[U-Boot] [PATCH 10/11][v5] armv8: ls1012a: Add support of ls1012ardb board

Prabhakar Kushwaha prabhakar.kushwaha at nxp.com
Fri Jun 3 15:11:35 CEST 2016


QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.

Signed-off-by: Calvin Johnson <calvin.johnson at nxp.com>
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava at nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha at nxp.com>
---
Changes for v2: Sending as it is
Changes for v3: Incorporated York's comments
Changes for v4: Incorporated Alex and York's comments
	- removed ddr init magic numbers
	- updated file license
	- define pcie, sata, sdhc define in rdb.h
	- use arch_fixup_fdt
Changes for v5: Use macro for DDR init

 arch/arm/Kconfig                        |  10 ++
 arch/arm/dts/Makefile                   |   3 +-
 arch/arm/dts/fsl-ls1012a-rdb.dts        |  16 +++
 arch/arm/dts/fsl-ls1012a-rdb.dtsi       |  39 ++++++
 board/freescale/ls1012ardb/Kconfig      |  15 +++
 board/freescale/ls1012ardb/MAINTAINERS  |   6 +
 board/freescale/ls1012ardb/Makefile     |   7 +
 board/freescale/ls1012ardb/README       |  54 ++++++++
 board/freescale/ls1012ardb/ls1012ardb.c | 224 ++++++++++++++++++++++++++++++++
 configs/ls1012ardb_qspi_defconfig       |  32 +++++
 include/configs/ls1012ardb.h            | 107 +++++++++++++++
 11 files changed, 512 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/dts/fsl-ls1012a-rdb.dts
 create mode 100644 arch/arm/dts/fsl-ls1012a-rdb.dtsi
 create mode 100644 board/freescale/ls1012ardb/Kconfig
 create mode 100644 board/freescale/ls1012ardb/MAINTAINERS
 create mode 100644 board/freescale/ls1012ardb/Makefile
 create mode 100644 board/freescale/ls1012ardb/README
 create mode 100644 board/freescale/ls1012ardb/ls1012ardb.c
 create mode 100644 configs/ls1012ardb_qspi_defconfig
 create mode 100644 include/configs/ls1012ardb.h

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 30fc32a..9be8c2b 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -705,6 +705,15 @@ config TARGET_LS1012AQDS
 	  development platform that supports the QorIQ LS1012A
 	  Layerscape Architecture processor.
 
+config TARGET_LS1012ARDB
+	bool "Support ls1012ardb"
+	select ARM64
+	help
+	  Support for Freescale LS1012ARDB platform.
+	  The LS1012A Reference design board (RDB) is a high-performance
+	  development platform that supports the QorIQ LS1012A
+	  Layerscape Architecture processor.
+
 config TARGET_LS1021AQDS
 	bool "Support ls1021aqds"
 	select CPU_V7
@@ -862,6 +871,7 @@ source "board/freescale/ls1043aqds/Kconfig"
 source "board/freescale/ls1021atwr/Kconfig"
 source "board/freescale/ls1043ardb/Kconfig"
 source "board/freescale/ls1012aqds/Kconfig"
+source "board/freescale/ls1012ardb/Kconfig"
 source "board/freescale/mx23evk/Kconfig"
 source "board/freescale/mx25pdk/Kconfig"
 source "board/freescale/mx28evk/Kconfig"
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 47ec7a2..f021699 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -121,7 +121,8 @@ dtb-$(CONFIG_FSL_LSCH3) += fsl-ls2080a-qds.dtb \
 dtb-$(CONFIG_FSL_LSCH2) += fsl-ls1043a-qds-duart.dtb \
 	fsl-ls1043a-qds-lpuart.dtb \
 	fsl-ls1043a-rdb.dtb \
-	fsl-ls1012a-qds.dtb
+	fsl-ls1012a-qds.dtb \
+	fsl-ls1012a-rdb.dtb
 
 dtb-$(CONFIG_ARCH_SNAPDRAGON) += dragonboard410c.dtb
 
diff --git a/arch/arm/dts/fsl-ls1012a-rdb.dts b/arch/arm/dts/fsl-ls1012a-rdb.dts
new file mode 100644
index 0000000..f683812
--- /dev/null
+++ b/arch/arm/dts/fsl-ls1012a-rdb.dts
@@ -0,0 +1,16 @@
+/*
+ * Device Tree file for Freescale Layerscape-1012A family SoC.
