[U-Boot] [PATCH V2 22/23] imx: add i.MX8MQ EVK support
Peng Fan
peng.fan at nxp.com
Mon Dec 4 04:31:35 UTC 2017
Add i.MX8MQ EVK support. SPL will initialize ddr and load ddr phy
firmware. Then loading FIT image, ATF to OCRAM, U-Boot and DTB to
DRAM.
The boot log:
"
U-Boot SPL 2017.11-00062-gd4c7c3ebb3-dirty (Dec 01 2017 - 14:49:31)
PMIC: PFUZE100 ID=0x10
check ddr4_pmu_train_imem code
check ddr4_pmu_train_imem code pass
check ddr4_pmu_train_dmem code
check ddr4_pmu_train_dmem code pass
PLL bypass to 100MTS setting done
Training PASS
PLL bypass to 400MTS setting done
Training PASS
Training PASS
check ddr4_pmu_train_imem code
check ddr4_pmu_train_imem code pass
check ddr4_pmu_train_dmem code
check ddr4_pmu_train_dmem code pass
Training PASS
Normal Boot
Trying to boot from MMC2
U-Boot 2017.11-00062-gd4c7c3ebb3-dirty (Dec 01 2017 - 14:49:31 +0800)
CPU: Freescale i.MX8MQ rev2.0 at 1000 MHz
Reset cause: POR
Model: Freescale i.MX8MQ EVK
DRAM: 3 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Using default environment
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Hit any key to stop autoboot: 0
"
Signed-off-by: Peng Fan <peng.fan at nxp.com>
---
arch/arm/dts/Makefile | 2 +
arch/arm/dts/fsl-imx8mq-evk.dts | 424 ++++++++++++++++++++++++++++++++++
arch/arm/mach-imx/mx8m/Kconfig | 12 +
board/freescale/mx8mq_evk/Kconfig | 12 +
board/freescale/mx8mq_evk/Makefile | 11 +
board/freescale/mx8mq_evk/README | 38 +++
board/freescale/mx8mq_evk/mx8mq_evk.c | 156 +++++++++++++
board/freescale/mx8mq_evk/spl.c | 233 +++++++++++++++++++
configs/mx8mq_evk_defconfig | 28 +++
include/configs/mx8mq_evk.h | 265 +++++++++++++++++++++
10 files changed, 1181 insertions(+)
create mode 100644 arch/arm/dts/fsl-imx8mq-evk.dts
create mode 100644 board/freescale/mx8mq_evk/Kconfig
create mode 100644 board/freescale/mx8mq_evk/Makefile
create mode 100644 board/freescale/mx8mq_evk/README
create mode 100644 board/freescale/mx8mq_evk/mx8mq_evk.c
create mode 100644 board/freescale/mx8mq_evk/spl.c
create mode 100644 configs/mx8mq_evk_defconfig
create mode 100644 include/configs/mx8mq_evk.h
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index cd540e99ea..d459755904 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -381,6 +381,8 @@ dtb-$(CONFIG_MX7) += imx7-colibri.dtb \
dtb-$(CONFIG_ARCH_MX7ULP) += imx7ulp-evk.dtb
+dtb-$(CONFIG_ARCH_MX8M) += fsl-imx8mq-evk.dtb
+
dtb-$(CONFIG_RCAR_GEN3) += \
r8a7795-h3ulcb.dtb \
r8a7795-salvator-x.dtb \
diff --git a/arch/arm/dts/fsl-imx8mq-evk.dts b/arch/arm/dts/fsl-imx8mq-evk.dts
new file mode 100644
index 0000000000..f0aa3485e6
--- /dev/null
+++ b/arch/arm/dts/fsl-imx8mq-evk.dts
@@ -0,0 +1,424 @@
+/*
+ * Copyright (C) 2016 Freescale Semiconductor, Inc.
