[U-Boot] [PATCH V3] imx: i.mx6q: add the initial support for LogicPD i.MX6Q SOM
Adam Ford
aford173 at gmail.com
Tue Apr 4 13:49:21 UTC 2017
Logic PD has an i.MX6Q system on module (SOM) with a development kit. The
SOM has a built-in microSD socket, DDR and NAND flash. The development kit
has an SMSC Ethernet PHY, serial debug port and a variety of peripherals.
This have been verified to boot the i.MX6Q version over either SD
on the development kit or NAND built into the SOM.
Signed-off-by: Adam Ford <aford173 at gmail.com>
---
Changes in V3:
- Add OF_CONTROL and device tree
- Switch to DM_I2C
- Switch to DM_ETH
- Switch to DM_MMC
- Switch to DM_PMIC
- Switch to DM_REGULATOR
- Switch to DM_GPIO
- Fix Ethernet reset to play nicely with DM_GPIO and DM_ETH
- Remove more unnecessary code with DM enabled.
Changes in V2:
- Alphabetize the modified Kconfig file
- Clean up README file.
- Elminate fdt_high and initrd_high and add bootm_size
- Changed MTDPARTS_DEFAULT to increase the kernel size to 16MB
- Cleaned up the mx6q_2x_MT41K512M16HA.cfg to include headers,
replace hard-coded addresses with human-readable ones, and
remove dead code
- Updated mx6q_2x_MT41K512M16HA.cfg to use BOOT_OFFSET since SD
and NAND have the same offset
- Removed 'ifdef' references that were always true.
- Removed CPU references that didn't exist.
- And made local variables static
- Add reference to worked used to derrive this code
diff --git a/arch/arm/cpu/armv7/mx6/Kconfig b/arch/arm/cpu/armv7/mx6/Kconfig
index 190e5c6..18241d0 100644
--- a/arch/arm/cpu/armv7/mx6/Kconfig
+++ b/arch/arm/cpu/armv7/mx6/Kconfig
@@ -155,6 +155,20 @@ config TARGET_MX6CUBOXI
select BOARD_LATE_INIT
select SUPPORT_SPL
+config TARGET_MX6LOGICPD
+ bool "Logic PD i.MX6 SOM"
+ select BOARD_EARLY_INIT_F
+ select BOARD_LATE_INIT
+ select DM
+ select DM_ETH
+ select DM_GPIO
+ select DM_I2C
+ select DM_MMC
+ select DM_PMIC
+ select DM_REGULATOR
+ select DM_THERMAL
+ select OF_CONTROL
+
config TARGET_MX6QARM2
bool "mx6qarm2"
@@ -404,6 +418,7 @@ source "board/gateworks/gw_ventana/Kconfig"
source "board/kosagi/novena/Kconfig"
source "board/samtec/vining_2000/Kconfig"
source "board/liebherr/mccmon6/Kconfig"
+source "board/logicpd/imx6/Kconfig"
source "board/seco/Kconfig"
source "board/solidrun/mx6cuboxi/Kconfig"
source "board/technexion/pico-imx6ul/Kconfig"
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 0fbbb9b..a95f2db 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -319,6 +319,7 @@ dtb-$(CONFIG_MX6) += imx6ull-14x14-evk.dtb \
imx6dl-icore-rqs.dtb \
imx6q-icore.dtb \
imx6q-icore-rqs.dtb \
+ imx6q-logicpd.dtb \
imx6sx-sabreauto.dtb \
imx6ul-geam-kit.dtb \
imx6ul-isiot-emmc.dtb \
diff --git a/arch/arm/dts/imx6q-logicpd.dts b/arch/arm/dts/imx6q-logicpd.dts
new file mode 100644
index 0000000..f5ac5d9
--- /dev/null
+++ b/arch/arm/dts/imx6q-logicpd.dts
@@ -0,0 +1,220 @@
+/*
+ * Copyright 2017 Logic PD, Inc.
