[U-Boot] [PATCH v2 1/3] rockchip: video: Add mipi dsi driver for rk3399
Eric Gao
eric.gao at rock-chips.com
Fri Apr 14 16:10:03 UTC 2017
Add mipi dsi driver for rk chip. To enable this you need to enable DM, DM_VIDEO
DM_ROCKCHIP_VIDEO, DISPLAY_MIPI in menuconfig. And enable rk808 and it's i2c.
Signed-off-by: Eric Gao <eric.gao at rock-chips.com>
---
arch/arm/include/asm/arch-rockchip/cru_rk3399.h | 1 +
arch/arm/include/asm/arch-rockchip/grf_rk3399.h | 25 ++
arch/arm/include/asm/arch-rockchip/mipi_rk3399.h | 195 ++++++++++
arch/arm/include/asm/arch-rockchip/vop_rk3288.h | 1 +
board/rockchip/evb_rk3399/evb-rk3399.c | 6 +
drivers/video/Kconfig | 2 +
drivers/video/rockchip/Kconfig | 38 ++
drivers/video/rockchip/Makefile | 6 +-
drivers/video/rockchip/rk_mipi.c | 464 +++++++++++++++++++++++
drivers/video/rockchip/rk_vop.c | 38 +-
10 files changed, 769 insertions(+), 7 deletions(-)
create mode 100644 arch/arm/include/asm/arch-rockchip/mipi_rk3399.h
create mode 100644 drivers/video/rockchip/Kconfig
create mode 100644 drivers/video/rockchip/rk_mipi.c
diff --git a/arch/arm/include/asm/arch-rockchip/cru_rk3399.h b/arch/arm/include/asm/arch-rockchip/cru_rk3399.h
index cf830d0..e9e5810 100644
--- a/arch/arm/include/asm/arch-rockchip/cru_rk3399.h
+++ b/arch/arm/include/asm/arch-rockchip/cru_rk3399.h
@@ -70,6 +70,7 @@ struct rk3399_cru {
};
check_member(rk3399_cru, sdio1_con[1], 0x594);
#define MHz 1000000
+#define MHZ 1000000
#define KHz 1000
#define OSC_HZ (24*MHz)
#define APLL_HZ (600*MHz)
diff --git a/arch/arm/include/asm/arch-rockchip/grf_rk3399.h b/arch/arm/include/asm/arch-rockchip/grf_rk3399.h
index 62d8496..2bf58da 100644
--- a/arch/arm/include/asm/arch-rockchip/grf_rk3399.h
+++ b/arch/arm/include/asm/arch-rockchip/grf_rk3399.h
@@ -399,6 +399,31 @@ enum {
GRF_UART_DBG_SEL_MASK = 3 << GRF_UART_DBG_SEL_SHIFT,
GRF_UART_DBG_SEL_C = 2,
+ /* GRF_SOC_CON20 */
+ GRF_DSI0_VOP_SEL_SHIFT = 0,
+ GRF_DSI0_VOP_SEL_MASK = 1 << GRF_DSI0_VOP_SEL_SHIFT,
+ GRF_DSI0_VOP_SEL_B = 0,
+ GRF_DSI0_VOP_SEL_L,
+
+ /* GRF_SOC_CON22 */
+ GRF_DPHY_TX0_RXMODE_SHIFT = 0,
+ GRF_DPHY_TX0_RXMODE_MASK =
+ 0xf << GRF_DPHY_TX0_RXMODE_SHIFT,
+ GRF_DPHY_TX0_RXMODE_EN = 0xb,
+ GRF_DPHY_TX0_RXMODE_DIS = 0,
+
+ GRF_DPHY_TX0_TXSTOPMODE_SHIFT = 4,
+ GRF_DPHY_TX0_TXSTOPMODE_MASK =
+ 0xf0 << GRF_DPHY_TX0_TXSTOPMODE_SHIFT,
+ GRF_DPHY_TX0_TXSTOPMODE_EN = 0xc,
+ GRF_DPHY_TX0_TXSTOPMODE_DIS = 0,
+
+ GRF_DPHY_TX0_TURNREQUEST_SHIFT = 12,
+ GRF_DPHY_TX0_TURNREQUEST_MASK =
+ 0xf000 << GRF_DPHY_TX0_TURNREQUEST_SHIFT,
+ GRF_DPHY_TX0_TURNREQUEST_EN = 0x1,
+ GRF_DPHY_TX0_TURNREQUEST_DIS = 0,
+
/* PMUGRF_GPIO0A_IOMUX */
PMUGRF_GPIO0A6_SEL_SHIFT = 12,
PMUGRF_GPIO0A6_SEL_MASK = 3 << PMUGRF_GPIO0A6_SEL_SHIFT,
diff --git a/arch/arm/include/asm/arch-rockchip/mipi_rk3399.h b/arch/arm/include/asm/arch-rockchip/mipi_rk3399.h
new file mode 100644
index 0000000..f55ffb6
--- /dev/null
+++ b/arch/arm/include/asm/arch-rockchip/mipi_rk3399.h
@@ -0,0 +1,195 @@
+/*
+ * Copyright (C) 2017-2025 Fuzhou Rockchip Electronics Co., Ltd
+ * author: Eric Gao <eric.gao at rock-chips.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef RK33_MIPI_DSI_H
+#define RK33_MIPI_DSI_H
+
+/*
+ * All these mipi controller register declaration provide reg address offset,
+ * bits width, bit offset for a specified register bits. With these message, we
+ * can set or clear every bits individually for a 32bit widthregister. We use
+ * DSI_HOST_BITS macro definition to combinat these message using the following
+ * format: val(32bit) = addr(16bit) | width(8bit) | offest(8bit)
+ * For example:
+ * #define SHUTDOWNZ DSI_HOST_BITS(0x004, 1, 0)
+ * means SHUTDOWNZ is a signal reg bit with bit offset qual 0,and it's reg addr
+ * offset is 0x004.The conbinat result = (0x004 << 16) | (1 << 8) | 0
+ */
+#define ADDR_SHIFT 16
+#define BITS_SHIFT 8
+#define OFFSET_SHIFT 0