+ * Copyright 2017 NXP
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+/dts-v1/;
+
+/* First 128KB is for PSCI ATF. */
+/memreserve/ 0x40000000 0x00020000;
+
+#include "fsl-imx8mq.dtsi"
+
+/ {
+ model = "Freescale i.MX8MQ EVK";
+ compatible = "fsl,imx8mq-evk", "fsl,imx8mq";
+
+ chosen {
+ bootargs = "console=ttymxc0,115200 earlycon=ec_imx6q,0x30860000,115200";
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg_usdhc2_vmmc: usdhc2_vmmc {
+ compatible = "regulator-fixed";
+ regulator-name = "VSD_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+ };
+
+ pwmleds {
+ compatible = "pwm-leds";
+
+ ledpwm2 {
+ label = "PWM2";
+ pwms = <&pwm2 0 50000>;
+ max-brightness = <255>;
+ };
+ };
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+
+ imx8mq-evk {
+ pinctrl_fec1: fec1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC 0x3
+ MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO 0x23
+ MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
+ MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
+ MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
+ MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
+ MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
+ MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
+ MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
+ MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
+ MX8MQ_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
+ MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
+ MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
+ MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
+ MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL 0x4000007f
+ MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA 0x4000007f
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C2_SCL_I2C2_SCL 0x4000007f
+ MX8MQ_IOMUXC_I2C2_SDA_I2C2_SDA 0x4000007f
+ >;
+ };
+
+ pinctrl_pwm2: pwm2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO13_PWM2_OUT 0x16
+ >;
+ };
+
+ pinctrl_qspi: qspigrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x82
+ MX8MQ_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x82
+ MX8MQ_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x82
+ MX8MQ_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x82
+ MX8MQ_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x82
+ MX8MQ_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x82
+
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x83
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc3
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc3
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc3
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc3
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc3
+ MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc3
+ MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc3
+ MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc3
+ MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc3
+ MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x83
+ MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x85
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc5
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc5
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc5
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc5
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc5
+ MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc5
+ MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc5
+ MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc5
+ MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc5
+ MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x85
+ MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x87
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc7
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc7
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc7
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc7
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc7
+ MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc7
+ MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc7
+ MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc7
+ MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc7
+ MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x87
+ MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1
+ >;
+ };
+
+ pinctrl_usdhc2_gpio: usdhc2grpgpio {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CD_B_GPIO2_IO12 0x41
+ MX8MQ_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x83
+ MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc3
+ MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc3
+ MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc3
+ MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc3
+ MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc3
+ MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x85
+ MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc5
+ MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc5
+ MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc5
+ MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc5
+ MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc5
+ MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x87
+ MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc7
+ MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc7
+ MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc7
+ MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc7
+ MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc7
+ MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1
+ >;
+ };
+
+ pinctrl_sai2: sai2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SAI2_TXFS_SAI2_TX_SYNC 0xd6
+ MX8MQ_IOMUXC_SAI2_TXC_SAI2_TX_BCLK 0xd6
+ MX8MQ_IOMUXC_SAI2_MCLK_SAI2_MCLK 0xd6
+ MX8MQ_IOMUXC_SAI2_TXD0_SAI2_TX_DATA0 0xd6
+ MX8MQ_IOMUXC_GPIO1_IO08_GPIO1_IO8 0xd6
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6
+ >;
+ };
+ };
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec1>;
+ phy-mode = "rgmii-id";
+ phy-handle = <ðphy0>;
+ fsl,magic-packet;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy at 0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ at803x,led-act-blind-workaround;
+ at803x,eee-disabled;
+ };
+ };
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ pmic: pfuze100 at 08 {
+ compatible = "fsl,pfuze100";
+ reg = <0x08>;
+
+ regulators {
+ sw1a_reg: sw1ab {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-always-on;
+ };
+
+ sw1c_reg: sw1c {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-always-on;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ sw3a_reg: sw3ab {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-always-on;
+ };
+
+ sw4_reg: sw4 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ swbst_reg: swbst {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5150000>;
+ };
+
+ snvs_reg: vsnvs {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ };
+
+ vref_reg: vrefddr {
+ regulator-always-on;
+ };
+
+ vgen1_reg: vgen1 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ vgen2_reg: vgen2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ regulator-always-on;
+ };
+
+ vgen3_reg: vgen3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen4_reg: vgen4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen5_reg: vgen5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen6_reg: vgen6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ };
+ };
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "disabled";
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>;
+ status = "okay";
+};
+
+&lcdif {
+ status = "okay";
+ disp-dev = "mipi_dsi_northwest";
+ display = <&display0>;
+
+ display0: display at 0 {
+ bits-per-pixel = <24>;
+ bus-width = <24>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <9200000>;
+ hactive = <480>;
+ vactive = <272>;
+ hfront-porch = <8>;
+ hback-porch = <4>;
+ hsync-len = <41>;
+ vback-porch = <2>;
+ vfront-porch = <4>;
+ vsync-len = <10>;
+
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+};
+
+&qspi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_qspi>;
+ status = "okay";
+
+ flash0: n25q256a at 0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "micron,n25q256a";
+ spi-max-frequency = <29000000>;
+ spi-nor,ddr-quad-read-dummy = <6>;
+ };
+};
+
+&usdhc1 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+ bus-width = <4>;
+ cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <®_usdhc2_vmmc>;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
diff --git a/arch/arm/mach-imx/mx8m/Kconfig b/arch/arm/mach-imx/mx8m/Kconfig
index 3a84c2f2b0..e3b57b7915 100644
--- a/arch/arm/mach-imx/mx8m/Kconfig
+++ b/arch/arm/mach-imx/mx8m/Kconfig
@@ -7,4 +7,16 @@ config MX8M
config SYS_SOC
default "mx8m"
+choice
+ prompt "NXP i.MX8M board select"
+ optional
+
+config TARGET_MX8MQ_EVK
+ bool "mx8mq_evk"
+ select MX8M
+
+endchoice
+
+source "board/freescale/mx8mq_evk/Kconfig"
+
endif
diff --git a/board/freescale/mx8mq_evk/Kconfig b/board/freescale/mx8mq_evk/Kconfig
new file mode 100644
index 0000000000..4e23002803
--- /dev/null
+++ b/board/freescale/mx8mq_evk/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_MX8MQ_EVK
+
+config SYS_BOARD
+ default "mx8mq_evk"
+
+config SYS_VENDOR
+ default "freescale"
+
+config SYS_CONFIG_NAME
+ default "mx8mq_evk"
+
+endif
diff --git a/board/freescale/mx8mq_evk/Makefile b/board/freescale/mx8mq_evk/Makefile
new file mode 100644
index 0000000000..60c99d4194
--- /dev/null
+++ b/board/freescale/mx8mq_evk/Makefile
@@ -0,0 +1,11 @@
+#
+# Copyright 2017 NXP
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y += mx8mq_evk.o
+
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o
+endif
diff --git a/board/freescale/mx8mq_evk/README b/board/freescale/mx8mq_evk/README
new file mode 100644
index 0000000000..6be5f51a22
--- /dev/null
+++ b/board/freescale/mx8mq_evk/README
@@ -0,0 +1,38 @@
+U-Boot for the NXP i.MX8MQ EVK board
+
+Quick Start
+====================
+- Build the ARM Trusted firmware binary
+- Build U-Boot
+- Generate flash.bin using imx-mkimage
+- Boot
+
+Build the ARM Trusted firmware
+====================
+$ make PLAT=imx8mq bl31
+
+Build U-Boot
+====================
+$ export ARCH=arm64
+$ export CROSS_COMPILE=aarch64-poky-linux-
+$ make mx8mq_evk_defconfig
+$ make
+
+Generate flash.bin using imx-mkimage
+====================
+Copy bl31.bin u-boot-nodtb.bin u-boot-spl.bin fsl-imx8mq-evk.dtb to
+ imx-mkimage/iMX8M
+Copy lpddr4_pmu_train_1d_dmem.bin lpddr4_pmu_train_1d_imem.bin
+ lpddr4_pmu_train_2d_dmem.bin lpddr4_pmu_train_2d_imem.bin to
+ imx-mkimage/iMX8M
+If you want to run with HDMI, copy signed_hdmi_imx8m.bin to imx-mkimage/iMX8M
+
+make SOC=iMX8M flash_spl_uboot or make SOC=iMX8M flash_hdmi_spl_uboot to
+generate flash.bin.