+ *
+ * Copyright 2016, Freescale Semiconductor
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+/dts-v1/;
+#include "fsl-ls1012a-rdb.dtsi"
+
+/ {
+       chosen {
+               stdout-path = &duart0;
+       };
+};
diff --git a/arch/arm/dts/fsl-ls1012a-rdb.dtsi b/arch/arm/dts/fsl-ls1012a-rdb.dtsi
new file mode 100644
index 0000000..bf407ae
--- /dev/null
+++ b/arch/arm/dts/fsl-ls1012a-rdb.dtsi
@@ -0,0 +1,39 @@
+/*
+ * Device Tree Include file for Freescale Layerscape-1012A family SoC.
+ *
+ * Copyright 2016, Freescale Semiconductor
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/include/ "fsl-ls1012a.dtsi"
+
+/ {
+	model = "LS1012A RDB Board";
+	aliases {
+		spi0 = &qspi;
+	};
+};
+
+&qspi {
+	bus-num = <0>;
+	status = "okay";
+
+	qflash0: s25fl128s at 0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "spi-flash";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&duart0 {
+	status = "okay";
+};
diff --git a/board/freescale/ls1012ardb/Kconfig b/board/freescale/ls1012ardb/Kconfig
new file mode 100644
index 0000000..3f67c28
--- /dev/null
+++ b/board/freescale/ls1012ardb/Kconfig
@@ -0,0 +1,15 @@
+if TARGET_LS1012ARDB
+
+config SYS_BOARD
+	default "ls1012ardb"
+
+config SYS_VENDOR
+	default "freescale"
+
+config SYS_SOC
+	default "fsl-layerscape"
+
+config SYS_CONFIG_NAME
+	default "ls1012ardb"
+
+endif
diff --git a/board/freescale/ls1012ardb/MAINTAINERS b/board/freescale/ls1012ardb/MAINTAINERS
new file mode 100644
index 0000000..79a2a7d
--- /dev/null
+++ b/board/freescale/ls1012ardb/MAINTAINERS
@@ -0,0 +1,6 @@
+LS1012ARDB BOARD
+M:	Prabhakar Kushwaha <prabhakar.kushwaha at nxp.com>
+S:	Maintained
+F:	board/freescale/ls1012ardb/
+F:	include/configs/ls1012ardb.h
+F:	configs/ls1012ardb_qspi_defconfig
diff --git a/board/freescale/ls1012ardb/Makefile b/board/freescale/ls1012ardb/Makefile
new file mode 100644
index 0000000..05fa9d9
--- /dev/null
+++ b/board/freescale/ls1012ardb/Makefile
@@ -0,0 +1,7 @@
+#
+# Copyright 2016 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier:      GPL-2.0+
+#
+
+obj-y += ls1012ardb.o
diff --git a/board/freescale/ls1012ardb/README b/board/freescale/ls1012ardb/README
new file mode 100644
index 0000000..453b432
--- /dev/null
+++ b/board/freescale/ls1012ardb/README
@@ -0,0 +1,54 @@
+Overview
+--------
+QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
+development platform, with a complete debugging environment.
+The LS1012ARDB board supports the QorIQ LS1012A processor and is
+optimized to support the high-bandwidth DDR3L memory and
+a full complement of high-speed SerDes ports.
+
+LS1012A SoC Overview
+--------------------
+Please refer arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc for LS2080A
+SoC overview.
+
+LS1012ARDB board Overview
+-----------------------
+ - SERDES Connections, 4 lanes supporting:
+      - PCI Express - 3.0
+      - SGMII, SGMII 2.5
+      - SATA 3.0
+ - DDR Controller
+     - 16-bit, 1 GB DDR3L SDRAM memory, running at data rates up to 1 GT/s
+ -QSPI: A dual 1:3 switch, NX3L4357GM,115 (U35) drives the QSPI chip-select
+ signals to
+    - QSPI NOR flash memory (2 virtual banks)
+    - the QSPI emulator.s
+ - USB 3.0
+    - one high-speed USB 2.0/3.0 port.
