #elif defined(CONFIG_AT91SAM9N12) || defined(CONFIG_AT91SAM9X5)
> > # include <asm/arch/at91sam9x5.h>
> > +#elif defined(CONFIG_SAMA5D2)
> > +# include <asm/arch/sama5d2.h>
> > #elif defined(CONFIG_SAMA5D3)
> > # include <asm/arch/sama5d3.h>
> > #elif defined(CONFIG_SAMA5D4)
> > diff --git a/arch/arm/mach-at91/include/mach/sama5d2.h
> > b/arch/arm/mach-at91/include/mach/sama5d2.h
> > new file mode 100644
> > index 0000000..200070d
> > --- /dev/null
> > +++ b/arch/arm/mach-at91/include/mach/sama5d2.h
> > @@ -0,0 +1,224 @@
> > +/*
> > + * Chip-specific header file for the SAMA5D2 SoC
> > + *
> > + * Copyright (C) 2015 Atmel
> > + * Wenyou Yang <wenyou.yang at atmel.com>
> > + *
> > + * SPDX-License-Identifier: GPL-2.0+
> > + */
> > +
> > +#ifndef __SAMA5D2_H
> > +#define __SAMA5D2_H
> > +
> > +/*
> > + * defines to be used in other places
>
> s/defines/definition
All changed, more clearly.
>
> > + */
> > +#define CONFIG_AT91FAMILY /* It's a member of AT91 */
> > +
> > +/*
> > + * Peripheral identifiers/interrupts.
> > + */
> > +#define ATMEL_ID_FIQ 0 /* FIQ Interrupt ID */
> > +/* 1 */
> > +#define ATMEL_ID_ARM 2 /* Performance Monitor Unit */
> > +#define ATMEL_ID_PIT 3 /* Periodic Interval Timer Interrupt
> */
> > +#define ATMEL_ID_WDT 4 /* Watchdog Timer Interrupt */
> > +#define ATMEL_ID_GMAC 5 /* Ethernet MAC */
> > +#define ATMEL_ID_XDMAC0 6 /* DMA Controller 0 */
> > +#define ATMEL_ID_XDMAC1 7 /* DMA Controller 1 */
> > +#define ATMEL_ID_ICM 8 /* Integrity Check Monitor */
> > +#define ATMEL_ID_AES 9 /* Advanced Encryption Standard
> */
> > +#define ATMEL_ID_AESB 10 /* AES bridge */
> > +#define ATMEL_ID_TDES 11 /* Triple Data Encryption Standard
> */
> > +#define ATMEL_ID_SHA 12 /* SHA Signature */
> > +#define ATMEL_ID_MPDDRC 13 /* MPDDR Controller */
> > +#define ATMEL_ID_MATRIX1 14 /* H32MX, 32-bit AHB Matrix */
> > +#define ATMEL_ID_MATRIX0 15 /* H64MX, 64-bit AHB Matrix */
> > +#define ATMEL_ID_SECUMOD 16 /* Secure Module */
> > +#define ATMEL_ID_HSMC 17 /* Multi-bit ECC interrupt */
> > +#define ATMEL_ID_PIOA 18 /* Parallel I/O Controller A */
> > +#define ATMEL_ID_FLEXCOM0 19 /* FLEXCOM0 */
> > +#define ATMEL_ID_FLEXCOM1 20 /* FLEXCOM1 */
> > +#define ATMEL_ID_FLEXCOM2 21 /* FLEXCOM2 */
> > +#define ATMEL_ID_FLEXCOM3 22 /* FLEXCOM3 */
> > +#define ATMEL_ID_FLEXCOM4 23 /* FLEXCOM4 */
> > +#define ATMEL_ID_UART0 24 /* UART0 */
> > +#define ATMEL_ID_UART1 25 /* UART1 */
> > +#define ATMEL_ID_UART2 26 /* UART2 */
> > +#define ATMEL_ID_UART3 27 /* UART3 */
> > +#define ATMEL_ID_UART4 28 /* UART4 */
> > +#define ATMEL_ID_TWIHS0 29 /* Two-wire Interface 0 */
> > +#define ATMEL_ID_TWIHS1 30 /* Two-wire Interface 1 */
> > +#define ATMEL_ID_SDMMC0 31 /* Secure Data Memory
> Card Controller 0 */