+
+Burn the flash.bin to MicroSD card offset 33KB
+$sudo dd if=iMX8M/flash.bin of=/dev/sd[x] bs=1024 seek=33
+
+Boot
+====================
+Set Boot switch SW801: 1100 and Bmode: 10 to boot from Micro SD.
diff --git a/board/freescale/mx8mq_evk/mx8mq_evk.c b/board/freescale/mx8mq_evk/mx8mq_evk.c
new file mode 100644
index 0000000000..e31678efb7
--- /dev/null
+++ b/board/freescale/mx8mq_evk/mx8mq_evk.c
@@ -0,0 +1,156 @@
+/*
+ * Copyright 2017 NXP
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <errno.h>
+#include <asm/io.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <asm-generic/gpio.h>
+#include <fsl_esdhc.h>
+#include <mmc.h>
+#include <asm/arch/mx8mq_pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/mach-imx/gpio.h>
+#include <asm/mach-imx/mxc_i2c.h>
+#include <asm/arch/clock.h>
+#include <spl.h>
+#include <power/pmic.h>
+#include <power/pfuze100_pmic.h>
+#include "../common/pfuze.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define QSPI_PAD_CTRL (PAD_CTL_DSE2 | PAD_CTL_HYS)
+
+#define UART_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_FSEL1)
+
+#define WDOG_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_HYS | PAD_CTL_PUE)
+
+static iomux_v3_cfg_t const wdog_pads[] = {
+ IMX8MQ_PAD_GPIO1_IO02__WDOG1_WDOG_B | MUX_PAD_CTRL(WDOG_PAD_CTRL),
+};
+
+#ifdef CONFIG_FSL_QSPI
+static iomux_v3_cfg_t const qspi_pads[] = {
+ IMX8MQ_PAD_NAND_ALE__QSPI_A_SCLK | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+ IMX8MQ_PAD_NAND_CE0_B__QSPI_A_SS0_B | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+
+ IMX8MQ_PAD_NAND_DATA00__QSPI_A_DATA0 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+ IMX8MQ_PAD_NAND_DATA01__QSPI_A_DATA1 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+ IMX8MQ_PAD_NAND_DATA02__QSPI_A_DATA2 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+ IMX8MQ_PAD_NAND_DATA03__QSPI_A_DATA3 | MUX_PAD_CTRL(QSPI_PAD_CTRL),
+};
+
+int board_qspi_init(void)
+{
+ imx_iomux_v3_setup_multiple_pads(qspi_pads, ARRAY_SIZE(qspi_pads));
+
+ set_clk_qspi();
+
+ return 0;
+}
+#endif
+
+static iomux_v3_cfg_t const uart_pads[] = {
+ IMX8MQ_PAD_UART1_RXD__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+ IMX8MQ_PAD_UART1_TXD__UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+int board_early_init_f(void)
+{
+ struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR;
+
+ imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
+ set_wdog_reset(wdog);
+
+ imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
+
+ return 0;
+}
+
+int dram_init(void)
+{
+ /* rom_pointer[1] contains the size of TEE occupies */
+ if (rom_pointer[1])
+ gd->ram_size = PHYS_SDRAM_SIZE - rom_pointer[1];
+ else
+ gd->ram_size = PHYS_SDRAM_SIZE;
+
+ return 0;
+}
+
+#ifdef CONFIG_FEC_MXC
+#define FEC_RST_PAD IMX_GPIO_NR(1, 9)
+static iomux_v3_cfg_t const fec1_rst_pads[] = {
+ IMX8MQ_PAD_GPIO1_IO09__GPIO1_IO9 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static void setup_iomux_fec(void)
+{
+ imx_iomux_v3_setup_multiple_pads(fec1_rst_pads,
+ ARRAY_SIZE(fec1_rst_pads));
+
+ gpio_request(IMX_GPIO_NR(1, 9), "fec1_rst");
+ gpio_direction_output(IMX_GPIO_NR(1, 9), 0);
+ udelay(500);
+ gpio_direction_output(IMX_GPIO_NR(1, 9), 1);
+}
+
+static int setup_fec(void)
+{
+ struct iomuxc_gpr_base_regs *gpr =
+ (struct iomuxc_gpr_base_regs *)IOMUXC_GPR_BASE_ADDR;
+
+ setup_iomux_fec();
+
+ /* Use 125M anatop REF_CLK1 for ENET1, not from external */
+ clrsetbits_le32(&gpr->gpr[1], BIT(13) | BIT(17), 0);
+ return set_clk_enet(ENET_125MHZ);
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+ /* enable rgmii rxc skew and phy mode select to RGMII copper */
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8);
