[U-Boot] [PATCH] spi: pic32_spi: add SPI master driver for PIC32 SoC.

Daniel Schwierzeck daniel.schwierzeck at gmail.com
Fri Jun 3 16:21:55 CEST 2016



Am 02.06.2016 um 10:56 schrieb Purna Chandra Mandal:
> This driver implements SPI protocol in master mode to communicate
> with the SPI device connected on SPI bus. It handles /CS explicitly
> by controlling respective pin as gpio ('cs-gpios' property in dt node)
> and uses PIO mode for SPI transaction. It is configurable based
> on driver-model only.
> 
> Cc: Jagan Teki <jteki at openedev.com>
> Signed-off-by: Purna Chandra Mandal <purna.mandal at microchip.com>
> 

Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck at gmail.com>

> ---
> 
>  drivers/spi/Kconfig     |   8 +
>  drivers/spi/Makefile    |   1 +
>  drivers/spi/pic32_spi.c | 448 ++++++++++++++++++++++++++++++++++++++++++++++++
>  3 files changed, 457 insertions(+)
>  create mode 100644 drivers/spi/pic32_spi.c
> 
> diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
> index b7fd8e5..aca385d 100644
> --- a/drivers/spi/Kconfig
> +++ b/drivers/spi/Kconfig
> @@ -75,6 +75,14 @@ config ICH_SPI
>  	  access the SPI NOR flash on platforms embedding this Intel
>  	  ICH IP core.
>  
> +config PIC32_SPI
> +	bool "Microchip PIC32 SPI driver"
> +	depends on MACH_PIC32
> +	help
> +	  Enable the Microchip PIC32 SPI driver. This driver can be used
> +	  to access the SPI NOR flash, MMC-over-SPI on platforms based on
> +	  Microchip PIC32 family devices.
> +
>  config ROCKCHIP_SPI
>  	bool "Rockchip SPI driver"
>  	help
> diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
> index 7fb2926..b1d9e20 100644
> --- a/drivers/spi/Makefile
> +++ b/drivers/spi/Makefile
> @@ -40,6 +40,7 @@ obj-$(CONFIG_MPC8XXX_SPI) += mpc8xxx_spi.o
>  obj-$(CONFIG_MXC_SPI) += mxc_spi.o
>  obj-$(CONFIG_MXS_SPI) += mxs_spi.o
>  obj-$(CONFIG_OMAP3_SPI) += omap3_spi.o
> +obj-$(CONFIG_PIC32_SPI) += pic32_spi.o
>  obj-$(CONFIG_ROCKCHIP_SPI) += rk_spi.o
>  obj-$(CONFIG_SANDBOX_SPI) += sandbox_spi.o
>  obj-$(CONFIG_SH_SPI) += sh_spi.o
> diff --git a/drivers/spi/pic32_spi.c b/drivers/spi/pic32_spi.c
> new file mode 100644
> index 0000000..25ca1f3
> --- /dev/null
> +++ b/drivers/spi/pic32_spi.c
> @@ -0,0 +1,448 @@
> +/*
> + * Microchip PIC32 SPI controller driver.
> + *
> + * Copyright (c) 2015, Microchip Technology Inc.
