[U-Boot] [PATCH v3 1/3] armv8/ls1043aqds: Select lpuart pins of various muxes

Bin Meng bmeng.cn at gmail.com
Thu Jan 21 09:39:45 CET 2016


Hi Wenbin,

On Thu, Jan 21, 2016 at 4:35 PM, Bin Meng <bmeng.cn at gmail.com> wrote:
> Hi Wenbin,
>
> On Thu, Jan 21, 2016 at 2:32 PM, Wenbin Song <wenbin.song at nxp.com> wrote:
>> From: Shaohui Xie <Shaohui.Xie at freescale.com>
>>
>> Set Board Configuration Register to select the lpuart pins of various
>> muxes.
>>
>> Signed-off-by: Shaohui Xie <Shaohui.Xie at freescale.com>
>> Signed-off-by: Mingkai Hu <Mingkai.Hu at freescale.com>
>> ---
>
> Please always include a changelog when you do new version so that
> other people know what's changed.
>
>>  board/freescale/ls1043aqds/ls1043aqds.c | 15 +++++++++++++++
>>  1 file changed, 15 insertions(+)
>>
>> diff --git a/board/freescale/ls1043aqds/ls1043aqds.c b/board/freescale/ls1043aqds/ls1043aqds.c
>> index d6696ca..67f4c4b 100644
>> --- a/board/freescale/ls1043aqds/ls1043aqds.c
>> +++ b/board/freescale/ls1043aqds/ls1043aqds.c
>> @@ -40,6 +40,9 @@ enum {
>>  #define CFG_SD_MUX3_MUX4       0x1 /* MUX4 */
>>  #define CFG_SD_MUX4_SLOT3      0x0 /* SLOT3 TX/RX1 */
>>  #define CFG_SD_MUX4_SLOT1      0x1 /* SLOT1 TX/RX3 */
>> +#define CFG_UART_MUX_MASK      0x6
>> +#define CFG_UART_MUX_SHIFT     1
>> +#define CFG_LPUART_EN          0x1
>>
>>  int checkboard(void)
>>  {
>> @@ -218,7 +221,19 @@ void board_retimer_init(void)
>>
>>  int board_early_init_f(void)
>>  {
>> +#ifdef CONFIG_LPUART
>> +       u8 uart;
>> +#endif
>>         fsl_lsch2_early_init_f();
>> +#ifdef CONFIG_LPUART
>> +
>
> nits: this blank line is not needed
>
>> +        /* We use lpuart1 as system console. */

One more question: in your patch 3, you listed lpuart0 as the /chosen
node, but here the comments says lpuart1. Which one is correct?

>
> nits: ending period is not needed
>
>> +
>> +       uart = QIXIS_READ(brdcfg[14]);
>> +       uart &= ~CFG_UART_MUX_MASK;
>> +       uart |= CFG_LPUART_EN << CFG_UART_MUX_SHIFT;
>> +       QIXIS_WRITE(brdcfg[14], uart);
>> +#endif
>>
>>         return 0;
>>  }
>> --
>
> Other than that,
> Reviewed-by: Bin Meng <bmeng.cn at gmail.com>
>
> Regards,
> Bin


More information about the U-Boot mailing list