[U-Boot] [PATCH v3 2/6] ARM: dts: at91: Add dts files for at91sam9n12ek

Wenyou Yang wenyou.yang at atmel.com
Tue Apr 18 05:49:35 UTC 2017


The device tree source files of at91sam9n12ek boards are copied from
the Linux v4.10, do the changes as below.
 - Add the reg property for the pinctrl node.
 - Move the gpio (pioA, pioB, pioC, pioD) nodes as the pinctrl's
   slibling nodes, instead of the child nodes.
 - Change the compatible of the spi flash to "spi-flash".
 - Add the spi0 aliases.
 - Fix the pinctrl-names of mmc0 node.
 - Add the "u-boot,dm-pre-reloc" property to determine which nodes
   are used by the board_init_f stage.
 - Fix the compilation warnings.

Signed-off-by: Wenyou Yang <wenyou.yang at atmel.com>
Reviewed-by: Simon Glass <sjg at chromium.org>
---

Changes in v3: None
Changes in v2: None

 arch/arm/dts/Makefile          |    2 +
 arch/arm/dts/at91sam9n12.dtsi  | 1064 ++++++++++++++++++++++++++++++++++++++++
 arch/arm/dts/at91sam9n12ek.dts |  265 ++++++++++
 3 files changed, 1331 insertions(+)
 create mode 100644 arch/arm/dts/at91sam9n12.dtsi
 create mode 100644 arch/arm/dts/at91sam9n12ek.dts

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 3b1356b569..fb3e7e8217 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -353,6 +353,8 @@ dtb-$(CONFIG_TARGET_AT91SAM9X5EK) += \
 	at91sam9x25ek.dtb	\
 	at91sam9x35ek.dtb
 
+dtb-$(CONFIG_TARGET_AT91SAM9N12EK) += at91sam9n12ek.dtb
+
 dtb-$(CONFIG_TARGET_SAMA5D2_XPLAINED) += \
 	at91-sama5d2_xplained.dtb
 
diff --git a/arch/arm/dts/at91sam9n12.dtsi b/arch/arm/dts/at91sam9n12.dtsi
new file mode 100644
index 0000000000..7ba7116e8f
--- /dev/null
+++ b/arch/arm/dts/at91sam9n12.dtsi
@@ -0,0 +1,1064 @@
+/*
+ * at91sam9n12.dtsi - Device Tree include file for AT91SAM9N12 SoC
+ *
+ *  Copyright (C) 2012 Atmel,
+ *                2012 Hong Xu <hong.xu at atmel.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+#include "skeleton.dtsi"
+#include <dt-bindings/dma/at91.h>
+#include <dt-bindings/pinctrl/at91.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/at91.h>
+
+/ {
+	model = "Atmel AT91SAM9N12 SoC";
+	compatible = "atmel,at91sam9n12";
+	interrupt-parent = <&aic>;
+
+	aliases {
+		serial0 = &dbgu;
+		serial1 = &usart0;
+		serial2 = &usart1;
+		serial3 = &usart2;
+		serial4 = &usart3;
+		gpio0 = &pioA;
+		gpio1 = &pioB;
+		gpio2 = &pioC;
+		gpio3 = &pioD;
+		tcb0 = &tcb0;
+		tcb1 = &tcb1;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		ssc0 = &ssc0;
+		pwm0 = &pwm0;
+		spi0 = &spi0;
+	};
+	cpus {
+		#address-cells = <0>;
+		#size-cells = <0>;
+
+		cpu {
+			compatible = "arm,arm926ej-s";
+			device_type = "cpu";
+		};
+	};
+
+	memory {
+		reg = <0x20000000 0x10000000>;
+	};
+
+	clocks {
+		slow_xtal: slow_xtal {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <0>;
+		};
+
+		main_xtal: main_xtal {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <0>;
+		};
+	};
+
+	sram: sram at 00300000 {
+		compatible = "mmio-sram";
+		reg = <0x00300000 0x8000>;
+	};
+
+	ahb {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		u-boot,dm-pre-reloc;
+
+		apb {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			u-boot,dm-pre-reloc;
+
+			aic: interrupt-controller at fffff000 {
+				#interrupt-cells = <3>;
+				compatible = "atmel,at91rm9200-aic";
+				interrupt-controller;
+				reg = <0xfffff000 0x200>;
+				atmel,external-irqs = <31>;
+			};
+
+			ramc0: ramc at ffffe800 {
+				compatible = "atmel,at91sam9g45-ddramc";
+				reg = <0xffffe800 0x200>;
+				clocks = <&ddrck>;
+				clock-names = "ddrck";
+			};
+
+			pmc: pmc at fffffc00 {
+				compatible = "atmel,at91sam9n12-pmc", "syscon";
+				reg = <0xfffffc00 0x200>;
+				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+				interrupt-controller;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				#interrupt-cells = <1>;
+				u-boot,dm-pre-reloc;
+
+				main_rc_osc: main_rc_osc {
+					compatible = "atmel,at91sam9x5-clk-main-rc-osc";
+					#clock-cells = <0>;
+					interrupts-extended = <&pmc AT91_PMC_MOSCRCS>;
+					clock-frequency = <12000000>;
+					clock-accuracy = <50000000>;
+				};
+
+				main_osc: main_osc {
+					compatible = "atmel,at91rm9200-clk-main-osc";
+					#clock-cells = <0>;
+					interrupts-extended = <&pmc AT91_PMC_MOSCS>;
+					clocks = <&main_xtal>;
+				};
+
+				main: mainck {
+					compatible = "atmel,at91sam9x5-clk-main";
+					#clock-cells = <0>;
+					interrupts-extended = <&pmc AT91_PMC_MOSCSELS>;
+					clocks = <&main_rc_osc>, <&main_osc>;
+				};
+
+				plla: pllack at 0 {
+					compatible = "atmel,at91rm9200-clk-pll";