> + *      Purna Chandra Mandal <purna.mandal at microchip.com>
> + *
> + * SPDX-License-Identifier:	GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <clk.h>
> +#include <dm.h>
> +#include <linux/compat.h>
> +#include <malloc.h>
> +#include <spi.h>
> +
> +#include <asm/types.h>
> +#include <asm/io.h>
> +#include <asm/gpio.h>
> +#include <dt-bindings/clock/microchip,clock.h>
> +#include <mach/pic32.h>
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +/* PIC32 SPI controller registers */
> +struct pic32_reg_spi {
> +	struct pic32_reg_atomic ctrl;
> +	struct pic32_reg_atomic status;
> +	struct pic32_reg_atomic buf;
> +	struct pic32_reg_atomic baud;
> +	struct pic32_reg_atomic ctrl2;
> +};
> +
> +/* Bit fields in SPI Control Register */
> +#define PIC32_SPI_CTRL_MSTEN	BIT(5) /* Enable SPI Master */
> +#define PIC32_SPI_CTRL_CKP	BIT(6) /* active low */
> +#define PIC32_SPI_CTRL_CKE	BIT(8) /* Tx on falling edge */
> +#define PIC32_SPI_CTRL_SMP	BIT(9) /* Rx at middle or end of tx */
> +#define PIC32_SPI_CTRL_BPW_MASK	0x03   /* Bits per word */
> +#define  PIC32_SPI_CTRL_BPW_8		0x0
> +#define  PIC32_SPI_CTRL_BPW_16		0x1
> +#define  PIC32_SPI_CTRL_BPW_32		0x2
> +#define PIC32_SPI_CTRL_BPW_SHIFT	10
> +#define PIC32_SPI_CTRL_ON	BIT(15) /* Macro enable */
> +#define PIC32_SPI_CTRL_ENHBUF	BIT(16) /* Enable enhanced buffering */
> +#define PIC32_SPI_CTRL_MCLKSEL	BIT(23) /* Select SPI Clock src */
> +#define PIC32_SPI_CTRL_MSSEN	BIT(28) /* SPI macro will drive SS */
> +#define PIC32_SPI_CTRL_FRMEN	BIT(31) /* Enable framing mode */
> +
> +/* Bit fields in SPI Status Register */
> +#define PIC32_SPI_STAT_RX_OV		BIT(6) /* err, s/w needs to clear */
> +#define PIC32_SPI_STAT_TF_LVL_MASK	0x1f
> +#define PIC32_SPI_STAT_TF_LVL_SHIFT	16
> +#define PIC32_SPI_STAT_RF_LVL_MASK	0x1f
> +#define PIC32_SPI_STAT_RF_LVL_SHIFT	24
> +
> +/* Bit fields in SPI Baud Register */
> +#define PIC32_SPI_BAUD_MASK	0x1ff
> +
> +struct pic32_spi_priv {
> +	struct pic32_reg_spi	*regs;
> +	u32			fifo_depth; /* FIFO depth in bytes */
> +	u32			fifo_n_word; /* FIFO depth in words */
> +	struct gpio_desc	cs_gpio;
> +
> +	/* Current SPI slave specific */
> +	ulong			clk_rate;
> +	u32			speed_hz; /* spi-clk rate */
> +	int			mode;
> +
> +	/* Current message/transfer state */
> +	const void		*tx;
> +	const void		*tx_end;
> +	const void		*rx;
> +	const void		*rx_end;
> +	u32			len;
> +
> +	/* SPI FiFo accessor */
> +	void (*rx_fifo)(struct pic32_spi_priv *);
> +	void (*tx_fifo)(struct pic32_spi_priv *);
> +};
> +
> +static inline void pic32_spi_enable(struct pic32_spi_priv *priv)
> +{
> +	writel(PIC32_SPI_CTRL_ON, &priv->regs->ctrl.set);
> +}
> +
> +static inline void pic32_spi_disable(struct pic32_spi_priv *priv)
> +{
> +	writel(PIC32_SPI_CTRL_ON, &priv->regs->ctrl.clr);
> +}
> +
> +static inline u32 pic32_spi_rx_fifo_level(struct pic32_spi_priv *priv)
> +{
> +	u32 sr = readl(&priv->regs->status.raw);
> +
> +	return (sr >> PIC32_SPI_STAT_RF_LVL_SHIFT) & PIC32_SPI_STAT_RF_LVL_MASK;
> +}
> +
> +static inline u32 pic32_spi_tx_fifo_level(struct pic32_spi_priv *priv)
> +{
> +	u32 sr = readl(&priv->regs->status.raw);
> +
> +	return (sr >> PIC32_SPI_STAT_TF_LVL_SHIFT) & PIC32_SPI_STAT_TF_LVL_MASK;
