[U-Boot] [PATCH v4 23/66] drivers: spl: consistently use the $(SPL_TPL_) macro

[Philipp Tomsich]

To simplify drivers/Makefile a bit when using TPL/SPL, we consistently
use the $(SPL_TPL_) macro to test for drivers that have separate
configuration symbols for the full U-boot, SPL and TPL stages.
Instead of explicitly repeating them in two separate if-guarded
sections of the Makefile, we can now simply list these options once.

Signed-off-by: Philipp Tomsich <philipp.tomsich at theobroma-systems.com>

Reviewed-by: Simon Glass <sjg at chromium.org>
Reviewed-by: Tom Rini <trini at konsulko.com>
---

Changes in v4: None
Changes in v3: None
Changes in v2: None

 drivers/Makefile | 36 ++++++++++++++++--------------------
 1 file changed, 16 insertions(+), 20 deletions(-)

diff --git a/drivers/Makefile b/drivers/Makefile
index 8624bd8..b98550e 100644
--- a/drivers/Makefile
+++ b/drivers/Makefile
@@ -2,33 +2,34 @@
 # SPDX-License-Identifier:	GPL-2.0+
 #
 
-obj-$(CONFIG_$(SPL_TPL_)DM)	+= core/
-obj-$(CONFIG_$(SPL_)CLK)	+= clk/
-obj-$(CONFIG_$(SPL_)LED)	+= led/
-obj-$(CONFIG_$(SPL_)PHY)	+= phy/
-obj-$(CONFIG_$(SPL_)PINCTRL)	+= pinctrl/
-obj-$(CONFIG_$(SPL_)RAM)	+= ram/
+obj-$(CONFIG_$(SPL_TPL_)CLK) += clk/
+obj-$(CONFIG_$(SPL_TPL_)DM) += core/
+obj-$(CONFIG_$(SPL_TPL_)DRIVERS_MISC_SUPPORT) += misc/ sysreset/ firmware/
+obj-$(CONFIG_$(SPL_TPL_)I2C_SUPPORT) += i2c/
+obj-$(CONFIG_$(SPL_TPL_)LED) += led/
+obj-$(CONFIG_$(SPL_TPL_)MMC_SUPPORT) += mmc/
+obj-$(CONFIG_$(SPL_TPL_)NAND_SUPPORT) += mtd/nand/
+obj-$(CONFIG_$(SPL_TPL_)PHY) += phy/
+obj-$(CONFIG_$(SPL_TPL_)PINCTRL) += pinctrl/
+obj-$(CONFIG_$(SPL_TPL_)RAM) += ram/
+obj-$(CONFIG_$(SPL_TPL_)SERIAL_SUPPORT) += serial/
+obj-$(CONFIG_$(SPL_TPL_)SPI_FLASH_SUPPORT) += mtd/spi/
+obj-$(CONFIG_$(SPL_TPL_)SPI_SUPPORT) += spi/
 
+ifndef CONFIG_TPL_BUILD
 ifdef CONFIG_SPL_BUILD
 
 obj-$(CONFIG_SPL_CPU_SUPPORT) += cpu/
 obj-$(CONFIG_SPL_CRYPTO_SUPPORT) += crypto/
-obj-$(CONFIG_SPL_I2C_SUPPORT) += i2c/
 obj-$(CONFIG_SPL_GPIO_SUPPORT) += gpio/
-obj-$(CONFIG_SPL_MMC_SUPPORT) += mmc/
 obj-$(CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT) += ddr/fsl/
 obj-$(CONFIG_ARMADA_38X) += ddr/marvell/a38x/
 obj-$(CONFIG_ARMADA_XP) += ddr/marvell/axp/
 obj-$(CONFIG_ALTERA_SDRAM) += ddr/altera/
-obj-$(CONFIG_SPL_SERIAL_SUPPORT) += serial/
-obj-$(CONFIG_SPL_SPI_SUPPORT) += spi/
 obj-$(CONFIG_SPL_POWER_SUPPORT) += power/ power/pmic/
 obj-$(CONFIG_SPL_POWER_SUPPORT) += power/regulator/
-obj-$(CONFIG_SPL_DRIVERS_MISC_SUPPORT) += misc/ sysreset/ firmware/
 obj-$(CONFIG_SPL_MTD_SUPPORT) += mtd/
-obj-$(CONFIG_SPL_NAND_SUPPORT) += mtd/nand/
 obj-$(CONFIG_SPL_ONENAND_SUPPORT) += mtd/onenand/
-obj-$(CONFIG_SPL_SPI_FLASH_SUPPORT) += mtd/spi/
 obj-$(CONFIG_SPL_UBI) += mtd/ubispl/
 obj-$(CONFIG_SPL_DMA_SUPPORT) += dma/
 obj-$(CONFIG_SPL_ETH_SUPPORT) += net/
@@ -48,18 +49,13 @@ obj-$(CONFIG_OMAP_USB_PHY) += usb/phy/
 obj-$(CONFIG_SPL_SATA_SUPPORT) += ata/ scsi/
 obj-$(CONFIG_SPL_USB_HOST_SUPPORT) += block/
 obj-$(CONFIG_SPL_MMC_SUPPORT) += block/
+
+endif
 endif
 
 ifdef CONFIG_TPL_BUILD
 
-obj-$(CONFIG_TPL_I2C_SUPPORT) += i2c/
-obj-$(CONFIG_TPL_DRIVERS_MISC_SUPPORT) += misc/ sysreset/ firmware/
-obj-$(CONFIG_TPL_MMC_SUPPORT) += mmc/
 obj-$(CONFIG_TPL_MPC8XXX_INIT_DDR_SUPPORT) += ddr/fsl/
-obj-$(CONFIG_TPL_NAND_SUPPORT) += mtd/nand/
-obj-$(CONFIG_TPL_SERIAL_SUPPORT) += serial/
-obj-$(CONFIG_TPL_SPI_FLASH_SUPPORT) += mtd/spi/
-obj-$(CONFIG_TPL_SPI_SUPPORT) += spi/
 
 endif
 
-- 
2.1.4