[U-Boot] [PATCH v3 07/14] drivers: ddr: Add DDR2 SDRAM controller driver for Microchip PIC32.
Purna Chandra Mandal
purna.mandal at microchip.com
Tue Jan 12 11:18:22 CET 2016
This driver initializes PIC32 DDR2 SDRAM controller and internal DDR2 Phy module.
DDR2 controller operates in half-rate mode (upto 533MHZ frequency).
Signed-off-by: Paul Thacker <paul.thacker at microchip.com>
Signed-off-by: Purna Chandra Mandal <purna.mandal at microchip.com>
---
Changes in v3:
- annotating fixed table with const
- fix camel-case in ddr2 timing parameters
- fix cmd index parameter of host_load_cmd().
- fix compilation warning
Changes in v2:
- move ddr2 initialization from board/microchip/ to drivers/ddr/microchip
arch/mips/mach-pic32/include/mach/ddr.h | 32 ++++
drivers/Makefile | 1 +
drivers/ddr/microchip/Makefile | 6 +
drivers/ddr/microchip/ddr2.c | 278 ++++++++++++++++++++++++++++++++
drivers/ddr/microchip/ddr2_regs.h | 148 +++++++++++++++++
drivers/ddr/microchip/ddr2_timing.h | 65 ++++++++
6 files changed, 530 insertions(+)
create mode 100644 arch/mips/mach-pic32/include/mach/ddr.h
create mode 100644 drivers/ddr/microchip/Makefile
create mode 100644 drivers/ddr/microchip/ddr2.c
create mode 100644 drivers/ddr/microchip/ddr2_regs.h
create mode 100644 drivers/ddr/microchip/ddr2_timing.h
diff --git a/arch/mips/mach-pic32/include/mach/ddr.h b/arch/mips/mach-pic32/include/mach/ddr.h
new file mode 100644
index 0000000..00abfa3
--- /dev/null
+++ b/arch/mips/mach-pic32/include/mach/ddr.h
@@ -0,0 +1,32 @@
+/*
+ * (c) 2015 Purna Chandra Mandal <purna.mandal at microchip.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ */
+
+#ifndef __MICROCHIP_PIC32_DDR_H
+#define __MICROCHIP_PIC32_DDR_H
+
+/* called by initdram() function */
+void ddr2_phy_init(void);
+void ddr2_ctrl_init(void);
+phys_size_t ddr2_calculate_size(void);
+
+/* Maximum number of agents */
+#define NUM_AGENTS 5
+
+/* Board can provide agent specific parameters for arbitration by
+ * filling struct ddr2_arbiter_params for all the agents and
+ * implementing board_get_ddr_arbiter_params() to return the filled
+ * structure.
+ */
+struct ddr2_arbiter_params {
+ u32 min_limit; /* min bursts to execute per arbitration */
+ u32 req_period; /* request period threshold for accepted cmds */
+ u32 min_cmd_acpt; /* min number of accepted cmds */
+};
+
+const struct ddr2_arbiter_params *board_get_ddr_arbiter_params(void);
+
