[U-Boot] [PATCH] sunxi: Add defconfig and dts file for inet86dz board

Hans de Goede hdegoede at redhat.com
Sun Jun 12 19:50:10 CEST 2016 

The inet86dz board is a board used in 7" tablets from various oems.

These tablets are a23 based 7" tablets featuring a 1024x600 LCD,
512MB RAM, 4G NAND, rtl8188etv usb wifi, gsl1680 touchschreen,
micro-sd slot, 3.5mm headphone jack and a micro-usb otg connector
which doubles as charging port.

The dts file this commit adds is identical to the one submitted to
the upstream kernel.

Signed-off-by: Hans de Goede <hdegoede at redhat.com>
---
 arch/arm/dts/Makefile               |   1 +
 arch/arm/dts/sun8i-a23-inet86dz.dts | 293 ++++++++++++++++++++++++++++++++++++
 board/sunxi/MAINTAINERS             |   1 +
 configs/inet86dz_defconfig          |  24 +++
 4 files changed, 319 insertions(+)
 create mode 100644 arch/arm/dts/sun8i-a23-inet86dz.dts
 create mode 100644 configs/inet86dz_defconfig

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index f76475e..efbe34a 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -216,6 +216,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \
 dtb-$(CONFIG_MACH_SUN8I_A23) += \
 	sun8i-a23-evb.dtb \
 	sun8i-a23-gt90h-v4.dtb \
+	sun8i-a23-inet86dz.dtb \
 	sun8i-a23-polaroid-mid2407pxe03.dtb \
 	sun8i-a23-polaroid-mid2809pxe04.dtb \
 	sun8i-a23-q8-tablet.dtb
diff --git a/arch/arm/dts/sun8i-a23-inet86dz.dts b/arch/arm/dts/sun8i-a23-inet86dz.dts
new file mode 100644
index 0000000..0405258
--- /dev/null
+++ b/arch/arm/dts/sun8i-a23-inet86dz.dts
@@ -0,0 +1,293 @@
+/*
+ * Copyright 2016 Hans de Goede <hdegoede at redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-a23.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	model = "INet-86DZ Rev 01";
+	compatible = "primux,inet86dz", "allwinner,sun8i-a23";
+
+	aliases {
+		serial0 = &r_uart;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&bl_en_pin_inet86dz>;
+		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+		default-brightness-level = <8>;
+		enable-gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+	/*
+	 * The gsl1680 is rated at 400KHz and it will not work reliable at
+	 * 100KHz, this has been confirmed on multiple different tablets.
+	 * The gsl1680 is the only device on this bus.
+	 */
+	clock-frequency = <400000>;
+
+	gsl1680: touchscreen at 40 {
+		compatible = "silead,gsl1680";
+		reg = <0x40>;
+		interrupt-parent = <&pio>;
+		interrupts = <1 5 IRQ_TYPE_EDGE_FALLING>; /* PB5 */
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_power_pin_inet86dz>;
+		power-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+		touchscreen-size-x = <960>;
+		touchscreen-size-y = <640>;
+		touchscreen-max-fingers = <5>;
+		touchscreen-fw-name = "silead/gsl1680-inet86dz.fw";
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_a>;
+	status = "okay";
+};
+
+&lradc {
+	vref-supply = <&reg_vcc3v0>;
+	status = "okay";
+
+	button at 200 {
+		label = "Volume Up";
+		linux,code = <KEY_VOLUMEUP>;
+		channel = <0>;
+		voltage = <200000>;
+	};
+
+	button at 400 {
+		label = "Volume Down";
+		linux,code = <KEY_VOLUMEDOWN>;
+		channel = <0>;
+		voltage = <400000>;
+	};
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_inet86dz>;
+	vmmc-supply = <&reg_dcdc1>;
+	bus-width = <4>;
+	cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
+	cd-inverted;
+	status = "okay";
+};
+
+&pio {
+	bl_en_pin_inet86dz: bl_en_pin at 0 {
+		allwinner,pins = "PH6";
+		allwinner,function = "gpio_in";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
+	mmc0_cd_pin_inet86dz: mmc0_cd_pin at 0 {
+		allwinner,pins = "PB4";
+		allwinner,function = "gpio_in";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+	};
+