> > +#define ATMEL_ID_SDMMC1 32 /* Secure Data Memory
> Card Controller 1 */
> > +#define ATMEL_ID_SPI0 33 /* Serial Peripheral Interface 0 */
> > +#define ATMEL_ID_SPI1 34 /* Serial Peripheral Interface 1 */
> > +#define ATMEL_ID_TC0 35 /* Timer Counter 0 (ch.0,1,2) */
> > +#define ATMEL_ID_TC1 36 /* Timer Counter 1 (ch.3,4,5) */
> > +/* 37 */
> > +#define ATMEL_ID_PWM 38 /* PWMController0 (ch. 0,1,2,3) */
> > +/* 39 */
> > +#define ATMEL_ID_ADC 40 /* Touch Screen ADC Controller */
> > +#define ATMEL_ID_UHPHS 41 /* USB Host High Speed */
> > +#define ATMEL_ID_UDPHS 42 /* USB Device High Speed */
> > +#define ATMEL_ID_SSC0 43 /* Serial Synchronous Controller 0
> */
> > +#define ATMEL_ID_SSC1 44 /* Serial Synchronous Controller 1
> */
> > +#define ATMEL_ID_LCDC 45 /* LCD Controller */
> > +#define ATMEL_ID_ISI 46 /* Image Sensor Controller, for
> A5D2, named after ISC */
> > +#define ATMEL_ID_TRNG 47 /* True Random Number
> Generator */
> > +#define ATMEL_ID_PDMIC 48 /* PDM Interface Controller */
> > +#define ATMEL_ID_AIC_IRQ 49 /* IRQ Interrupt ID */
> > +#define ATMEL_ID_SFC 50 /* Fuse Controller */
> > +#define ATMEL_ID_SECURAM 51 /* Secure RAM */
> > +#define ATMEL_ID_QSPI0 52 /* QSPI0 */
> > +#define ATMEL_ID_QSPI1 53 /* QSPI1 */
> > +#define ATMEL_ID_I2SC0 54 /* Inter-IC Sound Controller 0 */
> > +#define ATMEL_ID_I2SC1 55 /* Inter-IC Sound Controller 1 */
> > +#define ATMEL_ID_CAN0_INT0 56 /* MCAN 0 Interrupt0 */
> > +#define ATMEL_ID_CAN1_INT0 57 /* MCAN 1 Interrupt0 */
> > +/* 58 */
> > +#define ATMEL_ID_CLASSD 59 /* Audio Class D Amplifier
> */
> > +#define ATMEL_ID_SFR 60 /* Special Function Register */
> > +#define ATMEL_ID_SAIC 61 /* Secured AIC */
> > +#define ATMEL_ID_AIC 62 /* Advanced Interrupt Controller */
> > +#define ATMEL_ID_L2CC 63 /* L2 Cache Controller */
> > +#define ATMEL_ID_CAN0_INT1 64 /* MCAN 0 Interrupt1 */
> > +#define ATMEL_ID_CAN1_INT1 65 /* MCAN 1 Interrupt1 */
> > +#define ATMEL_ID_GMAC_Q1 66 /* GMAC Queue 1 Interrupt */
> > +#define ATMEL_ID_GMAC_Q2 67 /* GMAC Queue 2 Interrupt */
> > +#define ATMEL_ID_PIOB 68 /* Parallel I/O Controller B */
> > +#define ATMEL_ID_PIOC 69 /* Parallel I/O Controller C */
> > +#define ATMEL_ID_PIOD 70 /* Parallel I/O Controller D */
> > +#define ATMEL_ID_SDMMC0_TIMER 71 /* Secure Data Memory
> Card Controller 0 (TIMER) */
> > +#define ATMEL_ID_SDMMC1_TIMER 72 /* Secure Data Memory
> Card Controller 1 (TIMER) */
> > +/* 73 */
> > +#define ATMEL_ID_SYS 74 /* System Controller Interrupt */
> > +#define ATMEL_ID_ACC 75 /* Analog Comparator */
> > +#define ATMEL_ID_RXLP 76 /* UART Low-Power */
> > +#define ATMEL_ID_SFRBU 77 /* Special Function Register
> BackUp */
> > +#define ATMEL_ID_CHIPID 78 /* Chip ID */
> > +
> > +/*
> > + * User Peripherals physical base addresses.
