[U-Boot] [PATCH 11/12] imx: mx6sabresd: enable dm drivers
Peng Fan
peng.fan at nxp.com
Wed Aug 9 09:16:22 UTC 2017
Enable DM MMC/I2C/PMIC/GPIO/REGULATOR.
Signed-off-by: Peng Fan <peng.fan at nxp.com>
Cc: Fabio Estevam <fabio.estevam at nxp.com>
Cc: Stefano Babic <sbabic at denx.de>
---
board/freescale/mx6sabresd/mx6sabresd.c | 326 +++++++++++++-------------------
configs/mx6sabresd_defconfig | 15 ++
include/configs/mx6sabresd.h | 15 +-
3 files changed, 146 insertions(+), 210 deletions(-)
diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c
index ff99a30..845b5b5 100644
--- a/board/freescale/mx6sabresd/mx6sabresd.c
+++ b/board/freescale/mx6sabresd/mx6sabresd.c
@@ -12,7 +12,6 @@
#include <asm/arch/mx6-pins.h>
#include <linux/errno.h>
#include <asm/gpio.h>
-#include <asm/mach-imx/mxc_i2c.h>
#include <asm/mach-imx/iomux-v3.h>
#include <asm/mach-imx/boot_mode.h>
#include <asm/mach-imx/video.h>
@@ -24,7 +23,6 @@
#include <asm/arch/crm_regs.h>
#include <asm/io.h>
#include <asm/arch/sys_proto.h>
-#include <i2c.h>
#include <power/pmic.h>
#include <power/pfuze100_pmic.h>
#include "../common/pfuze.h"
@@ -46,14 +44,6 @@ DECLARE_GLOBAL_DATA_PTR;
#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
-#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
- PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
- PAD_CTL_ODE | PAD_CTL_SRE_FAST)
-
-#define I2C_PMIC 1
-
-#define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL)
-
#define DISP0_PWR_EN IMX_GPIO_NR(1, 21)
#define KEY_VOL_UP IMX_GPIO_NR(1, 4)
@@ -93,6 +83,7 @@ static void setup_iomux_enet(void)
{
SETUP_IOMUX_PADS(enet_pads);
+ gpio_request(IMX_GPIO_NR(1, 25), "phy_rst");
/* Reset AR8031 PHY */
gpio_direction_output(IMX_GPIO_NR(1, 25) , 0);
mdelay(10);
@@ -100,47 +91,6 @@ static void setup_iomux_enet(void)
udelay(100);
}
-static iomux_v3_cfg_t const usdhc2_pads[] = {
- IOMUX_PADS(PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_NANDF_D4__SD2_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_NANDF_D5__SD2_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_NANDF_D6__SD2_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_NANDF_D7__SD2_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_NANDF_D2__GPIO2_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL)), /* CD */
-};
-
-static iomux_v3_cfg_t const usdhc3_pads[] = {
- IOMUX_PADS(PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_NANDF_D0__GPIO2_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL)), /* CD */
-};
-
-static iomux_v3_cfg_t const usdhc4_pads[] = {
- IOMUX_PADS(PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
-};
-
static iomux_v3_cfg_t const ecspi1_pads[] = {
IOMUX_PADS(PAD_KEY_COL0__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL)),
IOMUX_PADS(PAD_KEY_COL1__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL)),
@@ -187,6 +137,7 @@ static iomux_v3_cfg_t const bl_pads[] = {
static void enable_backlight(void)
{
SETUP_IOMUX_PADS(bl_pads);
+ gpio_request(DISP0_PWR_EN, "disp0_pwr_en");
gpio_direction_output(DISP0_PWR_EN, 1);
}
@@ -201,32 +152,6 @@ static void enable_lvds(struct display_info_t const *dev)
enable_backlight();
}
-static struct i2c_pads_info mx6q_i2c_pad_info1 = {
- .scl = {
- .i2c_mode = MX6Q_PAD_KEY_COL3__I2C2_SCL | I2C_PAD,