+#endif /* __MICROCHIP_PIC32_DDR_H */
diff --git a/drivers/Makefile b/drivers/Makefile
index c9031f2..0ab54d9 100644
--- a/drivers/Makefile
+++ b/drivers/Makefile
@@ -68,4 +68,5 @@ obj-y += soc/
obj-$(CONFIG_REMOTEPROC) += remoteproc/
obj-y += thermal/
+obj-$(CONFIG_MACH_PIC32) += ddr/microchip/
endif
diff --git a/drivers/ddr/microchip/Makefile b/drivers/ddr/microchip/Makefile
new file mode 100644
index 0000000..305c48b
--- /dev/null
+++ b/drivers/ddr/microchip/Makefile
@@ -0,0 +1,6 @@
+#
+# Copyright (C) 2015 Microchip Technology Inc.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+obj-$(CONFIG_MACH_PIC32) += ddr2.o
diff --git a/drivers/ddr/microchip/ddr2.c b/drivers/ddr/microchip/ddr2.c
new file mode 100644
index 0000000..6056418
--- /dev/null
+++ b/drivers/ddr/microchip/ddr2.c
@@ -0,0 +1,278 @@
+/*
+ * (c) 2015 Paul Thacker <paul.thacker at microchip.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ */
+#include <common.h>
+#include <wait_bit.h>
+#include <linux/kernel.h>
+#include <linux/bitops.h>
+#include <mach/pic32.h>
+#include <mach/ddr.h>
+
+#include "ddr2_regs.h"
+#include "ddr2_timing.h"
+
+/* init DDR2 Phy */
+void ddr2_phy_init(void)
+{
+ struct ddr2_phy_regs *ddr2_phy;
+ u32 pad_ctl;
+
+ ddr2_phy = ioremap(PIC32_DDR2P_BASE, sizeof(*ddr2_phy));
+
+ /* PHY_DLL_RECALIB */
+ writel(DELAY_START_VAL(3) | DISABLE_RECALIB(0) |
+ RECALIB_CNT(0x10), &ddr2_phy->dll_recalib);
+
+ /* PHY_PAD_CTRL */
+ pad_ctl = ODT_SEL | ODT_EN | DRIVE_SEL(0) |
+ ODT_PULLDOWN(2) | ODT_PULLUP(3) |
+ EXTRA_OEN_CLK(0) | NOEXT_DLL |
+ DLR_DFT_WRCMD | HALF_RATE |
+ DRVSTR_PFET(0xe) | DRVSTR_NFET(0xe) |
+ RCVR_EN | PREAMBLE_DLY(2);
+ writel(pad_ctl, &ddr2_phy->pad_ctrl);
+
+ /* SCL_CONFIG_0 */
+ writel(SCL_BURST8 | SCL_DDR_CONNECTED | SCL_RCAS_LAT(RL) |
+ SCL_ODTCSWW, &ddr2_phy->scl_config_1);
+
+ /* SCL_CONFIG_1 */
+ writel(SCL_CSEN | SCL_WCAS_LAT(WL), &ddr2_phy->scl_config_2);
+
+ /* SCL_LAT */
+ writel(SCL_CAPCLKDLY(3) | SCL_DDRCLKDLY(4), &ddr2_phy->scl_latency);
+}
+
+/* start phy self calibration logic */
+static int ddr2_phy_calib_start(void)
+{
+ struct ddr2_phy_regs *ddr2_phy;
+
+ ddr2_phy = ioremap(PIC32_DDR2P_BASE, sizeof(*ddr2_phy));
+
+ /* DDR Phy SCL Start */
+ writel(SCL_START | SCL_EN, &ddr2_phy->scl_start);
+
+ /* Wait for SCL for data byte to pass */
+ return wait_for_bit(__func__, &ddr2_phy->scl_start, SCL_LUBPASS,
+ true, CONFIG_SYS_HZ, false);
+}
+
+/* DDR2 Controller initialization */
