[U-Boot] [PATCH][v2] board: ls2080ardb, ls2080aqds: Adjust memory map for NOR-boot
Santan Kumar
santan.kumar at nxp.com
Fri Apr 28 07:17:24 UTC 2017
This patch adjusts memory map for images on LS2080ARDB,
LS2080AQDS as per below memory map for NOR flash:
Image Flash Offset
RCW+PBI 0x00000000
Boot firmware (U-Boot) 0x00100000
Boot firmware Environment 0x00300000
PPA firmware 0x00400000
PHY firmware 0x00980000
DPAA2 MC 0x00A00000
DPAA2 DPL 0x00D00000
DPAA2 DPC 0x00E00000
Kernel.itb 0x01000000
Signed-off-by: Santan Kumar <santan.kumar at nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain at nxp.com>
---
Changes for v2:
1. Rebase on the top of Priyanka's QSPI patch
https://patchwork.ozlabs.org/patch/756222/
arch/arm/cpu/armv8/fsl-layerscape/Kconfig | 2 +-
board/freescale/ls2080aqds/README | 12 ++++++++++++
board/freescale/ls2080ardb/README | 13 +++++++++++++
include/configs/ls2080a_common.h | 8 ++++----
include/configs/ls2080aqds.h | 8 ++++----
include/configs/ls2080ardb.h | 12 ++++++------
6 files changed, 40 insertions(+), 15 deletions(-)
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/Kconfig b/arch/arm/cpu/armv8/fsl-layerscape/Kconfig
index d0770c0..4d82257 100644
--- a/arch/arm/cpu/armv8/fsl-layerscape/Kconfig
+++ b/arch/arm/cpu/armv8/fsl-layerscape/Kconfig
@@ -162,7 +162,7 @@ config SYS_LS_PPA_FW_ADDR
depends on FSL_LS_PPA
default 0x20400000 if SYS_LS_PPA_FW_IN_XIP && QSPI_BOOT && ARCH_LS2080A
default 0x40500000 if SYS_LS_PPA_FW_IN_XIP && QSPI_BOOT
- default 0x580a00000 if SYS_LS_PPA_FW_IN_XIP && ARCH_LS2080A
+ default 0x580400000 if SYS_LS_PPA_FW_IN_XIP && ARCH_LS2080A
default 0x60500000 if SYS_LS_PPA_FW_IN_XIP
default 0x500000 if SYS_LS_PPA_FW_IN_MMC
default 0x500000 if SYS_LS_PPA_FW_IN_NAND
diff --git a/board/freescale/ls2080aqds/README b/board/freescale/ls2080aqds/README
index 2808bd5..fd0e25a 100644
--- a/board/freescale/ls2080aqds/README
+++ b/board/freescale/ls2080aqds/README
@@ -89,6 +89,18 @@ c) NAND boot
d) SD boot
e) QSPI boot
+Memory map for NOR boot
+-------------------------
+Image Flash Offset
+RCW+PBI 0x00000000
+Boot firmware (U-Boot) 0x00100000
+Boot firmware Environment 0x00300000
+PPA firmware 0x00400000
+DPAA2 MC 0x00A00000
+DPAA2 DPL 0x00D00000
+DPAA2 DPC 0x00E00000
+Kernel.itb 0x01000000
+
Environment Variables
---------------------
- mcboottimeout: MC boot timeout in milliseconds. If this variable is not defined
diff --git a/board/freescale/ls2080ardb/README b/board/freescale/ls2080ardb/README
index 873aadf..0003b45 100644
--- a/board/freescale/ls2080ardb/README
+++ b/board/freescale/ls2080ardb/README
@@ -71,6 +71,19 @@ a) NOR boot
b) NAND boot
c) QSPI boot
+Memory map for NOR boot
+-------------------------
+Image Flash Offset
+RCW+PBI 0x00000000
+Boot firmware (U-Boot) 0x00100000
+Boot firmware Environment 0x00300000
+PPA firmware 0x00400000
+Cortina PHY firmware 0x00980000
+DPAA2 MC 0x00A00000
+DPAA2 DPL 0x00D00000
+DPAA2 DPC 0x00E00000
+Kernel.itb 0x01000000
+
cfg_rcw_src switches needs to be changed for booting from different option.