+ - Two enhanced secure digital host controllers:
+    - SDHC1 controller can be connected to onboard SDHC connector
+    - SDHC2 controller: Three dual 1:4 mux/demux devices,
+    74CBTLV3253DS (U30, U31, U33) drive the SDHC2 signals to eMMC,
+    SDIO WiFi, SPI, and Ardiuno shield
+ - 2 I2C controllers
+ - One SATA onboard connectors
+ - UART
+   - The LS1012A processor consists of two UART controllers,
+   out of which only UART1 is used on RDB.
+ - ARM JTAG support
+
+Booting Options
+---------------
+a) QSPI Flash Emu Boot
+b) QSPI Flash 1
+c) QSPI Flash 2
+
+QSPI flash map
+--------------
+Images		| Size	|QSPI Flash Address
+------------------------------------------
+RCW + PBI	| 1MB	| 0x4000_0000
+U-boot 		| 1MB	| 0x4010_0000
+U-boot Env 	| 1MB	| 0x4020_0000
+PPA FIT image	| 2MB	| 0x4050_0000
+Linux ITB	| ~53MB | 0x40A0_0000
diff --git a/board/freescale/ls1012ardb/ls1012ardb.c b/board/freescale/ls1012ardb/ls1012ardb.c
new file mode 100644
index 0000000..f69768d
--- /dev/null
+++ b/board/freescale/ls1012ardb/ls1012ardb.c
@@ -0,0 +1,224 @@
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <asm/io.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/fsl_serdes.h>
+#include <asm/arch/soc.h>
+#include <hwconfig.h>
+#include <ahci.h>
+#include <mmc.h>
+#include <scsi.h>
+#include <fsl_csu.h>
+#include <fsl_esdhc.h>
+#include <environment.h>
+#include <fsl_mmdc.h>
+#include <netdev.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static void set_wait_for_bits_clear(void *ptr, u32 value, u32 bits)
+{
+	int timeout = 1000;
+
+	out_be32(ptr, value);
+
+	while (in_be32(ptr) & bits) {
+		udelay(100);
+		timeout--;
+	}
+	if (timeout <= 0)
+		puts("Error: wait for clear timeout.\n");
+}
+
+int checkboard(void)
+{
+	u8 in1;
+
+	puts("Board: LS1012ARDB ");
+
+	/* Initialize i2c early for Serial flash bank information */
+	i2c_set_bus_num(0);
+
+	if (i2c_read(I2C_MUX_IO1_ADDR, 1, 1, &in1, 1) < 0) {
+		printf("Error reading i2c boot information!\n");
+		return 0; /* Don't want to hang() on this error */
+	}
+
+	puts("Version");
+	if ((in1 & (~__SW_REV_MASK)) == __SW_REV_A)
+		puts(": RevA");
+	else if ((in1 & (~__SW_REV_MASK)) == __SW_REV_B)
+		puts(": RevB");
+	else
+		puts(": unknown");
+
+	printf(", boot from QSPI");
+	if ((in1 & (~__SW_BOOT_MASK)) == __SW_BOOT_EMU)
+		puts(": emu\n");
+	else if ((in1 & (~__SW_BOOT_MASK)) == __SW_BOOT_BANK1)
+		puts(": bank1\n");
+	else if ((in1 & (~__SW_BOOT_MASK)) == __SW_BOOT_BANK2)
+		puts(": bank2\n");
+	else
+		puts("unknown\n");
+
+	return 0;
+}
+
+void mmdc_init(void)
+{
+	struct mmdc_p_regs *mmdc =
+		(struct mmdc_p_regs *)CONFIG_SYS_FSL_DDR_ADDR;
+
+	out_be32(&mmdc->mdscr, CONFIGURATION_REQ);
+
+	/* configure timing parms */
