[U-Boot] [PATCH 09/13] board: ti: am574x-idk: Add ddr data support

[Lukasz Majewski]

Hi Lokesh,

> AM574x-idk has the following DDR parts attached:
> EMIF1: MT41K256M16HA (1GB with ECC)
> EMIF2: MT41K256M16HA (1GB without ECC)
> 
> Enabling 2GB DDR without interleaving between EMIFs. And
> enabling ECC on EMIF1.
> 
> Signed-off-by: Lokesh Vutla <lokeshvutla at ti.com>
> Signed-off-by: Krunal Bhargav <k-bhargav at ti.com>
> ---
>  board/ti/am57xx/board.c | 47
> ++++++++++++++++++++++++++++++++++++++++++++--- 1 file changed, 44
> insertions(+), 3 deletions(-)
> 
> diff --git a/board/ti/am57xx/board.c b/board/ti/am57xx/board.c
> index 2d14ae54fe..1377c7b1fe 100644
> --- a/board/ti/am57xx/board.c
> +++ b/board/ti/am57xx/board.c
> @@ -89,10 +89,18 @@ static const struct dmm_lisa_map_regs
> am571x_idk_lisa_regs = { .is_ma_present  = 0x1
>  };
>  
> +static const struct dmm_lisa_map_regs am574x_idk_lisa_regs = {
> +	.dmm_lisa_map_2 = 0xc0600200,
> +	.dmm_lisa_map_3 = 0x80600100,
> +	.is_ma_present  = 0x1
> +};
> +
>  void emif_get_dmm_regs(const struct dmm_lisa_map_regs
> **dmm_lisa_regs) {
>  	if (board_is_am571x_idk())
>  		*dmm_lisa_regs = &am571x_idk_lisa_regs;
> +	else if (board_is_am574x_idk())
> +		*dmm_lisa_regs = &am574x_idk_lisa_regs;
>  	else
>  		*dmm_lisa_regs = &beagle_x15_lisa_regs;
>  }
> @@ -231,8 +239,8 @@ static const struct emif_regs
> am571x_emif1_ddr3_666mhz_emif_regs =
> { .ref_ctrl			=
> 0x0000514d, .ref_ctrl_final			=
> 0x0000144a, .sdram_tim1			= 0xd333887c,
> -	.sdram_tim2			= 0x40b37fe3,
> -	.sdram_tim3			= 0x409f8ada,
> +	.sdram_tim2			= 0x30b37fe3,
> +	.sdram_tim3			= 0x409f8ad8,
>  	.read_idle_ctrl			= 0x00050000,
>  	.zq_config			= 0x5007190b,
>  	.temp_alert_config		= 0x00000000,
> @@ -249,17 +257,50 @@ static const struct emif_regs
> am571x_emif1_ddr3_666mhz_emif_regs =
> { .emif_rd_wr_exec_thresh		= 0x00000305 };
>  
> +static const struct emif_regs am574x_emif1_ddr3_666mhz_emif_ecc_regs
> = {
> +	.sdram_config_init		= 0x61863332,
> +	.sdram_config			= 0x61863332,
> +	.sdram_config2			= 0x08000000,
> +	.ref_ctrl			= 0x0000514d,
> +	.ref_ctrl_final			= 0x0000144a,
> +	.sdram_tim1			= 0xd333887c,
> +	.sdram_tim2			= 0x30b37fe3,
> +	.sdram_tim3			= 0x409f8ad8,
> +	.read_idle_ctrl			= 0x00050000,
> +	.zq_config			= 0x5007190b,
> +	.temp_alert_config		= 0x00000000,
> +	.emif_ddr_phy_ctlr_1_init	= 0x0024400f,
> +	.emif_ddr_phy_ctlr_1		= 0x0e24400f,
> +	.emif_ddr_ext_phy_ctrl_1	= 0x10040100,
> +	.emif_ddr_ext_phy_ctrl_2	= 0x00910091,
> +	.emif_ddr_ext_phy_ctrl_3	= 0x00950095,
> +	.emif_ddr_ext_phy_ctrl_4	= 0x009b009b,
> +	.emif_ddr_ext_phy_ctrl_5	= 0x009e009e,
> +	.emif_rd_wr_lvl_rmp_win		= 0x00000000,
> +	.emif_rd_wr_lvl_rmp_ctl		= 0x80000000,
> +	.emif_rd_wr_lvl_ctl		= 0x00000000,
> +	.emif_rd_wr_exec_thresh		= 0x00000305,
> +	.emif_ecc_ctrl_reg		= 0xD0000001,
> +	.emif_ecc_address_range_1	= 0x3FFF0000,
> +	.emif_ecc_address_range_2	= 0x00000000
> +};

I'm wondering if it would be possible to:

Embed this memory setup (even as binary blob) to SPL FIT -> Those
values are generated from TI supplied excel sheet (when memory details
are provided).


Pros:
----

- Since the same EMIF controller is used, one could only adjust the
  binary blob, when new memory (faster, slower, from other manufacturer)
  is used in the product.

- There would be no need to add such code to the board file.

> +
>  void emif_get_reg_dump(u32 emif_nr, const struct emif_regs **regs)
>  {
>  	switch (emif_nr) {
>  	case 1:
>  		if (board_is_am571x_idk())
>  			*regs = &am571x_emif1_ddr3_666mhz_emif_regs;
> +		else if (board_is_am574x_idk())
> +			*regs =
> &am574x_emif1_ddr3_666mhz_emif_ecc_regs; else
>  			*regs =
> &beagle_x15_emif1_ddr3_532mhz_emif_regs; break;
>  	case 2:
> -		*regs = &beagle_x15_emif2_ddr3_532mhz_emif_regs;
> +		if (board_is_am574x_idk())
> +			*regs = &am571x_emif1_ddr3_666mhz_emif_regs;
> +		else
> +			*regs =
> &beagle_x15_emif2_ddr3_532mhz_emif_regs; break;
>  	}
>  }



Best regards,

Lukasz Majewski

--

DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 488 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20171218/1046041a/attachment.sig>