Refer to board documentation for correct switch setting.
diff --git a/include/configs/ls2080a_common.h b/include/configs/ls2080a_common.h
index cc61af8..dd56114 100644
--- a/include/configs/ls2080a_common.h
+++ b/include/configs/ls2080a_common.h
@@ -193,18 +193,18 @@ unsigned long long get_qixis_addr(void);
"ramdisk_size=0x2000000\0" \
"fdt_high=0xa0000000\0" \
"initrd_high=0xffffffffffffffff\0" \
- "kernel_start=0x581200000\0" \
+ "kernel_start=0x581000000\0" \
"kernel_load=0xa0000000\0" \
"kernel_size=0x2800000\0" \
"console=ttyAMA0,38400n8\0" \
- "mcinitcmd=fsl_mc start mc 0x580300000" \
- " 0x580800000 \0"
+ "mcinitcmd=fsl_mc start mc 0x580a00000" \
+ " 0x580e00000 \0"
#define CONFIG_BOOTARGS "console=ttyS0,115200 root=/dev/ram0 " \
"earlycon=uart8250,mmio,0x21c0500 " \
"ramdisk_size=0x2000000 default_hugepagesz=2m" \
" hugepagesz=2m hugepages=256"
-#define CONFIG_BOOTCOMMAND "fsl_mc apply dpl 0x580700000 &&" \
+#define CONFIG_BOOTCOMMAND "fsl_mc apply dpl 0x580d00000 &&" \
" cp.b $kernel_start $kernel_load" \
" $kernel_size && bootm $kernel_load"
diff --git a/include/configs/ls2080aqds.h b/include/configs/ls2080aqds.h
index 16ef350..fc52c26 100644
--- a/include/configs/ls2080aqds.h
+++ b/include/configs/ls2080aqds.h
@@ -274,7 +274,7 @@ unsigned long get_board_ddr_clk(void);
#ifndef CONFIG_QSPI_BOOT
#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x200000)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x300000)
#define CONFIG_ENV_SECT_SIZE 0x20000
#define CONFIG_ENV_SIZE 0x2000
#endif
@@ -386,12 +386,12 @@ unsigned long get_board_ddr_clk(void);
"ramdisk_size=0x2000000\0" \
"fdt_high=0xa0000000\0" \
"initrd_high=0xffffffffffffffff\0" \
- "kernel_start=0x581100000\0" \
+ "kernel_start=0x581000000\0" \
"kernel_load=0xa0000000\0" \
"kernel_size=0x2800000\0" \
"mcmemsize=0x40000000\0" \
- "mcinitcmd=fsl_mc start mc 0x580300000" \
- " 0x580800000 \0"
+ "mcinitcmd=fsl_mc start mc 0x580a00000" \
+ " 0x580e00000 \0"
#endif /* CONFIG_SECURE_BOOT */
diff --git a/include/configs/ls2080ardb.h b/include/configs/ls2080ardb.h
index dd72aa0..f61b82f 100644
--- a/include/configs/ls2080ardb.h
+++ b/include/configs/ls2080ardb.h
@@ -248,7 +248,7 @@ unsigned long get_board_sys_clk(void);
#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3
#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x200000)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x300000)
#define CONFIG_ENV_SECT_SIZE 0x20000
#define CONFIG_ENV_SIZE 0x2000
#endif
@@ -392,13 +392,13 @@ unsigned long get_board_sys_clk(void);
"ramdisk_size=0x2000000\0" \
"fdt_high=0xa0000000\0" \
"initrd_high=0xffffffffffffffff\0" \
- "kernel_start=0x581100000\0" \
+ "kernel_start=0x581000000\0" \
"kernel_load=0xa0000000\0" \
"kernel_size=0x2800000\0" \
"mcmemsize=0x40000000\0" \
"fdtfile=fsl-ls2080a-rdb.dtb\0" \
- "mcinitcmd=fsl_mc start mc 0x580300000" \
- " 0x580800000 \0" \
+ "mcinitcmd=fsl_mc start mc 0x580a00000" \
+ " 0x580e00000 \0" \
BOOTENV
#endif
#endif
@@ -418,7 +418,7 @@ unsigned long get_board_sys_clk(void);
" || run distro_bootcmd"
#else
/* Try to boot an on-NOR kernel first, then do normal distro boot */
-#define CONFIG_BOOTCOMMAND "run mcinitcmd && fsl_mc lazyapply dpl 0x580700000" \
+#define CONFIG_BOOTCOMMAND "run mcinitcmd && fsl_mc lazyapply dpl 0x580d00000" \
" && cp.b $kernel_start $kernel_load $kernel_size" \
" && bootm $kernel_load" \
" || run distro_bootcmd"
@@ -434,7 +434,7 @@ unsigned long get_board_sys_clk(void);
#ifdef CONFIG_QSPI_BOOT
#define CONFIG_CORTINA_FW_ADDR 0x20980000
#else
-#define CONFIG_CORTINA_FW_ADDR 0x581000000
+#define CONFIG_CORTINA_FW_ADDR 0x580980000
#endif
#define CONFIG_CORTINA_FW_LENGTH 0x40000
--
1.9.1
More information about the U-Boot
mailing list