+#define DSI_HOST_BITS(addr, bits, bit_offset) \
+((addr << ADDR_SHIFT) | (bits << BITS_SHIFT) | (bit_offset << OFFSET_SHIFT))
+
+/* DWC_DSI_VERSION_0x3133302A */
+#define VERSION DSI_HOST_BITS(0x000, 32, 0)
+#define SHUTDOWNZ DSI_HOST_BITS(0x004, 1, 0)
+#define TO_CLK_DIVISION DSI_HOST_BITS(0x008, 8, 8)
+#define TX_ESC_CLK_DIVISION DSI_HOST_BITS(0x008, 8, 0)
+#define DPI_VCID DSI_HOST_BITS(0x00c, 2, 0)
+#define EN18_LOOSELY DSI_HOST_BITS(0x010, 1, 8)
+#define DPI_COLOR_CODING DSI_HOST_BITS(0x010, 4, 0)
+#define COLORM_ACTIVE_LOW DSI_HOST_BITS(0x014, 1, 4)
+#define SHUTD_ACTIVE_LOW DSI_HOST_BITS(0x014, 1, 3)
+#define HSYNC_ACTIVE_LOW DSI_HOST_BITS(0x014, 1, 2)
+#define VSYNC_ACTIVE_LOW DSI_HOST_BITS(0x014, 1, 1)
+#define DATAEN_ACTIVE_LOW DSI_HOST_BITS(0x014, 1, 0)
+#define OUTVACT_LPCMD_TIME DSI_HOST_BITS(0x018, 8, 16)
+#define INVACT_LPCMD_TIME DSI_HOST_BITS(0x018, 8, 0)
+#define CRC_RX_EN DSI_HOST_BITS(0x02c, 1, 4)
+#define ECC_RX_EN DSI_HOST_BITS(0x02c, 1, 3)
+#define BTA_EN DSI_HOST_BITS(0x02c, 1, 2)
+#define EOTP_RX_EN DSI_HOST_BITS(0x02c, 1, 1)
+#define EOTP_TX_EN DSI_HOST_BITS(0x02c, 1, 0)
+#define GEN_VID_RX DSI_HOST_BITS(0x030, 2, 0)
+#define CMD_VIDEO_MODE DSI_HOST_BITS(0x034, 1, 0)
+#define VPG_ORIENTATION DSI_HOST_BITS(0x038, 1, 24)
+#define VPG_MODE DSI_HOST_BITS(0x038, 1, 20)
+#define VPG_EN DSI_HOST_BITS(0x038, 1, 16)
+#define LP_CMD_EN DSI_HOST_BITS(0x038, 1, 15)
+#define FRAME_BTA_ACK_EN DSI_HOST_BITS(0x038, 1, 14)
+#define LP_HFP_EN DSI_HOST_BITS(0x038, 1, 13)
+#define LP_HBP_EN DSI_HOST_BITS(0x038, 1, 12)
+#define LP_VACT_EN DSI_HOST_BITS(0x038, 1, 11)
+#define LP_VFP_EN DSI_HOST_BITS(0x038, 1, 10)
+#define LP_VBP_EN DSI_HOST_BITS(0x038, 1, 9)
+#define LP_VSA_EN DSI_HOST_BITS(0x038, 1, 8)
+#define VID_MODE_TYPE DSI_HOST_BITS(0x038, 2, 0)
+#define VID_PKT_SIZE DSI_HOST_BITS(0x03c, 14, 0)
+#define NUM_CHUNKS DSI_HOST_BITS(0x040, 13, 0)
+#define NULL_PKT_SIZE DSI_HOST_BITS(0x044, 13, 0)
+#define VID_HSA_TIME DSI_HOST_BITS(0x048, 12, 0)
+#define VID_HBP_TIME DSI_HOST_BITS(0x04c, 12, 0)
+#define VID_HLINE_TIME DSI_HOST_BITS(0x050, 15, 0)
+#define VID_VSA_LINES DSI_HOST_BITS(0x054, 10, 0)
+#define VID_VBP_LINES DSI_HOST_BITS(0x058, 10, 0)
+#define VID_VFP_LINES DSI_HOST_BITS(0x05c, 10, 0)
+#define VID_ACTIVE_LINES DSI_HOST_BITS(0x060, 14, 0)
+#define EDPI_CMD_SIZE DSI_HOST_BITS(0x064, 16, 0)
+#define MAX_RD_PKT_SIZE DSI_HOST_BITS(0x068, 1, 24)
+#define DCS_LW_TX DSI_HOST_BITS(0x068, 1, 19)
+#define DCS_SR_0P_TX DSI_HOST_BITS(0x068, 1, 18)
+#define DCS_SW_1P_TX DSI_HOST_BITS(0x068, 1, 17)
+#define DCS_SW_0P_TX DSI_HOST_BITS(0x068, 1, 16)
+#define GEN_LW_TX DSI_HOST_BITS(0x068, 1, 14)
+#define GEN_SR_2P_TX DSI_HOST_BITS(0x068, 1, 13)
+#define GEN_SR_1P_TX DSI_HOST_BITS(0x068, 1, 12)
+#define GEN_SR_0P_TX DSI_HOST_BITS(0x068, 1, 11)
+#define GEN_SW_2P_TX DSI_HOST_BITS(0x068, 1, 10)
+#define GEN_SW_1P_TX DSI_HOST_BITS(0x068, 1, 9)
+#define GEN_SW_0P_TX DSI_HOST_BITS(0x068, 1, 8)
+#define ACK_RQST_EN DSI_HOST_BITS(0x068, 1, 1)
+#define TEAR_FX_EN DSI_HOST_BITS(0x068, 1, 0)
+#define GEN_WC_MSBYTE DSI_HOST_BITS(0x06c, 14, 16)
+#define GEN_WC_LSBYTE DSI_HOST_BITS(0x06c, 8, 8)
+#define GEN_VC DSI_HOST_BITS(0x06c, 2, 6)
+#define GEN_DT DSI_HOST_BITS(0x06c, 6, 0)
+#define GEN_PLD_DATA DSI_HOST_BITS(0x070, 32, 0)
+#define GEN_RD_CMD_BUSY DSI_HOST_BITS(0x074, 1, 6)
+#define GEN_PLD_R_FULL DSI_HOST_BITS(0x074, 1, 5)
+#define GEN_PLD_R_EMPTY DSI_HOST_BITS(0x074, 1, 4)
+#define GEN_PLD_W_FULL DSI_HOST_BITS(0x074, 1, 3)
+#define GEN_PLD_W_EMPTY DSI_HOST_BITS(0x074, 1, 2)
+#define GEN_CMD_FULL DSI_HOST_BITS(0x074, 1, 1)
+#define GEN_CMD_EMPTY DSI_HOST_BITS(0x074, 1, 0)
+#define HSTX_TO_CNT DSI_HOST_BITS(0x078, 16, 16)
+#define LPRX_TO_CNT DSI_HOST_BITS(0x078, 16, 0)
+#define HS_RD_TO_CNT DSI_HOST_BITS(0x07c, 16, 0)
+#define LP_RD_TO_CNT DSI_HOST_BITS(0x080, 16, 0)