- .gpio_mode = MX6Q_PAD_KEY_COL3__GPIO4_IO12 | I2C_PAD,
- .gp = IMX_GPIO_NR(4, 12)
- },
- .sda = {
- .i2c_mode = MX6Q_PAD_KEY_ROW3__I2C2_SDA | I2C_PAD,
- .gpio_mode = MX6Q_PAD_KEY_ROW3__GPIO4_IO13 | I2C_PAD,
- .gp = IMX_GPIO_NR(4, 13)
- }
-};
-
-static struct i2c_pads_info mx6dl_i2c_pad_info1 = {
- .scl = {
- .i2c_mode = MX6DL_PAD_KEY_COL3__I2C2_SCL | I2C_PAD,
- .gpio_mode = MX6DL_PAD_KEY_COL3__GPIO4_IO12 | I2C_PAD,
- .gp = IMX_GPIO_NR(4, 12)
- },
- .sda = {
- .i2c_mode = MX6DL_PAD_KEY_ROW3__I2C2_SDA | I2C_PAD,
- .gpio_mode = MX6DL_PAD_KEY_ROW3__GPIO4_IO13 | I2C_PAD,
- .gp = IMX_GPIO_NR(4, 13)
- }
-};
-
static void setup_spi(void)
{
SETUP_IOMUX_PADS(ecspi1_pads);
@@ -253,121 +178,11 @@ static void setup_iomux_uart(void)
SETUP_IOMUX_PADS(uart1_pads);
}
-#ifdef CONFIG_FSL_ESDHC
-struct fsl_esdhc_cfg usdhc_cfg[3] = {
- {USDHC2_BASE_ADDR},
- {USDHC3_BASE_ADDR},
- {USDHC4_BASE_ADDR},
-};
-
-#define USDHC2_CD_GPIO IMX_GPIO_NR(2, 2)
-#define USDHC3_CD_GPIO IMX_GPIO_NR(2, 0)
-
int board_mmc_get_env_dev(int devno)
{
return devno - 1;
}
-int board_mmc_getcd(struct mmc *mmc)
-{
- struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
- int ret = 0;
-
- switch (cfg->esdhc_base) {
- case USDHC2_BASE_ADDR:
- ret = !gpio_get_value(USDHC2_CD_GPIO);
- break;
- case USDHC3_BASE_ADDR:
- ret = !gpio_get_value(USDHC3_CD_GPIO);
- break;
- case USDHC4_BASE_ADDR:
- ret = 1; /* eMMC/uSDHC4 is always present */
- break;
- }
-
- return ret;
-}
-
-int board_mmc_init(bd_t *bis)
-{
-#ifndef CONFIG_SPL_BUILD
- int ret;
- int i;
-
- /*
- * According to the board_mmc_init() the following map is done:
- * (U-Boot device node) (Physical Port)
- * mmc0 SD2
- * mmc1 SD3
- * mmc2 eMMC
- */
- for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
- switch (i) {
- case 0:
- SETUP_IOMUX_PADS(usdhc2_pads);
- gpio_direction_input(USDHC2_CD_GPIO);
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
- break;
- case 1:
- SETUP_IOMUX_PADS(usdhc3_pads);
- gpio_direction_input(USDHC3_CD_GPIO);
- usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
- break;
- case 2:
- SETUP_IOMUX_PADS(usdhc4_pads);
- usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
- break;
- default:
- printf("Warning: you configured more USDHC controllers"
- "(%d) then supported by the board (%d)\n",
- i + 1, CONFIG_SYS_FSL_USDHC_NUM);
- return -EINVAL;
- }
-
- ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
- if (ret)
- return ret;
- }
-
- return 0;
-#else
- struct src *psrc = (struct src *)SRC_BASE_ADDR;
- unsigned reg = readl(&psrc->sbmr1) >> 11;
- /*
- * Upon reading BOOT_CFG register the following map is done:
- * Bit 11 and 12 of BOOT_CFG register can determine the current
- * mmc port
- * 0x1 SD1
- * 0x2 SD2
- * 0x3 SD4
- */
-
- switch (reg & 0x3) {
- case 0x1:
- SETUP_IOMUX_PADS(usdhc2_pads);
- usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR;
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
- gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
- break;
- case 0x2:
- SETUP_IOMUX_PADS(usdhc3_pads);
- usdhc_cfg[0].esdhc_base = USDHC3_BASE_ADDR;
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
- gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
- break;
- case 0x3:
- SETUP_IOMUX_PADS(usdhc4_pads);
- usdhc_cfg[0].esdhc_base = USDHC4_BASE_ADDR;