+	ts_power_pin_inet86dz: ts_power_pin at 0 {
+		allwinner,pins = "PH1";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
+	usb0_id_detect_pin: usb0_id_detect_pin at 0 {
+		allwinner,pins = "PH8";
+		allwinner,function = "gpio_in";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_pins>;
+	status = "okay";
+};
+
+&r_rsb {
+	status = "okay";
+
+	axp22x: pmic at 3a3 {
+		compatible = "x-powers,axp223";
+		reg = <0x3a3>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		eldoin-supply = <&reg_dcdc1>;
+		x-powers,drive-vbus-en;
+	};
+};
+
+&r_uart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&r_uart_pins_a>;
+	status = "okay";
+};
+
+#include "axp22x.dtsi"
+
+&reg_aldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-io";
+};
+
+&reg_aldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <2350000>;
+	regulator-max-microvolt = <2650000>;
+	regulator-name = "vdd-dll";
+};
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <2700000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-pll-avcc";
+};
+
+&reg_dc1sw {
+	regulator-name = "vcc-lcd";
+};
+
+&reg_dc5ldo {
+	regulator-always-on;
+	regulator-min-microvolt = <900000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-cpus";
+};
+
+&reg_dcdc1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "vcc-3v0";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <900000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-sys";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <900000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1500000>;
+	regulator-max-microvolt = <1500000>;
+	regulator-name = "vcc-dram";
+};
+
+&reg_dldo1 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi";
+};
+
+&reg_drivevbus {
+	regulator-name = "usb0-vbus";
+	status = "okay";
+};
+
+&reg_rtc_ldo {
+	regulator-name = "vcc-rtc";
+};
+
+&simplefb_lcd {
+	vcc-lcd-supply = <&reg_dc1sw>;
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb_power_supply {
+	status = "okay";
+};
+
+&usbphy {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_id_detect_pin>;
+	usb0_id_det-gpio = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
+	usb0_vbus_power-supply = <&usb_power_supply>;
+	usb0_vbus-supply = <&reg_drivevbus>;
+	usb1_vbus-supply = <&reg_dldo1>;
+	status = "okay";
+};
diff --git a/board/sunxi/MAINTAINERS b/board/sunxi/MAINTAINERS
index 4f8d950..de5207e 100644
--- a/board/sunxi/MAINTAINERS
+++ b/board/sunxi/MAINTAINERS
@@ -54,6 +54,7 @@ F:	configs/Wits_Pro_A20_DKT_defconfig
 F:	include/configs/sun8i.h
 F:	configs/ga10h_v1_1_defconfig
 F:	configs/gt90h_v4_defconfig
+F:	configs/inet86dz_defconfig
 F:	configs/orangepi_2_defconfig
 F:	configs/orangepi_one_defconfig
 F:	configs/orangepi_pc_defconfig
diff --git a/configs/inet86dz_defconfig b/configs/inet86dz_defconfig
new file mode 100644
index 0000000..55768ba
--- /dev/null
+++ b/configs/inet86dz_defconfig
@@ -0,0 +1,24 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN8I_A23=y
+CONFIG_DRAM_CLK=552
+CONFIG_DRAM_ZQ=63351
+CONFIG_MMC0_CD_PIN="PB4"
+CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
+CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
+CONFIG_USB0_ID_DET="PH8"
+CONFIG_AXP_GPIO=y
+CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:18,pclk_khz:51000,le:138,ri:162,up:22,lo:10,hs:20,vs:3,sync:3,vmode:0"
+CONFIG_VIDEO_LCD_DCLK_PHASE=0
+CONFIG_VIDEO_LCD_POWER="PH7"
+CONFIG_VIDEO_LCD_BL_EN="PH6"
+CONFIG_VIDEO_LCD_BL_PWM="PH0"
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-a23-inet86dz"
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=5"
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+CONFIG_AXP_DLDO1_VOLT=3300
+CONFIG_USB_MUSB_HOST=y
-- 
2.7.4

More information about the U-Boot mailing list