+	out_be32(&mmdc->mdotc,  CONFIG_SYS_MMDC_CORE_ODT_TIMING);
+	out_be32(&mmdc->mdcfg0, CONFIG_SYS_MMDC_CORE_TIMING_CFG_0);
+	out_be32(&mmdc->mdcfg1, CONFIG_SYS_MMDC_CORE_TIMING_CFG_1);
+	out_be32(&mmdc->mdcfg2, CONFIG_SYS_MMDC_CORE_TIMING_CFG_2);
+
+	/* other parms	*/
+	out_be32(&mmdc->mdmisc,    CONFIG_SYS_MMDC_CORE_MISC);
+	out_be32(&mmdc->mpmur0,    CONFIG_SYS_MMDC_PHY_MEASURE_UNIT);
+	out_be32(&mmdc->mdrwd,     CONFIG_SYS_MMDC_CORE_RDWR_CMD_DELAY);
+	out_be32(&mmdc->mpodtctrl, CONFIG_SYS_MMDC_PHY_ODT_CTRL);
+
+	/* out of reset delays */
+	out_be32(&mmdc->mdor,  CONFIG_SYS_MMDC_CORE_OUT_OF_RESET_DELAY);
+
+	/* physical parms */
+	out_be32(&mmdc->mdctl, CONFIG_SYS_MMDC_CORE_CONTROL_1);
+	out_be32(&mmdc->mdasp, CONFIG_SYS_MMDC_CORE_ADDR_PARTITION);
+
+       /* Enable MMDC */
+	out_be32(&mmdc->mdctl, CONFIG_SYS_MMDC_CORE_CONTROL_2);
+
+	/* dram init sequence: update MRs */
+	out_be32(&mmdc->mdscr, (CMD_ADDR_LSB_MR_ADDR(0x8) | CONFIGURATION_REQ |
+				CMD_LOAD_MODE_REG | CMD_BANK_ADDR_2));
+	out_be32(&mmdc->mdscr, (CONFIGURATION_REQ | CMD_LOAD_MODE_REG |
+				CMD_BANK_ADDR_3));
+	out_be32(&mmdc->mdscr, (CMD_ADDR_LSB_MR_ADDR(0x4) | CONFIGURATION_REQ |
+				CMD_LOAD_MODE_REG | CMD_BANK_ADDR_1));
+	out_be32(&mmdc->mdscr, (CMD_ADDR_MSB_MR_OP(0x19) |
+				CMD_ADDR_LSB_MR_ADDR(0x30) | CONFIGURATION_REQ |
+				CMD_LOAD_MODE_REG | CMD_BANK_ADDR_0));
+
+       /* dram init sequence: ZQCL */
+	out_be32(&mmdc->mdscr, (CMD_ADDR_MSB_MR_OP(0x4) | CONFIGURATION_REQ |
+				CMD_ZQ_CALIBRATION | CMD_BANK_ADDR_0));
+	set_wait_for_bits_clear(&mmdc->mpzqhwctrl,
+				CONFIG_SYS_MMDC_PHY_ZQ_HW_CTRL,
+				FORCE_ZQ_AUTO_CALIBRATION);
+
+       /* Calibrations now: wr lvl */
+	out_be32(&mmdc->mdscr, (CMD_ADDR_LSB_MR_ADDR(0x84) |
+				CONFIGURATION_REQ | CMD_LOAD_MODE_REG |
+				CMD_BANK_ADDR_1));
+	out_be32(&mmdc->mdscr, (CONFIGURATION_REQ | WL_EN | CMD_NORMAL));
+	set_wait_for_bits_clear(&mmdc->mpwlgcr, WR_LVL_HW_EN, WR_LVL_HW_EN);
+
+	mdelay(1);
+
+	out_be32(&mmdc->mdscr, (CMD_ADDR_LSB_MR_ADDR(0x4) | CONFIGURATION_REQ |
+				CMD_LOAD_MODE_REG | CMD_BANK_ADDR_1));
+	out_be32(&mmdc->mdscr, CONFIGURATION_REQ);
+
+	mdelay(1);
+
+       /* Calibrations now: Read DQS gating calibration */
+	out_be32(&mmdc->mdscr, (CMD_ADDR_MSB_MR_OP(0x4) | CONFIGURATION_REQ |
+				CMD_PRECHARGE_BANK_OPEN | CMD_BANK_ADDR_0));
+	out_be32(&mmdc->mdscr, (CMD_ADDR_LSB_MR_ADDR(0x4) | CONFIGURATION_REQ |
+				CMD_LOAD_MODE_REG | CMD_BANK_ADDR_3));
+	out_be32(&mmdc->mppdcmpr2, MPR_COMPARE_EN);
+	out_be32(&mmdc->mprddlctl, CONFIG_SYS_MMDC_PHY_RD_DLY_LINES_CFG);
+	set_wait_for_bits_clear(&mmdc->mpdgctrl0,
+				AUTO_RD_DQS_GATING_CALIBRATION_EN,
+				AUTO_RD_DQS_GATING_CALIBRATION_EN);
+
+	out_be32(&mmdc->mdscr, (CONFIGURATION_REQ | CMD_LOAD_MODE_REG |