> > + */
> > +#define ATMEL_BASE_LCDC 0xf0000000
> > +#define ATMEL_BASE_XDMAC1 0xf0004000
> > +#define ATMEL_BASE_MPDDRC 0xf000c000
> > +#define ATMEL_BASE_XDMAC0 0xf0010000
> > +#define ATMEL_BASE_PMC 0xf0014000
> > +#define ATMEL_BASE_QSPI0 0xf0020000
> > +#define ATMEL_BASE_QSPI1 0xf0024000
> > +#define ATMEL_BASE_SPI0 0xf8000000
> > +#define ATMEL_BASE_GMAC 0xf8008000
> > +#define ATMEL_BASE_TC0 0xf800c000
> > +#define ATMEL_BASE_TC1 0xf8010000
> > +#define ATMEL_BASE_HSMC 0xf8014000
> > +#define ATMEL_BASE_UART0 0xf801c000
> > +#define ATMEL_BASE_UART1 0xf8020000
> > +#define ATMEL_BASE_UART2 0xf8024000
> > +#define ATMEL_BASE_TWI0 0xf8028000
> > +#define ATMEL_BASE_SYSC 0xf8048000
> > +#define ATMEL_BASE_SPI1 0xfc000000
> > +#define ATMEL_BASE_UART3 0xfc008000
> > +#define ATMEL_BASE_UART4 0xfc00c000
> > +#define ATMEL_BASE_TWI1 0xfc028000
> > +#define ATMEL_BASE_UDPHS 0xfc02c000
> > +
> > +#define ATMEL_BASE_PIOA 0xfc038000
> > +
> > +#define ATMEL_CHIPID_CIDR 0xfc069000
> > +#define ATMEL_CHIPID_EXID 0xfc069004
> > +
> > +/*
> > + * Address Memory Space
> > + */
> > +#define ATMEL_BASE_DDRCS 0x20000000
> > +#define ATMEL_BASE_QSPI0_AES_MEM 0x90000000
> > +#define ATMEL_BASE_QSPI1_AES_MEM 0x98000000
> > +#define ATMEL_BASE_SDMMC0 0xa0000000
> > +#define ATMEL_BASE_SDMMC1 0xb0000000
> > +#define ATMEL_BASE_QSPI0_MEM 0xd0000000
> > +#define ATMEL_BASE_QSPI1_MEM 0xd8000000
> > +
> > +/*
> > + * Internal Memories
> > + */
> > +#define ATMEL_BASE_UDPHS_FIFO 0x00300000 /* USB Device HS
> controller */
> > +#define ATMEL_BASE_OHCI 0x00400000 /* USB Host
> controller (OHCI) */
> > +#define ATMEL_BASE_EHCI 0x00500000 /* USB Host
> controller (EHCI) */
> > +
> > +/* Other misc defines */
>
> Ditto
>
> > +#define ATMEL_BASE_PMECC (ATMEL_BASE_HSMC + 0x70)
> > +#define ATMEL_BASE_PMERRLOC (ATMEL_BASE_HSMC + 0x500)
> > +
> > +#define ATMEL_BASE_PIOB (ATMEL_BASE_PIOA + 0x40)
> > +#define ATMEL_BASE_PIOC (ATMEL_BASE_PIOB + 0x40)
> > +#define ATMEL_BASE_PIOD (ATMEL_BASE_PIOC + 0x40)
> > +
> > +/* SYSC spawns */
> > +#define ATMEL_BASE_RSTC ATMEL_BASE_SYSC
> > +#define ATMEL_BASE_SHDWC (ATMEL_BASE_SYSC + 0x10)
> > +#define ATMEL_BASE_PIT (ATMEL_BASE_SYSC + 0x30)
> > +#define ATMEL_BASE_WDT (ATMEL_BASE_SYSC + 0x40)
> > +#define ATMEL_BASE_SCKC (ATMEL_BASE_SYSC + 0x50)
> > +#define ATMEL_BASE_RTC (ATMEL_BASE_SYSC + 0xb0)
> > +
> > +/*
> > + * Other misc defines
>
> Ditto
>
> You have two section of "Other misc defines", would it be OK to put them together?
Put them together.
>
> > + */
> > +#define ATMEL_PIO_PORTS 4
> > +#define CPU_HAS_PCR
> > +#define CPU_HAS_H32MXDIV
> > +
> > +/* SAMA5D2 series chip id definitions */
> > +#define ARCH_ID_SAMA5D2 0x8a5c08c0
> > +#define ARCH_EXID_SAMA5D21CU 0x0000005a
> > +#define ARCH_EXID_SAMA5D22CU 0x00000059
> > +#define ARCH_EXID_SAMA5D22CN 0x00000069
> > +#define ARCH_EXID_SAMA5D23CU 0x00000058
> > +#define ARCH_EXID_SAMA5D24CX 0x00000004
> > +#define ARCH_EXID_SAMA5D24CU 0x00000014
> > +#define ARCH_EXID_SAMA5D26CU 0x00000012
> > +#define ARCH_EXID_SAMA5D27CU 0x00000011
> > +#define ARCH_EXID_SAMA5D27CN 0x00000021
> > +#define ARCH_EXID_SAMA5D28CU 0x00000010
> > +#define ARCH_EXID_SAMA5D28CN 0x00000020
> > +
> > +#define cpu_is_sama5d2() (get_chip_id() == ARCH_ID_SAMA5D2)
> > +#define cpu_is_sama5d21cu() (cpu_is_sama5d2() && \
> > + (get_extension_chip_id() == ARCH_EXID_SAMA5D21CU))
> > +#define cpu_is_sama5d22cu() (cpu_is_sama5d2() && \
> > + (get_extension_chip_id() == ARCH_EXID_SAMA5D22CU))
> > +#define cpu_is_sama5d22cn() (cpu_is_sama5d2() && \
> > + (get_extension_chip_id() == ARCH_EXID_SAMA5D22CN))
> > +#define cpu_is_sama5d23cu() (cpu_is_sama5d2() && \
> > + (get_extension_chip_id() == ARCH_EXID_SAMA5D23CU))
> > +#define cpu_is_sama5d24cx() (cpu_is_sama5d2() && \
> > + (get_extension_chip_id() == ARCH_EXID_SAMA5D24CX))
> > +#define cpu_is_sama5d24cu() (cpu_is_sama5d2() && \
> > + (get_extension_chip_id() == ARCH_EXID_SAMA5D24CU))
> > +#define cpu_is_sama5d26cu() (cpu_is_sama5d2() && \
> > + (get_extension_chip_id() == ARCH_EXID_SAMA5D26CU))
> > +#define cpu_is_sama5d27cu() (cpu_is_sama5d2() && \
> > + (get_extension_chip_id() == ARCH_EXID_SAMA5D27CU))
> > +#define cpu_is_sama5d27cn() (cpu_is_sama5d2() && \
> > + (get_extension_chip_id() == ARCH_EXID_SAMA5D27CN))
> > +#define cpu_is_sama5d28cu() (cpu_is_sama5d2() && \
> > + (get_extension_chip_id() == ARCH_EXID_SAMA5D28CU))
> > +#define cpu_is_sama5d28cn() (cpu_is_sama5d2() && \
> > + (get_extension_chip_id() == ARCH_EXID_SAMA5D28CN))
>
> I don't see where use this part of code? Add I think it is the same as
> get_cpu_name() function.