+
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
+
+ if (phydev->drv->config)
+ phydev->drv->config(phydev);
+ return 0;
+}
+#endif
+
+int board_init(void)
+{
+ board_qspi_init();
+
+#ifdef CONFIG_FEC_MXC
+ setup_fec();
+#endif
+
+ return 0;
+}
+
+int board_mmc_get_env_dev(int devno)
+{
+ return devno;
+}
+
+int board_late_init(void)
+{
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+ env_set("board_name", "EVK");
+ env_set("board_rev", "iMX8MQ");
+#endif
+
+ return 0;
+}
diff --git a/board/freescale/mx8mq_evk/spl.c b/board/freescale/mx8mq_evk/spl.c
new file mode 100644
index 0000000000..522d076124
--- /dev/null
+++ b/board/freescale/mx8mq_evk/spl.c
@@ -0,0 +1,233 @@
+/*
+ * Copyright 2017 NXP
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <spl.h>
+#include <asm/io.h>
+#include <errno.h>
+#include <asm/io.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <asm/arch/mx8mq_pins.h>
+#include <asm/arch/sys_proto.h>
+#include <power/pmic.h>
+#include <power/pfuze100_pmic.h>
+#include "../common/pfuze.h"
+#include <asm/arch/clock.h>
+#include <asm/mach-imx/gpio.h>
+#include <asm/mach-imx/mxc_i2c.h>
+#include <fsl_esdhc.h>
+#include <mmc.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+__weak void ddr_init(void)
+{
+};
+
+void spl_dram_init(void)
+{
+ /* ddr init */
+ ddr_init();
+}
+
+#define I2C_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_HYS | PAD_CTL_PUE)
+#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+struct i2c_pads_info i2c_pad_info1 = {
+ .scl = {
+ .i2c_mode = IMX8MQ_PAD_I2C1_SCL__I2C1_SCL | PC,
+ .gpio_mode = IMX8MQ_PAD_I2C1_SCL__GPIO5_IO14 | PC,
+ .gp = IMX_GPIO_NR(5, 14),
+ },
+ .sda = {
+ .i2c_mode = IMX8MQ_PAD_I2C1_SDA__I2C1_SDA | PC,
+ .gpio_mode = IMX8MQ_PAD_I2C1_SDA__GPIO5_IO15 | PC,
+ .gp = IMX_GPIO_NR(5, 15),
+ },
+};
+
+#define USDHC2_CD_GPIO IMX_GPIO_NR(2, 12)
+#define USDHC1_PWR_GPIO IMX_GPIO_NR(2, 10)
+#define USDHC2_PWR_GPIO IMX_GPIO_NR(2, 19)
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+ struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+ int ret = 0;
+
+ switch (cfg->esdhc_base) {
+ case USDHC1_BASE_ADDR:
+ ret = 1;
+ break;
+ case USDHC2_BASE_ADDR:
+ ret = !gpio_get_value(USDHC2_CD_GPIO);
+ return ret;
+ }
+
+ return 1;
+}
+
+#define USDHC_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_HYS | PAD_CTL_PUE | \
+ PAD_CTL_FSEL2)
+
+static iomux_v3_cfg_t const usdhc1_pads[] = {
+ IMX8MQ_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ IMX8MQ_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ IMX8MQ_PAD_SD1_DATA0__USDHC1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ IMX8MQ_PAD_SD1_DATA1__USDHC1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ IMX8MQ_PAD_SD1_DATA2__USDHC1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ IMX8MQ_PAD_SD1_DATA3__USDHC1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ IMX8MQ_PAD_SD1_DATA4__USDHC1_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ IMX8MQ_PAD_SD1_DATA5__USDHC1_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ IMX8MQ_PAD_SD1_DATA6__USDHC1_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ IMX8MQ_PAD_SD1_DATA7__USDHC1_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ IMX8MQ_PAD_SD1_RESET_B__GPIO2_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+ IMX8MQ_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ IMX8MQ_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ IMX8MQ_PAD_SD2_DATA0__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ IMX8MQ_PAD_SD2_DATA1__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ IMX8MQ_PAD_SD2_DATA2__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ IMX8MQ_PAD_SD2_DATA3__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ IMX8MQ_PAD_SD2_CD_B__GPIO2_IO12 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ IMX8MQ_PAD_SD2_RESET_B__GPIO2_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static struct fsl_esdhc_cfg usdhc_cfg[2] = {
