[U-Boot] [PATCH v4 4/6] cgtqmx6eval: Add SPL support
Otavio Salvador
otavio at ossystems.com.br
Thu Oct 29 11:32:53 CET 2015
Congatec has several MX6 boards based on quad, dual, dual-lite and solo.
Add SPL support so that all the variants can be supported.
Signed-off-by: Otavio Salvador <otavio at ossystems.com.br>
---
Changes in v4:
- Rework README (Marek)
- Rework code to compare part-# (Marek)
arch/arm/cpu/armv7/mx6/Kconfig | 3 +
board/congatec/cgtqmx6eval/README | 74 ++-
board/congatec/cgtqmx6eval/cgtqmx6eval.c | 579 +++++++++++++++++----
board/congatec/cgtqmx6eval/imximage.cfg | 143 -----
...gtqmx6qeval_defconfig => cgtqmx6eval_defconfig} | 5 +-
include/configs/cgtqmx6eval.h | 21 +-
6 files changed, 564 insertions(+), 261 deletions(-)
delete mode 100644 board/congatec/cgtqmx6eval/imximage.cfg
rename configs/{cgtqmx6qeval_defconfig => cgtqmx6eval_defconfig} (57%)
diff --git a/arch/arm/cpu/armv7/mx6/Kconfig b/arch/arm/cpu/armv7/mx6/Kconfig
index 0b02e9e..9ee509e 100644
--- a/arch/arm/cpu/armv7/mx6/Kconfig
+++ b/arch/arm/cpu/armv7/mx6/Kconfig
@@ -44,6 +44,9 @@ config TARGET_ARISTAINETOS2B
config TARGET_CGTQMX6EVAL
bool "cgtqmx6eval"
+ select SUPPORT_SPL
+ select DM
+ select DM_THERMAL
config TARGET_CM_FX6
bool "CM-FX6"
diff --git a/board/congatec/cgtqmx6eval/README b/board/congatec/cgtqmx6eval/README
index 5e76d2a..2361b9a 100644
--- a/board/congatec/cgtqmx6eval/README
+++ b/board/congatec/cgtqmx6eval/README
@@ -1,28 +1,66 @@
-U-Boot for the Congatec Conga-QEVAl Evaluation Carrier board with
-qmx6 quad module.
+U-Boot for the Congatec QMX6 boards
This file contains information for the port of U-Boot to the Congatec
-Conga-QEVAl Evaluation Carrier board with qmx6 quad module.
+QMX6 boards.
-1. Boot source, boot from SD card
+1. Building U-boot
+------------------
+
+- Build U-boot for Congatec QMX6 boards:
+
+$ make mrproper
+$ make cgtqmx6eval_defconfig
+$ make
+
+This will generate the following binaries:
+
+- SPL
+- u-boot.img
+
+2. Flashing U-boot in the SPI NOR
---------------------------------
-By default, the Congatec board can boot only from the SPI-NOR.
-But, with the u-boot version provided with the board you can write boot
-registers to force the board to reboot and boot from the SD slot. If
-"bmode" command is not available from your pre-installed u-boot, these
-instruction will produce the same effect:
+Copy SPL and u-boot.img to the exported TFTP directory of the
+host PC (/tftpboot , for example).
+
+=> sf probe
+
+=> tftp SPL
+
+=> sf update 0x12000000 0x400 0x10000
+
+=> tftp u-boot.img
+
+=> sf update 0x12000000 0x10000 0x70000
+
+Reboot the board and the new U-boot should come up.
+
+3. Booting from the SD card
+---------------------------
+
+- Flash the SPL image into the SD card:
+
+sudo dd if=SPL of=/dev/mmcblk0 bs=1k seek=1; sync
+
+- Flash the u-boot.img image into the SD card:
+
+sudo dd if=u-boot.img of=/dev/mmcblk0 bs=1k seek=69; sync
+
+- Insert the SD card into the big slot.
+
+The boot medium of Congatec QMX6 boards is the SPI NOR flash, so boot
+the board from SPI first.
-conga-QMX6 U-Boot > mw.l 0x20d8040 0x3850
-conga-QMX6 U-Boot > mw.l 0x020d8044 0x10000000
-conga-QMX6 U-Boot > reset
-resetting ...
+It is also possible to boot from the SD card slot by using the 'bmode'
+command:
-The the board will reboot and, if you have written your SD correctly
-the board will use u-boot that live into the SD
+=> bmode esdhc4
-To copy the resulting u-boot.imx to the SD card:
+And then the U-boot from the big slot will boot.
- dd if=u-boot.imx of=/dev/xxx bs=512 seek=2
+Note: If the "bmode" command is not available from your pre-installed U-boot,
+these instruction will produce the same effect:
-Note: Replace xxx with the device representing the SD card in your system.