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
- gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
- break;
- }
-
- return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
-#endif
-}
-#endif
-
static int ar8031_phy_fixup(struct phy_device *phydev)
{
unsigned short val;
@@ -580,6 +395,8 @@ static void setup_usb(void)
imx_iomux_set_gpr_register(1, 13, 1, 0);
SETUP_IOMUX_PADS(usb_hc1_pads);
+
+ gpio_request(IMX_GPIO_NR(1, 29), "usb1");
}
int board_ehci_hcd_init(int port)
@@ -632,13 +449,13 @@ int board_init(void)
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+ gpio_request(IMX_GPIO_NR(3, 19), "pcie_power");
+ gpio_request(IMX_GPIO_NR(7, 12), "pcie_reset");
+
#ifdef CONFIG_MXC_SPI
setup_spi();
#endif
- if (is_mx6dq() || is_mx6dqp())
- setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6q_i2c_pad_info1);
- else
- setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c_pad_info1);
+
#ifdef CONFIG_USB_EHCI_MX6
setup_usb();
#endif
@@ -646,34 +463,36 @@ int board_init(void)
return 0;
}
+#ifndef CONFIG_SPL_BUILD
int power_init_board(void)
{
- struct pmic *p;
+ struct udevice *dev;
unsigned int reg;
int ret;
- p = pfuze_common_init(I2C_PMIC);
- if (!p)
+ dev = pfuze_common_init();
+ if (!dev)
return -ENODEV;
- ret = pfuze_mode_init(p, APS_PFM);
+ ret = pfuze_mode_init(dev, APS_PFM);
if (ret < 0)
return ret;
/* Increase VGEN3 from 2.5 to 2.8V */
- pmic_reg_read(p, PFUZE100_VGEN3VOL, ®);
+ reg = pmic_reg_read(dev, PFUZE100_VGEN3VOL);
reg &= ~LDO_VOL_MASK;
reg |= LDOB_2_80V;
- pmic_reg_write(p, PFUZE100_VGEN3VOL, reg);
+ pmic_reg_write(dev, PFUZE100_VGEN3VOL, reg);
/* Increase VGEN5 from 2.8 to 3V */
- pmic_reg_read(p, PFUZE100_VGEN5VOL, ®);
+ reg = pmic_reg_read(dev, PFUZE100_VGEN5VOL);
reg &= ~LDO_VOL_MASK;
reg |= LDOB_3_00V;
- pmic_reg_write(p, PFUZE100_VGEN5VOL, reg);
+ pmic_reg_write(dev, PFUZE100_VGEN5VOL, reg);
return 0;
}
+#endif
#ifdef CONFIG_MXC_SPI
int board_spi_cs_gpio(unsigned bus, unsigned cs)
@@ -747,6 +566,115 @@ int board_fit_config_name_match(const char *name)
}
#endif
+#ifdef CONFIG_FSL_ESDHC
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+ IOMUX_PADS(PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_D4__SD2_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_D5__SD2_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_D6__SD2_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_D7__SD2_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_D2__GPIO2_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL)), /* CD */
+};
+
+static iomux_v3_cfg_t const usdhc3_pads[] = {
+ IOMUX_PADS(PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_NANDF_D0__GPIO2_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL)), /* CD */
+};
+
+static iomux_v3_cfg_t const usdhc4_pads[] = {
+ IOMUX_PADS(PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+};
+
+struct fsl_esdhc_cfg usdhc_cfg[3] = {
+ {USDHC2_BASE_ADDR},
+ {USDHC3_BASE_ADDR},
+ {USDHC4_BASE_ADDR},
+};
+
+#define USDHC2_CD_GPIO IMX_GPIO_NR(2, 2)
+#define USDHC3_CD_GPIO IMX_GPIO_NR(2, 0)
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+ struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+ int ret = 0;
+
+ switch (cfg->esdhc_base) {
+ case USDHC2_BASE_ADDR:
+ ret = !gpio_get_value(USDHC2_CD_GPIO);