+ * Based on SabreSD, Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx6qdl-logicpd.dtsi"
+
+/ {
+ model = "Logic PD i.MX6QDL SOM";
+ compatible = "fsl,imx6q";
+
+ leds {
+ compatible = "gpio-leds";
+
+ gen_led0 {
+ label = "cpu0";
+ gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "cpu0";
+ };
+
+ gen_led1 {
+ label = "cpu1";
+ gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "cpu1";
+ };
+
+ gen_led2 {
+ label = "heartbeat";
+ gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ gen_led3 {
+ label = "Always On";
+ gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+ };
+
+ reg_usb_otg_vbus: regulator-otg-vbus at 0 {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usb_h1_vbus: regulator-usbh1vbus at 1 {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_h1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_3v3: regulator-3v3 at 2 {
+ compatible = "regulator-fixed";
+ regulator-name = "reg_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+&usbh1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh1>;
+ vbus-supply = <®_usb_h1_vbus>;
+ status = "okay";
+};
+
+&usbh2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh2>;
+ phy_type = "hsic";
+ disable-over-current;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ disable-over-current;
+ status = "okay";
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rmii";
+ phy-speed = <10>;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ keep-power-in-suspend;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D23__UART3_CTS_B 0x1b0b1
+ MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_EB3__UART3_RTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
+ MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x130b0 /* USB_OTG_PWR_EN */
+ >;
+ };
+
+ pinctrl_usbh1: usbh1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0 /* USB_H1_PWR_EN */
+ >;
+ };
+
+ pinctrl_usbh2: usbh2grp {
+ fsl,pins = <
+ MX6QDL_PAD_RGMII_TXC__USB_H2_DATA 0x13030
+ MX6QDL_PAD_RGMII_TX_CTL__USB_H2_STROBE 0x17030
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
+ MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
+ MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
+ MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
+ MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x1b0b0 /* nINT */
+ MX6QDL_PAD_KEY_ROW1__GPIO4_IO09 0x1b0b0 /* Ethernet Reset */
+ >;
+ };
+
+ pinctrl_gpio_leds: gpioledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x130b0
+ MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x130b0
+ MX6QDL_PAD_EIM_D21__GPIO3_IO21 0x130b0
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x130b0
+ >;
+ };
+};
+
diff --git a/arch/arm/dts/imx6qdl-logicpd.dtsi b/arch/arm/dts/imx6qdl-logicpd.dtsi
new file mode 100644
index 0000000..592ad05
--- /dev/null
+++ b/arch/arm/dts/imx6qdl-logicpd.dtsi
@@ -0,0 +1,418 @@
+/*
+ * Copyright 2016 Logic PD
+ * This file is adapted from imx6qdl-sabresd.dtsi.
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "imx6q.dtsi"
+
+/ {
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ memory {
+ reg = <0x10000000 0x80000000>;
+ };
+};
+
+/* Reroute power feeding the CPU to come from the external PMIC */
+®_arm
+{
+ vin-supply = <&sw1a_reg>;
+};
+
+®_soc
+{
+ vin-supply = <&sw1c_reg>;
+};
+
+&clks {
+ assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
+ <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
+ assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
+ <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ status = "okay";
+ nand-on-flash-bbt;
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ pmic: pfuze100 at 08 {
+ compatible = "fsl,pfuze100";
+ reg = <0x08>;
+
+ regulators {
+ sw1a_reg: sw1ab {
+ regulator-min-microvolt = <725000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-name = "vddcore";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw1c_reg: sw1c {
+ regulator-min-microvolt = <725000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-name = "vddsoc";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "gen_3v3";
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3a_reg: sw3a {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-name = "sw3a_vddr";
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3b_reg: sw3b {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-name = "sw3b_vddr";
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw4_reg: sw4 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "gen_rgmii";
+ };
+
+
+ swbst_reg: swbst {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5150000>;
+ regulator-name = "gen_5v0";
+ };
+
+ snvs_reg: vsnvs {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "gen_vsns";
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vref_reg: vrefddr {
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vgen1_reg: vgen1 {
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "gen_1v5";
+ };
+
+ vgen2_reg: vgen2 {
+ regulator-name = "vgen2";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ vgen3_reg: vgen3 {
+ regulator-name = "gen_vadj_0";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ vgen4_reg: vgen4 {
+ regulator-name = "gen_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ vgen5_reg: vgen5 {