+				CMD_BANK_ADDR_3));
+
+       /* Calibrations now: Read calibration */
+	out_be32(&mmdc->mdscr, (CMD_ADDR_MSB_MR_OP(0x4) | CONFIGURATION_REQ |
+				CMD_PRECHARGE_BANK_OPEN | CMD_BANK_ADDR_0));
+	out_be32(&mmdc->mdscr, (CMD_ADDR_LSB_MR_ADDR(0x4) | CONFIGURATION_REQ |
+				CMD_LOAD_MODE_REG | CMD_BANK_ADDR_3));
+	out_be32(&mmdc->mppdcmpr2,  MPR_COMPARE_EN);
+	set_wait_for_bits_clear(&mmdc->mprddlhwctl,
+				AUTO_RD_CALIBRATION_EN,
+				AUTO_RD_CALIBRATION_EN);
+
+	out_be32(&mmdc->mdscr, (CONFIGURATION_REQ | CMD_LOAD_MODE_REG |
+				CMD_BANK_ADDR_3));
+
+       /* PD, SR */
+	out_be32(&mmdc->mdpdc, CONFIG_SYS_MMDC_CORE_PWR_DOWN_CTRL);
+	out_be32(&mmdc->mapsr, CONFIG_SYS_MMDC_CORE_PWR_SAV_CTRL_STAT);
+
+       /* refresh scheme */
+	set_wait_for_bits_clear(&mmdc->mdref,
+				CONFIG_SYS_MMDC_CORE_REFRESH_CTL,
+				START_REFRESH);
+
+       /* disable CON_REQ */
+	out_be32(&mmdc->mdscr, DISABLE_CFG_REQ);
+}
+
+int dram_init(void)
+{
+	mmdc_init();
+
+	gd->ram_size = CONFIG_SYS_SDRAM_SIZE;
+
+	return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+	return pci_eth_init(bis);
+}
+
+int board_early_init_f(void)
+{
+	fsl_lsch2_early_init_f();
+
+	return 0;
+}
+
+int board_init(void)
+{
+	struct ccsr_cci400 *cci = (struct ccsr_cci400 *)CONFIG_SYS_CCI400_ADDR;
+	/*
+	 * Set CCI-400 control override register to enable barrier
+	 * transaction
+	 */
+	out_le32(&cci->ctrl_ord, CCI400_CTRLORD_EN_BARRIER);
+
+#ifdef CONFIG_ENV_IS_NOWHERE
+	gd->env_addr = (ulong)&default_environment[0];
+#endif
+
+#ifdef CONFIG_LAYERSCAPE_NS_ACCESS
+	enable_layerscape_ns_access();
+#endif
+
+	return 0;
+}
+
+int ft_board_setup(void *blob, bd_t *bd)
+{
+	arch_fixup_fdt(blob);
+
+	ft_cpu_setup(blob, bd);
+
+	return 0;
+}
diff --git a/configs/ls1012ardb_qspi_defconfig b/configs/ls1012ardb_qspi_defconfig
new file mode 100644
index 0000000..456eebd
--- /dev/null
+++ b/configs/ls1012ardb_qspi_defconfig
@@ -0,0 +1,32 @@
+CONFIG_ARM=y
+CONFIG_TARGET_LS1012ARDB=y
+# CONFIG_SYS_MALLOC_F is not set
+CONFIG_SPI_FLASH=y
+CONFIG_DM_SPI=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1012a-rdb"
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_OF_STDOUT_VIA_ALIAS=y
+CONFIG_SYS_EXTRA_OPTIONS="QSPI_BOOT"
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_GREPENV=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_DM=y
+CONFIG_NETDEVICES=y
+CONFIG_E1000=y
+CONFIG_SYS_NS16550=y
+CONFIG_FSL_DSPI=y
diff --git a/include/configs/ls1012ardb.h b/include/configs/ls1012ardb.h
new file mode 100644
index 0000000..f63c66a
--- /dev/null
+++ b/include/configs/ls1012ardb.h
@@ -0,0 +1,107 @@
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __LS1012ARDB_H__
+#define __LS1012ARDB_H__
+
+#include "ls1012a_common.h"
+
+
