[U-Boot] [PATCH v4 19/35] ARM: i.MX6: sabresd: Enable DM_ETH

[Jagan Teki]

From: Jagan Teki <jagan at amarulasolutions.com>

Enable DM_ETH for dt supported sabresd config boards:
- imx6q_sabresd_defconfig
- imx6qp_sabresd_defconfig

Cc: Stefano Babic <sbabic at denx.de>
Cc: Fabio Estevam <fabio.estevam at nxp.com>
Cc: Michael Trimarchi <michael at amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan at amarulasolutions.com>
---
Changes for v4, v3, v2:
- none

 board/freescale/mx6sabresd/mx6sabresd.c | 6 ++++++
 configs/imx6q_sabresd_spl_defconfig     | 1 +
 configs/imx6qp_sabresd_spl_defconfig    | 1 +
 3 files changed, 8 insertions(+)

diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c
index a143dbb..10bc7c6 100644
--- a/board/freescale/mx6sabresd/mx6sabresd.c
+++ b/board/freescale/mx6sabresd/mx6sabresd.c
@@ -70,6 +70,7 @@ static iomux_v3_cfg_t const uart1_pads[] = {
 	MX6_PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
 };
 
+#ifndef CONFIG_OF_CONTROL
 static iomux_v3_cfg_t const enet_pads[] = {
 	MX6_PAD_ENET_MDIO__ENET_MDIO		| MUX_PAD_CTRL(ENET_PAD_CTRL),
 	MX6_PAD_ENET_MDC__ENET_MDC		| MUX_PAD_CTRL(ENET_PAD_CTRL),
@@ -100,6 +101,7 @@ static void setup_iomux_enet(void)
 	gpio_set_value(IMX_GPIO_NR(1, 25), 1);
 	udelay(100);
 }
+#endif
 
 static iomux_v3_cfg_t const usdhc2_pads[] = {
 	MX6_PAD_SD2_CLK__SD2_CLK	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
@@ -222,6 +224,7 @@ static void setup_spi(void)
 	imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
 }
 
+#ifndef CONFIG_OF_CONTROL
 iomux_v3_cfg_t const pcie_pads[] = {
 	MX6_PAD_EIM_D19__GPIO3_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL),	/* POWER */
 	MX6_PAD_GPIO_17__GPIO7_IO12 | MUX_PAD_CTRL(NO_PAD_CTRL),	/* RESET */
@@ -231,6 +234,7 @@ static void setup_pcie(void)
 {
 	imx_iomux_v3_setup_multiple_pads(pcie_pads, ARRAY_SIZE(pcie_pads));
 }
+#endif
 
 iomux_v3_cfg_t const di0_pads[] = {
 	MX6_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK,	/* DISP0_CLK */
@@ -507,6 +511,7 @@ int overwrite_console(void)
 	return 1;
 }
 
+#ifndef CONFIG_OF_CONTROL
 int board_eth_init(bd_t *bis)
 {
 	setup_iomux_enet();
@@ -514,6 +519,7 @@ int board_eth_init(bd_t *bis)
 
 	return cpu_eth_init(bis);
 }
+#endif
 
 #if defined(CONFIG_USB_EHCI_MX6) && !defined(CONFIG_DM_USB)
 #define USB_OTHERREGS_OFFSET	0x800
diff --git a/configs/imx6q_sabresd_spl_defconfig b/configs/imx6q_sabresd_spl_defconfig
index 377a489..8c7baee 100644
--- a/configs/imx6q_sabresd_spl_defconfig
+++ b/configs/imx6q_sabresd_spl_defconfig
@@ -52,6 +52,7 @@ CONFIG_G_DNL_PRODUCT_NUM=0xa4a5
 # CONFIG_VIDEO_SW_CURSOR is not set
 CONFIG_OF_LIBFDT=y
 CONFIG_OF_CONTROL=y
+CONFIG_DM_ETH=y
 CONFIG_DM_I2C=y
 CONFIG_DM_GPIO=y
 CONFIG_DM_MMC=y
diff --git a/configs/imx6qp_sabresd_spl_defconfig b/configs/imx6qp_sabresd_spl_defconfig
index 13c2288..7568329 100644
--- a/configs/imx6qp_sabresd_spl_defconfig
+++ b/configs/imx6qp_sabresd_spl_defconfig
@@ -52,6 +52,7 @@ CONFIG_G_DNL_PRODUCT_NUM=0xa4a5
 # CONFIG_VIDEO_SW_CURSOR is not set
 CONFIG_OF_LIBFDT=y
 CONFIG_OF_CONTROL=y
+CONFIG_DM_ETH=y
 CONFIG_DM_I2C=y
 CONFIG_DM_GPIO=y
 CONFIG_DM_MMC=y
-- 
1.9.1