+ regulator-name = "gen_adj_1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen6_reg: vgen6 {
+ regulator-name = "gen_2v5";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-always-on;
+ };
+ };
+ };
+
+ temp_sense0: tmp102 at 4a {
+ compatible = "ti,tmp102";
+ reg = <0x4a>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tempsense>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+ #thermal-sensor-cells = <1>;
+ };
+
+ temp_sense1: tmp102 at 49 {
+ compatible = "ti,tmp102";
+ reg = <0x49>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+ #thermal-sensor-cells = <1>;
+ };
+
+ mfg_eeprom: at24 at 51 {
+ compatible = "atmel,24c64";
+ pagesize = <32>;
+ read-only;
+ reg = <0x51>;
+ };
+
+ user_eeprom: at24 at 52 {
+ compatible = "atmel,24c64";
+ pagesize = <32>;
+ reg = <0x52>;
+ };
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_MCLK__ARM_TRACE_CTL 0x1b0b0
+ MX6QDL_PAD_CSI0_DATA_EN__ARM_TRACE_CLK 0x1b0b0
+ MX6QDL_PAD_CSI0_VSYNC__ARM_TRACE00 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT4__ARM_TRACE01 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT5__ARM_TRACE02 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT6__ARM_TRACE03 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT7__ARM_TRACE04 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT8__ARM_TRACE05 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT9__ARM_TRACE06 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT10__ARM_TRACE07 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT11__ARM_TRACE08 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT12__ARM_TRACE09 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT13__ARM_TRACE10 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT14__ARM_TRACE11 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT15__ARM_TRACE12 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT16__ARM_TRACE13 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT17__ARM_TRACE14 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT18__ARM_TRACE15 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT19__GPIO6_IO05 0x1b0b0
+ MX6QDL_PAD_EIM_LBA__GPIO2_IO27 0x80000000
+ MX6QDL_PAD_EIM_OE__GPIO2_IO25 0x80000000
+ MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x80000000
+ MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x80000000
+ MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x80000000
+ MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x80000000
+ MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x80000000
+ MX6QDL_PAD_EIM_A18__GPIO2_IO20 0x80000000
+ MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x80000000
+ MX6QDL_PAD_EIM_A20__GPIO2_IO18 0x80000000
+ MX6QDL_PAD_EIM_A21__GPIO2_IO17 0x80000000
+ MX6QDL_PAD_EIM_A22__GPIO2_IO16 0x80000000
+ MX6QDL_PAD_EIM_A23__GPIO6_IO06 0x80000000
+ MX6QDL_PAD_EIM_A24__GPIO5_IO04 0x80000000
+ MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x80000000
+ MX6QDL_PAD_EIM_DA0__GPIO3_IO00 0x80000000
+ MX6QDL_PAD_EIM_DA1__GPIO3_IO01 0x80000000
+ MX6QDL_PAD_EIM_DA2__GPIO3_IO02 0x80000000
+ MX6QDL_PAD_EIM_DA3__GPIO3_IO03 0x80000000
+ MX6QDL_PAD_EIM_DA4__GPIO3_IO04 0x80000000
+ MX6QDL_PAD_EIM_DA5__GPIO3_IO05 0x80000000
+ MX6QDL_PAD_EIM_DA6__GPIO3_IO06 0x80000000
+ MX6QDL_PAD_EIM_DA7__GPIO3_IO07 0x80000000
+ MX6QDL_PAD_EIM_DA8__GPIO3_IO08 0x80000000
+ MX6QDL_PAD_EIM_DA9__GPIO3_IO09 0x80000000
+ MX6QDL_PAD_EIM_DA10__GPIO3_IO10 0x80000000
+ MX6QDL_PAD_EIM_DA11__GPIO3_IO11 0x80000000
+ MX6QDL_PAD_EIM_DA12__GPIO3_IO12 0x80000000
+ MX6QDL_PAD_EIM_DA13__GPIO3_IO13 0x80000000
+ MX6QDL_PAD_EIM_DA14__GPIO3_IO14 0x80000000
+ MX6QDL_PAD_EIM_DA15__GPIO3_IO15 0x80000000
+ MX6QDL_PAD_EIM_D16__GPIO3_IO16 0x80000000
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x80000000
+ MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x80000000
+ MX6QDL_PAD_EIM_D21__GPIO3_IO21 0x80000000
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x80000000
+ MX6QDL_PAD_EIM_D26__GPIO3_IO26 0x80000000
+ MX6QDL_PAD_EIM_D27__GPIO3_IO27 0x80000000
+ MX6QDL_PAD_EIM_EB0__GPIO2_IO28 0x80000000
+ MX6QDL_PAD_EIM_EB1__GPIO2_IO29 0x80000000
+ MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x80000000
+ MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0x80000000
+ MX6QDL_PAD_EIM_WAIT__GPIO5_IO00 0x80000000
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x80000000
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x80000000
+ MX6QDL_PAD_GPIO_7__GPIO1_IO07 0x80000000
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x80000000
+ MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x80000000
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x80000000
+ MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x80000000
+ MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x80000000
+ MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x80000000
+ MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x80000000
+ MX6QDL_PAD_KEY_COL1__GPIO4_IO08 0x80000000
+ MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x80000000
+ MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x80000000
+ MX6QDL_PAD_RGMII_TD0__GPIO6_IO20 0x80000000
+ MX6QDL_PAD_RGMII_TD1__GPIO6_IO21 0x80000000
+ MX6QDL_PAD_RGMII_TD2__GPIO6_IO22 0x80000000
+ MX6QDL_PAD_RGMII_TD3__GPIO6_IO23 0x80000000