+=> mw.l 0x20d8040 0x3850
+=> mw.l 0x020d8044 0x10000000
+=> reset
diff --git a/board/congatec/cgtqmx6eval/cgtqmx6eval.c b/board/congatec/cgtqmx6eval/cgtqmx6eval.c
index 18e408b..6a99aad 100644
--- a/board/congatec/cgtqmx6eval/cgtqmx6eval.c
+++ b/board/congatec/cgtqmx6eval/cgtqmx6eval.c
@@ -18,6 +18,7 @@
#include <asm/imx-common/sata.h>
#include <asm/imx-common/boot_mode.h>
#include <asm/imx-common/mxc_i2c.h>
+#include <asm/arch/sys_proto.h>
#include <asm/arch/mxc_hdmi.h>
#include <asm/arch/crm_regs.h>
#include <mmc.h>
@@ -31,6 +32,8 @@
#include <miiphy.h>
#include <netdev.h>
#include <micrel.h>
+#include <spi_flash.h>
+#include <spi.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -58,121 +61,134 @@ DECLARE_GLOBAL_DATA_PTR;
int dram_init(void)
{
- gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
+ gd->ram_size = imx_ddr_size();
return 0;
}
static iomux_v3_cfg_t const uart2_pads[] = {
- MX6_PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ IOMUX_PADS(PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
};
static iomux_v3_cfg_t const usdhc2_pads[] = {
- MX6_PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_GPIO_4__GPIO1_IO04 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ IOMUX_PADS(PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_GPIO_4__GPIO1_IO04 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
};
static iomux_v3_cfg_t const usdhc3_pads[] = {
- MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_RST__SD3_RESET | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ IOMUX_PADS(PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_RST__SD3_RESET | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
};
static iomux_v3_cfg_t const usdhc4_pads[] = {
- MX6_PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NANDF_D6__GPIO2_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
+ IOMUX_PADS(PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_D6__GPIO2_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL)),
};
static iomux_v3_cfg_t const usb_otg_pads[] = {
- MX6_PAD_EIM_D22__USB_OTG_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_GPIO_1__USB_OTG_ID | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_EIM_D22__USB_OTG_PWR | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_GPIO_1__USB_OTG_ID | MUX_PAD_CTRL(NO_PAD_CTRL)),
};
static iomux_v3_cfg_t enet_pads_ksz9031[] = {
- MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RXC__GPIO6_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_RGMII_RD0__GPIO6_IO25 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_RGMII_RD1__GPIO6_IO27 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_RGMII_RD2__GPIO6_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_RGMII_RD3__GPIO6_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),
- MX6_PAD_RGMII_RX_CTL__GPIO6_IO24 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_RXC__GPIO6_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_RD0__GPIO6_IO25 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_RD1__GPIO6_IO27 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_RD2__GPIO6_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_RD3__GPIO6_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_RX_CTL__GPIO6_IO24 | MUX_PAD_CTRL(NO_PAD_CTRL)),
};
static iomux_v3_cfg_t enet_pads_final_ksz9031[] = {
- MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ IOMUX_PADS(PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL)),
};
static iomux_v3_cfg_t enet_pads_ar8035[] = {
- MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+ IOMUX_PADS(PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL)),
};
static iomux_v3_cfg_t const ecspi1_pads[] = {
- MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6_PAD_EIM_D19__GPIO3_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IOMUX_PADS(PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_D19__GPIO3_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL)),
