[U-Boot] [PATCH] ARM: sun7i: dts: add support for Sinovoip/Bananapi BPI-R1
Stephen Arnold
stephen.arnold42 at gmail.com
Mon Oct 3 18:42:01 CEST 2016
On Sun, Oct 2, 2016 at 11:55 PM, Hans de Goede <hdegoede at redhat.com> wrote:
> Hi,
>
> On 02-10-16 06:36, Stephen Arnold wrote:
>>
>> From: Steve Arnold <stephen.arnold42 at gmail.com>
>>
>> * needs different GMAC_TX_DELAY than lamobo-r1 (not compatible)
>
>
> I see why this would need a separate defconfig, but why do you also
> need a new dts file ?
I don't have a lamobo to test on, however, several dts things seem
"broken" when trying to run the bananapi with lamobo config, mostly
from memory:
1) uart3 has incorrect pin setting
2) USB host doesn't work (so you get u-boot console but no keyboard)
3) ahci power pin seems to make it less than stable (odd behavior
building native with sata rootfs)
4) missing i2c on the rpi pin header
plus a few more odds and ends.
> And if you need just a minor dts tweak, please just include the
> existing dts file and make the tweak, rather then writing a
> whole new dts file.
What exactly qualifies as a "minor tweak"? This seems like more than that...
> Also have you submitted the dts file to the upstream kernel ?
Not yet, but it kinda needs u-boot in order to work, so I submitted
here first. The kernel dts needs even more tweaks to make cpufreq and
voltage adjustments correctly; now with a tiny heatsink it idles at ~
42 C instead of 49/50 deg C.
Lastly, I could not get "compatible" to do much here; the only way I
could boot my bananapi-r1 test (kernel) dts was to make a symlink from
lamobo-r1.dts to bananapi-r1.dts. I couldn't find an example of two
similar-enough boards sharing a dts file with two different names as
"compatible". Is there such an example somewhere and I missed it?
Thanks, Steve
> Regards,
>
> Hans
>
>
>
>
>> * tested with 4.8_rc6 b53-mdio and kernel dts switch nodes
>>
>> Signed-off-by: Steve Arnold <nerdboy at gentoo.org>
>> ---
>> arch/arm/dts/Makefile | 1 +
>> arch/arm/dts/sun7i-a20-bananapi-r1.dts | 321
>> +++++++++++++++++++++++++++++++++
>> configs/Bananapi_R1_defconfig | 19 ++
>> 3 files changed, 341 insertions(+)
>> create mode 100644 arch/arm/dts/sun7i-a20-bananapi-r1.dts
>> create mode 100644 configs/Bananapi_R1_defconfig
>>
>> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
>> index 032c5ae..0cbae00 100644
>> --- a/arch/arm/dts/Makefile
>> +++ b/arch/arm/dts/Makefile
>> @@ -216,6 +216,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \
>> sun7i-a20-ainol-aw1.dtb \
>> sun7i-a20-bananapi.dtb \
>> sun7i-a20-bananapi-m1-plus.dtb \
>> + sun7i-a20-bananapi-r1.dtb \
>> sun7i-a20-bananapro.dtb \
>> sun7i-a20-cubieboard2.dtb \
>> sun7i-a20-cubietruck.dtb \
>> diff --git a/arch/arm/dts/sun7i-a20-bananapi-r1.dts
>> b/arch/arm/dts/sun7i-a20-bananapi-r1.dts
>> new file mode 100644
>> index 0000000..30a827f
>> --- /dev/null
>> +++ b/arch/arm/dts/sun7i-a20-bananapi-r1.dts
>> @@ -0,0 +1,321 @@
>> +/*
>> + * Copyright 2015 Hans de Goede <hdegoede at redhat.com>
>> + *
>> + * Changes copyright 2015 Stephen Arnold <nerdboy at gentoo.org>
>> + * This file is dual-licensed: you can use it either under the terms
>> + * of the GPL or the X11 license, at your option. Note that this dual
>> + * licensing only applies to this file, and not this project as a
>> + * whole.
>> + *
>> + * a) This file is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation; either version 2 of the
>> + * License, or (at your option) any later version.
>> + *
>> + * This file is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + *
>> + * Or, alternatively,
>> + *
>> + * b) Permission is hereby granted, free of charge, to any person
>> + * obtaining a copy of this software and associated documentation
>> + * files (the "Software"), to deal in the Software without
>> + * restriction, including without limitation the rights to use,
>> + * copy, modify, merge, publish, distribute, sublicense, and/or
>> + * sell copies of the Software, and to permit persons to whom the
>> + * Software is furnished to do so, subject to the following
>> + * conditions:
>> + *
>> + * The above copyright notice and this permission notice shall be
>> + * included in all copies or substantial portions of the Software.
