[U-Boot] [PATCH v7 00/21] imx6: Add Engicam i.CoreM6 QDL support
Jagan Teki
jagannadh.teki at gmail.com
Sun Oct 9 16:45:02 CEST 2016
Hi Stefano,
On Sat, Oct 8, 2016 at 6:00 PM, Jagan Teki <jteki at openedev.com> wrote:
> From: Jagan Teki <jagan at amarulasolutions.com>
>
> This series supports Engicam i.CoreM6 QDL modules on top of u-boot-imx/master
> and test on the respective starter kits as well.
>
> Tested both MMC and NAND boot.
>
> Changes for v7:
> - Add patch to CONFIG_DEFAULT_FDT_FILE to defconfigs
> - Rebase on u-boot-imx/master
>
> Changes for v6:
> - Rebase to u-boot-imx/master
> - Move few SPL configs to defconfigs
>
> Changes for v5:
> - Add NAND support
>
> Changes for v4:
> - Add 'net: Kconfig: Add FEC_MXC entry' patch
> - Updated ENV configs along with comments
> - Restructured configs for more readability
> - Add CONFIG_ENV_OVERWRITE
> - Rename icorem6qdl_defconfig with icorem6qdl_mmc_defconfig
>
> Changes for v3:
> - Remove "v2 01/17 imx: iomux-v3: Fix build error with snvs base" patch
> - Remove 'default n' on Kconfig DEFAULT_FDT_FILE patch
> - Add minimal devicetree support for Engicam i.CoreM6 QDL
> - Add is_mx6dl()
> - Add is_mx6solo()
> - Use is_mx6dq()
> - Add last commit sha1 and header in pull devicetree files from Linux
>
> Changes for v2:
> - Make static to local iomux structure in board file
> - Corrected rowaddr in mx6_ddr3_cfg
> - Used imx_ddr_size
> - Add FEC support and tested the same
> - Add DM_GPIO, DM_MMC support
> - Add pinctrl support
> - Add devicetree support
>
> Jagan Teki (21):
> serial: Kconfig: Add MXC_UART entry
> thermal: Kconfig: Add IMX_THERMAL entry
> config: Move CONFIG_DEFAULT_FDT_FILE to defconfigs
> arm: imx: Add Engicam i.CoreM6 QDL Starter Kit initial support
> net: Kconfig: Add FEC_MXC entry
> imx6: icorem6: Add ENET support
> imx: s/docs\/README.imximage/doc\/README.imximage/g
> arm: dts: Add devicetree for i.MX6DL
> arm: dts: Add devicetree for i.MX6DQL
> arm: dts: imx6dl: Add pinctrl defines
> dt-bindings: clock: imx6qdl: Add clock defines
> arm: imx6q: Add devicetree support for Engicam i.CoreM6 DualLite/Solo
> imx6q: icorem6: Enable pinctrl driver
> engicam: icorem6: Add DM_GPIO, DM_MMC support
> arm: dts: Add devicetree for i.MX6Q
> arm: dts: imx6q: Add pinctrl defines
> arm: imx6q: Add devicetree support for Engicam i.CoreM6 Quad/Dual
> mtd: nand: Kconfig: Add NAND_MXS entry
> imx6: icorem6: Add NAND support
> imx6: icorem6: Enable MTD device support
> imx6: icorem6: Add default mtd nand partition table
All set now, please do apply.
thanks!
--
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.
More information about the U-Boot
mailing list