Remove cpu_is_sama5d2x() macros, which are unused for now.
Thanks.
>
> > +/* PIT Timer(PIT_PIIR) */
> > +#define CONFIG_SYS_TIMER_COUNTER 0xf804803c
> > +
> > +/* No PMECC Galois table in ROM */
> > +#define NO_GALOIS_TABLE_IN_ROM
> > +
> > +#ifndef __ASSEMBLY__
> > +unsigned int get_chip_id(void);
> > +unsigned int get_extension_chip_id(void); unsigned int
> > +has_lcdc(void); char *get_cpu_name(void); #endif
> > +
> > +#endif
> > diff --git a/board/atmel/sama5d2_xplained/Kconfig
> > b/board/atmel/sama5d2_xplained/Kconfig
> > new file mode 100644
> > index 0000000..55712e9
> > --- /dev/null
> > +++ b/board/atmel/sama5d2_xplained/Kconfig
> > @@ -0,0 +1,15 @@
> > +if TARGET_SAMA5D2_XPLAINED
> > +
> > +config SYS_BOARD
> > + default "sama5d2_xplained"
> > +
> > +config SYS_VENDOR
> > + default "atmel"
> > +
> > +config SYS_SOC
> > + default "at91"
> > +
> > +config SYS_CONFIG_NAME
> > + default "sama5d2_xplained"
> > +
> > +endif
> > diff --git a/board/atmel/sama5d2_xplained/MAINTAINERS
> > b/board/atmel/sama5d2_xplained/MAINTAINERS
> > new file mode 100644
> > index 0000000..ff9c86f
> > --- /dev/null
> > +++ b/board/atmel/sama5d2_xplained/MAINTAINERS
> > @@ -0,0 +1,7 @@
> > +SAMA5D2 XPLAINED BOARD
> > +M: Wenyou Yang <wenyou.yang at atmel.com>
> > +S: Maintained
> > +F: board/atmel/sama5d2_xplained/
> > +F: include/configs/sama5d2_xplained.h
> > +F: configs/sama5d2_xplained_mmc_defconfig
> > +F: configs/sama5d2_xplained_spiflash_defconfig
> > diff --git a/board/atmel/sama5d2_xplained/Makefile
> > b/board/atmel/sama5d2_xplained/Makefile
> > new file mode 100644
> > index 0000000..420870b
> > --- /dev/null
> > +++ b/board/atmel/sama5d2_xplained/Makefile
> > @@ -0,0 +1,8 @@
> > +#
> > +# Copyright (C) 2015 Atmel Corporation
> > +# Wenyou Yang <wenyou.yang at atmel.com>
> > +#
> > +# SPDX-License-Identifier: GPL-2.0+
> > +#
> > +
> > +obj-y += sama5d2_xplained.o
> > diff --git a/board/atmel/sama5d2_xplained/sama5d2_xplained.c
> > b/board/atmel/sama5d2_xplained/sama5d2_xplained.c
> > new file mode 100644
> > index 0000000..adac13a
> > --- /dev/null
> > +++ b/board/atmel/sama5d2_xplained/sama5d2_xplained.c
> > @@ -0,0 +1,282 @@
> > +/*
> > + * Copyright (C) 2015 Atmel Corporation
> > + * Wenyou.Yang <wenyou.yang at atmel.com>
> > + *
> > + * SPDX-License-Identifier: GPL-2.0+
> > + */
> > +
> > +#include <common.h>
> > +#include <atmel_hlcdc.h>
> > +#include <lcd.h>
> > +#include <mmc.h>
> > +#include <net.h>
> > +#include <netdev.h>
> > +#include <spi.h>
> > +#include <version.h>
> > +#include <asm/io.h>
> > +#include <asm/arch/at91_common.h>
> > +#include <asm/arch/at91_pmc.h>
> > +#include <asm/arch/atmel_pio4.h>
> > +#include <asm/arch/atmel_usba_udc.h>
> > +#include <asm/arch/atmel_sdhci.h>
> > +#include <asm/arch/clk.h>
> > +#include <asm/arch/gpio.h>
> > +#include <asm/arch/sama5d2.h>
> > +
> > +DECLARE_GLOBAL_DATA_PTR;
> > +
> > +int spi_cs_is_valid(unsigned int bus, unsigned int cs) {
> > + return bus == 0 && cs == 0;
> > +}
> > +
> > +void spi_cs_activate(struct spi_slave *slave) {
> > + atmel_pio4_set_pio_output(AT91_PIO_PORTA, 17, 0); }
> > +
> > +void spi_cs_deactivate(struct spi_slave *slave) {
> > + atmel_pio4_set_pio_output(AT91_PIO_PORTA, 17, 1); }
> > +
> > +static void board_spi0_hw_init(void)
> > +{
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTA, 14, 0);
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTA, 15, 0);
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTA, 16, 0);
> > +
> > + atmel_pio4_set_pio_output(AT91_PIO_PORTA, 17, 1);
> > +
> > + at91_periph_clk_enable(ATMEL_ID_SPI0);
> > +}
> > +
> > +static void board_usb_hw_init(void)