+					#clock-cells = <0>;
+					interrupts-extended = <&pmc AT91_PMC_LOCKA>;
+					clocks = <&main>;
+					reg = <0>;
+					atmel,clk-input-range = <2000000 32000000>;
+					#atmel,pll-clk-output-range-cells = <4>;
+					atmel,pll-clk-output-ranges = <745000000 800000000 0 0>,
+								      <695000000 750000000 1 0>,
+								      <645000000 700000000 2 0>,
+								      <595000000 650000000 3 0>,
+								      <545000000 600000000 0 1>,
+								      <495000000 555000000 1 1>,
+								      <445000000 500000000 2 1>,
+								      <400000000 450000000 3 1>;
+				};
+
+				plladiv: plladivck {
+					compatible = "atmel,at91sam9x5-clk-plldiv";
+					#clock-cells = <0>;
+					clocks = <&plla>;
+				};
+
+				pllb: pllbck at 1 {
+					compatible = "atmel,at91rm9200-clk-pll";
+					#clock-cells = <0>;
+					interrupts-extended = <&pmc AT91_PMC_LOCKB>;
+					clocks = <&main>;
+					reg = <1>;
+					atmel,clk-input-range = <2000000 32000000>;
+					#atmel,pll-clk-output-range-cells = <3>;
+					atmel,pll-clk-output-ranges = <30000000 100000000 0>;
+				};
+
+				mck: masterck {
+					compatible = "atmel,at91sam9x5-clk-master";
+					#clock-cells = <0>;
+					interrupts-extended = <&pmc AT91_PMC_MCKRDY>;
+					clocks = <&clk32k>, <&main>, <&plladiv>, <&pllb>;
+					atmel,clk-output-range = <0 133333333>;
+					atmel,clk-divisors = <1 2 4 3>;
+					atmel,master-clk-have-div3-pres;
+					u-boot,dm-pre-reloc;
+				};
+
+				usb: usbck {
+					compatible = "atmel,at91sam9n12-clk-usb";
+					#clock-cells = <0>;
+					clocks = <&pllb>;
+				};
+
+				prog: progck {
+					compatible = "atmel,at91sam9x5-clk-programmable";
+					#address-cells = <1>;
+					#size-cells = <0>;
+					interrupt-parent = <&pmc>;
+					clocks = <&clk32k>, <&main>, <&plladiv>, <&pllb>, <&mck>;
+
+					prog0: prog at 0 {
+						#clock-cells = <0>;
+						reg = <0>;
+						interrupts = <AT91_PMC_PCKRDY(0)>;
+					};
+
+					prog1: prog at 1 {
+						#clock-cells = <0>;
+						reg = <1>;
+						interrupts = <AT91_PMC_PCKRDY(1)>;
+					};
+				};
+
+				systemck {
+					compatible = "atmel,at91rm9200-clk-system";
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					ddrck: ddrck at 2 {
+						#clock-cells = <0>;
+						reg = <2>;
+						clocks = <&mck>;
+					};
+
+					lcdck: lcdck at 3 {
+						#clock-cells = <0>;
+						reg = <3>;
+						clocks = <&mck>;
+					};
+
+					uhpck: uhpck at 6 {
+						#clock-cells = <0>;
+						reg = <6>;
+						clocks = <&usb>;
+					};
+
+					udpck: udpck at 7 {
+						#clock-cells = <0>;
+						reg = <7>;
+						clocks = <&usb>;
+					};
+
+					pck0: pck0 at 8 {
+						#clock-cells = <0>;
+						reg = <8>;
+						clocks = <&prog0>;
+					};
+
+					pck1: pck1 at 9 {
+						#clock-cells = <0>;
+						reg = <9>;
+						clocks = <&prog1>;
+					};
+				};
+
+				periphck {
+					compatible = "atmel,at91sam9x5-clk-peripheral";
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&mck>;
+					u-boot,dm-pre-reloc;
+
+					pioAB_clk: pioAB_clk at 2 {
+						#clock-cells = <0>;
+						reg = <2>;
+						u-boot,dm-pre-reloc;
+					};
+
+					pioCD_clk: pioCD_clk at 3 {
+						#clock-cells = <0>;
+						reg = <3>;
+						u-boot,dm-pre-reloc;
+					};
+
+					fuse_clk: fuse_clk at 4 {
+						#clock-cells = <0>;
+						reg = <4>;
+					};
+
+					usart0_clk: usart0_clk at 5 {
+						#clock-cells = <0>;
+						reg = <5>;
+					};
+
+					usart1_clk: usart1_clk at 6 {
+						#clock-cells = <0>;
+						reg = <6>;
+					};
+
+					usart2_clk: usart2_clk at 7 {
+						#clock-cells = <0>;
+						reg = <7>;
+					};
+
+					usart3_clk: usart3_clk at 8 {
+						#clock-cells = <0>;
+						reg = <8>;
+					};
+
+					twi0_clk: twi0_clk at 9 {
+						reg = <9>;
+						#clock-cells = <0>;
+					};
+
+					twi1_clk: twi1_clk at 10 {
+						#clock-cells = <0>;
+						reg = <10>;
+					};
+
+					mci0_clk: mci0_clk at 12 {
+						#clock-cells = <0>;
+						reg = <12>;
+					};
+
+					spi0_clk: spi0_clk at 13 {
+						#clock-cells = <0>;
+						reg = <13>;
+					};
+
+					spi1_clk: spi1_clk at 14 {
+						#clock-cells = <0>;
+						reg = <14>;
+					};
+
+					uart0_clk: uart0_clk at 15 {
+						#clock-cells = <0>;
+						reg = <15>;
+					};
+
+					uart1_clk: uart1_clk at 16 {
+						#clock-cells = <0>;
+						reg = <16>;
+					};
+
+					tcb_clk: tcb_clk at 17 {
+						#clock-cells = <0>;
+						reg = <17>;
+					};
+
+					pwm_clk: pwm_clk at 18 {
+						#clock-cells = <0>;
+						reg = <18>;
+					};
+
+					adc_clk: adc_clk at 19 {
+						#clock-cells = <0>;
