[U-Boot] [PATCH v0 13/20] efi_loader: use proper device-paths for partitions
Jonathan Gray
jsg at jsg.id.au
Tue Aug 8 01:36:06 UTC 2017
On Mon, Aug 07, 2017 at 12:16:54PM -0400, Rob Clark wrote:
> On Mon, Aug 7, 2017 at 11:47 AM, Jonathan Gray <jsg at jsg.id.au> wrote:
> > On Sun, Aug 06, 2017 at 11:34:15AM -0400, Rob Clark wrote:
> >> On Sun, Aug 6, 2017 at 10:45 AM, Rob Clark <robdclark at gmail.com> wrote:
> >> >
> >> > I've started trying to hack up test_efi_loader.py to add a test that
> >> > loads OpenBSD's bootloader.. kinda muddling through it at this point,
> >> > since not a py expert or too familiar w/ u-boot's test framework. But
> >> > I'll see if I can get to the point where I can run the same thing on
> >> > various arm7 and aarch64 devices in qemu.
> >> >
> >>
> >> Making a bit of progress on this (running it on a vexpress_ca15_tc2
> >> board in qemu).. any hint where I can find BOOTARM.EFI src code?
> >>
> >> => tftpboot 80400000 obsdboot.efi
> >> smc911x: MAC 52:54:00:12:34:56
> >> smc911x: detected LAN9118 controller
> >> smc911x: phy initialized
> >> smc911x: MAC 52:54:00:12:34:56
> >> Using smc911x-0 device
> >> TFTP from server 10.0.2.2; our IP address is 10.0.2.15
> >> Filename 'obsdboot.efi'.
> >> Load address: 0x80400000
> >> Loading: *%08#####
> >> 12.4 MiB/s
> >> done
> >> Bytes transferred = 64908 (fd8c hex)
> >> smc911x: MAC 52:54:00:12:34:56
> >> => crc32 80400000 $filesize
> >> CRC32 for 80400000 ... 8040fd8b ==> a9ac4fcf
> >> => bootefi 80400000
> >> ## Starting EFI application at 80400000 ...
> >> WARNING: Invalid device tree, expect boot to fail
> >> BS->LocateHandle() returns 0
> >> undefined instruction
> >> pc : [<9eec65c4>] lr : [<9eeca390>]
> >> sp : 9fed7a18 ip : 0000003f fp : 9fed7a2c
> >> r10: 00000000 r9 : 9eed4658 r8 : 00000000
> >> r7 : 9eed1ce4 r6 : 9eed3538 r5 : 9fed7a6c r4 : 9eed4658
> >> r3 : 00000000 r2 : 9eed2f8e r1 : 9eed1ee0 r0 : 00000000
> >> Flags: nZCv IRQs off FIQs off Mode SVC_32
> >> Resetting CPU ...
> >>
> >> resetting ...
> >>
> >>
> >> U-Boot 2017.09-rc1-00025-g534695d189 (Aug 06 2017 - 06:58:16 -0400)
> >>
> >> DRAM: 1 GiB
> >> WARNING: Caches not enabled
> >> Flash: 128 MiB
> >> MMC: MMC: 0
> >> *** Warning - bad CRC, using default environment
> >>
> >> In: serial
> >> Out: serial
> >> Err: serial
> >> Net: smc911x-0
> >> Hit any key to stop autoboot: 2
> >
> > Why does U-Boot not set fdt_addr_r or fdtfile for vexpress? Worse yet
> > trying to load to the default kernel_addr_r fails. So it requires a
> > script or manual commands to boot instead of the usual distro boot
> > arrangement?
>
> I suspect this is specific to the test framework (probably not
> enabling distro-boot-cmd so that the test framework can run the cmds
> it wants??)
I didn't attempt to use the test framework, just loaded the result
of building vexpress_ca15_tc2_defconfig into qemu.
It looks like the load addresses are only good for >= 1G physmem.