+ MX6QDL_PAD_RGMII_RD0__GPIO6_IO25 0x80000000
+ MX6QDL_PAD_RGMII_RD1__GPIO6_IO27 0x80000000
+ MX6QDL_PAD_RGMII_RD2__GPIO6_IO28 0x80000000
+ MX6QDL_PAD_RGMII_RD3__GPIO6_IO29 0x80000000
+ MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x80000000
+ MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x80000000
+ >;
+ };
+
+ pinctrl_gpmi_nand: gpminandgrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CLE__NAND_CLE 0x0b0b1
+ MX6QDL_PAD_NANDF_ALE__NAND_ALE 0x0b0b1
+ MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0x0b0b1
+ MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0x0b000
+ MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0x0b0b1
+ MX6QDL_PAD_SD4_CMD__NAND_RE_B 0x0b0b1
+ MX6QDL_PAD_SD4_CLK__NAND_WE_B 0x0b0b1
+ MX6QDL_PAD_NANDF_D0__NAND_DATA00 0x0b0b1
+ MX6QDL_PAD_NANDF_D1__NAND_DATA01 0x0b0b1
+ MX6QDL_PAD_NANDF_D2__NAND_DATA02 0x0b0b1
+ MX6QDL_PAD_NANDF_D3__NAND_DATA03 0x0b0b1
+ MX6QDL_PAD_NANDF_D4__NAND_DATA04 0x0b0b1
+ MX6QDL_PAD_NANDF_D5__NAND_DATA05 0x0b0b1
+ MX6QDL_PAD_NANDF_D6__NAND_DATA06 0x0b0b1
+ MX6QDL_PAD_NANDF_D7__NAND_DATA07 0x0b0b1
+ >;
+ };
+
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1
+ MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b0b1
+ MX6QDL_PAD_SD4_DAT5__UART2_RTS_B 0x1b0b1
+ MX6QDL_PAD_SD4_DAT6__UART2_CTS_B 0x1b0b1
+ MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17071
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10071
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17071
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17071
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17071
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17071
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+ MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0x1f0b0 /* WL_IRQ */
+ MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x1f0b0 /* WLAN_EN */
+ MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x1f0b0 /* BT_EN */
+ >;
+ };
+
+ pinctrl_tempsense: tempsensegrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x1b0b0 /* Temp Sense Alert */
+ >;
+ };
+};
+
+&snvs_poweroff {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio6 16 GPIO_ACTIVE_HIGH>;
+ keep-power-in-suspend;
+ enable-sdio-wakeup;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ non-removable;
+ keep-power-in-suspend;
+ enable-sdio-wakeup;
+ vmmc-supply = <&sw2_reg>;
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ wlcore: wlcore at 0 {
+ compatible = "ti,wl1837";
+ reg = <2>;
+ interrupt-parent = <&gpio7>;
+ interrupts = <1 GPIO_ACTIVE_HIGH>;
+ };
+};
+
diff --git a/board/logicpd/imx6/Kconfig b/board/logicpd/imx6/Kconfig
new file mode 100644
index 0000000..f5e2f58
--- /dev/null
+++ b/board/logicpd/imx6/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_MX6LOGICPD
+
+config SYS_BOARD
+ default "imx6"
+
+config SYS_VENDOR
+ default "logicpd"
+
+config SYS_CONFIG_NAME
+ default "imx6_logic"
+
+endif
diff --git a/board/logicpd/imx6/MAINTAINERS b/board/logicpd/imx6/MAINTAINERS
new file mode 100644
index 0000000..5db7d2c
--- /dev/null
+++ b/board/logicpd/imx6/MAINTAINERS
@@ -0,0 +1,6 @@
+MX6LOGICPD BOARD
+M: Adam Ford <aford173 at gmail.com>
+S: Maintained
+F: board/logicpd/imx6/
+F: include/configs/imx6_logic.h
+F: configs/imx6q_logic_defconfig
diff --git a/board/logicpd/imx6/Makefile b/board/logicpd/imx6/Makefile
new file mode 100644
index 0000000..337df92
--- /dev/null
+++ b/board/logicpd/imx6/Makefile
@@ -0,0 +1,10 @@
+#
+# Copyright (C) 2007, Guennadi Liakhovetski <lg at denx.de>
+#
+# (C) Copyright 2011 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := imx6logic.o
+
diff --git a/board/logicpd/imx6/README b/board/logicpd/imx6/README
new file mode 100644
index 0000000..7c9b6bd
--- /dev/null
+++ b/board/logicpd/imx6/README
@@ -0,0 +1,37 @@
+U-Boot for LogicPD i.MX6 Development Kit
+----------------------------------------
+
+This file contains information for the port of U-Boot to the Logic PD Development kit.
+
+Logic PD has an i.MX6 System On Module (SOM) and a correspondong development
+board. SOM has a built-in microSD socket, DDR and NAND flash. The development kit has
+an SMSC Ethernet PHY, serial debug port and a variety of peripherals.
+
+On the intial release, the SOM came with an i.MX6D and i.MX6Q.
+
+For more details about Logic PD i.MX6 Development kit, visit:
+https://www.logicpd.com/
+
+Building U-Boot for Logic PD Development Kit
+--------------------------------------------
+To build U-Boot for the Dual and Quad variants:
+
+ make imx6q_logic_defconfig
+ make u-boot.imx ARCH=arm CROSS_COMPILE=arm-linux-
+
+
+Flashing U-Boot into the SD card
+--------------------------------
+
+See README.imximage for details on booting from SD
+
+Flashing U-Boot into NAND
+-------------------------
+Once in Linux with MTD support for the NAND on /dev/mtd0, program U-Boot with the following:
+with:
+
+ kobs-ng init -v -x u-boot.imx
+
+Additional Support Documentation can be found at:
+https://support.logicpd.com/
+
diff --git a/board/logicpd/imx6/imx6logic.c b/board/logicpd/imx6/imx6logic.c
new file mode 100644
index 0000000..fd8f330
--- /dev/null
+++ b/board/logicpd/imx6/imx6logic.c
@@ -0,0 +1,190 @@
+/*
+ * Copyright (C) 2017 Logic PD, Inc.