+						reg = <19>;
+					};
+
+					dma0_clk: dma0_clk at 20 {
+						#clock-cells = <0>;
+						reg = <20>;
+					};
+
+					uhphs_clk: uhphs_clk at 22 {
+						#clock-cells = <0>;
+						reg = <22>;
+					};
+
+					udphs_clk: udphs_clk at 23 {
+						#clock-cells = <0>;
+						reg = <23>;
+					};
+
+					lcdc_clk: lcdc_clk at 25 {
+						#clock-cells = <0>;
+						reg = <25>;
+					};
+
+					sha_clk: sha_clk at 27 {
+						#clock-cells = <0>;
+						reg = <27>;
+					};
+
+					ssc0_clk: ssc0_clk at 28 {
+						#clock-cells = <0>;
+						reg = <28>;
+					};
+
+					aes_clk: aes_clk at 29 {
+						#clock-cells = <0>;
+						reg = <29>;
+					};
+
+					trng_clk: trng_clk at 30 {
+						#clock-cells = <0>;
+						reg = <30>;
+					};
+				};
+			};
+
+			rstc at fffffe00 {
+				compatible = "atmel,at91sam9g45-rstc";
+				reg = <0xfffffe00 0x10>;
+				clocks = <&clk32k>;
+			};
+
+			pit: timer at fffffe30 {
+				compatible = "atmel,at91sam9260-pit";
+				reg = <0xfffffe30 0xf>;
+				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&mck>;
+			};
+
+			shdwc at fffffe10 {
+				compatible = "atmel,at91sam9x5-shdwc";
+				reg = <0xfffffe10 0x10>;
+				clocks = <&clk32k>;
+			};
+
+			sckc at fffffe50 {
+				compatible = "atmel,at91sam9x5-sckc";
+				reg = <0xfffffe50 0x4>;
+
+				slow_osc: slow_osc {
+					compatible = "atmel,at91sam9x5-clk-slow-osc";
+					#clock-cells = <0>;
+					clocks = <&slow_xtal>;
+				};
+
+				slow_rc_osc: slow_rc_osc {
+					compatible = "atmel,at91sam9x5-clk-slow-rc-osc";
+					#clock-cells = <0>;
+					clock-frequency = <32768>;
+					clock-accuracy = <50000000>;
+				};
+
+				clk32k: slck {
+					compatible = "atmel,at91sam9x5-clk-slow";
+					#clock-cells = <0>;
+					clocks = <&slow_rc_osc>, <&slow_osc>;
+				};
+			};
+
+			mmc0: mmc at f0008000 {
+				compatible = "atmel,hsmci";
+				reg = <0xf0008000 0x600>;
+				interrupts = <12 IRQ_TYPE_LEVEL_HIGH 0>;
+				dmas = <&dma 1 AT91_DMA_CFG_PER_ID(0)>;
+				dma-names = "rxtx";
+				clocks = <&mci0_clk>;
+				clock-names = "mci_clk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			tcb0: timer at f8008000 {
+				compatible = "atmel,at91sam9x5-tcb";
+				reg = <0xf8008000 0x100>;
+				interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>;
+				clocks = <&tcb_clk>, <&clk32k>;
+				clock-names = "t0_clk", "slow_clk";
+			};
+
+			tcb1: timer at f800c000 {
+				compatible = "atmel,at91sam9x5-tcb";
+				reg = <0xf800c000 0x100>;
+				interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>;
+				clocks = <&tcb_clk>, <&clk32k>;
+				clock-names = "t0_clk", "slow_clk";
+			};
+
+			hlcdc: hlcdc at f8038000 {
+				compatible = "atmel,at91sam9n12-hlcdc";
+				reg = <0xf8038000 0x2000>;
+				interrupts = <25 IRQ_TYPE_LEVEL_HIGH 0>;
+				clocks = <&lcdc_clk>, <&lcdck>, <&clk32k>;
+				clock-names = "periph_clk", "sys_clk", "slow_clk";
+				status = "disabled";
+
+				hlcdc-display-controller {
+					compatible = "atmel,hlcdc-display-controller";
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port at 0 {
+						#address-cells = <1>;
+						#size-cells = <0>;
+						reg = <0>;
+					};
+				};
+
+				hlcdc_pwm: hlcdc-pwm {
+					compatible = "atmel,hlcdc-pwm";
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_lcd_pwm>;
+					#pwm-cells = <3>;
+				};
+			};
+
+			dma: dma-controller at ffffec00 {
+				compatible = "atmel,at91sam9g45-dma";
+				reg = <0xffffec00 0x200>;
+				interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>;
+				#dma-cells = <2>;
+				clocks = <&dma0_clk>;
+				clock-names = "dma_clk";
+			};
+
+			pinctrl at fffff400 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "atmel,at91sam9x5-pinctrl", "atmel,at91rm9200-pinctrl", "simple-bus";
+				ranges = <0xfffff400 0xfffff400 0x800>;
+				reg = <0xfffff400 0x200
+				       0xfffff600 0x200
+				       0xfffff800 0x200
+				       0xfffffa00 0x200
+				      >;
+
+				atmel,mux-mask = <
+				      /*    A         B          C     */
+				       0xffffffff 0xffe07983 0x00000000  /* pioA */
+				       0x00040000 0x00047e0f 0x00000000  /* pioB */
+				       0xfdffffff 0x07c00000 0xb83fffff  /* pioC */
+				       0x003fffff 0x003f8000 0x00000000  /* pioD */
+				      >;
+				u-boot,dm-pre-reloc;
+
+				/* shared pinctrl settings */
+				dbgu {
+					u-boot,dm-pre-reloc;
+					pinctrl_dbgu: dbgu-0 {
+						atmel,pins =
+							<AT91_PIOA 9 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+							 AT91_PIOA 10 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+					};