+
+/* Target Agent Arbiter */
+static void ddr_set_arbiter(struct ddr2_ctrl_regs *ctrl,
+ const struct ddr2_arbiter_params *const param)
+{
+ int i;
+
+ for (i = 0; i < NUM_AGENTS; i++) {
+ /* set min burst size */
+ writel(i * MIN_LIM_WIDTH, &ctrl->tsel);
+ writel(param->min_limit, &ctrl->minlim);
+
+ /* set request period (4 * req_period clocks) */
+ writel(i * RQST_PERIOD_WIDTH, &ctrl->tsel);
+ writel(param->req_period, &ctrl->reqprd);
+
+ /* set number of burst accepted */
+ writel(i * MIN_CMDACPT_WIDTH, &ctrl->tsel);
+ writel(param->min_cmd_acpt, &ctrl->mincmd);
+ }
+}
+
+const struct ddr2_arbiter_params *__weak board_get_ddr_arbiter_params(void)
+{
+ /* default arbiter parameters */
+ static const struct ddr2_arbiter_params arb_params[] = {
+ { .min_limit = 0x1f, .req_period = 0xff, .min_cmd_acpt = 0x04,},
+ { .min_limit = 0x1f, .req_period = 0xff, .min_cmd_acpt = 0x10,},
+ { .min_limit = 0x1f, .req_period = 0xff, .min_cmd_acpt = 0x10,},
+ { .min_limit = 0x04, .req_period = 0xff, .min_cmd_acpt = 0x04,},
+ { .min_limit = 0x04, .req_period = 0xff, .min_cmd_acpt = 0x04,},
+ };
+
+ return &arb_params[0];
+}
+
+static void host_load_cmd(struct ddr2_ctrl_regs *ctrl, u32 cmd_idx,
+ u32 hostcmd2, u32 hostcmd1, u32 delay)
+{
+ u32 hc_delay;
+
+ hc_delay = max_t(u32, DIV_ROUND_UP(delay, T_CK), 2) - 2;
+ writel(hostcmd1, &ctrl->cmd10[cmd_idx]);
+ writel((hostcmd2 & 0x7ff) | (hc_delay << 11), &ctrl->cmd20[cmd_idx]);
+}
+
+/* init DDR2 Controller */
+void ddr2_ctrl_init(void)
+{
+ u32 wr2prech, rd2prech, wr2rd, wr2rd_cs;
+ u32 ras2ras, ras2cas, prech2ras, temp;
+ const struct ddr2_arbiter_params *arb_params;
+ struct ddr2_ctrl_regs *ctrl;
+
+ ctrl = ioremap(PIC32_DDR2C_BASE, sizeof(*ctrl));
+
+ /* PIC32 DDR2 controller always work in HALF_RATE */
+ writel(HALF_RATE_MODE, &ctrl->memwidth);
+
+ /* Set arbiter configuration per target */
+ arb_params = board_get_ddr_arbiter_params();
+ ddr_set_arbiter(ctrl, arb_params);
+
+ /* Address Configuration, model {CS, ROW, BA, COL} */
+ writel((ROW_ADDR_RSHIFT | (BA_RSHFT << 8) | (CS_ADDR_RSHIFT << 16) |
+ (COL_HI_RSHFT << 24) | (SB_PRI << 29) |
+ (EN_AUTO_PRECH << 30)), &ctrl->memcfg0);
+
+ writel(ROW_ADDR_MASK, &ctrl->memcfg1);
+ writel(COL_HI_MASK, &ctrl->memcfg2);
+ writel(COL_LO_MASK, &ctrl->memcfg3);
+ writel(BA_MASK | (CS_ADDR_MASK << 8), &ctrl->memcfg4);
+
+ /* Refresh Config */
+ writel(REFCNT_CLK(DIV_ROUND_UP(T_RFI, T_CK_CTRL) - 2) |