+ break;
+ case USDHC3_BASE_ADDR:
+ ret = !gpio_get_value(USDHC3_CD_GPIO);
+ break;
+ case USDHC4_BASE_ADDR:
+ ret = 1; /* eMMC/uSDHC4 is always present */
+ break;
+ }
+
+ return ret;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+ struct src *psrc = (struct src *)SRC_BASE_ADDR;
+ unsigned reg = readl(&psrc->sbmr1) >> 11;
+ /*
+ * Upon reading BOOT_CFG register the following map is done:
+ * Bit 11 and 12 of BOOT_CFG register can determine the current
+ * mmc port
+ * 0x1 SD1
+ * 0x2 SD2
+ * 0x3 SD4
+ */
+
+ switch (reg & 0x3) {
+ case 0x1:
+ SETUP_IOMUX_PADS(usdhc2_pads);
+ usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR;
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+ gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
+ break;
+ case 0x2:
+ SETUP_IOMUX_PADS(usdhc3_pads);
+ usdhc_cfg[0].esdhc_base = USDHC3_BASE_ADDR;
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+ gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
+ break;
+ case 0x3:
+ SETUP_IOMUX_PADS(usdhc4_pads);
+ usdhc_cfg[0].esdhc_base = USDHC4_BASE_ADDR;
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
+ gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
+ break;
+ }
+
+ return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+}
+#endif
+
static void ccgr_init(void)
{
struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
diff --git a/configs/mx6sabresd_defconfig b/configs/mx6sabresd_defconfig
index a9447e5..9f550ff 100644
--- a/configs/mx6sabresd_defconfig
+++ b/configs/mx6sabresd_defconfig
@@ -37,6 +37,8 @@ CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_CACHE=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_EXT4_WRITE=y
@@ -44,9 +46,22 @@ CONFIG_CMD_FAT=y
CONFIG_CMD_FS_GENERIC=y
CONFIG_OF_CONTROL=y
CONFIG_OF_LIST="imx6q-sabresd imx6dl-sabresd imx6qp-sabresd"
+# CONFIG_BLK is not set
+CONFIG_DM_GPIO=y
+CONFIG_DM_I2C=y
+CONFIG_DM_MMC=y
+# CONFIG_DM_MMC_OPS is not set
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_PCI=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_PMIC_PFUZE100=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_PFUZE100=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
CONFIG_USB=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
diff --git a/include/configs/mx6sabresd.h b/include/configs/mx6sabresd.h
index 27e7672..95e1666 100644
--- a/include/configs/mx6sabresd.h
+++ b/include/configs/mx6sabresd.h
@@ -46,20 +46,9 @@
#define CONFIG_PCIE_IMX_POWER_GPIO IMX_GPIO_NR(3, 19)
#endif
-/* I2C Configs */
-#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
-#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
-#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
-#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
#define CONFIG_SYS_I2C_SPEED 100000
-/* PMIC */
-#define CONFIG_POWER
-#define CONFIG_POWER_I2C
-#define CONFIG_POWER_PFUZE100
-#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
-
/* USB Configs */
#ifdef CONFIG_CMD_USB
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
@@ -70,4 +59,8 @@
#define CONFIG_USB_MAX_CONTROLLER_COUNT 1 /* Enabled USB controller number */
#endif
+#ifdef CONFIG_SPL_BUILD
+#undef CONFIG_SYS_I2C_MXC
+#endif
+
#endif /* __MX6SABRESD_CONFIG_H */
--
2.6.2
More information about the U-Boot
mailing list