[U-Boot] [RFC PATCH v3 06/10] nand: pxa3xx: Increase READ_ID buffer and make the size static

[oferh at marvell.com]

From: Ofer Heifetz <oferh at marvell.com>

The read ID count should be made as large as the maximum READ_ID size,
so there's no need to have dynamic size. This commit sets the hardware
maximum read ID count, which should be more than enough on all cases.
Also, we get rid of the read_id_bytes, and use a macro instead.

[ Linux commit b226eca2088004622434cbcc27c6401b64f22d7c]

Cc: Ezequiel García <ezequiel at vanguardiasur.com.ar>
Signed-off-by: Chris Packham <judge.packham at gmail.com>
Reviewed-by: Ofer Heifetz <oferh at marvell.com>
Tested-by: Ofer Heifetz <oferh at marvell.com>
---
 drivers/mtd/nand/pxa3xx_nand.c | 29 ++++++++++-------------------
 1 file changed, 10 insertions(+), 19 deletions(-)

diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index d83efea..86e6c41 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -113,6 +113,13 @@ DECLARE_GLOBAL_DATA_PTR;
 #define EXT_CMD_TYPE_LAST_RW	1 /* Last naked read/write */
 #define EXT_CMD_TYPE_MONO	0 /* Monolithic read/write */
 
+/*
+ * This should be large enough to read 'ONFI' and 'JEDEC'.
+ * Let's use 7 bytes, which is the maximum ID count supported
+ * by the controller (see NDCR_RD_ID_CNT_MASK).
+ */
+#define READ_ID_BYTES		7
+
 /* macros for registers read/write */
 #define nand_writel(info, off, val)	\
 	writel((val), (info)->mmio_base + (off))
@@ -159,8 +166,6 @@ struct pxa3xx_nand_host {
 	/* calculated from pxa3xx_nand_flash data */
 	unsigned int		col_addr_cycles;
 	unsigned int		row_addr_cycles;
-	size_t			read_id_bytes;
-
 };
 
 struct pxa3xx_nand_info {
@@ -861,7 +866,7 @@ static int prepare_set_command(struct pxa3xx_nand_info *info, int command,
 		break;
 
 	case NAND_CMD_READID:
-		info->buf_count = host->read_id_bytes;
+		info->buf_count = READ_ID_BYTES;
 		info->ndcb0 |= NDCB0_CMD_TYPE(3)
 				| NDCB0_ADDR_CYC(1)
 				| command;
@@ -1241,23 +1246,10 @@ static int pxa3xx_nand_config_flash(struct pxa3xx_nand_info *info)
 
 static int pxa3xx_nand_detect_config(struct pxa3xx_nand_info *info)
 {
-	/*
-	 * We set 0 by hard coding here, for we don't support keep_config
-	 * when there is more than one chip attached to the controller
-	 */
-	struct pxa3xx_nand_host *host = info->host[0];
 	uint32_t ndcr = nand_readl(info, NDCR);
 
-	if (ndcr & NDCR_PAGE_SZ) {
-		/* Controller's FIFO size */
-		info->chunk_size = 2048;
-		host->read_id_bytes = 4;
-	} else {
-		info->chunk_size = 512;
-		host->read_id_bytes = 2;
-	}
-
 	/* Set an initial chunk size */
+	info->chunk_size = ndcr & NDCR_PAGE_SZ ? 2048 : 512;
 	info->reg_ndcr = ndcr & ~NDCR_INT_MASK;
 	info->ndtr0cs0 = nand_readl(info, NDTR0CS0);
 	info->ndtr1cs0 = nand_readl(info, NDTR1CS0);
@@ -1287,7 +1279,7 @@ static int pxa3xx_nand_sensing(struct pxa3xx_nand_host *host)
 	/* configure default flash values */
 	info->reg_ndcr = 0x0; /* enable all interrupts */
 	info->reg_ndcr |= (pdata->enable_arbiter) ? NDCR_ND_ARB_EN : 0;
-	info->reg_ndcr |= NDCR_RD_ID_CNT(host->read_id_bytes);
+	info->reg_ndcr |= NDCR_RD_ID_CNT(READ_ID_BYTES);
 	info->reg_ndcr |= NDCR_SPARE_EN; /* enable spare by default */
 
 	/* use the common timing to make a try */
@@ -1504,7 +1496,6 @@ static int alloc_nand_resource(struct pxa3xx_nand_info *info)
 		info->host[cs] = host;
 		host->cs = cs;
 		host->info_data = info;
-		host->read_id_bytes = 4;
 		mtd->owner = THIS_MODULE;
 
 		nand_set_controller_data(chip, host);
-- 
1.9.1