[U-Boot] [PATCH 11/11] imx: mx7d: isolate resources to domain 0 for A7 core

Peng Fan van.freenix at gmail.com
Tue Jan 5 06:56:24 CET 2016


From: Peng Fan <peng.fan at nxp.com>

In current design, if any peripheral was assigned to both A7 and M4,
it will receive ipg_stop or ipg_wait when any of the 2 platforms
enter low power mode. We will have a risk that, if A7 enter wait,
M4 enter stop, peripheral will have chance to get ipg_stop and ipg_wait
asserted same time. Also if M4 enters stop mode, A7 will have no
chance to access the peripheral.
There are 26 peripherals impacted by this IC issue:
SIM2(sim2/emvsim2)
SIM1(sim1/emvsim1)
UART1/UART2/UART3/UART4/UART5/UART6/UART7
SAI1/SAI2/SAI3
WDOG1/WDOG2/WDOG3/WDOG4
GPT1/GPT2/GPT3/GPT4
PWM1/PWM2/PWM3/PWM4
ENET1/ENET2
Software Workaround:
The solution is set M4 to a different domain with A core.
So the peripherals are not shared by them. This way requires
the uboot implemented the RDC driver and set the 26 IPs above
to domain 0 only. M4 image will set the M4 to domain 1 and
set peripheral which it will use to domain 1.

This patch enables the CONFIG_IMX_RDC and CONFIG_IMX_BOOTAUX for
i.MX7D SABRESD board, and setup the 26 IP resources to domain 0.

Signed-off-by: Ye.Li <ye.li at nxp.com>
Signed-off-by: Peng Fan <peng.fan at nxp.com>
---
 arch/arm/cpu/armv7/mx7/soc.c  | 64 +++++++++++++++++++++++++++++++++++++++++++
 configs/mx7dsabresd_defconfig |  2 ++
 2 files changed, 66 insertions(+)

diff --git a/arch/arm/cpu/armv7/mx7/soc.c b/arch/arm/cpu/armv7/mx7/soc.c
index 2121ff2..ede7d53 100644
--- a/arch/arm/cpu/armv7/mx7/soc.c
+++ b/arch/arm/cpu/armv7/mx7/soc.c
@@ -12,6 +12,8 @@
 #include <asm/imx-common/boot_mode.h>
 #include <asm/imx-common/dma.h>
 #include <asm/imx-common/hab.h>
+#include <asm/imx-common/rdc-sema.h>
+#include <asm/arch/imx-rdc.h>
 #include <asm/arch/crm_regs.h>
 #include <dm.h>
 #include <imx_thermal.h>
@@ -29,6 +31,65 @@ U_BOOT_DEVICE(imx7_thermal) = {
 };
 #endif
 
+#ifdef CONFIG_IMX_RDC
+/*
+ * In current design, if any peripheral was assigned to both A7 and M4,
+ * it will receive ipg_stop or ipg_wait when any of the 2 platforms enter
+ * low power mode. So M4 sleep will cause some peripherals fail to work
+ * at A7 core side. At default, all resources are in domain 0 - 3.
+ *
+ * There are 26 peripherals impacted by this IC issue:
+ * SIM2(sim2/emvsim2)
+ * SIM1(sim1/emvsim1)
+ * UART1/UART2/UART3/UART4/UART5/UART6/UART7
+ * SAI1/SAI2/SAI3
+ * WDOG1/WDOG2/WDOG3/WDOG4
+ * GPT1/GPT2/GPT3/GPT4
+ * PWM1/PWM2/PWM3/PWM4
+ * ENET1/ENET2
+ * Software Workaround:
+ * Here we setup some resources to domain 0 where M4 codes will move
+ * the M4 out of this domain. Then M4 is not able to access them any longer.
+ * This is a workaround for ic issue. So the peripherals are not shared
+ * by them. This way requires the uboot implemented the RDC driver and
+ * set the 26 IPs above to domain 0 only. M4 code will assign resource
+ * to its own domain, if it want to use the resource.
+ */
+static rdc_peri_cfg_t const resources[] = {
+	(RDC_PER_SIM1 | RDC_DOMAIN(0)),
+	(RDC_PER_SIM2 | RDC_DOMAIN(0)),
+	(RDC_PER_UART1 | RDC_DOMAIN(0)),
+	(RDC_PER_UART2 | RDC_DOMAIN(0)),
+	(RDC_PER_UART3 | RDC_DOMAIN(0)),
+	(RDC_PER_UART4 | RDC_DOMAIN(0)),
+	(RDC_PER_UART5 | RDC_DOMAIN(0)),
+	(RDC_PER_UART6 | RDC_DOMAIN(0)),
+	(RDC_PER_UART7 | RDC_DOMAIN(0)),
+	(RDC_PER_SAI1 | RDC_DOMAIN(0)),
+	(RDC_PER_SAI2 | RDC_DOMAIN(0)),
+	(RDC_PER_SAI3 | RDC_DOMAIN(0)),
+	(RDC_PER_WDOG1 | RDC_DOMAIN(0)),
+	(RDC_PER_WDOG2 | RDC_DOMAIN(0)),
+	(RDC_PER_WDOG3 | RDC_DOMAIN(0)),
+	(RDC_PER_WDOG4 | RDC_DOMAIN(0)),
+	(RDC_PER_GPT1 | RDC_DOMAIN(0)),
+	(RDC_PER_GPT2 | RDC_DOMAIN(0)),
+	(RDC_PER_GPT3 | RDC_DOMAIN(0)),
+	(RDC_PER_GPT4 | RDC_DOMAIN(0)),
+	(RDC_PER_PWM1 | RDC_DOMAIN(0)),
+	(RDC_PER_PWM2 | RDC_DOMAIN(0)),
+	(RDC_PER_PWM3 | RDC_DOMAIN(0)),
+	(RDC_PER_PWM4 | RDC_DOMAIN(0)),
+	(RDC_PER_ENET1 | RDC_DOMAIN(0)),
+	(RDC_PER_ENET2 | RDC_DOMAIN(0)),
+};
+
+static void isolate_resource(void)
+{
+	imx_rdc_setup_peripherals(resources, ARRAY_SIZE(resources));
+}
+#endif
+
 #if defined(CONFIG_SECURE_BOOT)
 struct imx_sec_config_fuse_t const imx_sec_config_fuse = {
 	.bank = 1,
@@ -163,6 +224,9 @@ int arch_cpu_init(void)
 	mxs_dma_init();
 #endif
 
+	if (IS_ENABLED(CONFIG_IMX_RDC))
+		isolate_resource();
+
 	return 0;
 }
 
diff --git a/configs/mx7dsabresd_defconfig b/configs/mx7dsabresd_defconfig
index 420d13e..1d262c1 100644
--- a/configs/mx7dsabresd_defconfig
+++ b/configs/mx7dsabresd_defconfig
@@ -1,6 +1,8 @@
 CONFIG_ARM=y
 CONFIG_ARCH_MX7=y
 CONFIG_TARGET_MX7DSABRESD=y
+CONFIG_IMX_RDC=y
+CONFIG_IMX_BOOTAUX=y
 CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx7dsabresd/imximage.cfg,MX7D"
 # CONFIG_CMD_BOOTD is not set
 # CONFIG_CMD_IMI is not set
-- 
2.6.2



More information about the U-Boot mailing list