> > +{
> > + atmel_pio4_set_pio_output(AT91_PIO_PORTB, 9, 1);
> > + atmel_pio4_set_pio_output(AT91_PIO_PORTB, 10, 1); }
> > +
> > +#ifdef CONFIG_LCD
> > +vidinfo_t panel_info = {
> > + .vl_col = 480,
> > + .vl_row = 272,
> > + .vl_clk = 9000000,
> > + .vl_bpix = LCD_BPP,
> > + .vl_tft = 1,
> > + .vl_hsync_len = 41,
> > + .vl_left_margin = 2,
> > + .vl_right_margin = 2,
> > + .vl_vsync_len = 11,
> > + .vl_upper_margin = 2,
> > + .vl_lower_margin = 2,
> > + .mmio = ATMEL_BASE_LCDC,
> > +};
> > +
> > +/* No power up/down pin for the LCD pannel */
> > +void lcd_enable(void) { /* Empty! */ }
> > +void lcd_disable(void) { /* Empty! */ }
> > +
> > +unsigned int has_lcdc(void)
> > +{
> > + return 1;
> > +}
>
> For this, I think you can add a following patch to define it as a weak function, then
> it don't need to repeat it.
Add __weak attribute.
>
> > +
> > +static void board_lcd_hw_init(void)
> > +{
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTC, 28, 0); /* LCDPWM */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTC, 29, 0); /* LCDDISP */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTC, 30, 0); /* LCDVSYNC */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTC, 31, 0); /* LCDHSYNC */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTD, 0, 0); /* LCDPCK */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTD, 1, 0); /* LCDDEN */
> > +
> > + /* LCDDAT0 */
> > + /* LCDDAT1 */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTC, 10, 0); /* LCDDAT2 */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTC, 11, 0); /* LCDDAT3 */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTC, 12, 0); /* LCDDAT4 */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTC, 13, 0); /* LCDDAT5 */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTC, 14, 0); /* LCDDAT6 */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTC, 15, 0); /* LCDDAT7 */
> > +
> > + /* LCDDAT8 */
> > + /* LCDDAT9 */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTC, 16, 0); /* LCDDAT10 */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTC, 17, 0); /* LCDDAT11 */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTC, 18, 0); /* LCDDAT12 */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTC, 19, 0); /* LCDDAT13 */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTC, 20, 0); /* LCDDAT14 */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTC, 21, 0); /* LCDDAT15 */
> > +
> > + /* LCDD16 */
> > + /* LCDD17 */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTC, 22, 0); /* LCDDAT18 */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTC, 23, 0); /* LCDDAT19 */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTC, 24, 0); /* LCDDAT20 */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTC, 25, 0); /* LCDDAT21 */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTC, 26, 0); /* LCDDAT22 */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTC, 27, 0); /* LCDDAT23 */
> > +
> > + at91_periph_clk_enable(ATMEL_ID_LCDC);
> > +}
> > +
> > +#ifdef CONFIG_LCD_INFO
> > +void lcd_show_board_info(void)
> > +{
> > + ulong dram_size;
> > + int i;
> > + char temp[32];
> > +
> > + lcd_printf("%s\n", U_BOOT_VERSION);
> > + lcd_printf("2015 ATMEL Corp\n");
> > + lcd_printf("%s CPU at %s MHz\n", get_cpu_name(),
> > + strmhz(temp, get_cpu_clk_rate()));
> > +
> > + dram_size = 0;
> > + for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
> > + dram_size += gd->bd->bi_dram[i].size;
> > +
> > + lcd_printf("%ld MB SDRAM\n", dram_size >> 20); } #endif /*
> > +CONFIG_LCD_INFO */ #endif /* CONFIG_LCD_INFO */
>
> s/CONFIG_LCD_INFO/CONFIG_LCD
Done
>
> > +