+ {USDHC1_BASE_ADDR, 0, 8},
+ {USDHC2_BASE_ADDR, 0, 4},
+};
+
+int board_mmc_init(bd_t *bis)
+{
+ int i, ret;
+ /*
+ * According to the board_mmc_init() the following map is done:
+ * (U-Boot device node) (Physical Port)
+ * mmc0 USDHC1
+ * mmc1 USDHC2
+ */
+ for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+ switch (i) {
+ case 0:
+ init_clk_usdhc(0);
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(USDHC1_CLK_ROOT);
+ imx_iomux_v3_setup_multiple_pads(
+ usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
+ gpio_request(USDHC1_PWR_GPIO, "usdhc1_reset");
+ gpio_direction_output(USDHC1_PWR_GPIO, 0);
+ udelay(500);
+ gpio_direction_output(USDHC1_PWR_GPIO, 1);
+ break;
+ case 1:
+ init_clk_usdhc(1);
+ usdhc_cfg[1].sdhc_clk = mxc_get_clock(USDHC2_CLK_ROOT);
+ imx_iomux_v3_setup_multiple_pads(
+ usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+ gpio_request(USDHC2_PWR_GPIO, "usdhc2_reset");
+ gpio_direction_output(USDHC2_PWR_GPIO, 0);
+ udelay(500);
+ gpio_direction_output(USDHC2_PWR_GPIO, 1);
+ break;
+ default:
+ printf("Warning: you configured more USDHC controllers(%d) than supported by the board\n", i + 1);
+ return -EINVAL;
+ }
+
+ ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+#ifdef CONFIG_POWER
+#define I2C_PMIC 0
+int power_init_board(void)
+{
+ struct pmic *p;
+ int ret;
+ unsigned int reg;
+
+ ret = power_pfuze100_init(I2C_PMIC);
+ if (ret)
+ return -ENODEV;
+
+ p = pmic_get("PFUZE100");
+ ret = pmic_probe(p);
+ if (ret)
+ return -ENODEV;
+
+ pmic_reg_read(p, PFUZE100_DEVICEID, ®);
+ printf("PMIC: PFUZE100 ID=0x%02x\n", reg);
+
+ pmic_reg_read(p, PFUZE100_SW3AVOL, ®);
+ if ((reg & 0x3f) != 0x18) {
+ reg &= ~0x3f;
+ reg |= 0x18;
+ pmic_reg_write(p, PFUZE100_SW3AVOL, reg);
+ }
+
+ ret = pfuze_mode_init(p, APS_PFM);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+#endif
+
+void spl_board_init(void)
+{
+ enable_tzc380();
+
+ /* Adjust pmic voltage to 1.0V for 800M */
+ setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
+
+ power_init_board();
+
+ /* DDR initialization */
+ spl_dram_init();
+
+ /* Serial download mode */
+ if (is_usb_boot()) {
+ puts("Back to ROM, SDP\n");
+ restore_boot_params();
+ }
+ puts("Normal Boot\n");
+}
+
+#ifdef CONFIG_SPL_LOAD_FIT
+int board_fit_config_name_match(const char *name)
+{
+ /* Just empty function now - can't decide what to choose */
+ debug("%s: %s\n", __func__, name);
+
+ return 0;
+}
+#endif
+
+void board_init_f(ulong dummy)
+{
+ /* Clear global data */
+ memset((void *)gd, 0, sizeof(gd_t));
+
+ arch_cpu_init();
+
+ init_uart_clk(0);
+
+ board_early_init_f();
+
+ timer_init();
+
+ preloader_console_init();
+
+ /* Clear the BSS. */
+ memset(__bss_start, 0, __bss_end - __bss_start);
+
+ board_init_r(NULL, 0);
+}
diff --git a/configs/mx8mq_evk_defconfig b/configs/mx8mq_evk_defconfig
new file mode 100644
index 0000000000..cee339d496
--- /dev/null
+++ b/configs/mx8mq_evk_defconfig
@@ -0,0 +1,28 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX8M=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_TARGET_MX8MQ_EVK=y
+CONFIG_DEFAULT_DEVICE_TREE="fsl-imx8mq-evk"
+CONFIG_FIT=y
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
+CONFIG_SPL=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_OF_CONTROL=y
+CONFIG_DM_GPIO=y
+CONFIG_DM_I2C=y
+CONFIG_DM_MMC=y
+CONFIG_DM_ETH=y