+#define PRESP_TO_MODE DSI_HOST_BITS(0x084, 1, 24)
+#define HS_WR_TO_CNT DSI_HOST_BITS(0x084, 16, 0)
+#define LP_WR_TO_CNT DSI_HOST_BITS(0x088, 16, 0)
+#define BTA_TO_CNT DSI_HOST_BITS(0x08c, 16, 0)
+#define AUTO_CLKLANE_CTRL DSI_HOST_BITS(0x094, 1, 1)
+#define PHY_TXREQUESTCLKHS DSI_HOST_BITS(0x094, 1, 0)
+#define PHY_HS2LP_TIME_CLK_LANE DSI_HOST_BITS(0x098, 10, 16)
+#define PHY_HS2HS_TIME_CLK_LANE DSI_HOST_BITS(0x098, 10, 0)
+#define PHY_HS2LP_TIME DSI_HOST_BITS(0x09c, 8, 24)
+#define PHY_LP2HS_TIME DSI_HOST_BITS(0x09c, 8, 16)
+#define MAX_RD_TIME DSI_HOST_BITS(0x09c, 15, 0)
+#define PHY_FORCEPLL DSI_HOST_BITS(0x0a0, 1, 3)
+#define PHY_ENABLECLK DSI_HOST_BITS(0x0a0, 1, 2)
+#define PHY_RSTZ DSI_HOST_BITS(0x0a0, 1, 1)
+#define PHY_SHUTDOWNZ DSI_HOST_BITS(0x0a0, 1, 0)
+#define PHY_STOP_WAIT_TIME DSI_HOST_BITS(0x0a4, 8, 8)
+#define N_LANES DSI_HOST_BITS(0x0a4, 2, 0)
+#define PHY_TXEXITULPSLAN DSI_HOST_BITS(0x0a8, 1, 3)
+#define PHY_TXREQULPSLAN DSI_HOST_BITS(0x0a8, 1, 2)
+#define PHY_TXEXITULPSCLK DSI_HOST_BITS(0x0a8, 1, 1)
+#define PHY_TXREQULPSCLK DSI_HOST_BITS(0x0a8, 1, 0)
+#define PHY_TX_TRIGGERS DSI_HOST_BITS(0x0ac, 4, 0)
+#define PHYSTOPSTATECLKLANE DSI_HOST_BITS(0x0b0, 1, 2)
+#define PHYLOCK DSI_HOST_BITS(0x0b0, 1, 0)
+#define PHY_TESTCLK DSI_HOST_BITS(0x0b4, 1, 1)
+#define PHY_TESTCLR DSI_HOST_BITS(0x0b4, 1, 0)
+#define PHY_TESTEN DSI_HOST_BITS(0x0b8, 1, 16)
+#define PHY_TESTDOUT DSI_HOST_BITS(0x0b8, 8, 8)
+#define PHY_TESTDIN DSI_HOST_BITS(0x0b8, 8, 0)
+#define PHY_TEST_CTRL1 DSI_HOST_BITS(0x0b8, 17, 0)
+#define PHY_TEST_CTRL0 DSI_HOST_BITS(0x0b4, 2, 0)
+#define INT_ST0 DSI_HOST_BITS(0x0bc, 21, 0)
+#define INT_ST1 DSI_HOST_BITS(0x0c0, 18, 0)
+#define INT_MKS0 DSI_HOST_BITS(0x0c4, 21, 0)
+#define INT_MKS1 DSI_HOST_BITS(0x0c8, 18, 0)
+#define INT_FORCE0 DSI_HOST_BITS(0x0d8, 21, 0)
+#define INT_FORCE1 DSI_HOST_BITS(0x0dc, 18, 0)
+
+#define CODE_HS_RX_CLOCK 0x34
+#define CODE_HS_RX_LANE0 0x44
+#define CODE_HS_RX_LANE1 0x54
+#define CODE_HS_RX_LANE2 0x84
+#define CODE_HS_RX_LANE3 0x94
+
+#define CODE_PLL_VCORANGE_VCOCAP 0x10
+#define CODE_PLL_CPCTRL 0x11
+#define CODE_PLL_LPF_CP 0x12
+#define CODE_PLL_INPUT_DIV_RAT 0x17
+#define CODE_PLL_LOOP_DIV_RAT 0x18
+#define CODE_PLL_INPUT_LOOP_DIV_RAT 0x19
+#define CODE_BANDGAP_BIAS_CTRL 0x20
+#define CODE_TERMINATION_CTRL 0x21
+#define CODE_AFE_BIAS_BANDGAP_ANOLOG 0x22
+
+#define CODE_HSTXDATALANEREQUSETSTATETIME 0x70
+#define CODE_HSTXDATALANEPREPARESTATETIME 0x71
+#define CODE_HSTXDATALANEHSZEROSTATETIME 0x72
+
+/* Transmission mode between vop and MIPI controller */
+enum vid_mode_type_t {
+ NON_BURST_SYNC_PLUSE = 0,
+ NON_BURST_SYNC_EVENT,
+ BURST_MODE,
+};
+
+enum cmd_video_mode {
+ VIDEO_MODE = 0,
+ CMD_MODE,
+};
+
+/* Indicate MIPI DSI color mode */
+enum dpi_color_coding {
+ DPI_16BIT_CFG_1 = 0,
+ DPI_16BIT_CFG_2,
+ DPI_16BIT_CFG_3,
+ DPI_18BIT_CFG_1,
+ DPI_18BIT_CFG_2,
+ DPI_24BIT,
+ DPI_20BIT_YCBCR_422_LP,
+ DPI_24BIT_YCBCR_422,
+ DPI_16BIT_YCBCR_422,
+ DPI_30BIT,
+ DPI_36BIT,
+ DPI_12BIT_YCBCR_420,
+};
+
+/* Indicate which VOP the MIPI DSI use, bit or little one */
+enum vop_id {
+ VOP_B = 0,
+ VOP_L,
+};
+
+#endif /* end of RK33_MIPI_DSI_H */
diff --git a/arch/arm/include/asm/arch-rockchip/vop_rk3288.h b/arch/arm/include/asm/arch-rockchip/vop_rk3288.h
index 0ce3d67..d5599ec 100644
--- a/arch/arm/include/asm/arch-rockchip/vop_rk3288.h
+++ b/arch/arm/include/asm/arch-rockchip/vop_rk3288.h
@@ -90,6 +90,7 @@ enum vop_modes {
VOP_MODE_EDP = 0,
VOP_MODE_HDMI,
VOP_MODE_LVDS,
+ VOP_MODE_MIPI,
VOP_MODE_NONE,
VOP_MODE_AUTO_DETECT,
VOP_MODE_UNKNOWN,
diff --git a/board/rockchip/evb_rk3399/evb-rk3399.c b/board/rockchip/evb_rk3399/evb-rk3399.c
index c437f1b..ec2b023 100644
--- a/board/rockchip/evb_rk3399/evb-rk3399.c
+++ b/board/rockchip/evb_rk3399/evb-rk3399.c
@@ -28,6 +28,12 @@ int board_init(void)
goto out;
}