> > +static void board_gmac_hw_init(void)
> > +{
> > + atmel_pio4_set_f_periph(AT91_PIO_PORTB, 14, 0); /* GTXCK */
> > + atmel_pio4_set_f_periph(AT91_PIO_PORTB, 15, 0); /* GTXEN */
> > + atmel_pio4_set_f_periph(AT91_PIO_PORTB, 16, 0); /* GRXDV */
> > + atmel_pio4_set_f_periph(AT91_PIO_PORTB, 17, 0); /* GRXER */
> > + atmel_pio4_set_f_periph(AT91_PIO_PORTB, 18, 0); /* GRX0 */
> > + atmel_pio4_set_f_periph(AT91_PIO_PORTB, 19, 0); /* GRX1 */
> > + atmel_pio4_set_f_periph(AT91_PIO_PORTB, 20, 0); /* GTX0 */
> > + atmel_pio4_set_f_periph(AT91_PIO_PORTB, 21, 0); /* GTX1 */
> > + atmel_pio4_set_f_periph(AT91_PIO_PORTB, 22, 0); /* GMDC */
> > + atmel_pio4_set_f_periph(AT91_PIO_PORTB, 23, 0); /* GMDIO */
> > +
> > + at91_periph_clk_enable(ATMEL_ID_GMAC);
> > +}
> > +
> > +static void board_sdhci0_hw_init(void) {
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTA, 0, 0); /* SDMMC0_CK
> */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTA, 1, 0); /* SDMMC0_CMD
> */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTA, 2, 0); /*
> SDMMC0_DAT0 */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTA, 3, 0); /*
> SDMMC0_DAT1 */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTA, 4, 0); /*
> SDMMC0_DAT2 */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTA, 5, 0); /*
> SDMMC0_DAT3 */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTA, 6, 0); /*
> SDMMC0_DAT4 */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTA, 7, 0); /*
> SDMMC0_DAT5 */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTA, 8, 0); /*
> SDMMC0_DAT6 */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTA, 9, 0); /*
> SDMMC0_DAT7 */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTA, 10, 0); /*
> SDMMC0_RSTN */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTA, 11, 0); /*
> SDMMC0_VDDSEL */
> > +
> > + at91_periph_clk_enable(ATMEL_ID_SDMMC0);
> > + at91_enable_periph_generated_clk(ATMEL_ID_SDMMC0);
> > +}
> > +
> > +static void board_sdhci1_hw_init(void) {
> > + atmel_pio4_set_e_periph(AT91_PIO_PORTA, 18, 0); /*
> SDMMC1_DAT0 */
> > + atmel_pio4_set_e_periph(AT91_PIO_PORTA, 19, 0); /*
> SDMMC1_DAT1 */
> > + atmel_pio4_set_e_periph(AT91_PIO_PORTA, 20, 0); /*
> SDMMC1_DAT2 */
> > + atmel_pio4_set_e_periph(AT91_PIO_PORTA, 21, 0); /*
> SDMMC1_DAT3 */
> > + atmel_pio4_set_e_periph(AT91_PIO_PORTA, 22, 0); /* SDMMC1_CK
> */
> > + atmel_pio4_set_e_periph(AT91_PIO_PORTA, 27, 0); /*
> SDMMC1_RSTN */
> > + atmel_pio4_set_e_periph(AT91_PIO_PORTA, 28, 0); /* SDMMC1_CMD
> */
> > + atmel_pio4_set_e_periph(AT91_PIO_PORTA, 30, 0); /* SDMMC1_CD
> */
> > +
> > + at91_periph_clk_enable(ATMEL_ID_SDMMC1);
> > + at91_enable_periph_generated_clk(ATMEL_ID_SDMMC1);
> > +}
> > +
> > +int board_mmc_init(bd_t *bis)
> > +{
> > +#ifdef CONFIG_ATMEL_SDHCI0
> > + atmel_sdhci_init((void *)ATMEL_BASE_SDMMC0, ATMEL_ID_SDMMC0);
> #endif
> > +#ifdef CONFIG_ATMEL_SDHCI1
> > + atmel_sdhci_init((void *)ATMEL_BASE_SDMMC1, ATMEL_ID_SDMMC1);
> #endif
> > +
> > + return 0;
> > +}
> > +
> > +static void board_uart1_hw_init(void) {
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTD, 2, 1); /* URXD1 */
> > + atmel_pio4_set_a_periph(AT91_PIO_PORTD, 3, 0); /* UTXD1 */
> > +
> > + at91_periph_clk_enable(ATMEL_ID_UART1);
> > +}
> > +
> > +int board_early_init_f(void)
> > +{
> > + at91_periph_clk_enable(ATMEL_ID_PIOA);
> > + at91_periph_clk_enable(ATMEL_ID_PIOB);
> > + at91_periph_clk_enable(ATMEL_ID_PIOC);
> > + at91_periph_clk_enable(ATMEL_ID_PIOD);
> > +
> > + board_uart1_hw_init();
> > +
> > + return 0;
> > +}
> > +
> > +int board_init(void)
> > +{
> > + /* adress of boot parameters */
>
> s/adress/address
Thank you for your finding.
