[U-Boot] [PATCH 25/25] exynos: video: Drop old unused code
Simon Glass
sjg at chromium.org
Fri Jan 15 01:00:14 CET 2016
Now that we are using driver model, we can drop the weak functions and LCD
init in the board file.
Signed-off-by: Simon Glass <sjg at chromium.org>
---
board/samsung/common/exynos5-dt.c | 153 --------------------------------------
drivers/video/exynos/exynos_fb.c | 33 --------
drivers/video/exynos/exynos_fb.h | 41 ----------
3 files changed, 227 deletions(-)
delete mode 100644 drivers/video/exynos/exynos_fb.h
diff --git a/board/samsung/common/exynos5-dt.c b/board/samsung/common/exynos5-dt.c
index 0dcea71..2e3b16d 100644
--- a/board/samsung/common/exynos5-dt.c
+++ b/board/samsung/common/exynos5-dt.c
@@ -147,159 +147,6 @@ int board_get_revision(void)
return 0;
}
-#ifdef CONFIG_LCD
-
-static int board_dp_bridge_init(struct udevice *dev)
-{
- const int max_tries = 10;
- int num_tries;
- int ret;
-
- debug("%s\n", __func__);
- ret = video_bridge_attach(dev);
- if (ret) {
- debug("video bridge init failed: %d\n", ret);
- return ret;
- }
-
- /*
- * We need to wait for 90ms after bringing up the bridge since there
- * is a phantom "high" on the HPD chip during its bootup. The phantom
- * high comes within 7ms of de-asserting PD and persists for at least
- * 15ms. The real high comes roughly 50ms after PD is de-asserted. The
- * phantom high makes it hard for us to know when the NXP chip is up.
- */
- mdelay(90);
-
- for (num_tries = 0; num_tries < max_tries; num_tries++) {
- /* Check HPD. If it's high, or we don't have it, all is well */
- ret = video_bridge_check_attached(dev);
- if (!ret || ret == -ENOENT)
- return 0;
-
- debug("%s: eDP bridge failed to come up; try %d of %d\n",
- __func__, num_tries, max_tries);
- }
-
- /* Immediately go into bridge reset if the hp line is not high */
- return -EIO;
-}
-
-static int board_dp_bridge_setup(const void *blob)
-{
- const int max_tries = 2;
- int num_tries;
- struct udevice *dev;
- int ret;
-
- /* Configure I2C registers for Parade bridge */
- ret = uclass_get_device(UCLASS_VIDEO_BRIDGE, 0, &dev);
- if (ret) {
- debug("video bridge init failed: %d\n", ret);
- return ret;
- }
-
- if (strncmp(dev->driver->name, "parade", 6)) {
- /* Mux HPHPD to the special hotplug detect mode */
- exynos_pinmux_config(PERIPH_ID_DPHPD, 0);
- }
-
- for (num_tries = 0; num_tries < max_tries; num_tries++) {
- ret = board_dp_bridge_init(dev);
- if (!ret)
- return 0;
- if (num_tries == max_tries - 1)
- break;
-
- /*
- * If we're here, the bridge chip failed to initialise.
- * Power down the bridge in an attempt to reset.
- */
- video_bridge_set_active(dev, false);
-
- /*
- * Arbitrarily wait 300ms here with DP_N low. Don't know for
- * sure how long we should wait, but we're being paranoid.