+ ret = pinctrl_request_noflags(pinctrl, PERIPH_ID_PWM0);
+ if (ret) {
+ debug("%s PWM0 pinctrl init fail!\n", __func__);
+ goto out;
+ }
+
ret = pinctrl_request_noflags(pinctrl, PERIPH_ID_PWM2);
if (ret) {
debug("%s PWM2 pinctrl init fail!\n", __func__);
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index 2069576..4b03a9a 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -405,6 +405,8 @@ config VIDEO_ROCKCHIP
(DSI). This driver supports the on-chip video output device, and
targets the Rockchip RK3288.
+source "drivers/video/rockchip/Kconfig"
+
config VIDEO_SANDBOX_SDL
bool "Enable sandbox video console using SDL"
depends on SANDBOX
diff --git a/drivers/video/rockchip/Kconfig b/drivers/video/rockchip/Kconfig
new file mode 100644
index 0000000..811be83
--- /dev/null
+++ b/drivers/video/rockchip/Kconfig
@@ -0,0 +1,38 @@
+#
+# Video drivers selection for rockchip soc. These configs only impact the
+# compile process. You can surely check all the options. In this case, all the
+# display driver will be compiled, but which drivers finally will be used is
+# decided by device tree configuration. What's more, enable needed power for
+# display by configure the device tree, and the vop driver will do the rest.
+#
+# Author: Eric Gao <eric.gao at rock-chips.com>
+#
+
+menu "Video Display Port"
+
+config DISPLAY_MIPI
+ bool "MIPI Port"
+ depends on VIDEO_ROCKCHIP
+ help
+ "Mobile Industry Processor Interface"
+ This MIPI Controller and MIPI PHY is designed by Synopsys, which
+ support 16,18, 24 bits per pixel. And upto 2k resolution ratio.
+
+config DISPLAY_EDP
+ bool "EDP Port"
+ depends on VIDEO_ROCKCHIP
+ help
+ "Embedded DisplayPort"
+
+config DISPLAY_LVDS
+ bool "LVDS Port"
+ depends on VIDEO_ROCKCHIP
+ help
+ "Low-voltage Differential Signaling"
+
+config DISPLAY_HDMI
+ bool "HDMI port"
+ depends on VIDEO_ROCKCHIP
+ help
+ "High-Definition Multimedia Interface"
+endmenu
diff --git a/drivers/video/rockchip/Makefile b/drivers/video/rockchip/Makefile
index 7962f86..a14db04 100644
--- a/drivers/video/rockchip/Makefile
+++ b/drivers/video/rockchip/Makefile
@@ -5,4 +5,8 @@
# SPDX-License-Identifier: GPL-2.0+
#
-obj-y += rk_edp.o rk_hdmi.o rk_vop.o rk_lvds.o
+obj-$(CONFIG_VIDEO_ROCKCHIP) += rk_vop.o
+obj-$(CONFIG_DISPLAY_MIPI) += rk_mipi.o
+obj-$(CONFIG_DISPLAY_EDP) += rk_edp.o
+obj-$(CONFIG_DISPLAY_LVDS) += rk_lvds.o
+obj-$(CONFIG_DISPLAY_HDMI) += rk_hdmi.o
diff --git a/drivers/video/rockchip/rk_mipi.c b/drivers/video/rockchip/rk_mipi.c
new file mode 100644
index 0000000..58541d6
--- /dev/null
+++ b/drivers/video/rockchip/rk_mipi.c
@@ -0,0 +1,464 @@
+/*
+ * Copyright (c) 2016, Fuzhou Rockchip Electronics Co., Ltd
+ * Author: Eric Gao <eric.gao at rock-chips.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <clk.h>
+#include <display.h>
+#include <dm.h>
+#include <dt-bindings/clock/rk3288-cru.h>
+#include <dm/uclass-internal.h>
+#include <fdtdec.h>
+#include <panel.h>
+#include <regmap.h>
+#include <syscon.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <asm/hardware.h>
+#include <asm/arch/mipi_rk3399.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/grf_rk3399.h>
+#include <asm/arch/cru_rk3399.h>
+#include <linux/kernel.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+struct mipi_dsi {
+ u32 ref_clk;
+ u32 sys_clk;
+ u32 pix_clk;
+ u32 phy_clk;
+ u32 txbyte_clk;
+ u32 txesc_clk;
+};
+
+struct rk_mipi_priv {
+ void __iomem *regs;
+ struct rk3399_grf_regs *grf;
+ struct udevice *panel;
+ struct mipi_dsi *dsi;
+};
+
+static int rk_mipi_read_timing(struct udevice *dev,
+ struct display_timing *timing)
+{
+ if (fdtdec_decode_display_timing(gd->fdt_blob, dev_of_offset(dev),
+ 0, timing)) {
+ debug("%s: Failed to decode display timing\n", __func__);
+ return -EINVAL;
+ }
+
+ return 0;
+}
+/*
+ * Register write function used only for mipi dsi controller.