>> + *
>> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
>> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
>> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
>> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
>> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
>> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
>> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
>> + * OTHER DEALINGS IN THE SOFTWARE.
>> + */
>> +
>> +/dts-v1/;
>> +#include "sun7i-a20.dtsi"
>> +#include "sunxi-common-regulators.dtsi"
>> +
>> +#include <dt-bindings/gpio/gpio.h>
>> +#include <dt-bindings/interrupt-controller/irq.h>
>> +#include <dt-bindings/pinctrl/sun4i-a10.h>
>> +
>> +/ {
>> + model = "Banana Pi BPI-R1";
>> + compatible = "sinovoip,bpi-r1", "allwinner,sun7i-a20";
>> +
>> + aliases {
>> + serial0 = &uart0;
>> + serial1 = &uart2;
>> + serial2 = &uart3;
>> + serial3 = &uart7;
>> + };
>> +
>> + chosen {
>> + stdout-path = "serial0:115200n8";
>> + };
>> +
>> + leds {
>> + compatible = "gpio-leds";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&led_pins_bpi_r1>;
>> +
>> + green {
>> + label = "bpi-r1:green:usr";
>> + gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>; /* PH24 */
>> + linux,default-trigger = "heartbeat";
>> + };
>> + };
>> +
>> + reg_gmac_3v3: gmac-3v3 {
>> + compatible = "regulator-fixed";
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&gmac_power_pin_bpi_r1>;
>> + regulator-name = "gmac-3v3";
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + startup-delay-us = <100000>;
>> + enable-active-high;
>> + gpio = <&pio 7 23 GPIO_ACTIVE_HIGH>; /* PH23 */
>> + };
>> +
>> +};
>> +
>> +&ahci {
>> + target-supply = <®_ahci_5v>;
>> + status = "okay";
>> +};
>> +
>> +&cpu0 {
>> + cpu-supply = <®_dcdc2>;
>> +};
>> +
>> +&ehci0 {
>> + status = "okay";
>> +};
>> +
>> +&ehci1 {
>> + status = "okay";
>> +};
>> +
>> +&ohci0 {
>> + status = "okay";
>> +};
>> +
>> +&ohci1 {
>> + status = "okay";
>> +};
>> +
>> +&gmac {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&gmac_pins_rgmii_a>;
>> + phy = <&phy1>;
>> + phy-mode = "rgmii";
>> + phy-supply = <®_gmac_3v3>;
>> + status = "okay";
>> +
>> + phy1: ethernet-phy at 1 {
>> + reg = <1>;
>> + };
>> +};
>> +
>> +&i2c0 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&i2c0_pins_a>;
>> + status = "okay";
>> +
>> + axp209: pmic at 34 {
>> + compatible = "x-powers,axp209";
>> + reg = <0x34>;
>> + interrupt-parent = <&nmi_intc>;
>> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
>> +
>> + interrupt-controller;
>> + #interrupt-cells = <1>;
>> + };
>> +};
>> +
>> +#include "axp209.dtsi"
>> +
>> +&i2c2 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&i2c2_pins_a>;
>> + status = "okay";
>> +};
>> +
>> +&ir0 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&ir0_rx_pins_a>;
>> + status = "okay";
>> +};
>> +
>> +&mmc0 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bpi_r1>;
>> + vmmc-supply = <®_vcc3v3>;
>> + bus-width = <4>;
>> + cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
>> + cd-inverted;
>> + status = "okay";
>> +};
>> +
>> +&otg_sram {
>> + status = "okay";
>> +};
>> +
>> +&pio {
>> + usb0_id_detect_pin: usb0_id_detect_pin at 0 {
>> + allwinner,pins = "PH4";
>> + allwinner,function = "gpio_in";
>> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> + };
>> +
>> + usb0_vbus_detect_pin: usb0_vbus_detect_pin at 0 {
>> + allwinner,pins = "PH5";
>> + allwinner,function = "gpio_in";
>> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> + };
>> +
>> + usb0_vbus_pin_bpi_r1: usb0_vbus_pin at 0 {
>> + allwinner,pins = "PB9";
>> + allwinner,function = "gpio_out";
>> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> + };
>> +
>> + usb2_vbus_pin_bpi_r1: usb2_vbus_pin at 0 {
>> + allwinner,pins = "PH3";
>> + allwinner,function = "gpio_out";
>> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> + };
>> +
>> + mmc0_cd_pin_bpi_r1: mmc0_cd_pin at 0 {
>> + allwinner,pins = "PH1";
>> + allwinner,function = "gpio_in";
>> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
>> + };
>> +
>> + gmac_power_pin_bpi_r1: gmac_power_pin at 0 {
>> + allwinner,pins = "PH23";
>> + allwinner,function = "gpio_out";
>> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> + };
>> +
>> + led_pins_bpi_r1: led_pins at 0 {
>> + allwinner,pins = "PH24";
>> + allwinner,function = "gpio_out";
>> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> + };
>> +};
>> +
>> +®_ahci_5v {
>> + status = "okay";
>> +};
>> +
>> +®_dcdc2 {
>> + regulator-always-on;
>> + regulator-min-microvolt = <1000000>;
>> + regulator-max-microvolt = <1400000>;
>> + regulator-name = "vdd-cpu";
>> +};
>> +
>> +®_dcdc3 {
>> + regulator-always-on;
>> + regulator-min-microvolt = <1000000>;
>> + regulator-max-microvolt = <1400000>;
>> + regulator-name = "vdd-int-dll";
>> +};
>> +
>> +®_ldo1 {
>> + regulator-name = "vdd-rtc";
>> +};
>> +
>> +®_ldo2 {
>> + regulator-always-on;
>> + regulator-min-microvolt = <3000000>;
>> + regulator-max-microvolt = <3000000>;
>> + regulator-name = "avcc";
>> +};
>> +
>> +®_usb0_vbus {
>> + pinctrl-0 = <&usb0_vbus_pin_bpi_r1>;
>> + gpio = <&pio 1 9 GPIO_ACTIVE_HIGH>; /* PB9 */
>> + status = "okay";
>> +};
>> +
>> +®_usb1_vbus {
>> + status = "okay";
>> +};
>> +
>> +®_usb2_vbus {
>> + pinctrl-0 = <&usb2_vbus_pin_bpi_r1>;
>> + gpio = <&pio 7 3 GPIO_ACTIVE_HIGH>; /* PH3 */
>> + status = "okay";
>> +};
>> +
>> +&spi0 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&spi0_pins_a>,
>> + <&spi0_cs0_pins_a>,
>> + <&spi0_cs1_pins_a>;
>> + status = "okay";
>> +};
>> +
>> +&uart0 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&uart0_pins_a>;
>> + status = "okay";
>> +};
>> +
>> +&uart2 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&uart2_pins_a>;
>> + status = "okay";
>> +};
>> +
>> +&uart3 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&uart3_pins_b>;
>> + status = "okay";
>> +};
>> +
>> +&uart7 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&uart7_pins_a>;
>> + status = "okay";
>> +};
>> +
>> +&usb_otg {
>> + dr_mode = "otg";
>> + status = "okay";
>> +};
>> +
>> +&usb_power_supply {
>> + status = "okay";
>> +};
>> +
>> +&usbphy {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&usb0_id_detect_pin>;
>> + usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
>> + usb0_vbus_power-supply = <&usb_power_supply>;
>> + usb0_vbus-supply = <®_usb0_vbus>;
>> + usb1_vbus-supply = <®_usb1_vbus>;
>> + usb2_vbus-supply = <®_usb2_vbus>;
>> + status = "okay";
>> +};
>> diff --git a/configs/Bananapi_R1_defconfig b/configs/Bananapi_R1_defconfig
>> new file mode 100644
>> index 0000000..e5341ee
>> --- /dev/null
>> +++ b/configs/Bananapi_R1_defconfig
>> @@ -0,0 +1,19 @@
>> +CONFIG_ARM=y
>> +CONFIG_ARCH_SUNXI=y
>> +CONFIG_MACH_SUN7I=y
>> +CONFIG_DRAM_CLK=432
>> +CONFIG_GMAC_TX_DELAY=3
>> +CONFIG_DEFAULT_DEVICE_TREE="sun7i-a20-bananapi-r1"
>> +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
>> +CONFIG_SPL=y
>>
>> +CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_GMAC,RGMII,MACPWR=SUNXI_GPH(23),AHCI,USB_EHCI"
>> +# CONFIG_CMD_IMLS is not set
>> +# CONFIG_CMD_FLASH is not set
>> +# CONFIG_CMD_FPGA is not set
>
>
>> +CONFIG_DM_ETH=y
>> +CONFIG_PHYLIB=y
>> +# CONFIG_RTL8211X_PHY_FORCE_MASTER=y
>
>
> There is no need to set these 3 options, they are the default.
>
>> +CONFIG_ETH_DESIGNWARE=y
>
>
>> +CONFIG_DM_SERIAL=y
>> +CONFIG_USB=y
>> +CONFIG_DM_USB=y
>
>
> Likewise for these 3 options, they are on by default too.
>
> OTOH you do like want to do:
>
> CONFIG_USB_EHCI_HCD=y
>
> So that the usb ports will work in u-boot.
>
> Regards,
>
> Hans
More information about the U-Boot
mailing list