+ REFDLY_CLK(DIV_ROUND_UP(T_RFC_MIN, T_CK_CTRL) - 2) |
+ MAX_PEND_REF(7),
+ &ctrl->refcfg);
+
+ /* Power Config */
+ writel(ECC_EN(0) | ERR_CORR_EN(0) | EN_AUTO_PWR_DN(0) |
+ EN_AUTO_SELF_REF(3) | PWR_DN_DLY(8) |
+ SELF_REF_DLY(17) | PRECH_PWR_DN_ONLY(0),
+ &ctrl->pwrcfg);
+
+ /* Delay Config */
+ wr2rd = max_t(u32, DIV_ROUND_UP(T_WTR, T_CK_CTRL),
+ DIV_ROUND_UP(T_WTR_TCK, 2)) + WL + BL;
+ wr2rd_cs = max_t(u32, wr2rd - 1, 3);
+ wr2prech = DIV_ROUND_UP(T_WR, T_CK_CTRL) + WL + BL;
+ rd2prech = max_t(u32, DIV_ROUND_UP(T_RTP, T_CK_CTRL),
+ DIV_ROUND_UP(T_RTP_TCK, 2)) + BL - 2;
+ ras2ras = max_t(u32, DIV_ROUND_UP(T_RRD, T_CK_CTRL),
+ DIV_ROUND_UP(T_RRD_TCK, 2)) - 1;
+ ras2cas = DIV_ROUND_UP(T_RCD, T_CK_CTRL) - 1;
+ prech2ras = DIV_ROUND_UP(T_RP, T_CK_CTRL) - 1;
+
+ writel(((wr2rd & 0x0f) |
+ ((wr2rd_cs & 0x0f) << 4) |
+ ((BL - 1) << 8) |
+ (BL << 12) |
+ ((BL - 1) << 16) |
+ ((BL - 1) << 20) |
+ ((BL + 2) << 24) |
+ ((RL - WL + 3) << 28)), &ctrl->dlycfg0);
+
+ writel(((T_CKE_TCK - 1) |
+ (((DIV_ROUND_UP(T_DLLK, 2) - 2) & 0xff) << 8) |
+ ((T_CKE_TCK - 1) << 16) |
+ ((max_t(u32, T_XP_TCK, T_CKE_TCK) - 1) << 20) |
+ ((wr2prech >> 4) << 26) |
+ ((wr2rd >> 4) << 27) |
+ ((wr2rd_cs >> 4) << 28) |
+ (((RL + 5) >> 4) << 29) |
+ ((DIV_ROUND_UP(T_DLLK, 2) >> 8) << 30)), &ctrl->dlycfg1);
+
+ writel((DIV_ROUND_UP(T_RP, T_CK_CTRL) |
+ (rd2prech << 8) |
+ ((wr2prech & 0x0f) << 12) |
+ (ras2ras << 16) |
+ (ras2cas << 20) |
+ (prech2ras << 24) |
+ ((RL + 3) << 28)), &ctrl->dlycfg2);
+
+ writel(((DIV_ROUND_UP(T_RAS_MIN, T_CK_CTRL) - 1) |
+ ((DIV_ROUND_UP(T_RC, T_CK_CTRL) - 1) << 8) |
+ ((DIV_ROUND_UP(T_FAW, T_CK_CTRL) - 1) << 16)),
+ &ctrl->dlycfg3);
+
+ /* ODT Config */
+ writel(0x0, &ctrl->odtcfg);
+ writel(BIT(16), &ctrl->odtencfg);
+ writel(ODTRDLY(RL - 3) | ODTWDLY(WL - 3) | ODTRLEN(2) | ODTWLEN(3),
+ &ctrl->odtcfg);
+
+ /* Transfer Configuration */
+ writel(NXTDATRQDLY(2) | NXDATAVDLY(4) | RDATENDLY(2) |
+ MAX_BURST(3) | (7 << 28) | BIG_ENDIAN(0),
+ &ctrl->xfercfg);
+
+ /* DRAM Initialization */
+ /* CKE high after reset and wait 400 nsec */
+ host_load_cmd(ctrl, 0, 0, IDLE_NOP, 400000);
+
+ /* issue precharge all command */
+ host_load_cmd(ctrl, 1, 0x04, PRECH_ALL_CMD, T_RP + T_CK);
+
+ /* initialize EMR2 */
+ host_load_cmd(ctrl, 2, 0x200, LOAD_MODE_CMD, T_MRD_TCK * T_CK);
+
+ /* initialize EMR3 */
+ host_load_cmd(ctrl, 3, 0x300, LOAD_MODE_CMD, T_MRD_TCK * T_CK);
+
+ /*
