[U-Boot] [PATCH v4 17/19] arm: socfpga: Add config and defconfig for Arria 10
Ley Foon Tan
lftan.linux at gmail.com
Mon Apr 10 07:40:03 UTC 2017
On Fri, Apr 7, 2017 at 10:17 PM, Dinh Nguyen <dinh.linux at gmail.com> wrote:
> On Wed, Apr 5, 2017 at 4:32 AM, Ley Foon Tan <ley.foon.tan at intel.com> wrote:
>> Add config and defconfig for the Arria10 and update socfpga_common.h.
>>
>> Signed-off-by: Tien Fong Chee <tien.fong.chee at intel.com>
>> Signed-off-by: Ley Foon Tan <ley.foon.tan at intel.com>
>> ---
>> configs/socfpga_arria10_defconfig | 28 ++++++++++++++
>> include/configs/socfpga_arria10_socdk.h | 66 +++++++++++++++++++++++++++++++++
>> include/configs/socfpga_common.h | 28 +++++++++++---
>> 3 files changed, 117 insertions(+), 5 deletions(-)
>> create mode 100644 configs/socfpga_arria10_defconfig
>> create mode 100644 include/configs/socfpga_arria10_socdk.h
>>
>
> [snip]
>
>> +
>> +/* Memory configurations */
>> +#define PHYS_SDRAM_1_SIZE 0x80000000
>
> For the HPS side, there's only 1GB on the devkit right?
Yes, will change to 1GB.
>
>> +
>> +/* Ethernet on SoC (EMAC) */
>> +#if defined(CONFIG_CMD_NET)
>> +#define CONFIG_PHY_MICREL
>> +#define CONFIG_PHY_MICREL_KSZ9031
>> +#endif
>> +
>> +/*
>> + * U-Boot environment configurations
>> + */
>> +#define CONFIG_ENV_IS_IN_MMC
>> +
>> +/*
>> + * arguments passed to the bootz command. The value of
>> + * CONFIG_BOOTARGS goes into the environment value "bootargs".
>> + * Do note the value will overide also the chosen node in FDT blob.
>> + */
>> +#define CONFIG_BOOTARGS "console=ttyS0," __stringify(CONFIG_BAUDRATE)
>> +
>> +/*
>> + * Serial / UART configurations
>> + */
>> +#define CONFIG_SYS_NS16550_MEM32
>> +#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600, 115200}
>> +
>> +/*
>> + * L4 OSC1 Timer 0
>> + */
>> +/* reload value when timer count to zero */
>> +#define TIMER_LOAD_VAL 0xFFFFFFFF
>> +
>> +/*
>> + * Flash configurations
>> + */
>> +#define CONFIG_SYS_MAX_FLASH_BANKS 1
>> +
>> +/* The rest of the configuration is shared */
>> +#include <configs/socfpga_common.h>
>> +
>> +#endif /* __CONFIG_SOCFGPA_ARRIA10_H__ */
>> diff --git a/include/configs/socfpga_common.h b/include/configs/socfpga_common.h
>> index f93cd2e..85f8d62 100644
>> --- a/include/configs/socfpga_common.h
>> +++ b/include/configs/socfpga_common.h
>> @@ -32,9 +32,13 @@
>> #define CONFIG_SYS_MALLOC_LEN (64 * 1024 * 1024)
>> #define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_1
>> #define CONFIG_SYS_MEMTEST_END PHYS_SDRAM_1_SIZE
>> -
>> +#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
>> #define CONFIG_SYS_INIT_RAM_ADDR 0xFFFF0000
>> #define CONFIG_SYS_INIT_RAM_SIZE 0x10000
>> +#elif defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
>> +#define CONFIG_SYS_INIT_RAM_ADDR 0xFFE00000
>> +#define CONFIG_SYS_INIT_RAM_SIZE 0x40000 /* 256KB */
>> +#endif
>> #define CONFIG_SYS_INIT_SP_OFFSET \
>> (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
>> #define CONFIG_SYS_INIT_SP_ADDR \
>> @@ -65,8 +69,10 @@
>> #define CONFIG_SYS_HOSTNAME CONFIG_SYS_BOARD
>> #endif
>>
>> +#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
>> #define CONFIG_CMD_PXE
>> #define CONFIG_MENU
>> +#endif
>
> Why doesn't A10 support CMD_PXE and MENU?