};
#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
-struct i2c_pads_info i2c_pad_info1 = {
+struct i2c_pads_info mx6q_i2c_pad_info1 = {
.scl = {
- .i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | PC,
- .gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12 | PC,
+ .i2c_mode = MX6Q_PAD_KEY_COL3__I2C2_SCL | PC,
+ .gpio_mode = MX6Q_PAD_KEY_COL3__GPIO4_IO12 | PC,
.gp = IMX_GPIO_NR(4, 12)
},
.sda = {
- .i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | PC,
- .gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | PC,
+ .i2c_mode = MX6Q_PAD_KEY_ROW3__I2C2_SDA | PC,
+ .gpio_mode = MX6Q_PAD_KEY_ROW3__GPIO4_IO13 | PC,
+ .gp = IMX_GPIO_NR(4, 13)
+ }
+};
+
+struct i2c_pads_info mx6dl_i2c_pad_info1 = {
+ .scl = {
+ .i2c_mode = MX6DL_PAD_KEY_COL3__I2C2_SCL | PC,
+ .gpio_mode = MX6DL_PAD_KEY_COL3__GPIO4_IO12 | PC,
+ .gp = IMX_GPIO_NR(4, 12)
+ },
+ .sda = {
+ .i2c_mode = MX6DL_PAD_KEY_ROW3__I2C2_SDA | PC,
+ .gpio_mode = MX6DL_PAD_KEY_ROW3__GPIO4_IO13 | PC,
.gp = IMX_GPIO_NR(4, 13)
}
};
@@ -241,13 +257,8 @@ int board_eth_init(bd_t *bis)
unsigned short id1, id2;
int ret;
- iomux_v3_cfg_t enet_reset = MX6_PAD_EIM_D23__GPIO3_IO23 |
- MUX_PAD_CTRL(NO_PAD_CTRL);
-
/* check whether KSZ9031 or AR8035 has to be configured */
- imx_iomux_v3_setup_multiple_pads(enet_pads_ar8035,
- ARRAY_SIZE(enet_pads_ar8035));
- imx_iomux_v3_setup_pad(enet_reset);
+ SETUP_IOMUX_PADS(enet_pads_ar8035);
/* phy reset */
gpio_direction_output(IMX_GPIO_NR(3, 23), 0);
@@ -281,13 +292,11 @@ int board_eth_init(bd_t *bis)
gpio_set_value(IMX_GPIO_NR(6, 27), 1);
gpio_set_value(IMX_GPIO_NR(6, 28), 1);
gpio_set_value(IMX_GPIO_NR(6, 29), 1);
- imx_iomux_v3_setup_multiple_pads(enet_pads_ksz9031,
- ARRAY_SIZE(enet_pads_ksz9031));
+ SETUP_IOMUX_PADS(enet_pads_ksz9031);
gpio_set_value(IMX_GPIO_NR(6, 24), 1);
udelay(500);
gpio_set_value(IMX_GPIO_NR(3, 23), 1);
- imx_iomux_v3_setup_multiple_pads(enet_pads_final_ksz9031,
- ARRAY_SIZE(enet_pads_final_ksz9031));
+ SETUP_IOMUX_PADS(enet_pads_final_ksz9031);
} else if ((id1 == 0x004d) && (id2 == 0xd072)) {
/* configure Atheros AR8035 - actually nothing to do */
printf("configure Atheros AR8035 Ethernet Phy at address %d\n",
@@ -389,7 +398,7 @@ int board_phy_config(struct phy_device *phydev)
static void setup_iomux_uart(void)
{
- imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
+ SETUP_IOMUX_PADS(uart2_pads);
}
void setup_spinor(void)
@@ -431,6 +440,7 @@ int board_mmc_getcd(struct mmc *mmc)
int board_mmc_init(bd_t *bis)
{
+#ifndef CONFIG_SPL_BUILD
s32 status = 0;
int i;
@@ -438,9 +448,9 @@ int board_mmc_init(bd_t *bis)
usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
- imx_iomux_v3_setup_multiple_pads(usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
- imx_iomux_v3_setup_multiple_pads(usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
- imx_iomux_v3_setup_multiple_pads(usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
+ SETUP_IOMUX_PADS(usdhc2_pads);
+ SETUP_IOMUX_PADS(usdhc3_pads);
+ SETUP_IOMUX_PADS(usdhc4_pads);
for (i = 0; i < ARRAY_SIZE(usdhc_cfg); i++) {
status = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
@@ -449,6 +459,14 @@ int board_mmc_init(bd_t *bis)
}
return 0;
+#else
+ SETUP_IOMUX_PADS(usdhc4_pads);
+ usdhc_cfg[0].esdhc_base = USDHC4_BASE_ADDR;
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
+ gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
+
+ return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+#endif
}
#endif
@@ -456,8 +474,7 @@ int board_ehci_hcd_init(int port)
{
switch (port) {
case 0:
- imx_iomux_v3_setup_multiple_pads(usb_otg_pads,
- ARRAY_SIZE(usb_otg_pads));
+ SETUP_IOMUX_PADS(usb_otg_pads);
/*
* set daisy chain for otg_pin_id on 6q.