+ *
+ * Author: Adam Ford <aford173 at gmail.com>
+ *
+ * Based on SabreSD by Fabio Estevam <fabio.estevam at nxp.com>
+ * and updates by Jagan Teki <jagan at amarulasolutions.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <asm/io.h>
+#include <asm/gpio.h>
+#include <linux/sizes.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mxc_hdmi.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/imx-common/boot_mode.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <netdev.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+#define NAND_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
+int dram_init(void)
+{
+ gd->ram_size = imx_ddr_size();
+ return 0;
+}
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+ MX6_PAD_SD3_DAT7__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_SD3_DAT6__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const uart2_pads[] = {
+ MX6_PAD_SD4_DAT4__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_SD4_DAT5__UART2_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_SD4_DAT6__UART2_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_SD4_DAT7__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const uart3_pads[] = {
+ MX6_PAD_EIM_D23__UART3_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_EIM_D24__UART3_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_EIM_D25__UART3_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_EIM_EB3__UART3_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static void fixup_enet_clock(void)
+{
+ struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
+ struct gpio_desc nint;
+ struct gpio_desc reset;
+ int ret;
+
+ /* Set GPIO_16 as ENET_REF_CLK_OUT */
+ setbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_ENET_CLK_SEL_MASK);
+
+ /* Request GPIO Pins to reset Ethernet with new clock */
+ ret = dm_gpio_lookup_name("GPIO4_7", &nint);
+ if (ret) {
+ printf("Unable to lookup GPIO4_7\n");
+ return;
+ }
+
+ ret = dm_gpio_request(&nint, "eth0_nInt");
+ if (ret) {
+ printf("Unable to request eth0_nInt\n");
+ return;
+ }
+ /* Ensure nINT is input or PHY won't startup */
+ dm_gpio_set_dir_flags(&nint, GPIOD_IS_IN);
+
+ ret = dm_gpio_lookup_name("GPIO4_9", &reset);
+ if (ret) {
+ printf("Unable to lookup GPIO4_9\n");
+ return;
+ }
+
+ ret = dm_gpio_request(&reset, "eth0_reset");
+ if (ret) {
+ printf("Unable to request eth0_reset\n");
+ return;
+ }
+
+ /* Reset LAN8710A PHY */
+ dm_gpio_set_dir_flags(&reset, GPIOD_IS_OUT);
+ dm_gpio_set_value(&reset, 0);
+ udelay(150);
+ dm_gpio_set_value(&reset, 1);
+ mdelay(50);
+}
+
+static void setup_iomux_uart(void)
+{
+ imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+ imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
+ imx_iomux_v3_setup_multiple_pads(uart3_pads, ARRAY_SIZE(uart3_pads));
+}
+
+static iomux_v3_cfg_t const nand_pads[] = {
+ MX6_PAD_NANDF_CS0__NAND_CE0_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX6_PAD_NANDF_ALE__NAND_ALE | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX6_PAD_NANDF_CLE__NAND_CLE | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX6_PAD_NANDF_WP_B__NAND_WP_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX6_PAD_NANDF_RB0__NAND_READY_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX6_PAD_NANDF_D0__NAND_DATA00 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX6_PAD_NANDF_D1__NAND_DATA01 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX6_PAD_NANDF_D2__NAND_DATA02 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX6_PAD_NANDF_D3__NAND_DATA03 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX6_PAD_NANDF_D4__NAND_DATA04 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX6_PAD_NANDF_D5__NAND_DATA05 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX6_PAD_NANDF_D6__NAND_DATA06 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX6_PAD_NANDF_D7__NAND_DATA07 | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX6_PAD_SD4_CLK__NAND_WE_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
+ MX6_PAD_SD4_CMD__NAND_RE_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
+};
+
+static void setup_nand_pins(void)
+{
+ imx_iomux_v3_setup_multiple_pads(nand_pads, ARRAY_SIZE(nand_pads));
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+ fixup_enet_clock();
+ if (phydev->drv->config)
+ phydev->drv->config(phydev);
+
+ return 0;
+}
+
+/*
+ * Do not overwrite the console
+ * Use always serial for U-Boot console
+ */
+int overwrite_console(void)
+{
+ return 1;
+}
+
+int board_early_init_f(void)
+{
+ setup_iomux_uart();
+ setup_nand_pins();
+ return 0;
+}
+
+int board_init(void)
+{
+ /* address of boot parameters */
+ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+ enable_fec_anatop_clock(0, ENET_50MHZ);
+ return 0;
+}
+
+static const struct boot_mode board_boot_modes[] = {
+ /* 4 bit bus width */
+ /* 4 bit bus width */
+ {"sd1", MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
+ {"sd2", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
+ {NULL, 0},
+};
+
+int board_late_init(void)
+{
+ add_board_boot_modes(board_boot_modes);
+ setenv("board_name", "imx6logic");
+
+ if (is_mx6dq()) {
+ setenv("board_rev", "MX6DQ");
+ setenv("fdt_file", "imx6q-logicpd.dtb");
+ }
+ return 0;
+}
diff --git a/board/logicpd/imx6/mx6q_2x_MT41K512M16HA.cfg b/board/logicpd/imx6/mx6q_2x_MT41K512M16HA.cfg
new file mode 100644
index 0000000..b206548
--- /dev/null
+++ b/board/logicpd/imx6/mx6q_2x_MT41K512M16HA.cfg
@@ -0,0 +1,112 @@
+/*
+ * Copyright (C) 2017 Logic PD, Inc.