There was compilation error in A10 previously when enable PXE.
I found it is due to missing CONFIG_CMD_DHCP. So, I will remove _GEN5
switch here.
>
>>
>> /*
>> * Cache
>> @@ -101,13 +107,14 @@
>> /*
>> * FPGA Driver
>> */
>> +#ifdef CONFIG_TARGET_SOCFPGA_GEN5
>> #ifdef CONFIG_CMD_FPGA
>> #define CONFIG_FPGA
>> #define CONFIG_FPGA_ALTERA
>> #define CONFIG_FPGA_SOCFPGA
>> #define CONFIG_FPGA_COUNT 1
>> #endif
>> -
>> +#endif
>
> Wouldn't you also need to include these for the A10?
This patchset doesn't include FPGA driver. So, disable for A10 as for
now. We will enable this in coming upstream.
>
>> /*
>> * L4 OSC1 Timer 0
>> */
>> @@ -207,11 +214,14 @@ unsigned int cm_get_qspi_controller_clk_hz(void);
>> */
>> #define CONFIG_SYS_NS16550_SERIAL
>> #define CONFIG_SYS_NS16550_REG_SIZE -4
>> -#define CONFIG_SYS_NS16550_COM1 SOCFPGA_UART0_ADDRESS
>> #ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET
>> #define CONFIG_SYS_NS16550_CLK 1000000
>> -#else
>> +#elif defined(CONFIG_TARGET_SOCFPGA_GEN5)
>> +#define CONFIG_SYS_NS16550_COM1 SOCFPGA_UART0_ADDRESS
>> #define CONFIG_SYS_NS16550_CLK 100000000
>> +#elif defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
>> +#define CONFIG_SYS_NS16550_COM1 SOCFPGA_UART1_ADDRESS
>> +#define CONFIG_SYS_NS16550_CLK 50000000
>> #endif
>> #define CONFIG_CONS_INDEX 1
>>
>> @@ -298,7 +308,10 @@ unsigned int cm_get_qspi_controller_clk_hz(void);
>> */
>> #define CONFIG_SPL_FRAMEWORK
>> #define CONFIG_SPL_TEXT_BASE CONFIG_SYS_INIT_RAM_ADDR
>> -#define CONFIG_SPL_MAX_SIZE (64 * 1024)
>> +#define CONFIG_SPL_MAX_SIZE CONFIG_SYS_INIT_RAM_SIZE
>> +#if defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
>> +#define CONFIG_SPL_BOARD_INIT
>> +#endif
>
> SPL_BOARD_INIT is defined in socfpga_common.h
This file is socfpga_common.h.
>
>>
>> /* SPL SDMMC boot support */
>> #ifdef CONFIG_SPL_MMC_SUPPORT
>> @@ -346,10 +359,15 @@ unsigned int cm_get_qspi_controller_clk_hz(void);
>> #define BOOT_TARGET_DEVICES_MMC(func)
>> #endif
>>
>> +#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
>> #define BOOT_TARGET_DEVICES(func) \
>> BOOT_TARGET_DEVICES_MMC(func) \
>> BOOT_TARGET_DEVICES_PXE(func) \
>> func(DHCP, dhcp, na)
>> +#elif defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
>> +#define BOOT_TARGET_DEVICES(func) \
>> + BOOT_TARGET_DEVICES_MMC(func)
>> +#endif
>>
>
> Why doesn't A10 support PXE?
Same here, will remove switch for GEN5 and ARRIA10. All will use same
BOOT_TARGET_DEVICES().
Thanks.
Regards
Ley Foon
More information about the U-Boot
mailing list