+CONFIG_PINCTRL=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_PMIC_PFUZE100=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_PFUZE100=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_DM_THERMAL=y
+CONFIG_FS_FAT=y
diff --git a/include/configs/mx8mq_evk.h b/include/configs/mx8mq_evk.h
new file mode 100644
index 0000000000..0a70733560
--- /dev/null
+++ b/include/configs/mx8mq_evk.h
@@ -0,0 +1,265 @@
+/*
+ * Copyright 2017 NXP
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __IMX8M_EVK_H
+#define __IMX8M_EVK_H
+
+#include <linux/sizes.h>
+#include <asm/arch/imx-regs.h>
+
+#ifdef CONFIG_SECURE_BOOT
+#define CONFIG_CSF_SIZE 0x2000 /* 8K region */
+#endif
+
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_TEXT_BASE 0x7E1000
+#define CONFIG_SPL_MAX_SIZE (124 * 1024)
+#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300
+#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
+
+#ifdef CONFIG_SPL_BUILD
+/*#define CONFIG_ENABLE_DDR_TRAINING_DEBUG*/
+#define CONFIG_SPL_WATCHDOG_SUPPORT
+#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
+#define CONFIG_SPL_POWER_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_BOARD_INIT
+#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
+#define CONFIG_SPL_STACK 0x187FF0
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_GPIO_SUPPORT
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_BSS_START_ADDR 0x00180000
+#define CONFIG_SPL_BSS_MAX_SIZE 0x2000 /* 8 KB */
+#define CONFIG_SYS_SPL_MALLOC_START 0x00182000
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x2000 /* 8 KB */
+#define CONFIG_SYS_ICACHE_OFF
+#define CONFIG_SYS_DCACHE_OFF
+
+#define CONFIG_SPL_ABORT_ON_RAW_IMAGE
+
+#undef CONFIG_DM_MMC
+#undef CONFIG_DM_PMIC
+#undef CONFIG_DM_PMIC_PFUZE100
+
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
+#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
+#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
+
+#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+
+#define CONFIG_POWER
+#define CONFIG_POWER_I2C
+#define CONFIG_POWER_PFUZE100
+#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
+#endif
+
+#define CONFIG_REMAKE_ELF
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_LATE_INIT
+
+#undef CONFIG_CMD_EXPORTENV
+#undef CONFIG_CMD_IMPORTENV
+#undef CONFIG_CMD_IMLS
+
+#undef CONFIG_CMD_CRC32
+#undef CONFIG_BOOTM_NETBSD
+
+/* ENET Config */
+/* ENET1 */
+#if defined(CONFIG_CMD_NET)
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MII
+#define CONFIG_MII
+#define CONFIG_ETHPRIME "FEC"
+
+#define CONFIG_FEC_MXC
+#define CONFIG_FEC_XCV_TYPE RGMII
+#define CONFIG_FEC_MXC_PHYADDR 0
+#define FEC_QUIRK_ENET_MAC
+
+#define CONFIG_PHY_GIGE
+#define IMX_FEC_BASE 0x30BE0000
+
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_ATHEROS
+#endif
+
+#define CONFIG_MFG_ENV_SETTINGS \
+ "mfgtool_args=setenv bootargs console=${console},${baudrate} " \
+ "rdinit=/linuxrc " \
+ "g_mass_storage.stall=0 g_mass_storage.removable=1 " \
+ "g_mass_storage.idVendor=0x066F g_mass_storage.idProduct=0x37FF "\
+ "g_mass_storage.iSerialNumber=\"\" "\
+ "clk_ignore_unused "\
+ "\0" \
+ "initrd_addr=0x43800000\0" \
+ "initrd_high=0xffffffff\0" \
+ "bootcmd_mfg=run mfgtool_args;booti ${loadaddr} ${initrd_addr} ${fdt_addr};\0" \
+/* Initial environment variables */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_MFG_ENV_SETTINGS \
+ "script=boot.scr\0" \
+ "image=Image\0" \
+ "console=ttymxc0,115200 earlycon=ec_imx6q,0x30860000,115200\0" \
+ "fdt_addr=0x43000000\0" \
+ "fdt_high=0xffffffffffffffff\0" \
+ "boot_fdt=try\0" \
+ "fdt_file=fsl-imx8mq-evk.dtb\0" \
+ "initrd_addr=0x43800000\0" \
+ "initrd_high=0xffffffffffffffff\0" \
+ "mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