* for 6dl, this bit is reserved
@@ -659,6 +676,14 @@ int overwrite_console(void)
return 1;
}
+static bool is_mx6q(void)
+{
+ if (is_cpu_type(MXC_CPU_MX6Q) || is_cpu_type(MXC_CPU_MX6D))
+ return true;
+ else
+ return false;
+}
+
int board_early_init_f(void)
{
setup_iomux_uart();
@@ -673,7 +698,11 @@ int board_init(void)
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
- setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
+
+ if (is_mx6q())
+ setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6q_i2c_pad_info1);
+ else
+ setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c_pad_info1);
#ifdef CONFIG_CMD_SATA
setup_sata();
@@ -684,7 +713,18 @@ int board_init(void)
int checkboard(void)
{
- puts("Board: Conga-QEVAL QMX6 Quad\n");
+ char *type = "unknown";
+
+ if (is_cpu_type(MXC_CPU_MX6Q))
+ type = "Quad";
+ else if (is_cpu_type(MXC_CPU_MX6D))
+ type = "Dual";
+ else if (is_cpu_type(MXC_CPU_MX6DL))
+ type = "Dual-Lite";
+ else if (is_cpu_type(MXC_CPU_MX6SOLO))
+ type = "Solo";
+
+ printf("Board: conga-QMX6 %s\n", type);
return 0;
}
@@ -710,3 +750,348 @@ int misc_init_r(void)
#endif
return 0;
}
+
+int board_late_init(void)
+{
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+ if (is_mx6q())
+ setenv("board_rev", "MX6Q");
+ else
+ setenv("board_rev", "MX6DL");
+#endif
+
+ return 0;
+}
+
+#ifdef CONFIG_SPL_BUILD
+#include <asm/arch/mx6-ddr.h>
+#include <spl.h>
+#include <libfdt.h>
+#include <spi_flash.h>
+#include <spi.h>
+
+const struct mx6dq_iomux_ddr_regs mx6q_ddr_ioregs = {
+ .dram_sdclk_0 = 0x00000030,
+ .dram_sdclk_1 = 0x00000030,
+ .dram_cas = 0x00000030,
+ .dram_ras = 0x00000030,
+ .dram_reset = 0x00000030,
+ .dram_sdcke0 = 0x00003000,
+ .dram_sdcke1 = 0x00003000,
+ .dram_sdba2 = 0x00000000,
+ .dram_sdodt0 = 0x00000030,
+ .dram_sdodt1 = 0x00000030,
+ .dram_sdqs0 = 0x00000030,
+ .dram_sdqs1 = 0x00000030,
+ .dram_sdqs2 = 0x00000030,
+ .dram_sdqs3 = 0x00000030,
+ .dram_sdqs4 = 0x00000030,
+ .dram_sdqs5 = 0x00000030,
+ .dram_sdqs6 = 0x00000030,
+ .dram_sdqs7 = 0x00000030,
+ .dram_dqm0 = 0x00000030,
+ .dram_dqm1 = 0x00000030,
+ .dram_dqm2 = 0x00000030,
+ .dram_dqm3 = 0x00000030,
+ .dram_dqm4 = 0x00000030,
+ .dram_dqm5 = 0x00000030,
+ .dram_dqm6 = 0x00000030,
+ .dram_dqm7 = 0x00000030,
+};
+
+static const struct mx6sdl_iomux_ddr_regs mx6dl_ddr_ioregs = {
+ .dram_sdclk_0 = 0x00000030,
+ .dram_sdclk_1 = 0x00000030,
+ .dram_cas = 0x00000030,
+ .dram_ras = 0x00000030,
+ .dram_reset = 0x00000030,
+ .dram_sdcke0 = 0x00003000,
+ .dram_sdcke1 = 0x00003000,
+ .dram_sdba2 = 0x00000000,
+ .dram_sdodt0 = 0x00000030,
+ .dram_sdodt1 = 0x00000030,
+ .dram_sdqs0 = 0x00000030,
+ .dram_sdqs1 = 0x00000030,
+ .dram_sdqs2 = 0x00000030,
+ .dram_sdqs3 = 0x00000030,
+ .dram_sdqs4 = 0x00000030,
+ .dram_sdqs5 = 0x00000030,
+ .dram_sdqs6 = 0x00000030,
+ .dram_sdqs7 = 0x00000030,
+ .dram_dqm0 = 0x00000030,
+ .dram_dqm1 = 0x00000030,
+ .dram_dqm2 = 0x00000030,
+ .dram_dqm3 = 0x00000030,
+ .dram_dqm4 = 0x00000030,
+ .dram_dqm5 = 0x00000030,
+ .dram_dqm6 = 0x00000030,
+ .dram_dqm7 = 0x00000030,
+};
+
+const struct mx6dq_iomux_grp_regs mx6q_grp_ioregs = {
+ .grp_ddr_type = 0x000C0000,
+ .grp_ddrmode_ctl = 0x00020000,
+ .grp_ddrpke = 0x00000000,
+ .grp_addds = 0x00000030,
+ .grp_ctlds = 0x00000030,
+ .grp_ddrmode = 0x00020000,
+ .grp_b0ds = 0x00000030,
+ .grp_b1ds = 0x00000030,
+ .grp_b2ds = 0x00000030,
+ .grp_b3ds = 0x00000030,