+ * Parameter:
+ * reg: combination of regaddr(16bit)|bitswidth(8bit)|offset(8bit) you can use
+ * define in rk_mipi.h directly for this parameter
+ * val: value that will be write to specified bits of register
+ */
+static void rk_mipi_dsi_write(u32 regs, u32 reg, u32 val)
+{
+ u32 dat;
+ u32 mask;
+ u32 offset = (reg >> OFFSET_SHIFT & 0xff);
+ u32 bits = ((reg >> BITS_SHIFT) & 0xff);
+ u64 addr = ((reg >> ADDR_SHIFT) + regs);
+
+ /* Mask for specifiled bits,the corresponding bits will be clear */
+ mask = (~((0xffffffff << offset) & (0xffffffff >>
+ (32 - offset - bits))));
+
+ /* Make sure val in the available range */
+ val &= (~(0xffffffff << bits));
+
+ /* Get register's original val */
+ dat = readl(addr);
+
+ /* Clear specified bits */
+ dat &= mask;
+
+ /* Fill specified bits */
+ dat |= (val << offset);
+
+ writel(dat, addr);
+}
+
+static int rk_mipi_dsi_enable(struct udevice *dev,
+ const struct display_timing *timing)
+{
+ int node, timing_node;
+ int val;
+ struct rk_mipi_priv *priv = dev_get_priv(dev);
+ u64 regs = (u64)(priv->regs);
+ struct display_plat *disp_uc_plat = dev_get_uclass_platdata(dev);
+ u32 txbyte_clk = priv->dsi->txbyte_clk;
+ u32 txesc_clk = priv->dsi->txesc_clk;
+
+ txesc_clk = txbyte_clk/(txbyte_clk/txesc_clk + 1);
+
+ /* Select the video source */
+ switch (disp_uc_plat->source_id) {
+ case VOP_B:
+ rk_clrsetreg(&priv->grf->soc_con20, GRF_DSI0_VOP_SEL_MASK,
+ GRF_DSI0_VOP_SEL_B << GRF_DSI0_VOP_SEL_SHIFT);
+ break;
+ case VOP_L:
+ rk_clrsetreg(&priv->grf->soc_con20, GRF_DSI0_VOP_SEL_MASK,
+ GRF_DSI0_VOP_SEL_L << GRF_DSI0_VOP_SEL_SHIFT);
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ /* Set Controller as TX mode */
+ val = GRF_DPHY_TX0_RXMODE_DIS << GRF_DPHY_TX0_RXMODE_SHIFT;
+ rk_clrsetreg(&priv->grf->soc_con22, GRF_DPHY_TX0_RXMODE_MASK, val);
+
+ /* Exit tx stop mode */
+ val |= GRF_DPHY_TX0_TXSTOPMODE_DIS << GRF_DPHY_TX0_TXSTOPMODE_SHIFT;
+ rk_clrsetreg(&priv->grf->soc_con22, GRF_DPHY_TX0_TXSTOPMODE_MASK, val);
+
+ /* Disable turnequest */
+ val |= GRF_DPHY_TX0_TURNREQUEST_DIS << GRF_DPHY_TX0_TURNREQUEST_SHIFT;
+ rk_clrsetreg(&priv->grf->soc_con22, GRF_DPHY_TX0_TURNREQUEST_MASK, val);
+
+ /* Set Display timing parameter */
+ rk_mipi_dsi_write(regs, VID_HSA_TIME, timing->hsync_len.typ);
+ rk_mipi_dsi_write(regs, VID_HBP_TIME, timing->hback_porch.typ);
+ rk_mipi_dsi_write(regs, VID_HLINE_TIME, (timing->hsync_len.typ
+ + timing->hback_porch.typ + timing->hactive.typ
+ + timing->hfront_porch.typ));
+ rk_mipi_dsi_write(regs, VID_VSA_LINES, timing->vsync_len.typ);
+ rk_mipi_dsi_write(regs, VID_VBP_LINES, timing->vback_porch.typ);
+ rk_mipi_dsi_write(regs, VID_VFP_LINES, timing->vfront_porch.typ);
+ rk_mipi_dsi_write(regs, VID_ACTIVE_LINES, timing->vactive.typ);
+
+ /* Set Signal Polarity */
+ val = (timing->flags & DISPLAY_FLAGS_HSYNC_LOW) ? 1 : 0;
+ rk_mipi_dsi_write(regs, HSYNC_ACTIVE_LOW, val);
+
+ val = (timing->flags & DISPLAY_FLAGS_VSYNC_LOW) ? 1 : 0;
+ rk_mipi_dsi_write(regs, VSYNC_ACTIVE_LOW, val);
+
+ val = (timing->flags & DISPLAY_FLAGS_DE_LOW) ? 1 : 0;
+ rk_mipi_dsi_write(regs, DISPLAY_FLAGS_DE_LOW, val);
+
+ val = (timing->flags & DISPLAY_FLAGS_PIXDATA_NEGEDGE) ? 1 : 0;
+ rk_mipi_dsi_write(regs, COLORM_ACTIVE_LOW, val);
+
+ /* Set video mode */
+ rk_mipi_dsi_write(regs, CMD_VIDEO_MODE, VIDEO_MODE);
+
+ /* Set video mode transmission type as burst mode */
+ rk_mipi_dsi_write(regs, VID_MODE_TYPE, BURST_MODE);
+
+ /* Set pix num in a video package */
+ rk_mipi_dsi_write(regs, VID_PKT_SIZE, 0x4b0);
+
+ /* Set dpi color coding depth 24 bit */
+ timing_node = fdt_subnode_offset(gd->fdt_blob, dev_of_offset(dev),
+ "display-timings");
+ node = fdt_first_subnode(gd->fdt_blob, timing_node);
+ val = fdtdec_get_int(gd->fdt_blob, node, "bits-per-pixel", -1);
+ switch (val) {
+ case 16:
+ rk_mipi_dsi_write(regs, DPI_COLOR_CODING, DPI_16BIT_CFG_1);
+ break;
+ case 24:
+ rk_mipi_dsi_write(regs, DPI_COLOR_CODING, DPI_24BIT);