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	1
+#define CONFIG_NR_DRAM_BANKS		2
+#define CONFIG_SYS_SDRAM_SIZE		0x40000000
+
+#define CONFIG_SYS_MMDC_CORE_CONTROL_1		0x05180000
+#define CONFIG_SYS_MMDC_CORE_CONTROL_2		0x85180000
+
+#define CONFIG_CMD_MEMINFO
+#define CONFIG_CMD_MEMTEST
+#define CONFIG_SYS_MEMTEST_START	0x80000000
+#define CONFIG_SYS_MEMTEST_END		0x9fffffff
+
+/*
+* USB
+*/
+#define CONFIG_HAS_FSL_XHCI_USB
+
+#ifdef CONFIG_HAS_FSL_XHCI_USB
+#define CONFIG_USB_XHCI
+#define CONFIG_USB_XHCI_FSL
+#define CONFIG_USB_XHCI_DWC3
+#define CONFIG_USB_MAX_CONTROLLER_COUNT         1
+#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS      2
+#define CONFIG_USB_STORAGE
+#endif
+
+/*
+ * I2C IO expander
+ */
+
+#define I2C_MUX_IO1_ADDR	0x24
+#define __SW_BOOT_MASK		0xFC
+#define __SW_BOOT_EMU		0x10
+#define __SW_BOOT_BANK1		0x00
+#define __SW_BOOT_BANK2		0x01
+#define __SW_REV_MASK		0x07
+#define __SW_REV_A		0xF8
+#define __SW_REV_B		0xF0
+
+/*  MMC  */
+#define CONFIG_MMC
+#ifdef CONFIG_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
+#define CONFIG_GENERIC_MMC
+#define CONFIG_DOS_PARTITION
+#endif
+
+/* SATA */
+#define CONFIG_LIBATA
+#define	CONFIG_SCSI
+#define CONFIG_SCSI_AHCI
+#define CONFIG_SCSI_AHCI_PLAT
+#define CONFIG_CMD_SCSI
+#define CONFIG_DOS_PARTITION
+#define CONFIG_BOARD_LATE_INIT
+
+#define CONFIG_SYS_SATA				AHCI_BASE_ADDR
+
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID		1
+#define CONFIG_SYS_SCSI_MAX_LUN			1
+#define CONFIG_SYS_SCSI_MAX_DEVICE		(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
+						CONFIG_SYS_SCSI_MAX_LUN)
+#define CONFIG_PCI		/* Enable PCI/PCIE */
+#define CONFIG_PCIE1		/* PCIE controller 1 */
+#define CONFIG_PCIE_LAYERSCAPE	/* Use common FSL Layerscape PCIe code */
+#define FSL_PCIE_COMPAT "fsl,ls1043a-pcie"
+
+#define CONFIG_SYS_PCI_64BIT
+
+#define CONFIG_SYS_PCIE_CFG0_PHYS_OFF	0x00000000
+#define CONFIG_SYS_PCIE_CFG0_SIZE	0x00001000	/* 4k */
+#define CONFIG_SYS_PCIE_CFG1_PHYS_OFF	0x00001000
+#define CONFIG_SYS_PCIE_CFG1_SIZE	0x00001000	/* 4k */
+
+#define CONFIG_SYS_PCIE_IO_BUS		0x00000000
+#define CONFIG_SYS_PCIE_IO_PHYS_OFF	0x00010000
+#define CONFIG_SYS_PCIE_IO_SIZE		0x00010000	/* 64k */
+
+#define CONFIG_SYS_PCIE_MEM_BUS         0x08000000
+#define CONFIG_SYS_PCIE_MEM_PHYS_OFF    0x04000000
+#define CONFIG_SYS_PCIE_MEM_SIZE        0x80000000      /* 128M */
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP
+#define CONFIG_PCI_SCAN_SHOW
+#define CONFIG_CMD_PCI
+
+#define CONFIG_CMD_MEMINFO
+#define CONFIG_CMD_MEMTEST
+#define CONFIG_SYS_MEMTEST_START	0x80000000
+#define CONFIG_SYS_MEMTEST_END		0x9fffffff
+
+#endif /* __LS1012ARDB_H__ */
-- 
1.9.1




More information about the U-Boot mailing list