+ .grp_b4ds = 0x00000030,
+ .grp_b5ds = 0x00000030,
+ .grp_b6ds = 0x00000030,
+ .grp_b7ds = 0x00000030,
+};
+
+static const struct mx6sdl_iomux_grp_regs mx6sdl_grp_ioregs = {
+ .grp_ddr_type = 0x000c0000,
+ .grp_ddrmode_ctl = 0x00020000,
+ .grp_ddrpke = 0x00000000,
+ .grp_addds = 0x00000030,
+ .grp_ctlds = 0x00000030,
+ .grp_ddrmode = 0x00020000,
+ .grp_b0ds = 0x00000030,
+ .grp_b1ds = 0x00000030,
+ .grp_b2ds = 0x00000030,
+ .grp_b3ds = 0x00000030,
+ .grp_b4ds = 0x00000030,
+ .grp_b5ds = 0x00000030,
+ .grp_b6ds = 0x00000030,
+ .grp_b7ds = 0x00000030,
+};
+
+const struct mx6_mmdc_calibration mx6q_mmcd_calib = {
+ .p0_mpwldectrl0 = 0x0016001A,
+ .p0_mpwldectrl1 = 0x0023001C,
+ .p1_mpwldectrl0 = 0x0028003A,
+ .p1_mpwldectrl1 = 0x001F002C,
+ .p0_mpdgctrl0 = 0x43440354,
+ .p0_mpdgctrl1 = 0x033C033C,
+ .p1_mpdgctrl0 = 0x43300368,
+ .p1_mpdgctrl1 = 0x03500330,
+ .p0_mprddlctl = 0x3228242E,
+ .p1_mprddlctl = 0x2C2C2636,
+ .p0_mpwrdlctl = 0x36323A38,
+ .p1_mpwrdlctl = 0x42324440,
+};
+
+const struct mx6_mmdc_calibration mx6q_2g_mmcd_calib = {
+ .p0_mpwldectrl0 = 0x00080016,
+ .p0_mpwldectrl1 = 0x001D0016,
+ .p1_mpwldectrl0 = 0x0018002C,
+ .p1_mpwldectrl1 = 0x000D001D,
+ .p0_mpdgctrl0 = 0x43200334,
+ .p0_mpdgctrl1 = 0x0320031C,
+ .p1_mpdgctrl0 = 0x0344034C,
+ .p1_mpdgctrl1 = 0x03380314,
+ .p0_mprddlctl = 0x3E36383A,
+ .p1_mprddlctl = 0x38363240,
+ .p0_mpwrdlctl = 0x36364238,
+ .p1_mpwrdlctl = 0x4230423E,
+};
+
+static const struct mx6_mmdc_calibration mx6s_mmcd_calib = {
+ .p0_mpwldectrl0 = 0x00480049,
+ .p0_mpwldectrl1 = 0x00410044,
+ .p0_mpdgctrl0 = 0x42480248,
+ .p0_mpdgctrl1 = 0x023C023C,
+ .p0_mprddlctl = 0x40424644,
+ .p0_mpwrdlctl = 0x34323034,
+};
+
+const struct mx6_mmdc_calibration mx6dl_mmcd_calib = {
+ .p0_mpwldectrl0 = 0x0043004B,
+ .p0_mpwldectrl1 = 0x003A003E,
+ .p1_mpwldectrl0 = 0x0047004F,
+ .p1_mpwldectrl1 = 0x004E0061,
+ .p0_mpdgctrl0 = 0x42500250,
+ .p0_mpdgctrl1 = 0x0238023C,
+ .p1_mpdgctrl0 = 0x42640264,
+ .p1_mpdgctrl1 = 0x02500258,
+ .p0_mprddlctl = 0x40424846,
+ .p1_mprddlctl = 0x46484842,
+ .p0_mpwrdlctl = 0x38382C30,
+ .p1_mpwrdlctl = 0x34343430,
+};
+
+static struct mx6_ddr3_cfg mem_ddr_2g = {
+ .mem_speed = 1600,
+ .density = 2,
+ .width = 16,
+ .banks = 8,
+ .rowaddr = 14,
+ .coladdr = 10,
+ .pagesz = 2,
+ .trcd = 1310,
+ .trcmin = 4875,
+ .trasmin = 3500,
+};
+
+static struct mx6_ddr3_cfg mem_ddr_4g = {
+ .mem_speed = 1600,
+ .density = 4,
+ .width = 16,
+ .banks = 8,
+ .rowaddr = 15,
+ .coladdr = 10,
+ .pagesz = 2,
+ .trcd = 1310,
+ .trcmin = 4875,
+ .trasmin = 3500,
+};
+
+static void ccgr_init(void)
+{
+ struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+ writel(0x00C03F3F, &ccm->CCGR0);
+ writel(0x0030FC03, &ccm->CCGR1);
+ writel(0x0FFFC000, &ccm->CCGR2);
+ writel(0x3FF00000, &ccm->CCGR3);
+ writel(0x00FFF300, &ccm->CCGR4);
+ writel(0x0F0000C3, &ccm->CCGR5);
+ writel(0x000003FF, &ccm->CCGR6);
+}
+
+static void gpr_init(void)
+{
+ struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+
+ /* enable AXI cache for VDOA/VPU/IPU */
+ writel(0xF00000CF, &iomux->gpr[4]);
+ /* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
+ writel(0x007F007F, &iomux->gpr[6]);
+ writel(0x007F007F, &iomux->gpr[7]);
+}
+
+/* Define a minimal structure so that the part number can be read via SPL */
+struct mfgdata {
+ unsigned char tsize;
+ /* size of checksummed part in bytes */
