[U-Boot] [PATCH v5 2/6] board: sama5d3xek: Clean up code

[Wenyou Yang]

Due to the introduction of the pinctrl and clk driver, and using
device tree files, remove the unneeded hardcoded pin configuration
and clock enabling code from the board file.

Signed-off-by: Wenyou Yang <wenyou.yang at atmel.com>
---

Changes in v5: None
Changes in v4:
 - Remove the ethernet init code completely.

Changes in v3: None
Changes in v2: None

 board/atmel/sama5d3xek/sama5d3xek.c | 134 +-----------------------------------
 1 file changed, 1 insertion(+), 133 deletions(-)

diff --git a/board/atmel/sama5d3xek/sama5d3xek.c b/board/atmel/sama5d3xek/sama5d3xek.c
index 1d96149921..2a18d877a2 100644
--- a/board/atmel/sama5d3xek/sama5d3xek.c
+++ b/board/atmel/sama5d3xek/sama5d3xek.c
@@ -6,7 +6,6 @@
  */
 
 #include <common.h>
-#include <mmc.h>
 #include <asm/io.h>
 #include <asm/arch/sama5d3_smc.h>
 #include <asm/arch/at91_common.h>
@@ -16,19 +15,12 @@
 #include <lcd.h>
 #include <linux/ctype.h>
 #include <atmel_hlcdc.h>
-#include <atmel_mci.h>
 #include <phy.h>
 #include <micrel.h>
-#include <net.h>
-#include <netdev.h>
 #include <spl.h>
 #include <asm/arch/atmel_mpddrc.h>
 #include <asm/arch/at91_wdt.h>
 
-#ifdef CONFIG_USB_GADGET_ATMEL_USBA
-#include <asm/arch/atmel_usba_udc.h>
-#endif
-
 DECLARE_GLOBAL_DATA_PTR;
 
 /* ------------------------------------------------------------------------- */
@@ -135,8 +127,6 @@ static void sama5d3xek_usb_hw_init(void)
 #ifdef CONFIG_GENERIC_ATMEL_MCI
 static void sama5d3xek_mci_hw_init(void)
 {
-	at91_mci_hw_init();
-
 	at91_set_pio_output(AT91_PIO_PORTB, 10, 0);	/* MCI0 Power */
 }
 #endif
@@ -217,12 +207,6 @@ void lcd_show_board_info(void)
 
 int board_early_init_f(void)
 {
-	at91_periph_clk_enable(ATMEL_ID_PIOA);
-	at91_periph_clk_enable(ATMEL_ID_PIOB);
-	at91_periph_clk_enable(ATMEL_ID_PIOC);
-	at91_periph_clk_enable(ATMEL_ID_PIOD);
-	at91_periph_clk_enable(ATMEL_ID_PIOE);
-
 	at91_seriald_hw_init();
 
 	return 0;
@@ -242,21 +226,9 @@ int board_init(void)
 #ifdef CONFIG_CMD_USB
 	sama5d3xek_usb_hw_init();
 #endif
-#ifdef CONFIG_USB_GADGET_ATMEL_USBA
-	at91_udp_hw_init();
-#endif
 #ifdef CONFIG_GENERIC_ATMEL_MCI
 	sama5d3xek_mci_hw_init();
 #endif
-#ifdef CONFIG_ATMEL_SPI
-	at91_spi0_hw_init(1 << 0);
-#endif
-#ifdef CONFIG_MACB
-	if (has_emac())
-		at91_macb_hw_init();
-	if (has_gmac())
-		at91_gmac_hw_init();
-#endif
 #ifdef CONFIG_LCD
 	if (has_lcdc())
 		sama5d3xek_lcd_hw_init();
@@ -271,106 +243,6 @@ int dram_init(void)
 	return 0;
 }
 
-int board_phy_config(struct phy_device *phydev)
-{
-	/* board specific timings for GMAC */
-	if (has_gmac()) {
-		/* rx data delay */
-		ksz9021_phy_extended_write(phydev,
-					   MII_KSZ9021_EXT_RGMII_RX_DATA_SKEW,
-					   0x2222);
-		/* tx data delay */
-		ksz9021_phy_extended_write(phydev,
-					   MII_KSZ9021_EXT_RGMII_TX_DATA_SKEW,
-					   0x2222);
-		/* rx/tx clock delay */
-		ksz9021_phy_extended_write(phydev,
-					   MII_KSZ9021_EXT_RGMII_CLOCK_SKEW,
-					   0xf2f4);
-	}
-
-	/* always run the PHY's config routine */
-	if (phydev->drv->config)
-		return phydev->drv->config(phydev);
-
-	return 0;
-}
-
-int board_eth_init(bd_t *bis)
-{
-	int rc = 0;
-
-#ifdef CONFIG_MACB
-	if (has_emac())
-		rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC, 0x00);
-	if (has_gmac())
-		rc = macb_eth_initialize(0, (void *)ATMEL_BASE_GMAC, 0x00);
-#endif
-#ifdef CONFIG_USB_GADGET_ATMEL_USBA
-	usba_udc_probe(&pdata);
-#ifdef CONFIG_USB_ETH_RNDIS
-	usb_eth_initialize(bis);
-#endif
-#endif
-
-	return rc;
-}
-
-#ifdef CONFIG_GENERIC_ATMEL_MCI
-int board_mmc_init(bd_t *bis)
-{
-	int rc = 0;
-
-	rc = atmel_mci_init((void *)ATMEL_BASE_MCI0);
-
-	return rc;
-}
-#endif
-
-/* SPI chip select control */
-#ifdef CONFIG_ATMEL_SPI
-#include <spi.h>
-
-#ifndef CONFIG_DM_SPI
-int spi_cs_is_valid(unsigned int bus, unsigned int cs)
-{
-	return bus == 0 && cs < 4;
-}
-
-void spi_cs_activate(struct spi_slave *slave)
-{
-	switch (slave->cs) {
-	case 0:
-		at91_set_pio_output(AT91_PIO_PORTD, 13, 0);
-	case 1:
-		at91_set_pio_output(AT91_PIO_PORTD, 14, 0);
-	case 2:
-		at91_set_pio_output(AT91_PIO_PORTD, 15, 0);
-	case 3:
-		at91_set_pio_output(AT91_PIO_PORTD, 16, 0);
-	default:
-		break;
-	}
-}
-
-void spi_cs_deactivate(struct spi_slave *slave)
-{
-	switch (slave->cs) {
-	case 0:
-		at91_set_pio_output(AT91_PIO_PORTD, 13, 1);
-	case 1:
-		at91_set_pio_output(AT91_PIO_PORTD, 14, 1);
-	case 2:
-		at91_set_pio_output(AT91_PIO_PORTD, 15, 1);
-	case 3:
-		at91_set_pio_output(AT91_PIO_PORTD, 16, 1);
-	default:
-		break;
-	}
-}
-#endif
-#endif /* CONFIG_ATMEL_SPI */
-
 #ifdef CONFIG_BOARD_LATE_INIT
 int board_late_init(void)
 {
@@ -394,12 +266,8 @@ int board_late_init(void)
 #ifdef CONFIG_SPL_BUILD
 void spl_board_init(void)
 {
-#ifdef CONFIG_SYS_USE_MMC
-	sama5d3xek_mci_hw_init();
-#elif CONFIG_SYS_USE_NANDFLASH
+#if CONFIG_SYS_USE_NANDFLASH
 	sama5d3xek_nand_hw_init();
-#elif CONFIG_SYS_USE_SERIALFLASH
-	at91_spi0_hw_init(1 << 0);
 #endif
 }
 
-- 
2.11.0