+ * Adam Ford <aford173 at gmail.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ * Refer doc/README.imximage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+#include <asm/imx-common/imximage.cfg>
+
+/* image version */
+IMAGE_VERSION 2
+
+BOOT_OFFSET FLASH_OFFSET_STANDARD
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type Address Value
+ *
+ * where:
+ * Addr-type register length (1,2 or 4 bytes)
+ * Address absolute address of the register
+ * value value to be stored in the register
+ */
+
+#define __ASSEMBLY__
+#include <config.h>
+#include "asm/arch-mx6/mx6-ddr.h"
+#include "asm/arch-mx6/iomux.h"
+#include "asm/arch-mx6/crm_regs.h"
+
+DATA 4, MX6_IOM_GRP_DDR_TYPE, 0x000C0000
+DATA 4, MX6_IOM_GRP_DDRPKE, 0x00000000
+DATA 4, MX6_IOM_DRAM_SDCLK_0, 0x00000030
+DATA 4, MX6_IOM_DRAM_SDCLK_1, 0x00000030
+DATA 4, MX6_IOM_DRAM_CAS, 0x00000030
+DATA 4, MX6_IOM_DRAM_RAS, 0x00000030
+DATA 4, MX6_IOM_GRP_ADDDS, 0x00000030
+DATA 4, MX6_IOM_DRAM_RESET, 0x00000030
+DATA 4, MX6_IOM_DRAM_SDBA2, 0x00000000
+DATA 4, MX6_IOM_DRAM_SDODT0, 0x00000030
+DATA 4, MX6_IOM_DRAM_SDODT1, 0x00000030
+DATA 4, MX6_IOM_GRP_CTLDS, 0x00000030
+DATA 4, MX6_IOM_DDRMODE_CTL, 0x00020000
+DATA 4, MX6_IOM_DRAM_SDQS0, 0x00000030
+DATA 4, MX6_IOM_DRAM_SDQS1, 0x00000030
+DATA 4, MX6_IOM_DRAM_SDQS2, 0x00000030
+DATA 4, MX6_IOM_DRAM_SDQS3, 0x00000030
+DATA 4, MX6_IOM_GRP_DDRMODE, 0x00020000
+DATA 4, MX6_IOM_GRP_B0DS, 0x00000030
+DATA 4, MX6_IOM_GRP_B1DS, 0x00000030
+DATA 4, MX6_IOM_GRP_B2DS, 0x00000030
+DATA 4, MX6_IOM_GRP_B3DS, 0x00000030
+DATA 4, MX6_IOM_DRAM_DQM0, 0x00000030
+DATA 4, MX6_IOM_DRAM_DQM1, 0x00000030
+DATA 4, MX6_IOM_DRAM_DQM2, 0x00000030
+DATA 4, MX6_IOM_DRAM_DQM3, 0x00000030
+DATA 4, MX6_MMDC_P0_MDSCR, 0x00008000
+DATA 4, MX6_MMDC_P0_MPZQHWCTRL, 0xA1390003
+DATA 4, MX6_MMDC_P0_MPWLDECTRL0, 0x002D003A
+DATA 4, MX6_MMDC_P0_MPWLDECTRL1, 0x0038002B
+DATA 4, MX6_MMDC_P0_MPDGCTRL0, 0x03340338
+DATA 4, MX6_MMDC_P0_MPDGCTRL1, 0x0334032C
+DATA 4, MX6_MMDC_P0_MPRDDLCTL, 0x4036383C
+DATA 4, MX6_MMDC_P0_MPWRDLCTL, 0x2E384038
+DATA 4, MX6_MMDC_P0_MPRDDQBY0DL, 0x33333333
+DATA 4, MX6_MMDC_P0_MPRDDQBY1DL, 0x33333333
+DATA 4, MX6_MMDC_P0_MPRDDQBY2DL, 0x33333333
+DATA 4, MX6_MMDC_P0_MPRDDQBY3DL, 0x33333333
+DATA 4, MX6_MMDC_P0_MPMUR0, 0x00000800
+DATA 4, MX6_MMDC_P0_MDPDC, 0x00020036
+DATA 4, MX6_MMDC_P0_MDOTC, 0x09444040
+DATA 4, MX6_MMDC_P0_MDCFG0, 0xB8BE7955