+ unsigned char ckcnt;
+ /* checksum corrected byte */
+ unsigned char cksum;
+ /* decimal serial number, packed BCD */
+ unsigned char serial[6];
+ /* part number, right justified, ASCII */
+ unsigned char pn[16];
+};
+
+static void conv_ascii(unsigned char *dst, unsigned char *src, int len)
+{
+ int remain = len;
+ unsigned char *sptr = src;
+ unsigned char *dptr = dst;
+
+ while (remain)
+ {
+ if (*sptr) {
+ *dptr = *sptr;
+ dptr++;
+ }
+ sptr++;
+ remain--;
+ }
+ *dptr = 0x0;
+}
+
+#define CFG_MFG_ADDR_OFFSET (spi->size - SZ_16K)
+static bool is_2gb(void)
+{
+ struct spi_flash *spi;
+ int ret;
+ char buf[sizeof(struct mfgdata)];
+ struct mfgdata *data = (struct mfgdata *)buf;
+ unsigned char outbuf[32];
+
+ spi = spi_flash_probe(CONFIG_ENV_SPI_BUS,
+ CONFIG_ENV_SPI_CS,
+ CONFIG_ENV_SPI_MAX_HZ, CONFIG_ENV_SPI_MODE);
+ ret = spi_flash_read(spi, CFG_MFG_ADDR_OFFSET, sizeof(struct mfgdata),
+ buf);
+ if (ret)
+ return false;
+
+ /* Congatec Part Numbers 104 and 105 have 2GiB of RAM */
+ conv_ascii(outbuf, data->pn, sizeof(data->pn));
+ if (!memcmp(outbuf, "016104", 6) || !memcmp(outbuf, "016105", 6))
+ return true;
+ else
+ return false;
+}
+
+static void spl_dram_init(int width)
+{
+ struct mx6_ddr_sysinfo sysinfo = {
+ /* width of data bus:0=16,1=32,2=64 */
+ .dsize = width / 32,
+ /* config for full 4GB range so that get_mem_size() works */
+ .cs_density = 32, /* 32Gb per CS */
+ /* single chip select */
+ .ncs = 1,
+ .cs1_mirror = 0,
+ .rtt_wr = 2,
+ .rtt_nom = 2,
+ .walat = 0,
+ .ralat = 5,
+ .mif3_mode = 3,
+ .bi_on = 1,
+ .sde_to_rst = 0x0d,
+ .rst_to_cke = 0x20,
+ };
+
+ if (is_cpu_type(MXC_CPU_MX6Q) && is_2gb()) {
+ mx6dq_dram_iocfg(width, &mx6q_ddr_ioregs, &mx6q_grp_ioregs);
+ mx6_dram_cfg(&sysinfo, &mx6q_2g_mmcd_calib, &mem_ddr_4g);
+ return;
+ }
+
+ if (is_mx6q()) {
+ mx6dq_dram_iocfg(width, &mx6q_ddr_ioregs, &mx6q_grp_ioregs);
+ mx6_dram_cfg(&sysinfo, &mx6q_mmcd_calib, &mem_ddr_2g);
+ } else if (is_cpu_type(MXC_CPU_MX6SOLO)) {
+ sysinfo.walat = 1; // add additional write latency for Solo and DualLite
+ mx6sdl_dram_iocfg(width, &mx6dl_ddr_ioregs, &mx6sdl_grp_ioregs);
+ mx6_dram_cfg(&sysinfo, &mx6s_mmcd_calib, &mem_ddr_4g);
+ } else if (is_cpu_type(MXC_CPU_MX6DL)) {
+ sysinfo.walat = 1; // add additional write latency for Solo and DualLite
+ mx6sdl_dram_iocfg(width, &mx6dl_ddr_ioregs, &mx6sdl_grp_ioregs);
+ mx6_dram_cfg(&sysinfo, &mx6dl_mmcd_calib, &mem_ddr_2g);
+ }
+}
+
+void board_init_f(ulong dummy)
+{
+ /* setup AIPS and disable watchdog */
+ arch_cpu_init();
+
+ ccgr_init();
+ gpr_init();
+
+ /* iomux and setup of i2c */
+ board_early_init_f();
+
+ /* setup GP timer */
+ timer_init();
+
+ /* UART clocks enabled and gd valid - init serial console */
+ preloader_console_init();
+
+ /* Needed for malloc() to work in SPL prior to board_init_r() */
+ spl_init();
+
+ /* DDR initialization */
+ if (is_cpu_type(MXC_CPU_MX6SOLO))
+ spl_dram_init(32);
+ else
+ spl_dram_init(64);
+
+ /* Clear the BSS. */
+ memset(__bss_start, 0, __bss_end - __bss_start);
+
+ /* load/boot image from boot device */
+ board_init_r(NULL, 0);
+}
+#endif
diff --git a/board/congatec/cgtqmx6eval/imximage.cfg b/board/congatec/cgtqmx6eval/imximage.cfg
deleted file mode 100644
index 8c03a49..0000000
--- a/board/congatec/cgtqmx6eval/imximage.cfg
+++ /dev/null
@@ -1,143 +0,0 @@
-/*
- * Copyright (C) 2011 Freescale Semiconductor, Inc.