U-Boot 2017.09-rc1 (Aug 02 2017 - 10:55:19 +1000)
DRAM: 128 MiB
WARNING: Caches not enabled
Flash: 128 MiB
MMC: MMC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: smc911x-0
Hit any key to stop autoboot: 0
=> printenv
arch=arm
baudrate=38400
board=vexpress
board_name=vexpress
boot_a_script=load ${devtype} ${devnum}:${distro_bootpart} ${scriptaddr} ${prefix}${script}; source ${scriptaddr}
boot_efi_binary=load ${devtype} ${devnum}:${distro_bootpart} ${kernel_addr_r} efi/boot/bootarm.efi; if fdt addr ${fdt_addr_r}; then bootefi ${kernel_addr_r} ${fdt_addr_r};else bootefi ${kernel_addr_r} ${fdtcontroladdr};fi
boot_extlinux=sysboot ${devtype} ${devnum}:${distro_bootpart} any ${scriptaddr} ${prefix}extlinux/extlinux.conf
boot_prefixes=/ /boot/
boot_script_dhcp=boot.scr.uimg
boot_scripts=boot.scr.uimg boot.scr
boot_targets=mmc1 mmc0 pxe dhcp
bootcmd=run distro_bootcmd; run bootflash;
bootcmd_dhcp=if dhcp ${scriptaddr} ${boot_script_dhcp}; then source ${scriptaddr}; fi;setenv efi_fdtfile ${fdtfile}; if test -z "${fdtfile}" -a -n "${soc}"; then setenv efi_fdtfile ${soc}-${board}${boardver}.dtb; fi; setenv efi_old_vci ${bootp_vci};setenv efi_old_arch ${bootp_arch};setenv bootp_vci PXEClient:Arch:00010:UNDI:003000;setenv bootp_arch 0xa;if dhcp ${kernel_addr_r}; then tftpboot ${fdt_addr_r} dtb/${efi_fdtfile};if fdt addr ${fdt_addr_r}; then bootefi ${kernel_addr_r} ${fdt_addr_r}; else bootefi ${kernel_addr_r} ${fdtcontroladdr};fi;fi;setenv bootp_vci ${efi_old_vci};setenv bootp_arch ${efi_old_arch};setenv efi_fdtfile;setenv efi_old_arch;setenv efi_old_vci;
bootcmd_mmc0=setenv devnum 0; run mmc_boot
bootcmd_mmc1=setenv devnum 1; run mmc_boot
bootcmd_pxe=dhcp; if pxe get; then pxe boot; fi
bootdelay=2
bootflash=run flashargs; cp ${ramdisk_addr} ${ramdisk_addr_r} ${maxramdisk}; bootm ${kernel_addr} ${ramdisk_addr_r}
console=ttyAMA0,38400n8
cpu=armv7
distro_bootcmd=for target in ${boot_targets}; do run bootcmd_${target}; done
dram=1024M
efi_dtb_prefixes=/ /dtb/ /dtb/current/
ethact=smc911x-0
ethaddr=52:54:00:12:34:56
flashargs=setenv bootargs root=${root} console=${console} mem=${dram} mtdparts=${mtd} mmci.fmax=190000 devtmpfs.mount=0 vmalloc=256M
kernel_addr=0x0c100000
kernel_addr_r=0xa0008000
load_efi_dtb=load ${devtype} ${devnum}:${distro_bootpart} ${fdt_addr_r} ${prefix}${efi_fdtfile}
loadaddr=0xa0008000
maxramdisk=0x1800000
mmc_boot=if mmc dev ${devnum}; then setenv devtype mmc; run scan_dev_for_boot_part; fi
mtd=armflash:1M at 0x800000(uboot),7M at 0x1000000(kernel),24M at 0x2000000(initrd)
pxefile_addr_r=0xa8000000
ramdisk_addr=0x0c800000
ramdisk_addr_r=0x81000000
root=/dev/sda1 rw
scan_dev_for_boot=echo Scanning ${devtype} ${devnum}:${distro_bootpart}...; for prefix in ${boot_prefixes}; do run scan_dev_for_extlinux; run scan_dev_for_scripts; done;run scan_dev_for_efi;
scan_dev_for_boot_part=part list ${devtype} ${devnum} -bootable devplist; env exists devplist || setenv devplist 1; for distro_bootpart in ${devplist}; do if fstype ${devtype} ${devnum}:${distro_bootpart} bootfstype; then run scan_dev_for_boot; fi; done
scan_dev_for_efi=setenv efi_fdtfile ${fdtfile}; if test -z "${fdtfile}" -a -n "${soc}"; then setenv efi_fdtfile ${soc}-${board}${boardver}.dtb; fi; for prefix in ${efi_dtb_prefixes}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${efi_fdtfile}; then run load_efi_dtb; fi;done;if test -e ${devtype} ${devnum}:${distro_bootpart} efi/boot/bootarm.efi; then echo Found EFI removable media binary efi/boot/bootarm.efi; run boot_efi_binary; echo EFI LOAD FAILED: continuing...; fi; setenv efi_fdtfile
scan_dev_for_extlinux=if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}extlinux/extlinux.conf; then echo Found ${prefix}extlinux/extlinux.conf; run boot_extlinux; echo SCRIPT FAILED: continuing...; fi
scan_dev_for_scripts=for script in ${boot_scripts}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${script}; then echo Found U-Boot script ${prefix}${script}; run boot_a_script; echo SCRIPT FAILED: continuing...; fi; done