+ break;
+ case 30:
+ rk_mipi_dsi_write(regs, DPI_COLOR_CODING, DPI_30BIT);
+ break;
+ default:
+ rk_mipi_dsi_write(regs, DPI_COLOR_CODING, DPI_24BIT);
+ }
+ /* Enable low power mode */
+ rk_mipi_dsi_write(regs, LP_CMD_EN, 1);
+ rk_mipi_dsi_write(regs, LP_HFP_EN, 1);
+ rk_mipi_dsi_write(regs, LP_VACT_EN, 1);
+ rk_mipi_dsi_write(regs, LP_VFP_EN, 1);
+ rk_mipi_dsi_write(regs, LP_VBP_EN, 1);
+ rk_mipi_dsi_write(regs, LP_VSA_EN, 1);
+
+ /* Division for timeout counter clk */
+ rk_mipi_dsi_write(regs, TO_CLK_DIVISION, 0x0a);
+
+ /* Tx esc clk division from txbyte clk */
+ rk_mipi_dsi_write(regs, TX_ESC_CLK_DIVISION, txbyte_clk/txesc_clk);
+
+ /* Timeout count for hs<->lp transation between Line period */
+ rk_mipi_dsi_write(regs, HSTX_TO_CNT, 0x3e8);
+
+ /* Phy State transfer timing */
+ rk_mipi_dsi_write(regs, PHY_STOP_WAIT_TIME, 32);
+ rk_mipi_dsi_write(regs, PHY_TXREQUESTCLKHS, 1);
+ rk_mipi_dsi_write(regs, PHY_HS2LP_TIME, 0x14);
+ rk_mipi_dsi_write(regs, PHY_LP2HS_TIME, 0x10);
+ rk_mipi_dsi_write(regs, MAX_RD_TIME, 0x2710);
+
+ /* Power on */
+ rk_mipi_dsi_write(regs, SHUTDOWNZ, 1);
+
+ return 0;
+}
+
+/* rk mipi dphy write function */
+static void rk_mipi_phy_write(u32 regs, unsigned char test_code,
+ unsigned char *test_data, unsigned char size)
+{
+ int i = 0;
+ /* Write Test code */
+ rk_mipi_dsi_write(regs, PHY_TESTCLK, 1);
+ rk_mipi_dsi_write(regs, PHY_TESTDIN, test_code);
+ rk_mipi_dsi_write(regs, PHY_TESTEN, 1);
+ rk_mipi_dsi_write(regs, PHY_TESTCLK, 0);
+ rk_mipi_dsi_write(regs, PHY_TESTEN, 0);
+
+ /* Write Test data */
+ for (i = 0; i < size; i++) {
+ rk_mipi_dsi_write(regs, PHY_TESTCLK, 0);
+ rk_mipi_dsi_write(regs, PHY_TESTDIN, test_data[i]);
+ rk_mipi_dsi_write(regs, PHY_TESTCLK, 1);
+ }
+}
+
+/*
+ * Mipi dphy config function. Calculate the suitable prediv, feedback div,
+ * fsfreqrang value ,cap ,lpf and so on according to the given pix clk rate,
+ * and then enable phy.
+ */
+static int rk_mipi_phy_enable(struct udevice *dev)
+{
+ int i;
+ struct rk_mipi_priv *priv = dev_get_priv(dev);
+ u64 regs = (u64)(priv->regs);
+ u64 fbdiv;
+ u64 prediv = 1;
+ u32 max_fbdiv = 512;
+ u32 max_prediv, min_prediv;
+ u64 ddr_clk = priv->dsi->phy_clk;
+ u32 refclk = priv->dsi->ref_clk;
+ u32 remain = refclk;
+ unsigned char test_data[2] = {0};
+
+ int freq_rang[][2] = {
+ {90, 0x01}, {100, 0x10}, {110, 0x20}, {130, 0x01},
+ {140, 0x11}, {150, 0x21}, {170, 0x02}, {180, 0x12},
+ {200, 0x22}, {220, 0x03}, {240, 0x13}, {250, 0x23},
+ {270, 0x04}, {300, 0x14}, {330, 0x05}, {360, 0x15},
+ {400, 0x25}, {450, 0x06}, {500, 0x16}, {550, 0x07},
+ {600, 0x17}, {650, 0x08}, {700, 0x18}, {750, 0x09},
+ {800, 0x19}, {850, 0x29}, {900, 0x39}, {950, 0x0a},
+ {1000, 0x1a}, {1050, 0x2a}, {1100, 0x3a}, {1150, 0x0b},
+ {1200, 0x1b}, {1250, 0x2b}, {1300, 0x3b}, {1350, 0x0c},
+ {1400, 0x1c}, {1450, 0x2c}, {1500, 0x3c}
+ };
+
+ /* Shutdown mode */
+ rk_mipi_dsi_write(regs, PHY_SHUTDOWNZ, 0);
+ rk_mipi_dsi_write(regs, PHY_RSTZ, 0);
+ rk_mipi_dsi_write(regs, PHY_TESTCLR, 1);
+
+ /* Pll locking */
+ rk_mipi_dsi_write(regs, PHY_TESTCLR, 0);
+
+ /* config cp and lfp */
+ test_data[0] = 0x80 | (ddr_clk / (200 * MHZ)) << 3 | 0x3;
+ rk_mipi_phy_write(regs, CODE_PLL_VCORANGE_VCOCAP, test_data, 1);
+
+ test_data[0] = 0x8;
+ rk_mipi_phy_write(regs, CODE_PLL_CPCTRL, test_data, 1);
+
+ test_data[0] = 0x80 | 0x40;
+ rk_mipi_phy_write(regs, CODE_PLL_LPF_CP, test_data, 1);
+
+ /* select the suitable value for fsfreqrang reg */
+ for (i = 0; i < ARRAY_SIZE(freq_rang); i++) {
+ if (ddr_clk / (MHZ) >= freq_rang[i][0])
+ break;
+ }
+ if (i == ARRAY_SIZE(freq_rang)) {
+ debug("%s@%d: Dphy freq out of range!\n", __func__, __LINE__);
+ return -EINVAL;
+ }
+ test_data[0] = freq_rang[i][1] << 1;
+ rk_mipi_phy_write(regs, CODE_HS_RX_LANE0, test_data, 1);
+
+ /*
+ * Calculate the best ddrclk and it's corresponding div value. If the
+ * given pixelclock is great than 250M, ddrclk will be fix 1500M.