+ * RDQS disable, DQSB enable, OCD exit, 150 ohm termination,
+ * AL=0, DLL enable
+ */
+ host_load_cmd(ctrl, 4, 0x100,
+ LOAD_MODE_CMD | (0x40 << 24), T_MRD_TCK * T_CK);
+ /*
+ * PD fast exit, WR REC = T_WR in clocks -1,
+ * DLL reset, CAS = RL, burst = 4
+ */
+ temp = ((DIV_ROUND_UP(T_WR, T_CK) - 1) << 1) | 1;
+ host_load_cmd(ctrl, 5, temp, LOAD_MODE_CMD | (RL << 28) | (2 << 24),
+ T_MRD_TCK * T_CK);
+
+ /* issue precharge all command */
+ host_load_cmd(ctrl, 6, 4, PRECH_ALL_CMD, T_RP + T_CK);
+
+ /* issue refresh command */
+ host_load_cmd(ctrl, 7, 0, REF_CMD, T_RFC_MIN);
+
+ /* issue refresh command */
+ host_load_cmd(ctrl, 8, 0, REF_CMD, T_RFC_MIN);
+
+ /* Mode register programming as before without DLL reset */
+ host_load_cmd(ctrl, 9, temp, LOAD_MODE_CMD | (RL << 28) | (3 << 24),
+ T_MRD_TCK * T_CK);
+
+ /* extended mode register same as before with OCD default */
+ host_load_cmd(ctrl, 10, 0x103, LOAD_MODE_CMD | (0xc << 24),
+ T_MRD_TCK * T_CK);
+
+ /* extended mode register same as before with OCD exit */
+ host_load_cmd(ctrl, 11, 0x100, LOAD_MODE_CMD | (0x4 << 28),
+ 140 * T_CK);
+
+ writel(CMD_VALID | NUMHOSTCMD(11), &ctrl->cmdissue);
+
+ /* start memory initialization */
+ writel(INIT_START, &ctrl->memcon);
+
+ /* wait for all host cmds to be transmitted */
+ wait_for_bit(__func__, &ctrl->cmdissue, CMD_VALID, false,
+ CONFIG_SYS_HZ, false);
+
+ /* inform all cmds issued, ready for normal operation */
+ writel(INIT_START | INIT_DONE, &ctrl->memcon);
+
+ /* perform phy caliberation */
+ if (ddr2_phy_calib_start())
+ printf("ddr2: phy calib failed\n");
+}
+
+phys_size_t ddr2_calculate_size(void)
+{
+ u32 temp;
+
+ temp = 1 << (COL_BITS + BA_BITS + ROW_BITS);
+ /* 16-bit data width between controller and DIMM */
+ temp = temp * CS_BITS * (16 / 8);
+ return (phys_size_t)temp;
+}
diff --git a/drivers/ddr/microchip/ddr2_regs.h b/drivers/ddr/microchip/ddr2_regs.h
new file mode 100644
index 0000000..0f4b159
--- /dev/null
+++ b/drivers/ddr/microchip/ddr2_regs.h
@@ -0,0 +1,148 @@
+/*
+ * (c) 2015 Purna Chandra Mandal <purna.mandal at microchip.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ */
+
+#ifndef __MICROCHIP_DDR2_REGS_H
+#define __MICROCHIP_DDR2_REGS_H
+
+#include <linux/bitops.h>
+
+/* DDR2 Controller */
+struct ddr2_ctrl_regs {
+ u32 tsel;
+ u32 minlim;
+ u32 reqprd;
+ u32 mincmd;
+ u32 memcon;
+ u32 memcfg0;
+ u32 memcfg1;
+ u32 memcfg2;
+ u32 memcfg3;
