[U-Boot] [PATCH v2 4/8] ARM: AM33xx: Add support for Clock Synthesizer

[Lokesh Vutla]

The CDCE913 and CDCEL913 devices are modular PLL-based, low cost,
high performance , programmable clock synthesizers. They generate
upto 3 output clocks from a single input frequency. Each output can
be programmed for any clock-frequency.

Adding support for the same.

Reviewed-by: Tom Rini <trini at konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla at ti.com>
---
Changes since v1:
- None

 arch/arm/cpu/armv7/am33xx/Makefile                 |   2 +
 arch/arm/cpu/armv7/am33xx/clk_synthesizer.c        | 104 +++++++++++++++++++++
 arch/arm/include/asm/arch-am33xx/clk_synthesizer.h |  43 +++++++++
 3 files changed, 149 insertions(+)
 create mode 100644 arch/arm/cpu/armv7/am33xx/clk_synthesizer.c
 create mode 100644 arch/arm/include/asm/arch-am33xx/clk_synthesizer.h

diff --git a/arch/arm/cpu/armv7/am33xx/Makefile b/arch/arm/cpu/armv7/am33xx/Makefile
index aae3f09..6fda482 100644
--- a/arch/arm/cpu/armv7/am33xx/Makefile
+++ b/arch/arm/cpu/armv7/am33xx/Makefile
@@ -18,3 +18,5 @@ obj-y	+= ddr.o
 obj-y	+= emif4.o
 obj-y	+= board.o
 obj-y	+= mux.o
+
+obj-$(CONFIG_CLOCK_SYNTHESIZER)	+= clk_synthesizer.o
diff --git a/arch/arm/cpu/armv7/am33xx/clk_synthesizer.c b/arch/arm/cpu/armv7/am33xx/clk_synthesizer.c
new file mode 100644
index 0000000..316e677
--- /dev/null
+++ b/arch/arm/cpu/armv7/am33xx/clk_synthesizer.c
@@ -0,0 +1,104 @@
+/*
+ * clk-synthesizer.c
+ *
+ * Clock synthesizer apis
+ *
+ * Copyright (C) 2016, Texas Instruments, Incorporated - http://www.ti.com/
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+
+#include <common.h>
+#include <asm/arch/clk_synthesizer.h>
+#include <i2c.h>
+
+/**
+ * clk_synthesizer_reg_read - Read register from synthesizer.
+ * @addr:	addr within the i2c device
+ * buf:		Buffer to which value is to be read.
+ *
+ * For reading the register from this clock synthesizer, a command needs to
+ * be send along with enabling byte read more, and then read can happen.
+ * Returns 0 on success
+ */
+static int clk_synthesizer_reg_read(int addr, uint8_t *buf)
+{
+	int rc;
+
+	/* Enable Bye read */
+	addr = addr | CLK_SYNTHESIZER_BYTE_MODE;
+
+	/* Send the command byte */
+	rc = i2c_write(CLK_SYNTHESIZER_I2C_ADDR, addr, 1, buf, 1);
+	if (rc)
+		printf("Failed to send command to clock synthesizer\n");
+
+	/* Read the Data */
+	return i2c_read(CLK_SYNTHESIZER_I2C_ADDR, addr, 1, buf, 1);
+}
+
+/**
+ * clk_synthesizer_reg_write - Write a value to register in synthesizer.
+ * @addr:	addr within the i2c device
+ * val:		Value to be written in the addr.
+ *
+ * Enable the byte read mode in the address and start the i2c transfer.
+ * Returns 0 on success
+ */
+static int clk_synthesizer_reg_write(int addr, uint8_t val)
+{
+	uint8_t cmd[2];
+	int rc = 0;
+
+	/* Enable byte write */
+	cmd[0] = addr | CLK_SYNTHESIZER_BYTE_MODE;
+	cmd[1] = val;
+
+	rc = i2c_write(CLK_SYNTHESIZER_I2C_ADDR, addr, 1, cmd, 2);
+	if (rc)
+		printf("Clock synthesizer reg write failed at addr = 0x%x\n",
+		       addr);
+	return rc;
+}
+
+/**
+ * setup_clock_syntherizer - Program the clock synthesizer to get the desired
+ *				frequency.
+ * @data: Data containing the desired output
+ *
+ * This is a PLL-based high performance synthesizer which gives 3 outputs
+ * as per the PLL_DIV and load capacitor programmed.
+ */
+int setup_clock_synthesizer(struct clk_synth *data)
+{
+	int rc;
+	uint8_t val;
+
+	rc =  i2c_probe(CLK_SYNTHESIZER_I2C_ADDR);
+	if (rc) {
+		printf("i2c probe failed at address 0x%x\n",
+		       CLK_SYNTHESIZER_I2C_ADDR);
+		return rc;
+	}
+
+	rc = clk_synthesizer_reg_read(CLK_SYNTHESIZER_ID_REG, &val);
+	if (val != data->id)
+		return rc;
+
+	/* Crystal Load capacitor selection */
+	rc = clk_synthesizer_reg_write(CLK_SYNTHESIZER_XCSEL, data->capacitor);
+	if (rc)
+		return rc;
+	rc = clk_synthesizer_reg_write(CLK_SYNTHESIZER_MUX_REG, data->mux);
+	if (rc)
+		return rc;
+	rc = clk_synthesizer_reg_write(CLK_SYNTHESIZER_PDIV2_REG, data->pdiv2);
+	if (rc)
+		return rc;
+	rc = clk_synthesizer_reg_write(CLK_SYNTHESIZER_PDIV3_REG, data->pdiv3);
+	if (rc)
+		return rc;
+
+	return 0;
+}
diff --git a/arch/arm/include/asm/arch-am33xx/clk_synthesizer.h b/arch/arm/include/asm/arch-am33xx/clk_synthesizer.h
new file mode 100644
index 0000000..a5af012
--- /dev/null
+++ b/arch/arm/include/asm/arch-am33xx/clk_synthesizer.h
@@ -0,0 +1,43 @@
+/*
+ * clk-synthesizer.h
+ *
+ * Clock synthesizer header
+ *
+ * Copyright (C) 2016, Texas Instruments, Incorporated - http://www.ti.com/
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CLK_SYNTHESIZER_H
+#define __CLK_SYNTHESIZER_H
+
+#include <common.h>
+
+#define CLK_SYNTHESIZER_ID_REG		0x0
+#define CLK_SYNTHESIZER_XCSEL		0x05
+#define CLK_SYNTHESIZER_MUX_REG		0x14
+#define CLK_SYNTHESIZER_PDIV2_REG	0x16
+#define CLK_SYNTHESIZER_PDIV3_REG	0x17
+
+#define CLK_SYNTHESIZER_BYTE_MODE	0x80
+
+/**
+ * struct clk_synth: This structure holds data neeed for configuring
+ *		     for clock synthesizer.
+ * @id: The id of synthesizer
+ * @capacitor: value of the capacitor attached
+ * @mux: mux settings.
+ * @pdiv2: Div to be applied to second output
+ * @pdiv3: Div to be applied to third output
+ */
+struct clk_synth {
+	u32 id;
+	u32 capacitor;
+	u32 mux;
+	u32 pdiv2;
+	u32 pdiv3;
+};
+
+int setup_clock_synthesizer(struct clk_synth *data);
+
+#endif
-- 
2.8.2