+				};
+
+				lcd {
+					pinctrl_lcd_base: lcd-base-0 {
+						atmel,pins =
+							<AT91_PIOC 27 AT91_PERIPH_A AT91_PINCTRL_NONE	/* LCDVSYNC */
+							 AT91_PIOC 28 AT91_PERIPH_A AT91_PINCTRL_NONE	/* LCDHSYNC */
+							 AT91_PIOC 24 AT91_PERIPH_A AT91_PINCTRL_NONE	/* LCDDISP */
+							 AT91_PIOC 29 AT91_PERIPH_A AT91_PINCTRL_NONE	/* LCDDEN */
+							 AT91_PIOC 30 AT91_PERIPH_A AT91_PINCTRL_NONE>;	/* LCDPCK */
+					};
+
+					pinctrl_lcd_pwm: lcd-pwm-0 {
+						atmel,pins = <AT91_PIOC 26 AT91_PERIPH_A AT91_PINCTRL_NONE>;	/* LCDPWM */
+					};
+
+					pinctrl_lcd_rgb888: lcd-rgb-3 {
+						atmel,pins =
+							<AT91_PIOC 0 AT91_PERIPH_A AT91_PINCTRL_NONE	/* LCDD0 pin */
+							 AT91_PIOC 1 AT91_PERIPH_A AT91_PINCTRL_NONE	/* LCDD1 pin */
+							 AT91_PIOC 2 AT91_PERIPH_A AT91_PINCTRL_NONE	/* LCDD2 pin */
+							 AT91_PIOC 3 AT91_PERIPH_A AT91_PINCTRL_NONE	/* LCDD3 pin */
+							 AT91_PIOC 4 AT91_PERIPH_A AT91_PINCTRL_NONE	/* LCDD4 pin */
+							 AT91_PIOC 5 AT91_PERIPH_A AT91_PINCTRL_NONE	/* LCDD5 pin */
+							 AT91_PIOC 6 AT91_PERIPH_A AT91_PINCTRL_NONE	/* LCDD6 pin */
+							 AT91_PIOC 7 AT91_PERIPH_A AT91_PINCTRL_NONE	/* LCDD7 pin */
+							 AT91_PIOC 8 AT91_PERIPH_A AT91_PINCTRL_NONE	/* LCDD8 pin */
+							 AT91_PIOC 9 AT91_PERIPH_A AT91_PINCTRL_NONE	/* LCDD9 pin */
+							 AT91_PIOC 10 AT91_PERIPH_A AT91_PINCTRL_NONE	/* LCDD10 pin */
+							 AT91_PIOC 11 AT91_PERIPH_A AT91_PINCTRL_NONE	/* LCDD11 pin */
+							 AT91_PIOC 12 AT91_PERIPH_A AT91_PINCTRL_NONE	/* LCDD12 pin */
+							 AT91_PIOC 13 AT91_PERIPH_A AT91_PINCTRL_NONE	/* LCDD13 pin */
+							 AT91_PIOC 14 AT91_PERIPH_A AT91_PINCTRL_NONE	/* LCDD14 pin */
+							 AT91_PIOC 15 AT91_PERIPH_A AT91_PINCTRL_NONE	/* LCDD15 pin */
+							 AT91_PIOC 16 AT91_PERIPH_A AT91_PINCTRL_NONE	/* LCDD16 pin */
+							 AT91_PIOC 17 AT91_PERIPH_A AT91_PINCTRL_NONE	/* LCDD17 pin */
+							 AT91_PIOC 18 AT91_PERIPH_A AT91_PINCTRL_NONE	/* LCDD18 pin */
+							 AT91_PIOC 19 AT91_PERIPH_A AT91_PINCTRL_NONE	/* LCDD19 pin */
+							 AT91_PIOC 20 AT91_PERIPH_A AT91_PINCTRL_NONE	/* LCDD20 pin */
+							 AT91_PIOC 21 AT91_PERIPH_A AT91_PINCTRL_NONE	/* LCDD21 pin */
+							 AT91_PIOC 22 AT91_PERIPH_A AT91_PINCTRL_NONE	/* LCDD22 pin */
+							 AT91_PIOC 23 AT91_PERIPH_A AT91_PINCTRL_NONE>;	/* LCDD23 pin */
+					};
+				};
+
+				usart0 {
+					pinctrl_usart0: usart0-0 {
+						atmel,pins =
+							<AT91_PIOA 1 AT91_PERIPH_A AT91_PINCTRL_PULL_UP	/* PA1 periph A with pullup */
+							 AT91_PIOA 0 AT91_PERIPH_A AT91_PINCTRL_NONE>;	/* PA0 periph A */
+					};
+
+					pinctrl_usart0_rts: usart0_rts-0 {
+						atmel,pins =
+							<AT91_PIOA 2 AT91_PERIPH_A AT91_PINCTRL_NONE>;	/* PA2 periph A */
+					};
+
+					pinctrl_usart0_cts: usart0_cts-0 {
+						atmel,pins =
+							<AT91_PIOA 3 AT91_PERIPH_A AT91_PINCTRL_NONE>;	/* PA3 periph A */
+					};
+				};
+
+				usart1 {
+					pinctrl_usart1: usart1-0 {
+						atmel,pins =
+							<AT91_PIOA 6 AT91_PERIPH_A AT91_PINCTRL_PULL_UP	/* PA6 periph A with pullup */
+							 AT91_PIOA 5 AT91_PERIPH_A AT91_PINCTRL_NONE>;	/* PA5 periph A */
+					};
+				};
+
+				usart2 {
+					pinctrl_usart2: usart2-0 {
+						atmel,pins =
+							<AT91_PIOA 8 AT91_PERIPH_A AT91_PINCTRL_PULL_UP	/* PA8 periph A with pullup */
+							 AT91_PIOA 7 AT91_PERIPH_A AT91_PINCTRL_NONE>;	/* PA7 periph A */
+					};
+
+					pinctrl_usart2_rts: usart2_rts-0 {
+						atmel,pins =
+							<AT91_PIOB 0 AT91_PERIPH_B AT91_PINCTRL_NONE>;	/* PB0 periph B */
+					};
+
+					pinctrl_usart2_cts: usart2_cts-0 {
+						atmel,pins =
+							<AT91_PIOB 1 AT91_PERIPH_B AT91_PINCTRL_NONE>;	/* PB1 periph B */
+					};
+				};
+
+				usart3 {
+					pinctrl_usart3: usart3-0 {
+						atmel,pins =
+							<AT91_PIOC 23 AT91_PERIPH_B AT91_PINCTRL_PULL_UP	/* PC23 periph B with pullup */
+							 AT91_PIOC 22 AT91_PERIPH_B AT91_PINCTRL_NONE>;	/* PC22 periph B */
+					};
+
+					pinctrl_usart3_rts: usart3_rts-0 {
+						atmel,pins =
+							<AT91_PIOC 24 AT91_PERIPH_B AT91_PINCTRL_NONE>;	/* PC24 periph B */
+					};
+
+					pinctrl_usart3_cts: usart3_cts-0 {
+						atmel,pins =
+							<AT91_PIOC 25 AT91_PERIPH_B AT91_PINCTRL_NONE>;	/* PC25 periph B */
+					};
+				};
+
+				uart0 {
+					pinctrl_uart0: uart0-0 {
+						atmel,pins =
+							<AT91_PIOC 9 AT91_PERIPH_C AT91_PINCTRL_PULL_UP	/* PC9 periph C with pullup */
+							 AT91_PIOC 8 AT91_PERIPH_C AT91_PINCTRL_NONE>;	/* PC8 periph C */
+					};
+				};
+
+				uart1 {
+					pinctrl_uart1: uart1-0 {
+						atmel,pins =