+DATA 4, MX6_MMDC_P0_MDCFG1, 0xFF328F64
+DATA 4, MX6_MMDC_P0_MDCFG2, 0x01FF00DB
+DATA 4, MX6_MMDC_P0_MDMISC, 0x00011740
+DATA 4, MX6_MMDC_P0_MDSCR, 0x00008000
+DATA 4, MX6_MMDC_P0_MDRWD, 0x000026D2
+DATA 4, MX6_MMDC_P0_MDOR, 0x00BE1023
+DATA 4, MX6_MMDC_P0_MDASP, 0x00000047
+DATA 4, MX6_MMDC_P0_MDCTL, 0x85190000
+DATA 4, MX6_MMDC_P0_MDSCR, 0x00888032
+DATA 4, MX6_MMDC_P0_MDSCR, 0x00008033
+DATA 4, MX6_MMDC_P0_MDSCR, 0x00008031
+DATA 4, MX6_MMDC_P0_MDSCR, 0x19408030
+DATA 4, MX6_MMDC_P0_MDSCR, 0x04008040
+DATA 4, MX6_MMDC_P0_MDREF, 0x00007800
+DATA 4, MX6_MMDC_P0_MPODTCTRL, 0x00000007
+DATA 4, MX6_MMDC_P0_MDPDC, 0x00025576
+DATA 4, MX6_MMDC_P0_MAPSR, 0x00011006
+DATA 4, MX6_MMDC_P0_MDSCR, 0x00000000
+
+/* set the default clock gate to save power */
+DATA 4, CCM_CCGR0, 0x00C03F3F
+DATA 4, CCM_CCGR1, 0x0030FC03
+DATA 4, CCM_CCGR2, 0x0FFFC000
+DATA 4, CCM_CCGR3, 0x3FF00000
+DATA 4, CCM_CCGR4, 0xFFFFF300
+DATA 4, CCM_CCGR5, 0x0F0000F3
+DATA 4, CCM_CCGR6, 0x00000FFF
+
+/* enable AXI cache for VDOA/VPU/IPU */
+DATA 4 MX6_IOMUXC_GPR4 0xF00000CF
+/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
+DATA 4 MX6_IOMUXC_GPR6 0x007F007F
+DATA 4 MX6_IOMUXC_GPR7 0x007F007F
diff --git a/configs/imx6q_logic_defconfig b/configs/imx6q_logic_defconfig
new file mode 100644
index 0000000..828adde
--- /dev/null
+++ b/configs/imx6q_logic_defconfig
@@ -0,0 +1,39 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_TARGET_MX6LOGICPD=y
+CONFIG_DEFAULT_DEVICE_TREE="imx6q-logicpd"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/logicpd/imx6/mx6q_2x_MT41K512M16HA.cfg,MX6Q"
+CONFIG_BOOTDELAY=3
+# CONFIG_CONSOLE_MUX is not set
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
+CONFIG_HUSH_PARSER=y
+CONFIG_SYS_PROMPT="i.MX6 Logic # "
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_NAND=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_NAND_MXS=y
+CONFIG_DISPLAY_CPUINFO=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_OF_LIBFDT=y
+# CONFIG_BLK is not set
+# CONFIG_DM_MMC_OPS is not set
+CONFIG_DM_PMIC_PFUZE100=y
+CONFIG_SYS_I2C_MXC=y
+CONFIG_FEC_MXC=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
+
diff --git a/include/configs/imx6_logic.h b/include/configs/imx6_logic.h
new file mode 100644
index 0000000..7c23ff4
--- /dev/null
+++ b/include/configs/imx6_logic.h
@@ -0,0 +1,186 @@
+/*
+ * Copyright (C) 2017 Logic PD, Inc.
