[U-Boot] [PATCH] [PATCH 2/2] ARM: sun7i: dts: add support for Sinovoip/Bananapi BPI-R1
Stephen Arnold
stephen.arnold42 at gmail.com
Mon Oct 3 22:01:04 CEST 2016
From: Steve Arnold <stephen.arnold42 at gmail.com>
* changes from lamobo-r1 required include:
- ahci power pin (remove)
- usbvbus pin config
- mmc pin config
- uart2 enable
Signed-off-by: Steve Arnold <stephen.arnold42 at gmail.com>
---
arch/arm/dts/Makefile | 1 +
arch/arm/dts/sun7i-a20-bananapi-r1.dts | 376 +++++++++++++++++++++++++++++++++
2 files changed, 377 insertions(+)
create mode 100644 arch/arm/dts/sun7i-a20-bananapi-r1.dts
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 032c5ae..0cbae00 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -216,6 +216,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \
sun7i-a20-ainol-aw1.dtb \
sun7i-a20-bananapi.dtb \
sun7i-a20-bananapi-m1-plus.dtb \
+ sun7i-a20-bananapi-r1.dtb \
sun7i-a20-bananapro.dtb \
sun7i-a20-cubieboard2.dtb \
sun7i-a20-cubietruck.dtb \
diff --git a/arch/arm/dts/sun7i-a20-bananapi-r1.dts b/arch/arm/dts/sun7i-a20-bananapi-r1.dts
new file mode 100644
index 0000000..1a550f9
--- /dev/null
+++ b/arch/arm/dts/sun7i-a20-bananapi-r1.dts
@@ -0,0 +1,376 @@
+/*
+ * Copyright 2015 Hans de Goede <hdegoede at redhat.com>
+ * Changes copyright 2016 Stephen Arnold <nerdboy at gentoo.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Banana Pi BPI-R1";
+ compatible = "sinovoip,bpi-r1", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart2;
+ serial2 = &uart3;
+ serial3 = &uart7;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_bpi_r1>;
+
+ green {
+ label = "bpi-r1:green:usr";
+ gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>; /* PH24 */
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_power_pin_bpi_r1>;
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ enable-active-high;
+ gpio = <&pio 7 23 GPIO_ACTIVE_HIGH>; /* PH23 */
+ };
+
+};
+
+&ahci {
+ target-supply = <®_ahci_5v>;
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_rgmii_a>;
+ phy = <&phy1>;
+ phy-mode = "rgmii";
+ phy-supply = <®_gmac_3v3>;
+ status = "okay";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch: ethernet-switch at 1e {
+ compatible = "brcm,bcm53125";
+ reg = <30>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port0: port at 0 {
+ reg = <0>;
+ label = "lan2";
+ };
+
+ port1: port at 1 {
+ reg = <1>;
+ label = "lan3";
+ };
+
+ port2: port at 2 {
+ reg = <2>;
+ label = "lan4";
+ };
+
+ port3: port at 3 {
+ reg = <3>;
+ label = "wan";
+ };
+
+ port4: port at 4 {
+ reg = <4>;
+ label = "lan1";
+ };
+
+ port8: port at 8 {
+ reg = <8>;
+ label = "cpu";
+ ethernet = <&gmac>;
+ phy-mode = "rgmii";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+ };
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic at 34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
+#include "axp209.dtsi"
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+};
+
+&ir0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_rx_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bpi_r1>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ cd-inverted;
+ status = "okay";
+};
+
+&otg_sram {
+ status = "okay";
+};
+
+&pio {
+ usb0_id_detect_pin: usb0_id_detect_pin at 0 {
+ allwinner,pins = "PH4";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb0_vbus_detect_pin: usb0_vbus_detect_pin at 0 {
+ allwinner,pins = "PH5";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb0_vbus_pin_bpi_r1: usb0_vbus_pin at 0 {
+ allwinner,pins = "PB9";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb2_vbus_pin_bpi_r1: usb2_vbus_pin at 0 {
+ allwinner,pins = "PH3";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_cd_pin_bpi_r1: mmc0_cd_pin at 0 {
+ allwinner,pins = "PH1";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ gmac_power_pin_bpi_r1: gmac_power_pin at 0 {
+ allwinner,pins = "PH23";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ led_pins_bpi_r1: led_pins at 0 {
+ allwinner,pins = "PH24";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_ahci_5v {
+ status = "okay";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-dll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_usb0_vbus {
+ pinctrl-0 = <&usb0_vbus_pin_bpi_r1>;
+ gpio = <&pio 1 9 GPIO_ACTIVE_HIGH>; /* PB9 */
+ status = "okay";
+};
+
+®_usb1_vbus {
+ status = "okay";
+};
+
+®_usb2_vbus {
+ pinctrl-0 = <&usb2_vbus_pin_bpi_r1>;
+ gpio = <&pio 7 3 GPIO_ACTIVE_HIGH>; /* PH3 */
+ status = "okay";
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins_a>,
+ <&spi0_cs0_pins_a>,
+ <&spi0_cs1_pins_a>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins_a>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins_b>;
+ status = "okay";
+};
+
+&uart7 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart7_pins_a>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usb_power_supply {
+ status = "okay";
+};
+
+&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>;
+ usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+ usb0_vbus_power-supply = <&usb_power_supply>;
+ usb0_vbus-supply = <®_usb0_vbus>;
+ usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_usb2_vbus>;
+ status = "okay";
+};
--
2.9.3
More information about the U-Boot
mailing list