+							<AT91_PIOC 16 AT91_PERIPH_C AT91_PINCTRL_PULL_UP	/* PC17 periph C with pullup */
+							 AT91_PIOC 17 AT91_PERIPH_C AT91_PINCTRL_NONE>;	/* PC16 periph C */
+					};
+				};
+
+				nand {
+					pinctrl_nand: nand-0 {
+						atmel,pins =
+							<AT91_PIOD 5 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP	/* PD5 gpio RDY pin pull_up*/
+							 AT91_PIOD 4 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;	/* PD4 gpio enable pin pull_up */
+					};
+				};
+
+				mmc0 {
+					pinctrl_mmc0_slot0_clk_cmd_dat0: mmc0_slot0_clk_cmd_dat0-0 {
+						atmel,pins =
+							<AT91_PIOA 17 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PA17 periph A */
+							 AT91_PIOA 16 AT91_PERIPH_A AT91_PINCTRL_PULL_UP	/* PA16 periph A with pullup */
+							 AT91_PIOA 15 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;	/* PA15 periph A with pullup */
+					};
+
+					pinctrl_mmc0_slot0_dat1_3: mmc0_slot0_dat1_3-0 {
+						atmel,pins =
+							<AT91_PIOA 18 AT91_PERIPH_A AT91_PINCTRL_PULL_UP	/* PA18 periph A with pullup */
+							 AT91_PIOA 19 AT91_PERIPH_A AT91_PINCTRL_PULL_UP	/* PA19 periph A with pullup */
+							 AT91_PIOA 20 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;	/* PA20 periph A with pullup */
+					};
+
+					pinctrl_mmc0_slot0_dat4_7: mmc0_slot0_dat4_7-0 {
+						atmel,pins =
+							<AT91_PIOA 11 AT91_PERIPH_B AT91_PINCTRL_PULL_UP	/* PA11 periph B with pullup */
+							 AT91_PIOA 12 AT91_PERIPH_B AT91_PINCTRL_PULL_UP	/* PA12 periph B with pullup */
+							 AT91_PIOA 13 AT91_PERIPH_B AT91_PINCTRL_PULL_UP	/* PA13 periph B with pullup */
+							 AT91_PIOA 14 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>;	/* PA14 periph B with pullup */
+					};
+				};
+
+				ssc0 {
+					pinctrl_ssc0_tx: ssc0_tx-0 {
+						atmel,pins =
+							<AT91_PIOA 24 AT91_PERIPH_B AT91_PINCTRL_NONE	/* PA24 periph B */
+							 AT91_PIOA 25 AT91_PERIPH_B AT91_PINCTRL_NONE	/* PA25 periph B */
+							 AT91_PIOA 26 AT91_PERIPH_B AT91_PINCTRL_NONE>;	/* PA26 periph B */
+					};
+
+					pinctrl_ssc0_rx: ssc0_rx-0 {
+						atmel,pins =
+							<AT91_PIOA 27 AT91_PERIPH_B AT91_PINCTRL_NONE	/* PA27 periph B */
+							 AT91_PIOA 28 AT91_PERIPH_B AT91_PINCTRL_NONE	/* PA28 periph B */
+							 AT91_PIOA 29 AT91_PERIPH_B AT91_PINCTRL_NONE>;	/* PA29 periph B */
+					};
+				};
+
+				spi0 {
+					pinctrl_spi0: spi0-0 {
+						atmel,pins =
+							<AT91_PIOA 11 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PA11 periph A SPI0_MISO pin */
+							 AT91_PIOA 12 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PA12 periph A SPI0_MOSI pin */
+							 AT91_PIOA 13 AT91_PERIPH_A AT91_PINCTRL_NONE>;	/* PA13 periph A SPI0_SPCK pin */
+					};
+				};
+
+				spi1 {
+					pinctrl_spi1: spi1-0 {
+						atmel,pins =
+							<AT91_PIOA 21 AT91_PERIPH_B AT91_PINCTRL_NONE	/* PA21 periph B SPI1_MISO pin */
+							 AT91_PIOA 22 AT91_PERIPH_B AT91_PINCTRL_NONE	/* PA22 periph B SPI1_MOSI pin */
+							 AT91_PIOA 23 AT91_PERIPH_B AT91_PINCTRL_NONE>;	/* PA23 periph B SPI1_SPCK pin */
+					};
+				};
+
+				i2c0 {
+					pinctrl_i2c0: i2c0-0 {
+						atmel,pins =
+							<AT91_PIOA 30 AT91_PERIPH_A AT91_PINCTRL_NONE
+							 AT91_PIOA 31 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+					};
+				};
+
+				i2c1 {
+					pinctrl_i2c1: i2c1-0 {
+						atmel,pins =
+							<AT91_PIOC 0 AT91_PERIPH_C AT91_PINCTRL_NONE
+							 AT91_PIOC 1 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+					};
+				};
+
+				tcb0 {
+					pinctrl_tcb0_tclk0: tcb0_tclk0-0 {
+						atmel,pins = <AT91_PIOA 24 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_tcb0_tclk1: tcb0_tclk1-0 {
+						atmel,pins = <AT91_PIOA 25 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_tcb0_tclk2: tcb0_tclk2-0 {
+						atmel,pins = <AT91_PIOA 26 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_tcb0_tioa0: tcb0_tioa0-0 {
+						atmel,pins = <AT91_PIOA 21 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_tcb0_tioa1: tcb0_tioa1-0 {
+						atmel,pins = <AT91_PIOA 22 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_tcb0_tioa2: tcb0_tioa2-0 {
+						atmel,pins = <AT91_PIOA 23 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_tcb0_tiob0: tcb0_tiob0-0 {
+						atmel,pins = <AT91_PIOA 27 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_tcb0_tiob1: tcb0_tiob1-0 {
+						atmel,pins = <AT91_PIOA 28 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_tcb0_tiob2: tcb0_tiob2-0 {
+						atmel,pins = <AT91_PIOA 29 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+					};
+				};
+
+				tcb1 {