- * Jason Liu <r64343 at freescale.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- *
- * Refer doc/README.imximage for more details about how-to configure
- * and create imximage boot image
- *
- * The syntax is taken as close as possible with the kwbimage
- */
-
-/* image version */
-IMAGE_VERSION 2
-
-/*
- * Boot Device : one of
- * spi, sd (the board has no nand neither onenand)
- */
-BOOT_FROM sd
-
-/*
- * Device Configuration Data (DCD)
- *
- * Each entry must have the format:
- * Addr-type Address Value
- *
- * where:
- * Addr-type register length (1,2 or 4 bytes)
- * Address absolute address of the register
- * value value to be stored in the register
- */
-DATA 4 0x020e0798 0x000C0000
-DATA 4 0x020e0758 0x00000000
-DATA 4 0x020e0588 0x00000030
-DATA 4 0x020e0594 0x00000030
-DATA 4 0x020e056c 0x00000030
-DATA 4 0x020e0578 0x00000030
-DATA 4 0x020e074c 0x00000030
-DATA 4 0x020e057c 0x000c0030
-DATA 4 0x020e058c 0x00000000
-DATA 4 0x020e059c 0x00003030
-DATA 4 0x020e05a0 0x00003030
-DATA 4 0x020e078c 0x00000030
-DATA 4 0x020e0750 0x00020000
-DATA 4 0x020e05a8 0x00000030
-DATA 4 0x020e05b0 0x00000030
-DATA 4 0x020e0524 0x00000030
-DATA 4 0x020e051c 0x00000030
-DATA 4 0x020e0518 0x00000030
-DATA 4 0x020e050c 0x00000030
-DATA 4 0x020e05b8 0x00000030
-DATA 4 0x020e05c0 0x00000030
-DATA 4 0x020e0774 0x00020000
-DATA 4 0x020e0784 0x00000030
-DATA 4 0x020e0788 0x00000030
-DATA 4 0x020e0794 0x00000030
-DATA 4 0x020e079c 0x00000030
-DATA 4 0x020e07a0 0x00000030
-DATA 4 0x020e07a4 0x00000030
-DATA 4 0x020e07a8 0x00000030
-DATA 4 0x020e0748 0x00000030
-DATA 4 0x020e05ac 0x00000030
-DATA 4 0x020e05b4 0x00000030
-DATA 4 0x020e0528 0x00000030
-DATA 4 0x020e0520 0x00000030
-DATA 4 0x020e0514 0x00000030
-DATA 4 0x020e0510 0x00000030
-DATA 4 0x020e05bc 0x00000030
-DATA 4 0x020e05c4 0x00000030
-DATA 4 0x021b0800 0xa1390003
-DATA 4 0x021b4800 0xa1390003
-DATA 4 0x021b080c 0x00110019
-DATA 4 0x021b0810 0x00260019
-DATA 4 0x021b480c 0x001A0031
-DATA 4 0x021b4810 0x001A0021
-DATA 4 0x021b083c 0x43100316
-DATA 4 0x021b0840 0x0306027E
-DATA 4 0x021b483c 0x43250330
-DATA 4 0x021b4840 0x0322027B
-DATA 4 0x021b0848 0x47414146
-DATA 4 0x021b4848 0x41434048
-DATA 4 0x021b0850 0x41444A44
-DATA 4 0x021b4850 0x4B444C46
-DATA 4 0x021b081c 0x33333333
-DATA 4 0x021b0820 0x33333333
-DATA 4 0x021b0824 0x33333333
-DATA 4 0x021b0828 0x33333333
-DATA 4 0x021b481c 0x33333333
-DATA 4 0x021b4820 0x33333333
-DATA 4 0x021b4824 0x33333333
-DATA 4 0x021b4828 0x33333333
-DATA 4 0x021b08b8 0x00000800
-DATA 4 0x021b48b8 0x00000800
-DATA 4 0x021b0004 0x00020036
-DATA 4 0x021b0008 0x09444040
-DATA 4 0x021b000c 0x555A79A4
-DATA 4 0x021b0010 0xDB538F64
-DATA 4 0x021b0014 0x01FF00DB
-DATA 4 0x021b0018 0x00081740
-DATA 4 0x021b001c 0x00008000
-DATA 4 0x021b002c 0x000026d2
-DATA 4 0x021b0030 0x005A0E21
-DATA 4 0x021b0040 0x00000027
-DATA 4 0x021b0000 0x831A0000
-DATA 4 0x021b001c 0x04888032
-DATA 4 0x021b001c 0x00008033
-DATA 4 0x021b001c 0x00428031
-DATA 4 0x021b001c 0x09308030
-DATA 4 0x021b001c 0x04008040
-DATA 4 0x021b001c 0x04008048
-DATA 4 0x021b0020 0x00005800