+ * Otherwise,
+ * it's equal to ddr_clk= pixclk * 6. 40MHZ >= refclk / prediv >= 5MHZ
+ * according to spec.
+ */
+ max_prediv = (refclk / (5 * MHZ));
+ min_prediv = ((refclk / (40 * MHZ)) ? (refclk / (40 * MHZ) + 1) : 1);
+
+ debug("%s@%d:DEBUG: MAX_PREDIV=%u, MIN_PREDIV=%u\n", __func__, __LINE__,
+ max_prediv, min_prediv);
+
+ if (max_prediv < min_prediv) {
+ debug("%s@%d: Err: Invalid refclk value\n", __func__, __LINE__);
+ return -EINVAL;
+ }
+
+ /* Calculate the best refclk and feedback division value for dphy pll */
+ for (i = min_prediv; i < max_prediv; i++) {
+ if ((ddr_clk * i % refclk < remain) &&
+ (ddr_clk * i / refclk) < max_fbdiv) {
+ prediv = i;
+ remain = ddr_clk * i % refclk;
+ }
+ }
+ fbdiv = ddr_clk * prediv / refclk;
+ ddr_clk = refclk * fbdiv / prediv;
+ priv->dsi->phy_clk = ddr_clk;
+
+ debug("%s@%d: DEBUG: refclk=%u, refclk=%llu, fbdiv=%llu, phyclk=%llu\n",
+ __func__, __LINE__, refclk, prediv, fbdiv, ddr_clk);
+
+ /* config prediv and feedback reg */
+ test_data[0] = prediv - 1;
+ rk_mipi_phy_write(regs, CODE_PLL_INPUT_DIV_RAT, test_data, 1);
+ test_data[0] = (fbdiv - 1) & 0x1f;
+ rk_mipi_phy_write(regs, CODE_PLL_LOOP_DIV_RAT, test_data, 1);
+ test_data[0] = (fbdiv - 1) >> 5 | 0x80;
+ rk_mipi_phy_write(regs, CODE_PLL_LOOP_DIV_RAT, test_data, 1);
+ test_data[0] = 0x30;
+ rk_mipi_phy_write(regs, CODE_PLL_INPUT_LOOP_DIV_RAT, test_data, 1);
+
+ /* rest config */
+ test_data[0] = 0x4d;
+ rk_mipi_phy_write(regs, CODE_BANDGAP_BIAS_CTRL, test_data, 1);
+
+ test_data[0] = 0x3d;
+ rk_mipi_phy_write(regs, CODE_TERMINATION_CTRL, test_data, 1);
+
+ test_data[0] = 0xdf;
+ rk_mipi_phy_write(regs, CODE_TERMINATION_CTRL, test_data, 1);
+
+ test_data[0] = 0x7;
+ rk_mipi_phy_write(regs, CODE_AFE_BIAS_BANDGAP_ANOLOG, test_data, 1);
+
+ test_data[0] = 0x80 | 0x7;
+ rk_mipi_phy_write(regs, CODE_AFE_BIAS_BANDGAP_ANOLOG, test_data, 1);
+
+ test_data[0] = 0x80 | 15;
+ rk_mipi_phy_write(regs, CODE_HSTXDATALANEREQUSETSTATETIME,
+ test_data, 1);
+ test_data[0] = 0x80 | 85;
+ rk_mipi_phy_write(regs, CODE_HSTXDATALANEPREPARESTATETIME,
+ test_data, 1);
+ test_data[0] = 0x40 | 10;
+ rk_mipi_phy_write(regs, CODE_HSTXDATALANEHSZEROSTATETIME,
+ test_data, 1);
+
+ /* enter into stop mode */
+ rk_mipi_dsi_write(regs, N_LANES, 0x03);
+ rk_mipi_dsi_write(regs, PHY_ENABLECLK, 1);
+ rk_mipi_dsi_write(regs, PHY_FORCEPLL, 1);
+ rk_mipi_dsi_write(regs, PHY_SHUTDOWNZ, 1);
+ rk_mipi_dsi_write(regs, PHY_RSTZ, 1);
+
+ return 0;
+}
+
+static int rk_mipi_enable(struct udevice *dev, int panel_bpp,
+ const struct display_timing *timing)
+{
+ return 0;
+}
+
+static int rk_mipi_ofdata_to_platdata(struct udevice *dev)
+{
+ struct rk_mipi_priv *priv = dev_get_priv(dev);
+
+ priv->grf = syscon_get_first_range(ROCKCHIP_SYSCON_GRF);
+ if (!priv->grf) {
+ debug("%s@%d: Get syscon ref fail\n", __func__, __LINE__);
+ return -ENXIO;
+ }
+ priv->regs = (void *)dev_get_addr(dev);
+ if (!priv->regs) {
+ debug("%s@%d: Get MIPI dsi address fail\n", __func__, __LINE__);
+ return -ENXIO;
+ }
+
+ return 0;
+}
+
+/*
+ * Probe function: check panel existence and readingit's timing. Then config
+ * mipi dsi controller and enable it according to the timing parameter.
