[U-Boot] [PATCH 5/5] sunxi: power: axp818: Enable support for ALDOs

[Chen-Yu Tsai]

Previously, AXP818 ALDO support was partially added to Kconfig, but
never enabled in the board file, nor properly set or configured in
Kconfig. The boards continue to work because the AXP818 is designed
to pair with the A83T/H8, and the default voltages match the reference
design's requirements.

Signed-off-by: Chen-Yu Tsai <wens at csie.org>
---
 board/sunxi/board.c    |  8 +++-----
 drivers/power/Kconfig  | 13 ++++++++++---
 drivers/power/axp818.c | 37 +++++++++++++++++++++++++++++++++++++
 3 files changed, 50 insertions(+), 8 deletions(-)

diff --git a/board/sunxi/board.c b/board/sunxi/board.c
index 85f01fd..e0ff650 100644
--- a/board/sunxi/board.c
+++ b/board/sunxi/board.c
@@ -446,20 +446,18 @@ void sunxi_board_init(void)
 	power_failed |= axp_set_dcdc5(CONFIG_AXP_DCDC5_VOLT);
 #endif
 
-#ifdef CONFIG_AXP221_POWER
+#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP818_POWER
 	power_failed |= axp_set_aldo1(CONFIG_AXP_ALDO1_VOLT);
 #endif
-#ifndef CONFIG_AXP818_POWER
 	power_failed |= axp_set_aldo2(CONFIG_AXP_ALDO2_VOLT);
-#endif
-#if !defined(CONFIG_AXP152_POWER) && !defined(CONFIG_AXP818_POWER)
+#if !defined(CONFIG_AXP152_POWER)
 	power_failed |= axp_set_aldo3(CONFIG_AXP_ALDO3_VOLT);
 #endif
 #ifdef CONFIG_AXP209_POWER
 	power_failed |= axp_set_aldo4(CONFIG_AXP_ALDO4_VOLT);
 #endif
 
-#ifdef CONFIG_AXP221_POWER
+#if defined(CONFIG_AXP221_POWER) || defined(CONFIG_AXP818_POWER)
 	power_failed |= axp_set_dldo(1, CONFIG_AXP_DLDO1_VOLT);
 	power_failed |= axp_set_dldo(2, CONFIG_AXP_DLDO2_VOLT);
 	power_failed |= axp_set_dldo(3, CONFIG_AXP_DLDO3_VOLT);
diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig
index 6f61763..e91a5c0 100644
--- a/drivers/power/Kconfig
+++ b/drivers/power/Kconfig
@@ -118,20 +118,24 @@ config AXP_DCDC5_VOLT
 
 config AXP_ALDO1_VOLT
 	int "axp pmic (a)ldo1 voltage"
-	depends on AXP221_POWER
+	depends on AXP221_POWER || AXP818_POWER
 	default 0 if MACH_SUN6I
+	default 1800 if MACH_SUN8I_A83T
 	default 3000 if MACH_SUN8I
 	---help---
 	Set the voltage (mV) to program the axp pmic aldo1 at, set to 0 to
 	disable aldo1.
 	On A31 boards aldo1 is often used to power the wifi module.
 	On A23 / A33 boards aldo1 is used for VCC-IO and should be 3.0V.
+	On A83T / H8 boards aldo1 is used for MIPI CSI, DSI, HDMI, EFUSE, and
+	should be 1.8V.
 
 config AXP_ALDO2_VOLT
 	int "axp pmic (a)ldo2 voltage"
 	depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP818_POWER
 	default 3000 if AXP152_POWER || AXP209_POWER
 	default 0 if MACH_SUN6I
+	default 1800 if MACH_SUN8I_A83T
 	default 2500 if MACH_SUN8I
 	---help---
 	Set the voltage (mV) to program the axp pmic aldo2 at, set to 0 to
@@ -140,18 +144,21 @@ config AXP_ALDO2_VOLT
 	On A31 boards aldo2 is typically unused and should be disabled.
 	On A31 boards aldo2 may be used for LPDDR2 then it should be 1.8V.
 	On A23 / A33 boards aldo2 is used for VDD-DLL and should be 2.5V.
+	On A83T / H8 boards aldo2 powers VDD-DLL, VCC18-PLL, CPVDD, VDD18-ADC,
+	LPDDR2, and the codec. It should be 1.8V.
 
 config AXP_ALDO3_VOLT
 	int "axp pmic (a)ldo3 voltage"
 	depends on AXP209_POWER || AXP221_POWER || AXP818_POWER
-	default 0 if AXP209_POWER || AXP818_POWER
+	default 0 if AXP209_POWER
 	default 3000 if MACH_SUN6I || MACH_SUN8I
 	---help---
 	Set the voltage (mV) to program the axp pmic aldo3 at, set to 0 to
 	disable aldo3.
 	On A10(s) / A13 / A20 boards aldo3 should be 2.8V.
 	On A23 / A31 / A33 boards aldo3 is VCC-PLL and AVCC and should be 3.0V.
-	On A83T aldo3 is used for LVDS, DSI, MIPI, HDMI, etc.
+	On A83T / H8 boards aldo3 is AVCC, VCC-PL, and VCC-LED, and should be
+	3.0V.
 
 config AXP_ALDO4_VOLT
 	int "axp pmic (a)ldo4 voltage"
diff --git a/drivers/power/axp818.c b/drivers/power/axp818.c
index 3119b64..e885d02 100644
--- a/drivers/power/axp818.c
+++ b/drivers/power/axp818.c
@@ -110,6 +110,43 @@ int axp_set_dcdc5(unsigned int mvolt)
 				AXP818_OUTPUT_CTRL1_DCDC5_EN);
 }
 
+int axp_set_aldo(int aldo_num, unsigned int mvolt)
+{
+	int ret;
+	u8 cfg;
+
+	if (aldo_num < 1 || aldo_num > 3)
+		return -EINVAL;
+
+	if (mvolt == 0)
+		return pmic_bus_clrbits(AXP818_OUTPUT_CTRL3,
+				AXP818_OUTPUT_CTRL3_ALDO1_EN << (aldo_num - 1));
+
+	cfg = axp818_mvolt_to_cfg(mvolt, 700, 3300, 100);
+	ret = pmic_bus_write(AXP818_ALDO1_CTRL + (aldo_num - 1), cfg);
+	if (ret)
+		return ret;
+
+	return pmic_bus_setbits(AXP818_OUTPUT_CTRL3,
+				AXP818_OUTPUT_CTRL3_ALDO1_EN << (aldo_num - 1));
+}
+
+/* TODO: re-work other AXP drivers to consolidate ALDO functions. */
+int axp_set_aldo1(unsigned int mvolt)
+{
+	return axp_set_aldo(1, mvolt);
+}
+
+int axp_set_aldo2(unsigned int mvolt)
+{
+	return axp_set_aldo(2, mvolt);
+}
+
+int axp_set_aldo3(unsigned int mvolt)
+{
+	return axp_set_aldo(3, mvolt);
+}
+
 int axp_set_dldo(int dldo_num, unsigned int mvolt)
 {
 	int ret;
-- 
2.6.4