+ *
+ * Configuration settings for the LogicPD i.MX6 SOM.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __IMX6LOGIC_CONFIG_H
+#define __IMX6LOGIC_CONFIG_H
+
+#define CONFIG_MXC_UART_BASE UART1_BASE
+#define CONSOLE_DEV "ttymxc0"
+
+#include <config_distro_defaults.h>
+#include "mx6_common.h"
+
+#define CONFIG_IMX_THERMAL
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M)
+
+#define CONFIG_MXC_UART
+
+/* MMC Configs */
+#define CONFIG_SYS_FSL_ESDHC_ADDR 0
+#define CONFIG_SYS_FSL_USDHC_NUM 2
+#define CONFIG_MMCROOT "/dev/mmcblk1p2" /* Dev kit SD card */
+
+/* Ethernet Configs */
+#define CONFIG_MII
+#define IMX_FEC_BASE ENET_BASE_ADDR
+#define CONFIG_FEC_XCV_TYPE RMII
+#define CONFIG_ETHPRIME "FEC"
+#define CONFIG_FEC_MXC_PHYADDR 0
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_SMSC
+
+/* Command definition */
+#define CONFIG_CMD_BMODE
+
+#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "script=boot.scr\0" \
+ "image=zImage\0" \
+ "bootm_size=0x10000000\0" \
+ "fdt_addr_r=0x18000000\0" \
+ "fdt_addr=0x18000000\0" \
+ "ramdisk_addr_r=0x13000000\0" \
+ "ramdiskaddr=0x13000000\0" \
+ "kernel_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
+ "ramdisk_file=rootfs.cpio.uboot\0" \
+ "boot_fdt=try\0" \
+ "ip_dyn=yes\0" \
+ "console=" CONSOLE_DEV "\0" \
+ "mmcdev=1\0" \
+ "mmcpart=1\0" \
+ "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
+ "nandroot=ubi0:rootfs rootfstype=ubifs\0" \
+ "mmcargs=setenv bootargs console=${console},${baudrate}" \
+ " root=${mmcroot} ${mtdparts}\0" \
+ "nandargs=setenv bootargs console=${console},${baudrate}" \
+ " ubi.mtd=fs root=${nandroot} ${mtdparts}\0" \
+ "ramargs=setenv bootargs console=${console},${baudrate}" \
+ " root=/dev/ram rw ${mtdparts}\0" \
+ "loadbootscript=" \
+ "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+ "bootscript=echo Running bootscript from mmc ...;" \
+ " source\0" \
+ "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image};" \
+ " setenv kernelsize ${filesize}\0" \
+ "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+ "loadramdisk=fatload mmc ${mmcdev}:${mmcpart} ${ramdiskaddr} ${ramdisk_file};" \
+ " setenv ramdisksize ${filesize}\0" \
+ "mmcboot=echo Booting from mmc...; run mmcargs; run loadimage;" \
+ " run loadfdt; bootz ${loadaddr} - ${fdt_addr}\0" \
+ "mmcramboot=run ramargs; run loadimage;" \
+ " run loadfdt; run loadramdisk;" \
+ " bootz ${loadaddr} ${ramdiskaddr} ${fdt_addr}\0" \
+ "nandboot=echo Booting from nand ...; " \
+ " run nandargs;" \
+ " nand read ${loadaddr} kernel ${kernelsize};" \
+ " nand read ${fdt_addr} dtb;" \
+ " bootz ${loadaddr} - ${fdt_addr}\0" \
+ "nandramboot=echo Booting RAMdisk from nand ...; " \
+ " nand read ${ramdiskaddr} fs ${ramdisksize};" \
+ " nand read ${loadaddr} kernel ${kernelsize};" \
+ " nand read ${fdt_addr} dtb;" \
+ " run ramargs;" \
+ " bootz ${loadaddr} ${ramdiskaddr} ${fdt_addr}\0" \
+ "netargs=setenv bootargs console=${console},${baudrate} " \
+ "root=/dev/nfs" \
+ " ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+ "netboot=echo Booting from net ...; " \
+ "run netargs; " \
+ "if test ${ip_dyn} = yes; then " \
+ "setenv get_cmd dhcp; " \
+ "else " \
+ "setenv get_cmd tftp; " \
+ "fi; " \
+ "${get_cmd} ${image}; " \
+ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+ "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "if test ${boot_fdt} = try; then " \
+ "bootz; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi; " \
+ "fi; " \
+ "else " \
+ "bootz; " \
+ "fi;\0" \
+ "autoboot=mmc dev ${mmcdev};" \
+ "if mmc rescan; then " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
+ "else " \
+ "if run loadimage; then " \
+ "run mmcboot; " \
+ "else run netboot; " \
+ "fi; " \
+ "fi; " \
+ "else run netboot; fi"
+#define CONFIG_BOOTCOMMAND \
+ "run autoboot"
+
+#define CONFIG_ARP_TIMEOUT 200UL
+
+#define CONFIG_SYS_MEMTEST_START 0x10000000
+#define CONFIG_SYS_MEMTEST_END 0x10010000
+#define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000
+
+#define CONFIG_STACKSIZE (128 * 1024)
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS 1
+#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* Environment organization */
+#define CONFIG_ENV_SIZE (8 * 1024)
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET 0x400000
+#define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
+
+/* NAND flash command */
+
+#define CONFIG_CMD_NAND_TRIMFFS
+
+/* NAND stuff */
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_BASE 0x40000000
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x200000
+
+/* MTD device */
+# define CONFIG_MTD_DEVICE
+# define CONFIG_CMD_MTDPARTS
+# define CONFIG_MTD_PARTITIONS
+# define MTDIDS_DEFAULT "nand0=gpmi-nand"
+# define MTDPARTS_DEFAULT "mtdparts=gpmi-nand:4m(uboot)," \
+ "1m(env),16m(kernel),1m(dtb),-(fs)"
+
+/* DMA stuff, needed for GPMI/MXS NAND support */
+#define CONFIG_APBH_DMA
+#define CONFIG_APBH_DMA_BURST
+#define CONFIG_APBH_DMA_BURST8
+
+/* PMIC */
+#define CONFIG_DM_REGULATOR_PFUZE100
+#define CONFIG_CMD_PMIC
+#define CONFIG_CMD_REGULATOR
+
+#endif /* __IMX6LOGIC_CONFIG_H */
--
2.7.4
More information about the U-Boot
mailing list