> +}
> +
> +/* Return the max entries we can fill into tx fifo */
> +static u32 pic32_tx_max(struct pic32_spi_priv *priv, int n_bytes)
> +{
> +	u32 tx_left, tx_room, rxtx_gap;
> +
> +	tx_left = (priv->tx_end - priv->tx) / n_bytes;
> +	tx_room = priv->fifo_n_word - pic32_spi_tx_fifo_level(priv);
> +
> +	rxtx_gap = (priv->rx_end - priv->rx) - (priv->tx_end - priv->tx);
> +	rxtx_gap /= n_bytes;
> +	return min3(tx_left, tx_room, (u32)(priv->fifo_n_word - rxtx_gap));
> +}
> +
> +/* Return the max entries we should read out of rx fifo */
> +static u32 pic32_rx_max(struct pic32_spi_priv *priv, int n_bytes)
> +{
> +	u32 rx_left = (priv->rx_end - priv->rx) / n_bytes;
> +
> +	return min_t(u32, rx_left, pic32_spi_rx_fifo_level(priv));
> +}
> +
> +#define BUILD_SPI_FIFO_RW(__name, __type, __bwl)		\
> +static void pic32_spi_rx_##__name(struct pic32_spi_priv *priv)	\
> +{								\
> +	__type val;						\
> +	u32 mx = pic32_rx_max(priv, sizeof(__type));		\
> +								\
> +	for (; mx; mx--) {					\
> +		val = read##__bwl(&priv->regs->buf.raw);	\
> +		if (priv->rx_end - priv->len)			\
> +			*(__type *)(priv->rx) = val;		\
> +		priv->rx += sizeof(__type);			\
> +	}							\
> +}								\
> +								\
> +static void pic32_spi_tx_##__name(struct pic32_spi_priv *priv)	\
> +{								\
> +	__type val;						\
> +	u32 mx = pic32_tx_max(priv, sizeof(__type));		\
> +								\
> +	for (; mx ; mx--) {					\
> +		val = (__type) ~0U;				\
> +		if (priv->tx_end - priv->len)			\
> +			val =  *(__type *)(priv->tx);		\
> +		write##__bwl(val, &priv->regs->buf.raw);	\
> +		priv->tx += sizeof(__type);			\
> +	}							\
> +}
> +BUILD_SPI_FIFO_RW(byte, u8, b);
> +BUILD_SPI_FIFO_RW(word, u16, w);
> +BUILD_SPI_FIFO_RW(dword, u32, l);
> +
> +static int pic32_spi_set_word_size(struct pic32_spi_priv *priv,
> +				   unsigned int wordlen)
> +{
> +	u32 bits_per_word;
> +	u32 val;
> +
> +	switch (wordlen) {
> +	case 8:
> +		priv->rx_fifo = pic32_spi_rx_byte;
> +		priv->tx_fifo = pic32_spi_tx_byte;
> +		bits_per_word = PIC32_SPI_CTRL_BPW_8;
> +		break;
> +	case 16:
> +		priv->rx_fifo = pic32_spi_rx_word;
> +		priv->tx_fifo = pic32_spi_tx_word;
> +		bits_per_word = PIC32_SPI_CTRL_BPW_16;
> +		break;
> +	case 32:
> +		priv->rx_fifo = pic32_spi_rx_dword;
> +		priv->tx_fifo = pic32_spi_tx_dword;
> +		bits_per_word = PIC32_SPI_CTRL_BPW_32;
> +		break;
> +	default:
> +		printf("pic32-spi: unsupported wordlen\n");
> +		return -EINVAL;
> +	}
> +
> +	/* set bits-per-word */
> +	val = readl(&priv->regs->ctrl.raw);
> +	val &= ~(PIC32_SPI_CTRL_BPW_MASK << PIC32_SPI_CTRL_BPW_SHIFT);
> +	val |= bits_per_word << PIC32_SPI_CTRL_BPW_SHIFT;
> +	writel(val, &priv->regs->ctrl.raw);
> +
> +	/* calculate maximum number of words fifo can hold */
> +	priv->fifo_n_word = DIV_ROUND_UP(priv->fifo_depth, wordlen / 8);
> +
> +	return 0;
> +}
> +
> +static int pic32_spi_claim_bus(struct udevice *slave)
> +{
> +	struct pic32_spi_priv *priv = dev_get_priv(slave->parent);
> +
> +	/* enable chip */
> +	pic32_spi_enable(priv);
> +
> +	return 0;
> +}
> +
> +static int pic32_spi_release_bus(struct udevice *slave)
> +{
> +	struct pic32_spi_priv *priv = dev_get_priv(slave->parent);