+					pinctrl_tcb1_tclk0: tcb1_tclk0-0 {
+						atmel,pins = <AT91_PIOC 4 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_tcb1_tclk1: tcb1_tclk1-0 {
+						atmel,pins = <AT91_PIOC 7 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_tcb1_tclk2: tcb1_tclk2-0 {
+						atmel,pins = <AT91_PIOC 14 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_tcb1_tioa0: tcb1_tioa0-0 {
+						atmel,pins = <AT91_PIOC 2 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_tcb1_tioa1: tcb1_tioa1-0 {
+						atmel,pins = <AT91_PIOC 5 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_tcb1_tioa2: tcb1_tioa2-0 {
+						atmel,pins = <AT91_PIOC 12 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_tcb1_tiob0: tcb1_tiob0-0 {
+						atmel,pins = <AT91_PIOC 3 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_tcb1_tiob1: tcb1_tiob1-0 {
+						atmel,pins = <AT91_PIOC 6 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_tcb1_tiob2: tcb1_tiob2-0 {
+						atmel,pins = <AT91_PIOC 13 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+					};
+				};
+			};
+
+			pioA: gpio at fffff400 {
+				compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+				reg = <0xfffff400 0x200>;
+				interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
+				#gpio-cells = <2>;
+				gpio-controller;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				clocks = <&pioAB_clk>;
+				u-boot,dm-pre-reloc;
+			};
+
+			pioB: gpio at fffff600 {
+				compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+				reg = <0xfffff600 0x200>;
+				interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
+				#gpio-cells = <2>;
+				gpio-controller;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				clocks = <&pioAB_clk>;
+				u-boot,dm-pre-reloc;
+			};
+
+			pioC: gpio at fffff800 {
+				compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+				reg = <0xfffff800 0x200>;
+				interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
+				#gpio-cells = <2>;
+				gpio-controller;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				clocks = <&pioCD_clk>;
+				u-boot,dm-pre-reloc;
+			};
+
+			pioD: gpio at fffffa00 {
+				compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+				reg = <0xfffffa00 0x200>;
+				interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
+				#gpio-cells = <2>;
+				gpio-controller;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				clocks = <&pioCD_clk>;
+				u-boot,dm-pre-reloc;
+			};
+
+			dbgu: serial at fffff200 {
+				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+				reg = <0xfffff200 0x200>;
+				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_dbgu>;
+				clocks = <&mck>;
+				clock-names = "usart";
+				status = "disabled";
+			};
+
+			ssc0: ssc at f0010000 {
+				compatible = "atmel,at91sam9g45-ssc";
+				reg = <0xf0010000 0x4000>;
+				interrupts = <28 IRQ_TYPE_LEVEL_HIGH 5>;
+				dmas = <&dma 0 AT91_DMA_CFG_PER_ID(21)>,
+				       <&dma 0 AT91_DMA_CFG_PER_ID(22)>;
+				dma-names = "tx", "rx";
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
+				clocks = <&ssc0_clk>;
+				clock-names = "pclk";
+				status = "disabled";
+			};
+
+			usart0: serial at f801c000 {
+				compatible = "atmel,at91sam9260-usart";
+				reg = <0xf801c000 0x4000>;
+				interrupts = <5 IRQ_TYPE_LEVEL_HIGH 5>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_usart0>;
+				clocks = <&usart0_clk>;
+				clock-names = "usart";
+				status = "disabled";
+			};
+
+			usart1: serial at f8020000 {
+				compatible = "atmel,at91sam9260-usart";
+				reg = <0xf8020000 0x4000>;
+				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_usart1>;
+				clocks = <&usart1_clk>;
+				clock-names = "usart";
+				status = "disabled";
+			};
+
+			usart2: serial at f8024000 {
+				compatible = "atmel,at91sam9260-usart";
+				reg = <0xf8024000 0x4000>;
+				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_usart2>;
+				clocks = <&usart2_clk>;
+				clock-names = "usart";
+				status = "disabled";
+			};
+
+			usart3: serial at f8028000 {
+				compatible = "atmel,at91sam9260-usart";
+				reg = <0xf8028000 0x4000>;
+				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_usart3>;
+				clocks = <&usart3_clk>;
+				clock-names = "usart";
+				status = "disabled";
+			};
+
+			i2c0: i2c at f8010000 {
+				compatible = "atmel,at91sam9x5-i2c";
+				reg = <0xf8010000 0x100>;
+				interrupts = <9 IRQ_TYPE_LEVEL_HIGH 6>;
+				dmas = <&dma 1 AT91_DMA_CFG_PER_ID(13)>,
+				       <&dma 1 AT91_DMA_CFG_PER_ID(14)>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c0>;