scriptaddr=0xa8000000
stderr=serial
stdin=serial
stdout=serial
vendor=armltd
Environment size: 3974/262140 bytes
=> bdinfo
arch_number = 0x000008E0
boot_params = 0x80002000
DRAM bank = 0x00000000
-> start = 0x80000000
-> size = 0x08000000
DRAM bank = 0x00000001
-> start = 0xA0000000
-> size = 0x00000004
eth0name = smc911x-0
ethaddr = 52:54:00:12:34:56
current eth = smc911x-0
ip_addr = <NULL>
baudrate = 38400 bps
TLB addr = 0x87FF0000
relocaddr = 0x87F7B000
reloc off = 0x0777B000
irq_sp = 0x87EDAEF0
sp start = 0x87EDAEE0
With -m 512
U-Boot 2017.09-rc1 (Aug 02 2017 - 10:55:19 +1000)
DRAM: 512 MiB
WARNING: Caches not enabled
Flash: 128 MiB
MMC: MMC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: smc911x-0
Hit any key to stop autoboot: 0
=> bdinfo
arch_number = 0x000008E0
boot_params = 0x80002000
DRAM bank = 0x00000000
-> start = 0x80000000
-> size = 0x20000000
DRAM bank = 0x00000001
-> start = 0xA0000000
-> size = 0x00000004
eth0name = smc911x-0
ethaddr = 52:54:00:12:34:56
current eth = smc911x-0
ip_addr = <NULL>
baudrate = 38400 bps
TLB addr = 0x9FFF0000
relocaddr = 0x9FF7B000
reloc off = 0x1F77B000
irq_sp = 0x9FEDAEF0
sp start = 0x9FEDAEE0
With -m 1024
U-Boot 2017.09-rc1 (Aug 02 2017 - 10:55:19 +1000)
DRAM: 1 GiB
WARNING: Caches not enabled
Flash: 128 MiB
MMC: MMC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: smc911x-0
Hit any key to stop autoboot: 0
=> bdinfo
arch_number = 0x000008E0
boot_params = 0x80002000
DRAM bank = 0x00000000
-> start = 0x80000000
-> size = 0x20000000
DRAM bank = 0x00000001
-> start = 0xA0000000
-> size = 0x20000000
eth0name = smc911x-0
ethaddr = 52:54:00:12:34:56
current eth = smc911x-0
ip_addr = <NULL>
baudrate = 38400 bps
TLB addr = 0x9FFF0000
relocaddr = 0x9FF7B000
reloc off = 0x1F77B000
irq_sp = 0x9FEDAEF0
sp start = 0x9FEDAEE0
-m 1024 works with ${kernel_addr_r} instead of giving
"efi_load_pe: Invalid DOS Signature"
=> setenv fdt_addr_r 0x81000000
=> setenv fdtfile vexpress-v2p-ca15-tc1.dtb
=> load mmc 0:1 ${fdt_addr_r} ${fdtfile}
reading vexpress-v2p-ca15-tc1.dtb
13384 bytes read in 22 ms (593.8 KiB/s)
=> load mmc 0:1 ${kernel_addr_r} efi/boot/bootarm.efi
reading efi/boot/bootarm.efi
64908 bytes read in 49 ms (1.3 MiB/s)
=> bootefi ${kernel_addr_r} ${fdt_addr_r}
## Starting EFI application at a0008000 ...
Scanning disks on mmc...
MMC Device 1 not found
MMC Device 2 not found
MMC Device 3 not found
Found 1 disks
>> OpenBSD/armv7 BOOTARM 0.8
boot>
cannot open sd0a:/etc/random.seed: No such file or directory
booting sd0a:/bsd: 2265112+7989364+447000 [80+314496+149702]=0xaad1c0
OpenBSD/armv7 booting ...
arg0 0xc0dad1c0 arg1 0x8e0 arg2 0x88000000
Allocating page tables
freestart = 0x80dae000, free_pages = 127570 (0x0001f252)
IRQ stack: p0x80ddc000 v0xc0ddc000
ABT stack: p0x80ddd000 v0xc0ddd000
UND stack: p0x80dde000 v0xc0dde000
SVC stack: p0x80ddf000 v0xc0ddf000
Creating L1 page table at 0x80db0000
Mapping kernel
Constructing L2 page tables
undefined page pmap board type: 2272
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2017 OpenBSD. All rights reserved. https://www.OpenBSD.org
OpenBSD 6.1-current (RAMDISK) #30: Sat Aug 5 22:01:16 MDT 2017
deraadt at armv7.openbsd.org:/usr/src/sys/arch/armv7/compile/RAMDISK
real mem = 1073741824 (1024MB)
avail mem = 1038520320 (990MB)
mainbus0 at root: V2P-CA15
cpu0 at mainbus0: ARM Cortex-A15 r2p1 (ARMv7)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(64b/l,2way) I-cache, 32KB(64b/l,2way) wr-back D-cache
cortex0 at mainbus0
ampintc0 at mainbus0 nirq 160, ncpu 1
agtimer0 at mainbus0: tick rate 62500 KHz
simplebus0 at mainbus0: "smb"
simplebus1 at simplebus0: "motherboard"
simplebus2 at simplebus1: "iofpga"
sysreg0 at simplebus2: ID 0x1190f500 PROCID0 0x14000237
pluart0 at simplebus2: console
pluart1 at simplebus2
pluart2 at simplebus2
pluart3 at simplebus2
plrtc0 at simplebus2
simplebus3 at mainbus0: "hsb"
boot device: lookup 'sd0a:/bsd' failed.
root on rd0a swap on rd0b dump on rd0b
e
More information about the U-Boot
mailing list