>
> > + gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
> > +
> > +#ifdef CONFIG_ATMEL_SPI
> > + board_spi0_hw_init();
> > +#endif
> > +#ifdef CONFIG_ATMEL_SDHCI
> > +#ifdef CONFIG_ATMEL_SDHCI0
> > + board_sdhci0_hw_init();
> > +#endif
> > +#ifdef CONFIG_ATMEL_SDHCI1
> > + board_sdhci1_hw_init();
> > +#endif
> > +#endif
> > +#ifdef CONFIG_MACB
> > + board_gmac_hw_init();
> > +#endif
> > +#ifdef CONFIG_LCD
> > + board_lcd_hw_init();
> > +#endif
> > +#ifdef CONFIG_CMD_USB
> > + board_usb_hw_init();
> > +#endif
> > +#ifdef CONFIG_USB_GADGET_ATMEL_USBA
> > + at91_udp_hw_init();
> > +#endif
> > +
> > + return 0;
> > +}
> > +
> > +int dram_init(void)
> > +{
> > + gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
> > + CONFIG_SYS_SDRAM_SIZE);
> > + return 0;
> > +}
> > +
> > +int board_eth_init(bd_t *bis)
> > +{
> > + int rc = 0;
> > +
> > +#ifdef CONFIG_MACB
> > + rc = macb_eth_initialize(0, (void *)ATMEL_BASE_GMAC, 0x00); #endif
> > +
> > +#ifdef CONFIG_USB_GADGET_ATMEL_USBA
> > + usba_udc_probe(&pdata);
> > +#ifdef CONFIG_USB_ETH_RNDIS
> > + usb_eth_initialize(bis);
> > +#endif
> > +#endif
>
> Here, I think you'd better address the comments from Andreas.
>
> > +
> > + return rc;
> > +}
> > diff --git a/configs/sama5d2_xplained_mmc_defconfig
> > b/configs/sama5d2_xplained_mmc_defconfig
> > new file mode 100644
> > index 0000000..c1dcbef
> > --- /dev/null
> > +++ b/configs/sama5d2_xplained_mmc_defconfig
> > @@ -0,0 +1,11 @@
> > +CONFIG_ARM=y
> > +CONFIG_ARCH_AT91=y
> > +CONFIG_TARGET_SAMA5D2_XPLAINED=y
> > +CONFIG_SYS_EXTRA_OPTIONS="SAMA5D2,SYS_USE_MMC"
> > +# CONFIG_CMD_IMI is not set
> > +# CONFIG_CMD_IMLS is not set
> > +# CONFIG_CMD_LOADS is not set
> > +# CONFIG_CMD_FLASH is not set
> > +CONFIG_CMD_SF=y
> > +# CONFIG_CMD_FPGA is not set
> > +CONFIG_SPI_FLASH=y
> > diff --git a/configs/sama5d2_xplained_spiflash_defconfig
> > b/configs/sama5d2_xplained_spiflash_defconfig
> > new file mode 100644
> > index 0000000..0271e8e
> > --- /dev/null
> > +++ b/configs/sama5d2_xplained_spiflash_defconfig
> > @@ -0,0 +1,11 @@
> > +CONFIG_ARM=y
> > +CONFIG_ARCH_AT91=y
> > +CONFIG_TARGET_SAMA5D2_XPLAINED=y
> > +CONFIG_SYS_EXTRA_OPTIONS="SAMA5D2,SYS_USE_SERIALFLASH"
> > +# CONFIG_CMD_IMI is not set
> > +# CONFIG_CMD_IMLS is not set
> > +# CONFIG_CMD_LOADS is not set
> > +# CONFIG_CMD_FLASH is not set
> > +CONFIG_CMD_SF=y
> > +# CONFIG_CMD_FPGA is not set
> > +CONFIG_SPI_FLASH=y
> > diff --git a/include/configs/sama5d2_xplained.h
> > b/include/configs/sama5d2_xplained.h
> > new file mode 100644
> > index 0000000..ff9e79c
> > --- /dev/null
> > +++ b/include/configs/sama5d2_xplained.h
> > @@ -0,0 +1,126 @@
> > +/*
> > + * Configuration file for the SAMA5D2 Xplained Board.
> > + *
> > + * Copyright (C) 2015 Atmel Corporation
> > + * Wenyou Yang <wenyou.yang at atmel.com>
> > + *
> > + * SPDX-License-Identifier: GPL-2.0+
> > + */
> > +
> > +#ifndef __CONFIG_H
> > +#define __CONFIG_H
> > +
> > +/* No NOR flash, this definition should put before common header */
> > +#define CONFIG_SYS_NO_FLASH
> > +
> > +#include "at91-sama5_common.h"
> > +
> > +/* serial console */
> > +#define CONFIG_ATMEL_USART
> > +#define CONFIG_USART_BASE ATMEL_BASE_UART1
> > +#define CONFIG_USART_ID ATMEL_ID_UART1
> > +
> > +/* SDRAM */
> > +#define CONFIG_NR_DRAM_BANKS 1
> > +#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_DDRCS
> > +#define CONFIG_SYS_SDRAM_SIZE 0x20000000
> > +
> > +#ifdef CONFIG_SPL_BUILD
>
> As you don't support SPL, can you add this later? (The same time when add spl
> support)
Removed. The SPL support will be added soon.