+ "mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
+ "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
+ "mmcautodetect=yes\0" \
+ "mmcargs=setenv bootargs console=${console} root=${mmcroot}\0 " \
+ "loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+ "bootscript=echo Running bootscript from mmc ...; " \
+ "source\0" \
+ "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
+ "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "run mmcargs; " \
+ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+ "if run loadfdt; then " \
+ "booti ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi; " \
+ "else " \
+ "echo wait for boot; " \
+ "fi;\0" \
+ "netargs=setenv bootargs console=${console} " \
+ "root=/dev/nfs " \
+ "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+ "netboot=echo Booting from net ...; " \
+ "run netargs; " \
+ "if test ${ip_dyn} = yes; then " \
+ "setenv get_cmd dhcp; " \
+ "else " \
+ "setenv get_cmd tftp; " \
+ "fi; " \
+ "${get_cmd} ${loadaddr} ${image}; " \
+ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+ "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+ "booti ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi; " \
+ "else " \
+ "booti; " \
+ "fi;\0"
+
+#define CONFIG_BOOTCOMMAND \
+ "mmc dev ${mmcdev}; if mmc rescan; then " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
+ "else " \
+ "if run loadimage; then " \
+ "run mmcboot; " \
+ "else run netboot; " \
+ "fi; " \
+ "fi; " \
+ "else booti ${loadaddr} - ${fdt_addr}; fi"
+
+/* Link Definitions */
+#define CONFIG_LOADADDR 0x40480000
+#define CONFIG_SYS_TEXT_BASE 0x40200000
+
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+
+#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
+#define CONFIG_SYS_INIT_RAM_SIZE 0x80000
+#define CONFIG_SYS_INIT_SP_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_ENV_OFFSET (64 * SZ_64K)
+#define CONFIG_ENV_SIZE 0x1000
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 1 /* USDHC2 */
+#define CONFIG_MMCROOT "/dev/mmcblk1p2" /* USDHC2 */
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN ((CONFIG_ENV_SIZE + (2 * 1024)) * 1024)
+
+#define CONFIG_SYS_SDRAM_BASE 0x40000000
+#define PHYS_SDRAM 0x40000000
+#define PHYS_SDRAM_SIZE 0xC0000000 /* 3GB DDR */
+#define CONFIG_NR_DRAM_BANKS 1
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE UART1_BASE_ADDR
+
+/* Monitor Command Prompt */
+#undef CONFIG_SYS_PROMPT
+#define CONFIG_SYS_PROMPT "u-boot=> "
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_CBSIZE 1024
+#define CONFIG_SYS_MAXARGS 64
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_CMDLINE_EDITING
+
+#define CONFIG_IMX_BOOTAUX
+
+#define CONFIG_CMD_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_FSL_USDHC
+
+#define CONFIG_SYS_FSL_USDHC_NUM 2
+#define CONFIG_SYS_FSL_ESDHC_ADDR 0
+
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_EXT4
+#define CONFIG_CMD_EXT4_WRITE
+#define CONFIG_CMD_FAT
+
+#define CONFIG_SUPPORT_EMMC_BOOT /* eMMC specific */
+#define CONFIG_SYS_MMC_IMG_LOAD_PART 1
+
+#define CONFIG_FSL_QSPI /* enable the QUADSPI driver */
+#ifdef CONFIG_FSL_QSPI
+#define CONFIG_CMD_SF
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_SPI_FLASH_BAR
+#define CONFIG_SF_DEFAULT_BUS 0
+#define CONFIG_SF_DEFAULT_CS 0
+#define CONFIG_SF_DEFAULT_SPEED 40000000
+#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
+
+#define FSL_QSPI_FLASH_SIZE (SZ_32M)
+#define FSL_QSPI_FLASH_NUM 1
+#endif
+
+#define CONFIG_MXC_GPIO
+
+#define CONFIG_MXC_OCOTP
+#define CONFIG_CMD_FUSE
+
+/* I2C Configs */
+#define CONFIG_SYS_I2C_SPEED 100000
+
+#define CONFIG_OF_SYSTEM_SETUP
+
+#endif
--
2.14.1
More information about the U-Boot
mailing list