+ u32 memcfg4;
+ u32 refcfg;
+ u32 pwrcfg;
+ u32 dlycfg0;
+ u32 dlycfg1;
+ u32 dlycfg2;
+ u32 dlycfg3;
+ u32 odtcfg;
+ u32 xfercfg;
+ u32 cmdissue;
+ u32 odtencfg;
+ u32 memwidth;
+ u32 unused[11];
+ u32 cmd10[16];
+ u32 cmd20[16];
+};
+
+/* Arbiter Config */
+#define MIN_LIM_WIDTH 5
+#define RQST_PERIOD_WIDTH 8
+#define MIN_CMDACPT_WIDTH 8
+
+/* Refresh Config */
+#define REFCNT_CLK(x) (x)
+#define REFDLY_CLK(x) ((x) << 16)
+#define MAX_PEND_REF(x) ((x) << 24)
+
+/* Power Config */
+#define PRECH_PWR_DN_ONLY(x) ((x) << 22)
+#define SELF_REF_DLY(x) ((x) << 12)
+#define PWR_DN_DLY(x) ((x) << 4)
+#define EN_AUTO_SELF_REF(x) ((x) << 3)
+#define EN_AUTO_PWR_DN(x) ((x) << 2)
+#define ERR_CORR_EN(x) ((x) << 1)
+#define ECC_EN(x) (x)
+
+/* Memory Width */
+#define HALF_RATE_MODE BIT(3)
+
+/* Delay Config */
+#define ODTWLEN(x) ((x) << 20)
+#define ODTRLEN(x) ((x) << 16)
+#define ODTWDLY(x) ((x) << 12)
+#define ODTRDLY(x) ((x) << 8)
+
+/* Xfer Config */
+#define BIG_ENDIAN(x) ((x) << 31)
+#define MAX_BURST(x) ((x) << 24)
+#define RDATENDLY(x) ((x) << 16)
+#define NXDATAVDLY(x) ((x) << 4)
+#define NXTDATRQDLY(x) ((x) << 0)
+
+/* Host Commands */
+#define IDLE_NOP 0x00ffffff
+#define PRECH_ALL_CMD 0x00fff401
+#define REF_CMD 0x00fff801
+#define LOAD_MODE_CMD 0x00fff001
+#define CKE_LOW 0x00ffeffe
+
+#define NUM_HOST_CMDS 12
+
+/* Host CMD Issue */
+#define CMD_VALID BIT(4)
+#define NUMHOSTCMD(x) (x)
+
+/* Memory Control */
+#define INIT_DONE BIT(1)
+#define INIT_START BIT(0)
+
+/* Address Control */
+#define EN_AUTO_PRECH 0
+#define SB_PRI 1
+
+/* DDR2 Phy Register */
+struct ddr2_phy_regs {
+ u32 scl_start;
+ u32 unused1[2];
+ u32 scl_latency;
+ u32 unused2[2];
+ u32 scl_config_1;
+ u32 scl_config_2;
+ u32 pad_ctrl;
+ u32 dll_recalib;
+};
+
+/* PHY PAD CONTROL */
+#define ODT_SEL BIT(0)
+#define ODT_EN BIT(1)
+#define DRIVE_SEL(x) ((x) << 2)
+#define ODT_PULLDOWN(x) ((x) << 4)
+#define ODT_PULLUP(x) ((x) << 6)
+#define EXTRA_OEN_CLK(x) ((x) << 8)
+#define NOEXT_DLL BIT(9)
+#define DLR_DFT_WRCMD BIT(13)
+#define HALF_RATE BIT(14)
+#define DRVSTR_PFET(x) ((x) << 16)
+#define DRVSTR_NFET(x) ((x) << 20)
+#define RCVR_EN BIT(28)
+#define PREAMBLE_DLY(x) ((x) << 29)
+
+/* PHY DLL RECALIBRATE */
+#define RECALIB_CNT(x) ((x) << 8)
+#define DISABLE_RECALIB(x) ((x) << 26)
+#define DELAY_START_VAL(x) ((x) << 28)
+
+/* PHY SCL CONFIG1 */
+#define SCL_BURST8 BIT(0)
+#define SCL_DDR_CONNECTED BIT(1)
