[U-Boot] [REGRESSION] Ethernet broken on Colibri T20/T30

[Stephen Warren]

On 01/16/2016 05:51 PM, Marcel Ziswiler wrote:
> Hi Simon
>
> As mentioned before I noticed Ethernet (on-module USB ASIX chip) to be
> broken on master while it still worked fine in v2016.01. I kind of
> remember having once noticed something along those lines when testing
> some of your early dm stuff but could not find our discussion about it
> anymore plus I don't think it did actually lead anywhere.
>
> FWIW it currently crashes as follows (showing Colibri T20 but the same
> happens on Colibri T30):
>
> U-Boot SPL 2016.01-00205-gb8c5b47 (Jan 17 2016 - 01:31:48)
...
> Colibri T20 # usb start
> starting USB...
> USB0:   USB EHCI 1.00
> USB1:   USB EHCI 1.00
> USB2:   USB EHCI 1.00
> scanning bus 1 for devices... 1 USB Device(s) found
> scanning bus 2 for devices...
> Warning: asix_eth using MAC address from ROM
> 2 USB Device(s) found
> scanning bus 0 for devices... 2 USB Device(s) found
> Colibri T20 # dhcp
> BOOTP broadcast 1
> EHCI timed out on TD - token=0x88008d80
> Rx: failed to receive: -5
> BOOTP broadcast 2
> EHCI timed out on TD - token=0x8008d80
> Rx: failed to receive: -5
> BOOTP broadcast 3
> EHCI timed out on TD - token=0x88008d80
> Rx: failed to receive: -5
> BOOTP broadcast 4
> EHCI timed out on TD - token=0x8008d80
> Rx: failed to receive: -5
> BOOTP broadcast 5
> EHCI timed out on TD - token=0x88008d80
> Rx: failed to receive: -5
> BOOTP broadcast 6
> EHCI timed out on TD - token=0x8008d80
> Rx: failed to receive: -5
>
> Retry time exceeded; starting again
> data abort
> pc : [<1fb4d194>]	   lr : [<1fbb9784>]
> reloc pc : [<0012d194>]	   lr : [<00199784>]
> sp : 1d61c5e0  ip : 6aa665ea	 fp : 1d62bca0
> r10: 00000000  r9 : 1d61fee0	 r8 : 1d62bca0
> r7 : 00000000  r6 : 1d6312e0	 r5 : 1f6da8e0  r4 : 00000000
> r3 : 1c585760  r2 : 03155180	 r1 : 00000000  r0 : caa661ca
> Flags: NzCv  IRQs off  FIQs off  Mode SVC_32
> Resetting CPU ...
>
> resetting ...
>
> Do you have any clue what could be going on?

FWIW, I tried that same commit on Beaver with an asix USB Ethernet 
device and didn't see that problem, even after aligning the config file 
for Beaver more closely with colibri_t30 (e.g. disabling PCIe support, 
copying all the config options that colibri_t30 has but beaver doesn't 
into beaver's config file).

I wonder if it's anything to do with having 3 USB controllers active 
rather than 2 (although that seems unlikely; I can see going from 1->2 
causing issues, but once 2 work, adding more seems like it should). 
Perhaps there's a DRAM bandwidth issue, but then I can't see why the 
patches between v2016.01 and the commit you mentioned would affect that.