+				clocks = <&twi0_clk>;
+				status = "disabled";
+			};
+
+			i2c1: i2c at f8014000 {
+				compatible = "atmel,at91sam9x5-i2c";
+				reg = <0xf8014000 0x100>;
+				interrupts = <10 IRQ_TYPE_LEVEL_HIGH 6>;
+				dmas = <&dma 1 AT91_DMA_CFG_PER_ID(15)>,
+				       <&dma 1 AT91_DMA_CFG_PER_ID(16)>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c1>;
+				clocks = <&twi1_clk>;
+				status = "disabled";
+			};
+
+			spi0: spi at f0000000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "atmel,at91rm9200-spi";
+				reg = <0xf0000000 0x100>;
+				interrupts = <13 IRQ_TYPE_LEVEL_HIGH 3>;
+				dmas = <&dma 1 AT91_DMA_CFG_PER_ID(1)>,
+				       <&dma 1 AT91_DMA_CFG_PER_ID(2)>;
+				dma-names = "tx", "rx";
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_spi0>;
+				clocks = <&spi0_clk>;
+				clock-names = "spi_clk";
+				status = "disabled";
+			};
+
+			spi1: spi at f0004000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "atmel,at91rm9200-spi";
+				reg = <0xf0004000 0x100>;
+				interrupts = <14 IRQ_TYPE_LEVEL_HIGH 3>;
+				dmas = <&dma 1 AT91_DMA_CFG_PER_ID(3)>,
+				       <&dma 1 AT91_DMA_CFG_PER_ID(4)>;
+				dma-names = "tx", "rx";
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_spi1>;
+				clocks = <&spi1_clk>;
+				clock-names = "spi_clk";
+				status = "disabled";
+			};
+
+			watchdog at fffffe40 {
+				compatible = "atmel,at91sam9260-wdt";
+				reg = <0xfffffe40 0x10>;
+				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&clk32k>;
+				atmel,watchdog-type = "hardware";
+				atmel,reset-type = "all";
+				atmel,dbg-halt;
+				status = "disabled";
+			};
+
+			rtc at fffffeb0 {
+				compatible = "atmel,at91rm9200-rtc";
+				reg = <0xfffffeb0 0x40>;
+				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&clk32k>;
+				status = "disabled";
+			};
+
+			pwm0: pwm at f8034000 {
+				compatible = "atmel,at91sam9rl-pwm";
+				reg = <0xf8034000 0x300>;
+				interrupts = <18 IRQ_TYPE_LEVEL_HIGH 4>;
+				#pwm-cells = <3>;
+				clocks = <&pwm_clk>;
+				status = "disabled";
+			};
+
+			usb1: gadget at f803c000 {
+				compatible = "atmel,at91sam9260-udc";
+				reg = <0xf803c000 0x4000>;
+				interrupts = <23 IRQ_TYPE_LEVEL_HIGH 2>;
+				clocks = <&udphs_clk>, <&udpck>;
+				clock-names = "pclk", "hclk";
+				status = "disabled";
+			};
+		};
+
+		nand0: nand at 40000000 {
+			compatible = "atmel,at91rm9200-nand";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = < 0x40000000 0x10000000
+				0xffffe000 0x00000600
+				0xffffe600 0x00000200
+				0x00108000 0x00018000
+			       >;
+			atmel,pmecc-lookup-table-offset = <0x0 0x8000>;
+			atmel,nand-addr-offset = <21>;
+			atmel,nand-cmd-offset = <22>;
+			atmel,nand-has-dma;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_nand>;
+			gpios = <&pioD 5 GPIO_ACTIVE_HIGH
+				 &pioD 4 GPIO_ACTIVE_HIGH
+				 0
+				>;
+			status = "disabled";
+		};
+
+		usb0: ohci at 00500000 {
+			compatible = "atmel,at91rm9200-ohci", "usb-ohci";
+			reg = <0x00500000 0x00100000>;
+			interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
+			clocks = <&uhphs_clk>, <&uhphs_clk>, <&uhpck>;
+			clock-names = "ohci_clk", "hclk", "uhpck";
+			status = "disabled";
+		};
+	};
+
+	i2c-gpio-0 {
+		compatible = "i2c-gpio";
+		gpios = <&pioA 30 GPIO_ACTIVE_HIGH /* sda */
+			 &pioA 31 GPIO_ACTIVE_HIGH /* scl */
+			>;
+		i2c-gpio,sda-open-drain;
+		i2c-gpio,scl-open-drain;
+		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
+};
diff --git a/arch/arm/dts/at91sam9n12ek.dts b/arch/arm/dts/at91sam9n12ek.dts
new file mode 100644
index 0000000000..888bda15aa
--- /dev/null
+++ b/arch/arm/dts/at91sam9n12ek.dts
@@ -0,0 +1,265 @@
+/*
+ * at91sam9n12ek.dts - Device Tree file for AT91SAM9N12-EK board
+ *
+ *  Copyright (C) 2012 Atmel,
+ *                2012 Hong Xu <hong.xu at atmel.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include "at91sam9n12.dtsi"
+
+/ {
+	model = "Atmel AT91SAM9N12-EK";
+	compatible = "atmel,at91sam9n12ek", "atmel,at91sam9n12", "atmel,at91sam9";
+
+	chosen {
+		bootargs = "root=/dev/mtdblock1 rw rootfstype=jffs2";
+		stdout-path = "serial0:115200n8";
+		u-boot,dm-pre-reloc;
+	};
+
+	memory {
+		reg = <0x20000000 0x8000000>;
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <16000000>;
+		};
+	};
+
+	ahb {
+		apb {
+			dbgu: serial at fffff200 {
+				u-boot,dm-pre-reloc;
+				status = "okay";
+			};
+
+			ssc0: ssc at f0010000 {
+				status = "okay";
+			};
+
+			i2c0: i2c at f8010000 {
+				status = "okay";
+
+				wm8904: codec at 1a {
+					compatible = "wlf,wm8904";