- */
- mdelay(300);
- }
-
- return ret;
-}
-
-void exynos_cfg_lcd_gpio(void)
-{
- /* For Backlight */
- gpio_request(EXYNOS5_GPIO_B20, "lcd_backlight");
- gpio_cfg_pin(EXYNOS5_GPIO_B20, S5P_GPIO_OUTPUT);
- gpio_set_value(EXYNOS5_GPIO_B20, 1);
-}
-
-static int board_dp_set_backlight(int percent)
-{
- struct udevice *dev;
- int ret;
-
- ret = uclass_get_device(UCLASS_VIDEO_BRIDGE, 0, &dev);
- if (!ret)
- ret = video_bridge_set_backlight(dev, percent);
-
- return ret;
-}
-
-void exynos_backlight_on(unsigned int on)
-{
- struct udevice *dev;
- int ret;
-
- debug("%s(%u)\n", __func__, on);
- if (!on)
- return;
-
- ret = regulator_get_by_platname("vcd_led", &dev);
- if (!ret)
- ret = regulator_set_enable(dev, true);
- if (ret)
- debug("Failed to enable backlight: ret=%d\n", ret);
-
- /* T5 in the LCD timing spec (defined as > 10ms) */
- mdelay(10);
-
- /* board_dp_backlight_pwm */
- gpio_direction_output(EXYNOS5_GPIO_B20, 1);
-
- /* T6 in the LCD timing spec (defined as > 10ms) */
- mdelay(10);
-
- /* try to set the backlight in the bridge registers */
- ret = board_dp_set_backlight(80);
-
- /* if we have no bridge or it does not support backlight, use a GPIO */
- if (ret == -ENODEV || ret == -ENOSYS) {
- gpio_request(EXYNOS5_GPIO_X30, "board_dp_backlight_en");
- gpio_direction_output(EXYNOS5_GPIO_X30, 1);
- }
-}
-
-void exynos_lcd_power_on(void)
-{
- struct udevice *dev;
- int ret;
-
- debug("%s\n", __func__);
- ret = regulator_get_by_platname("lcd_vdd", &dev);
- if (!ret)
- ret = regulator_set_enable(dev, true);
- if (ret)
- debug("Failed to enable LCD panel: ret=%d\n", ret);
-
- ret = board_dp_bridge_setup(gd->fdt_blob);
- if (ret && ret != -ENODEV)
- printf("LCD bridge failed to enable: %d\n", ret);
-}
-
-#endif
-
#ifdef CONFIG_USB_DWC3
static struct dwc3_device dwc3_device_data = {
.maximum_speed = USB_SPEED_SUPER,
diff --git a/drivers/video/exynos/exynos_fb.c b/drivers/video/exynos/exynos_fb.c
index c8fef63..97228cd 100644
--- a/drivers/video/exynos/exynos_fb.c
+++ b/drivers/video/exynos/exynos_fb.c
@@ -479,39 +479,6 @@ unsigned long exynos_fimd_calc_fbsize(struct exynos_fb_priv *priv)
return priv->vl_col * priv->vl_row * (VNBITS(priv->vl_bpix) / 8);
}
-__weak void exynos_cfg_lcd_gpio(void)
-{
-}
-
-__weak void exynos_backlight_on(unsigned int onoff)
-{
-}
-
-__weak void exynos_reset_lcd(void)
-{
-}
-
-__weak void exynos_lcd_power_on(void)
-{
-}
-
-__weak void exynos_cfg_ldo(void)
-{
-}
-
-__weak void exynos_enable_ldo(unsigned int onoff)
-{
-}
-
-__weak void exynos_backlight_reset(void)
-{
-}
-
-__weak int exynos_lcd_misc_init(struct vidinfo *vid)
-{
- return 0;
-}
-
int exynos_fb_ofdata_to_platdata(struct udevice *dev)
{
struct exynos_fb_priv *priv = dev_get_priv(dev);
diff --git a/drivers/video/exynos/exynos_fb.h b/drivers/video/exynos/exynos_fb.h
deleted file mode 100644
index f59cce0..0000000
--- a/drivers/video/exynos/exynos_fb.h
+++ /dev/null
@@ -1,41 +0,0 @@
-/*
- * Copyright (C) 2012 Samsung Electronics
- *
- * Author: InKi Dae <inki.dae at samsung.com>
- * Author: Donghwa Lee <dh09.lee at samsung.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef _EXYNOS_FB_H_
-#define _EXYNOS_FB_H_
-
-#include <asm/arch/fb.h>
-
-#define MAX_CLOCK (86 * 1000000)
-
-enum exynos_cpu_auto_cmd_rate {
- DISABLE_AUTO_FRM,
- PER_TWO_FRM,
- PER_FOUR_FRM,
- PER_SIX_FRM,
- PER_EIGHT_FRM,
- PER_TEN_FRM,
- PER_TWELVE_FRM,
- PER_FOURTEEN_FRM,
- PER_SIXTEEN_FRM,
- PER_EIGHTEEN_FRM,
- PER_TWENTY_FRM,
- PER_TWENTY_TWO_FRM,
- PER_TWENTY_FOUR_FRM,
- PER_TWENTY_SIX_FRM,
- PER_TWENTY_EIGHT_FRM,
- PER_THIRTY_FRM,
-};
-
-void exynos_fimd_lcd_init_mem(unsigned long screen_base, unsigned long fb_size,
- unsigned long palette_size);
-void exynos_fimd_lcd_init(struct vidinfo *vid, ulong lcd_base_address);
-unsigned long exynos_fimd_calc_fbsize(struct vidinfo *pvid);
-
-#endif
--
2.6.0.rc2.230.g3dd15c0
More information about the U-Boot
mailing list