>
> > +#define CONFIG_SYS_INIT_SP_ADDR 0x210000
> > +#else
> > +#define CONFIG_SYS_INIT_SP_ADDR \
> > + (CONFIG_SYS_SDRAM_BASE + 4 * 1024 -
> GENERATED_GBL_DATA_SIZE) #endif
> > +
> > +#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load
> address */
> > +
> > +#undef CONFIG_AT91_GPIO
> > +#define CONFIG_ATMEL_PIO4
> > +
> > +/* SerialFlash */
> > +#ifdef CONFIG_CMD_SF
> > +#define CONFIG_ATMEL_SPI
> > +#define CONFIG_ATMEL_SPI0
> > +#define CONFIG_SPI_FLASH_ATMEL
> > +#define CONFIG_SF_DEFAULT_BUS 0
> > +#define CONFIG_SF_DEFAULT_CS 0
> > +#define CONFIG_SF_DEFAULT_SPEED 30000000
> > +#endif
> > +
> > +/* NAND flash */
> > +#undef CONFIG_CMD_NAND
> > +
> > +/* MMC */
> > +#define CONFIG_CMD_MMC
> > +
> > +#ifdef CONFIG_CMD_MMC
> > +#define CONFIG_MMC
> > +#define CONFIG_GENERIC_MMC
> > +#define CONFIG_SDHCI
> > +#define CONFIG_ATMEL_SDHCI
> > +#define CONFIG_ATMEL_SDHCI0
> > +#define CONFIG_ATMEL_SDHCI1
> > +#define CONFIG_SUPPORT_EMMC_BOOT
> > +#endif
> > +
> > +/* USB */
> > +#define CONFIG_CMD_USB
> > +
> > +#ifdef CONFIG_CMD_USB
> > +#define CONFIG_USB_EHCI
> > +#define CONFIG_USB_EHCI_ATMEL
> > +#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
> > +#define CONFIG_USB_STORAGE
> > +#endif
> > +
> > +/* USB device */
> > +#define CONFIG_USB_GADGET
> > +#define CONFIG_USB_GADGET_DUALSPEED
> > +#define CONFIG_USB_GADGET_ATMEL_USBA
> > +#define CONFIG_USB_ETHER
> > +#define CONFIG_USB_ETH_RNDIS
> > +#define CONFIG_USBNET_MANUFACTURER "Atmel SAMA5D2 XPlained"
> > +
> > +#if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC) #define
> > +CONFIG_CMD_FAT #define CONFIG_DOS_PARTITION #endif
> > +
> > +/* Ethernet Hardware */
> > +#define CONFIG_MACB
> > +#define CONFIG_RMII
> > +#define CONFIG_NET_RETRY_COUNT 20
> > +#define CONFIG_MACB_SEARCH_PHY
> > +
> > +/* LCD */
> > +/* #define CONFIG_LCD */
> > +
> > +#ifdef CONFIG_LCD
> > +#define LCD_BPP LCD_COLOR16
> > +#define LCD_OUTPUT_BPP 24
> > +#define CONFIG_LCD_LOGO
> > +#define CONFIG_LCD_INFO
> > +#define CONFIG_LCD_INFO_BELOW_LOGO
> > +#define CONFIG_SYS_WHITE_ON_BLACK
> > +#define CONFIG_ATMEL_HLCD
> > +#define CONFIG_ATMEL_LCD_RGB565
> > +#define CONFIG_SYS_CONSOLE_IS_IN_ENV
> > +#endif
> > +
> > +#ifdef CONFIG_SYS_USE_MMC
> > +
> > +/* bootstrap + u-boot + env in sd card */ #undef
> > +FAT_ENV_DEVICE_AND_PART #undef CONFIG_BOOTCOMMAND
> > +
> > +#define FAT_ENV_DEVICE_AND_PART "1"
> > +#define CONFIG_BOOTCOMMAND "fatload mmc 1:1 0x21000000 at91-
> sama5d2_xplained.dtb; " \
> > + "fatload mmc 1:1 0x22000000 zImage; " \
> > + "bootz 0x22000000 - 0x21000000"
> > +#undef CONFIG_BOOTARGS
> > +#define CONFIG_BOOTARGS \
> > + "console=ttyS0,115200 earlyprintk root=/dev/mmcblk1p2 rw rootwait"
> > +
> > +#endif
>
> This part also present in at91-sama5_common.h, can it be used?
They have a little difference, so be overridden.
>
> > +
> > +#endif
> >
>
> Best Regards,
> Bo Shen
Best Regards,
Wenyou Yang
More information about the U-Boot
mailing list