+ */
+static int rk_mipi_probe(struct udevice *dev)
+{
+ struct rk_mipi_priv *priv = dev_get_priv(dev);
+ struct display_timing timing;
+ int ret;
+
+ ret = uclass_get_device_by_phandle(UCLASS_PANEL, dev, "rockchip,panel",
+ &priv->panel);
+ if (ret) {
+ debug("Err:Can't find panel@%s, ret = %d\n", __func__, ret);
+ return ret;
+ }
+ /* Read panel timing,and save to struct timing */
+ rk_mipi_read_timing(dev, &timing);
+
+ /* fill the mipi controller parameter */
+ priv->dsi->ref_clk = 24*MHZ;
+ priv->dsi->sys_clk = priv->dsi->ref_clk;
+ priv->dsi->pix_clk = timing.pixelclock.typ;
+ priv->dsi->phy_clk = priv->dsi->pix_clk * 6;
+ priv->dsi->txbyte_clk = priv->dsi->phy_clk / 8;
+ priv->dsi->txesc_clk = 20*MHZ;
+
+ /* config mipi dsi according to timing and enable it */
+ ret = rk_mipi_dsi_enable(dev, &timing);
+ if (ret) {
+ debug("Err: mipi dsi enable fail@%s,ret=%d\n", __func__, ret);
+ return ret;
+ }
+
+ /* init mipi dsi phy */
+ ret = rk_mipi_phy_enable(dev);
+ if (ret) {
+ debug("Err: mipi phy enable fail@%s,ret=%d\n", __func__, ret);
+ return ret;
+ }
+
+ /* enable backlight */
+ ret = panel_enable_backlight(priv->panel);
+ if (ret) {
+ debug("Err: fail to enable bg@%s,ret=%d\n", __func__, ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static const struct dm_display_ops rk_mipi_dsi_ops = {
+ .read_timing = rk_mipi_read_timing,
+ .enable = rk_mipi_enable,
+};
+
+static const struct udevice_id rk_mipi_dsi_ids[] = {
+ { .compatible = "rockchip,rk3399_mipi_dsi" },
+ { }
+};
+
+U_BOOT_DRIVER(rk_mipi_dsi) = {
+ .name = "rk_mipi_dsi",
+ .id = UCLASS_DISPLAY,
+ .of_match = rk_mipi_dsi_ids,
+ .ofdata_to_platdata = rk_mipi_ofdata_to_platdata,
+ .probe = rk_mipi_probe,
+ .ops = &rk_mipi_dsi_ops,
+ .priv_auto_alloc_size = sizeof(struct rk_mipi_priv),
+};
diff --git a/drivers/video/rockchip/rk_vop.c b/drivers/video/rockchip/rk_vop.c
index aeecb58..2ea7954 100644
--- a/drivers/video/rockchip/rk_vop.c
+++ b/drivers/video/rockchip/rk_vop.c
@@ -109,6 +109,10 @@ void rkvop_mode_set(struct rk3288_vop *regs,
clrsetbits_le32(®s->sys_ctrl, M_ALL_OUT_EN,
V_HDMI_OUT_EN(1));
break;
+ case VOP_MODE_MIPI:
+ clrsetbits_le32(®s->sys_ctrl, M_ALL_OUT_EN,
+ V_MIPI_OUT_EN(1));
+ break;
case VOP_MODE_EDP:
default:
clrsetbits_le32(®s->sys_ctrl, M_ALL_OUT_EN,
@@ -178,13 +182,11 @@ void rkvop_mode_set(struct rk3288_vop *regs,
*
* @dev: VOP device that we want to connect to the display
* @fbbase: Frame buffer address
- * @l2bpp Log2 of bits-per-pixels for the display
* @ep_node: Device tree node to process - this is the offset of an endpoint
* node within the VOP's 'port' list.
* @return 0 if OK, -ve if something went wrong
*/
-int rk_display_init(struct udevice *dev, ulong fbbase,
- enum video_log2_bpp l2bpp, int ep_node)
+int rk_display_init(struct udevice *dev, ulong fbbase, int ep_node)
{
struct video_priv *uc_priv = dev_get_uclass_priv(dev);
const void *blob = gd->fdt_blob;
@@ -196,6 +198,7 @@ int rk_display_init(struct udevice *dev, ulong fbbase,
int ret, remote, i, offset;
struct display_plat *disp_uc_plat;
struct clk clk;
+ enum video_log2_bpp l2bpp;
vop_id = fdtdec_get_int(blob, ep_node, "reg", -1);
debug("vop_id=%d\n", vop_id);
@@ -245,11 +248,26 @@ int rk_display_init(struct udevice *dev, ulong fbbase,
ret = clk_get_by_index(dev, 1, &clk);
if (!ret)
ret = clk_set_rate(&clk, timing.pixelclock.typ);
- if (ret) {
+ /* clk_set_rate return clk rate,normally it is a none zero value */
+ if (!ret) {
debug("%s: Failed to set pixel clock: ret=%d\n", __func__, ret);
return ret;
}
+ /* Set bitwidth for vop display according to vop mode */
+ switch (vop_id) {
+ case VOP_MODE_EDP:
+ case VOP_MODE_HDMI:
+ case VOP_MODE_LVDS:
+ l2bpp = VIDEO_BPP16;
+ break;
+ case VOP_MODE_MIPI:
+ l2bpp = VIDEO_BPP32;
+ break;
+ default:
+ l2bpp = VIDEO_BPP16;
+ }
+
rkvop_mode_set(regs, &timing, vop_id);
rkvop_enable(regs, fbbase, 1 << l2bpp, &timing);
@@ -327,7 +345,7 @@ static int rk_vop_probe(struct udevice *dev)
for (node = fdt_first_subnode(blob, port);
node > 0;
node = fdt_next_subnode(blob, node)) {
- ret = rk_display_init(dev, plat->base, VIDEO_BPP16, node);
+ ret = rk_display_init(dev, plat->base, node);
if (ret)
debug("Device failed: ret=%d\n", ret);
if (!ret)
@@ -342,7 +360,13 @@ static int rk_vop_bind(struct udevice *dev)
{
struct video_uc_platdata *plat = dev_get_uclass_platdata(dev);
- plat->size = 1920 * 1080 * 2;
+/*
+ * plat->size is only used for reserve fb space in memory befor relocation.
+ * So we just need to make sure it's big enough for all condition. And
+ * actually, we now know nothing about the display port type, color depth
+ * and it's resolution ratio. So we can't calculate fb size accurately.
+ */
+ plat->size = 1920 * 1200 * 4;
return 0;
}
@@ -351,6 +375,8 @@ static const struct video_ops rk_vop_ops = {
};
static const struct udevice_id rk_vop_ids[] = {
+ { .compatible = "rockchip,rk3399-vop-big" },
+ { .compatible = "rockchip,rk3399-vop-lit" },
{ .compatible = "rockchip,rk3288-vop" },
{ }
};
--
1.9.1
More information about the U-Boot
mailing list