+#define SCL_RCAS_LAT(x) ((x) << 4)
+#define SCL_ODTCSWW BIT(24)
+
+/* PHY SCL CONFIG2 */
+#define SCL_CSEN BIT(0)
+#define SCL_WCAS_LAT(x) ((x) << 8)
+
+/* PHY SCL Latency */
+#define SCL_CAPCLKDLY(x) ((x) << 0)
+#define SCL_DDRCLKDLY(x) ((x) << 4)
+
+/* PHY SCL START */
+#define SCL_START BIT(28)
+#define SCL_EN BIT(26)
+#define SCL_LUBPASS (BIT(1) | BIT(0))
+
+#endif /* __MICROCHIP_DDR2_REGS_H */
diff --git a/drivers/ddr/microchip/ddr2_timing.h b/drivers/ddr/microchip/ddr2_timing.h
new file mode 100644
index 0000000..5895f9d
--- /dev/null
+++ b/drivers/ddr/microchip/ddr2_timing.h
@@ -0,0 +1,65 @@
+/*
+ * (c) 2015 Purna Chandra Mandal <purna.mandal at microchip.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ */
+
+#ifndef __MICROCHIP_DDR2_TIMING_H
+#define __MICROCHIP_DDR2_TIMING_H
+
+/* MPLL freq is 400MHz */
+#define T_CK 2500 /* 2500 psec */
+#define T_CK_CTRL (T_CK * 2)
+
+/* Burst length in cycles */
+#define BL 2
+/* default CAS latency for all speed grades */
+#define RL 5
+/* default write latency for all speed grades = CL-1 */
+#define WL 4
+
+/* From Micron MT47H64M16HR-3 data sheet */
+#define T_RFC_MIN 127500 /* psec */
+#define T_WR 15000 /* psec */
+#define T_RP 12500 /* psec */
+#define T_RCD 12500 /* psec */
+#define T_RRD 7500 /* psec */
+/* T_RRD_TCK is minimum of 2 clk periods, regardless of freq */
+#define T_RRD_TCK 2
+#define T_WTR 7500 /* psec */
+/* T_WTR_TCK is minimum of 2 clk periods, regardless of freq */
+#define T_WTR_TCK 2
+#define T_RTP 7500 /* psec */
+#define T_RTP_TCK (BL / 2)
+#define T_XP_TCK 2 /* clocks */
+#define T_CKE_TCK 3 /* clocks */
+#define T_XSNR (T_RFC_MIN + 10000) /* psec */
+#define T_DLLK 200 /* clocks */
+#define T_RAS_MIN 45000 /* psec */
+#define T_RC 57500 /* psec */
+#define T_FAW 35000 /* psec */
+#define T_MRD_TCK 2 /* clocks */
+#define T_RFI 7800000 /* psec */
+
+/* DDR Addressing */
+#define COL_BITS 10
+#define BA_BITS 3
+#define ROW_BITS 13
+#define CS_BITS 1
+
+/* DDR Addressing scheme: {CS, ROW, BA, COL} */
+#define COL_HI_RSHFT 0
+#define COL_HI_MASK 0
+#define COL_LO_MASK ((1 << COL_BITS) - 1)
+
+#define BA_RSHFT COL_BITS
+#define BA_MASK ((1 << BA_BITS) - 1)
+
+#define ROW_ADDR_RSHIFT (BA_RSHFT + BA_BITS)
+#define ROW_ADDR_MASK ((1 << ROW_BITS) - 1)
+
+#define CS_ADDR_RSHIFT 0
+#define CS_ADDR_MASK 0
+
+#endif /* __MICROCHIP_DDR2_TIMING_H */
--
1.8.3.1
More information about the U-Boot
mailing list