+					reg = <0x1a>;
+					clocks = <&pck0>;
+					clock-names = "mclk";
+				};
+
+				qt1070: keyboard at 1b {
+					compatible = "qt1070";
+					reg = <0x1b>;
+					interrupt-parent = <&pioA>;
+					interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_qt1070_irq>;
+				};
+			};
+
+			mmc0: mmc at f0008000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <
+					&pinctrl_board_mmc0
+					&pinctrl_mmc0_slot0_clk_cmd_dat0
+					&pinctrl_mmc0_slot0_dat1_3>;
+				status = "okay";
+				slot at 0 {
+					reg = <0>;
+					bus-width = <4>;
+					cd-gpios = <&pioA 7 GPIO_ACTIVE_HIGH>;
+				};
+			};
+
+			pinctrl at fffff400 {
+				mmc0 {
+					pinctrl_board_mmc0: mmc0-board {
+						atmel,pins =
+							<AT91_PIOA 7 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;	/* PA7 gpio CD pin pull up and deglitch */
+					};
+				};
+
+				qt1070 {
+					pinctrl_qt1070_irq: qt1070_irq {
+						atmel,pins =
+							<AT91_PIOA 2 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+					};
+				};
+
+				sound {
+					pinctrl_pck0_as_audio_mck: pck0_as_audio_mck {
+						atmel,pins =
+							<AT91_PIOB 10 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+					};
+				};
+
+				usb1 {
+					pinctrl_usb1_vbus_sense: usb1_vbus_sense {
+						atmel,pins =
+							<AT91_PIOB 16 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;	/* PB16 gpio usb vbus sense, no pull up and deglitch */
+					};
+				};
+			};
+
+			spi0: spi at f0000000 {
+				status = "okay";
+				cs-gpios = <&pioA 14 0>, <0>, <0>, <0>;
+				spi_flash at 0 {
+					compatible = "spi-flash";
+					spi-max-frequency = <50000000>;
+					reg = <0>;
+				};
+			};
+
+			hlcdc: hlcdc at f8038000 {
+				status = "okay";
+
+				hlcdc-display-controller {
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_lcd_base &pinctrl_lcd_rgb888>;
+
+					port at 0 {
+						hlcdc_panel_output: endpoint at 0 {
+							reg = <0>;
+							remote-endpoint = <&panel_input>;
+						};
+					};
+				};
+			};
+
+			usb1: gadget at f803c000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_usb1_vbus_sense>;
+				atmel,vbus-gpio = <&pioB 16 GPIO_ACTIVE_HIGH>;
+				status = "okay";
+			};
+
+			watchdog at fffffe40 {
+				status = "okay";
+			};
+
+			rtc at fffffeb0 {
+				status = "okay";
+			};
+		};
+
+		nand0: nand at 40000000 {
+			nand-bus-width = <8>;
+			nand-ecc-mode = "hw";
+			atmel,has-pmecc;
+			atmel,pmecc-cap = <2>;
+			atmel,pmecc-sector-size = <512>;
+			nand-on-flash-bbt;
+			status = "okay";
+		};
+
+		usb0: ohci at 00500000 {
+			num-ports = <1>;
+			atmel,vbus-gpio = <&pioB 7 GPIO_ACTIVE_LOW>;
+			status = "okay";
+		};
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&hlcdc_pwm 0 50000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+		power-supply = <&bl_reg>;
+		status = "okay";
+	};
+
+	bl_reg: backlight_regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "backlight-power-supply";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		status = "okay";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		d8 {
+			label = "d8";
+			gpios = <&pioB 4 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "mmc0";
+		};
+
+		d9 {
+			label = "d9";
+			gpios = <&pioB 5 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "nand-disk";
+		};
+
+		d10 {
+			label = "d10";
+			gpios = <&pioB 6 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		enter {
+			label = "Enter";
+			gpios = <&pioB 3 GPIO_ACTIVE_LOW>;
+			linux,code = <28>;
+			wakeup-source;
+		};
+	};
+
+	panel: panel {
+		compatible = "qiaodian,qd43003c0-40", "simple-panel";
+		backlight = <&backlight>;
+		power-supply = <&panel_reg>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+
+		port at 0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			panel_input: endpoint at 0 {
+				reg = <0>;
+				remote-endpoint = <&hlcdc_panel_output>;
+			};
+		};
+	};
+
+	panel_reg: panel_regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "panel-power-supply";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		status = "okay";
+	};
+
+	sound {
+		compatible = "atmel,asoc-wm8904";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pck0_as_audio_mck>;
+
+		atmel,model = "wm8904 @ AT91SAM9N12";
+		atmel,audio-routing =
+			"Headphone Jack", "HPOUTL",
+			"Headphone Jack", "HPOUTR",
+			"IN2L", "Line In Jack",
+			"IN2R", "Line In Jack",
+			"Mic", "MICBIAS",
+			"IN1L", "Mic";
+
+		atmel,ssc-controller = <&ssc0>;
+		atmel,audio-codec = <&wm8904>;
+	};
+};
-- 
2.11.0



More information about the U-Boot mailing list