> +
> +	/* disable chip */
> +	pic32_spi_disable(priv);
> +
> +	return 0;
> +}
> +
> +static void spi_cs_activate(struct pic32_spi_priv *priv)
> +{
> +	if (!dm_gpio_is_valid(&priv->cs_gpio))
> +		return;
> +
> +	dm_gpio_set_value(&priv->cs_gpio, 1);
> +}
> +
> +static void spi_cs_deactivate(struct pic32_spi_priv *priv)
> +{
> +	if (!dm_gpio_is_valid(&priv->cs_gpio))
> +		return;
> +
> +	dm_gpio_set_value(&priv->cs_gpio, 0);
> +}
> +
> +static int pic32_spi_xfer(struct udevice *slave, unsigned int bitlen,
> +			  const void *tx_buf, void *rx_buf,
> +			  unsigned long flags)
> +{
> +	struct dm_spi_slave_platdata *slave_plat;
> +	struct udevice *bus = slave->parent;
> +	struct pic32_spi_priv *priv;
> +	int len = bitlen / 8;
> +	int ret = 0;
> +	ulong tbase;
> +
> +	priv = dev_get_priv(bus);
> +	slave_plat = dev_get_parent_platdata(slave);
> +
> +	debug("spi_xfer: bus:%i cs:%i flags:%lx\n",
> +	      bus->seq, slave_plat->cs, flags);
> +	debug("msg tx %p, rx %p submitted of %d byte(s)\n",
> +	      tx_buf, rx_buf, len);
> +
> +	/* assert cs */
> +	if (flags & SPI_XFER_BEGIN)
> +		spi_cs_activate(priv);
> +
> +	/* set current transfer information */
> +	priv->tx = tx_buf;
> +	priv->rx = rx_buf;
> +	priv->tx_end = priv->tx + len;
> +	priv->rx_end = priv->rx + len;
> +	priv->len = len;
> +
> +	/* transact by polling */
> +	tbase = get_timer(0);
> +	for (;;) {
> +		priv->tx_fifo(priv);
> +		priv->rx_fifo(priv);
> +
> +		/* received sufficient data */
> +		if (priv->rx >= priv->rx_end) {
> +			ret = 0;
> +			break;
> +		}
> +
> +		if (get_timer(tbase) > 5 * CONFIG_SYS_HZ) {
> +			printf("pic32_spi: error, xfer timedout.\n");
> +			flags |= SPI_XFER_END;
> +			ret = -ETIMEDOUT;
> +			break;
> +		}
> +	}
> +
> +	/* deassert cs */
> +	if (flags & SPI_XFER_END)
> +		spi_cs_deactivate(priv);
> +
> +	return ret;
> +}
> +
> +static int pic32_spi_set_speed(struct udevice *bus, uint speed)
> +{
> +	struct pic32_spi_priv *priv = dev_get_priv(bus);
> +	u32 div;
> +
> +	debug("%s: %s, speed %u\n", __func__, bus->name, speed);
> +
> +	/* div = [clk_in / (2 * spi_clk)] - 1 */
> +	div = (priv->clk_rate / 2 / speed) - 1;
> +	div &= PIC32_SPI_BAUD_MASK;
> +	writel(div, &priv->regs->baud.raw);
> +
> +	priv->speed_hz = speed;
> +
> +	return 0;
> +}
> +
> +static int pic32_spi_set_mode(struct udevice *bus, uint mode)
> +{
> +	struct pic32_spi_priv *priv = dev_get_priv(bus);
> +	u32 val;
> +
> +	debug("%s: %s, mode %d\n", __func__, bus->name, mode);
> +
> +	/* set spi-clk mode */
> +	val = readl(&priv->regs->ctrl.raw);
> +	/* HIGH when idle */
> +	if (mode & SPI_CPOL)
> +		val |= PIC32_SPI_CTRL_CKP;
> +	else
> +		val &= ~PIC32_SPI_CTRL_CKP;
> +
> +	/* TX at idle-to-active clk transition */
> +	if (mode & SPI_CPHA)
> +		val &= ~PIC32_SPI_CTRL_CKE;
> +	else
> +		val |= PIC32_SPI_CTRL_CKE;
> +
> +	/* RX at end of tx */
> +	val |= PIC32_SPI_CTRL_SMP;
> +	writel(val, &priv->regs->ctrl.raw);
> +
> +	priv->mode = mode;
> +
> +	return 0;
> +}
> +
> +static int pic32_spi_set_wordlen(struct udevice *slave, unsigned int wordlen)
> +{
> +	struct pic32_spi_priv *priv = dev_get_priv(slave->parent);
> +
> +	return pic32_spi_set_word_size(priv, wordlen);