-DATA 4 0x021b0818 0x00011117
-DATA 4 0x021b4818 0x00011117
-DATA 4 0x021b0004 0x00025576
-DATA 4 0x021b0404 0x00011006
-DATA 4 0x021b001c 0x00000000
-
-/* set the default clock gate to save power */
-DATA 4 0x020c4068 0x00C03F3F
-DATA 4 0x020c406c 0x0030FC03
-DATA 4 0x020c4070 0x0FFFC000
-DATA 4 0x020c4074 0x3FF00000
-DATA 4 0x020c4078 0x00FFF300
-DATA 4 0x020c407c 0x0F0000C3
-DATA 4 0x020c4080 0x000003FF
-
-/* enable AXI cache for VDOA/VPU/IPU */
-DATA 4 0x020e0010 0xF00000CF
-/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
-DATA 4 0x020e0018 0x007F007F
-DATA 4 0x020e001c 0x007F007F
-
-/*
- * Setup CCM_CCOSR register as follows:
- *
- * cko1_en = 1 --> CKO1 enabled
- * cko1_div = 111 --> divide by 8
- * cko1_sel = 1011 --> ahb_clk_root
- *
- * This sets CKO1 at ahb_clk_root/8 = 132/8 = 16.5 MHz
- */
-DATA 4 0x020c4060 0x000000fb
diff --git a/configs/cgtqmx6qeval_defconfig b/configs/cgtqmx6eval_defconfig
similarity index 57%
rename from configs/cgtqmx6qeval_defconfig
rename to configs/cgtqmx6eval_defconfig
index fdbcc22..2765aa2 100644
--- a/configs/cgtqmx6qeval_defconfig
+++ b/configs/cgtqmx6eval_defconfig
@@ -1,10 +1,11 @@
CONFIG_ARM=y
CONFIG_ARCH_MX6=y
CONFIG_TARGET_CGTQMX6EVAL=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/congatec/cgtqmx6eval/imximage.cfg,MX6Q"
-CONFIG_SYS_PROMPT="CGT-QMX6-Quad U-Boot > "
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/imx-common/spl_sd.cfg,SPL,MX6QDL"
# CONFIG_CMD_IMLS is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_SETEXPR is not set
+CONFIG_SYS_PROMPT="CGT-QMX6 U-Boot > "
CONFIG_DM=y
CONFIG_DM_THERMAL=y
diff --git a/include/configs/cgtqmx6eval.h b/include/configs/cgtqmx6eval.h
index ee48fa6..d8eff10 100644
--- a/include/configs/cgtqmx6eval.h
+++ b/include/configs/cgtqmx6eval.h
@@ -17,6 +17,16 @@
#define CONFIG_MACH_TYPE 4122
+#ifdef CONFIG_SPL
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SYS_SPI_U_BOOT_OFFS (64 * 1024)
+#define CONFIG_SPL_SPI_LOAD
+#include "imx6_spl.h"
+#endif
+
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024)
@@ -144,10 +154,11 @@
#define CONFIG_MMCROOT "/dev/mmcblk0p2"
#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
#define CONFIG_EXTRA_ENV_SETTINGS \
"script=boot.scr\0" \
"image=zImage\0" \
- "fdtfile=imx6q-qmx6.dtb\0" \
+ "fdtfile=undefined\0" \
"fdt_addr_r=0x18000000\0" \
"boot_fdt=try\0" \
"ip_dyn=yes\0" \
@@ -192,6 +203,13 @@
"else " \
"bootz; " \
"fi;\0" \
+ "findfdt="\
+ "if test $board_rev = MX6Q ; then " \
+ "setenv fdtfile imx6q-qmx6.dtb; fi; " \
+ "if test $board_rev = MX6DL ; then " \
+ "setenv fdtfile imx6dl-qmx6.dtb; fi; " \
+ "if test $fdtfile = undefined; then " \
+ "echo WARNING: Could not determine dtb to use; fi; \0" \
"netargs=setenv bootargs console=${console},${baudrate} " \
"root=/dev/nfs " \
"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
@@ -220,6 +238,7 @@
#define CONFIG_BOOTCOMMAND \
"run spilock;" \
+ "run findfdt; " \
"mmc dev ${mmcdev};" \
"if mmc rescan; then " \
"if run loadbootscript; then " \
--
2.6.2
More information about the U-Boot
mailing list