> +}
> +
> +static void pic32_spi_hw_init(struct pic32_spi_priv *priv)
> +{
> +	u32 val;
> +
> +	/* disable module */
> +	pic32_spi_disable(priv);
> +
> +	val = readl(&priv->regs->ctrl);
> +
> +	/* enable enhanced fifo of 128bit deep */
> +	val |= PIC32_SPI_CTRL_ENHBUF;
> +	priv->fifo_depth = 16;
> +
> +	/* disable framing mode */
> +	val &= ~PIC32_SPI_CTRL_FRMEN;
> +
> +	/* enable master mode */
> +	val |= PIC32_SPI_CTRL_MSTEN;
> +
> +	/* select clk source */
> +	val &= ~PIC32_SPI_CTRL_MCLKSEL;
> +
> +	/* set manual /CS mode */
> +	val &= ~PIC32_SPI_CTRL_MSSEN;
> +
> +	writel(val, &priv->regs->ctrl);
> +
> +	/* clear rx overflow indicator */
> +	writel(PIC32_SPI_STAT_RX_OV, &priv->regs->status.clr);
> +}
> +
> +static int pic32_spi_probe(struct udevice *bus)
> +{
> +	struct pic32_spi_priv *priv = dev_get_priv(bus);
> +	struct dm_spi_bus *dm_spi = dev_get_uclass_priv(bus);
> +	struct udevice *clkdev;
> +	fdt_addr_t addr;
> +	fdt_size_t size;
> +	int ret;
> +
> +	debug("%s: %d, bus: %i\n", __func__, __LINE__, bus->seq);
> +	addr = fdtdec_get_addr_size(gd->fdt_blob, bus->of_offset, "reg", &size);
> +	if (addr == FDT_ADDR_T_NONE)
> +		return -EINVAL;
> +
> +	priv->regs = ioremap(addr, size);
> +	if (!priv->regs)
> +		return -EINVAL;
> +
> +	dm_spi->max_hz = fdtdec_get_int(gd->fdt_blob, bus->of_offset,
> +					"spi-max-frequency", 250000000);
> +	/* get clock rate */
> +	ret = clk_get_by_index(bus, 0, &clkdev);
> +	if (ret < 0) {
> +		printf("pic32-spi: error, clk not found\n");
> +		return ret;
> +	}
> +	priv->clk_rate = clk_get_periph_rate(clkdev, ret);
> +
> +	/* initialize HW */
> +	pic32_spi_hw_init(priv);
> +
> +	/* set word len */
> +	pic32_spi_set_word_size(priv, SPI_DEFAULT_WORDLEN);
> +
> +	/* PIC32 SPI controller can automatically drive /CS during transfer
> +	 * depending on fifo fill-level. /CS will stay asserted as long as
> +	 * TX fifo is non-empty, else will be deasserted confirming completion
> +	 * of the ongoing transfer. To avoid this sort of error we will drive
> +	 * /CS manually by toggling cs-gpio pins.
> +	 */
> +	ret = gpio_request_by_name_nodev(gd->fdt_blob, bus->of_offset,
> +					 "cs-gpios", 0,
> +					 &priv->cs_gpio, GPIOD_IS_OUT);
> +	if (ret) {
> +		printf("pic32-spi: error, cs-gpios not found\n");
> +		return ret;
> +	}
> +
> +	return 0;
> +}
> +
> +static const struct dm_spi_ops pic32_spi_ops = {
> +	.claim_bus	= pic32_spi_claim_bus,
> +	.release_bus	= pic32_spi_release_bus,
> +	.xfer		= pic32_spi_xfer,
> +	.set_speed	= pic32_spi_set_speed,
> +	.set_mode	= pic32_spi_set_mode,
> +	.set_wordlen	= pic32_spi_set_wordlen,
> +};
> +
> +static const struct udevice_id pic32_spi_ids[] = {
> +	{ .compatible = "microchip,pic32mzda-spi" },
> +	{ }
> +};
> +
> +U_BOOT_DRIVER(pic32_spi) = {
> +	.name		= "pic32_spi",
> +	.id		= UCLASS_SPI,
> +	.of_match	= pic32_spi_ids,
> +	.ops		= &pic32_spi_ops,
> +	.priv_auto_alloc_size = sizeof(struct pic32_spi_priv),
> +	.probe		= pic32_spi_probe,
> +};
> 

-- 
- Daniel

-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 473 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20160603/d92ae6ee/attachment.sig>


More information about the U-Boot mailing list