[U-Boot] [PATCH v1 03/10] mmc: remove unneeded verification in mmc_set_card_speed()

[Jaehoon Chung]

On 12/21/2017 08:53 PM, Jean-Jacques Hiblot wrote:
> mmc_set_card_speed() reads the ext csd to check if switch has been OK.
> But it does it only for MMC_HS and MMC_HS_52. Moreover this check is not
> really required as there will be a ext csd reading later in the
> initialization process to make sure that it succeeded.
> So remove this partial verification and save space.

Yes, it's saved the space, but it may be affected with the driver strength value.
It needs to consider more whether we can remove it.

> 
> Signed-off-by: Jean-Jacques Hiblot <jjhiblot at ti.com>
> ---
> 
>  drivers/mmc/mmc.c | 22 +++-------------------
>  1 file changed, 3 insertions(+), 19 deletions(-)
> 
> diff --git a/drivers/mmc/mmc.c b/drivers/mmc/mmc.c
> index 67d05c5..7a92718 100644
> --- a/drivers/mmc/mmc.c
> +++ b/drivers/mmc/mmc.c
> @@ -788,11 +788,8 @@ int mmc_switch(struct mmc *mmc, u8 set, u8 index, u8 value)
>  
>  static int mmc_set_card_speed(struct mmc *mmc, enum bus_mode mode)
>  {
> -	int err;
>  	int speed_bits;
>  
> -	ALLOC_CACHE_ALIGN_BUFFER(u8, test_csd, MMC_MAX_BLOCK_LEN);
> -
>  	switch (mode) {
>  	case MMC_HS:
>  	case MMC_HS_52:
> @@ -808,23 +805,8 @@ static int mmc_set_card_speed(struct mmc *mmc, enum bus_mode mode)
>  	default:
>  		return -EINVAL;
>  	}
> -	err = mmc_switch(mmc, EXT_CSD_CMD_SET_NORMAL, EXT_CSD_HS_TIMING,
> +	return mmc_switch(mmc, EXT_CSD_CMD_SET_NORMAL, EXT_CSD_HS_TIMING,
>  			 speed_bits);
> -	if (err)
> -		return err;
> -
> -	if ((mode == MMC_HS) || (mode == MMC_HS_52)) {
> -		/* Now check to see that it worked */
> -		err = mmc_send_ext_csd(mmc, test_csd);
> -		if (err)
> -			return err;
> -
> -		/* No high-speed support */
> -		if (!test_csd[EXT_CSD_HS_TIMING])
> -			return -ENOTSUPP;
> -	}
> -
> -	return 0;
>  }
>  
>  static int mmc_get_capabilities(struct mmc *mmc)
> @@ -851,10 +833,12 @@ static int mmc_get_capabilities(struct mmc *mmc)
>  	cardtype = ext_csd[EXT_CSD_CARD_TYPE] & 0x3f;
>  	mmc->cardtype = cardtype;
>  
> +#if CONFIG_IS_ENABLED(MMC_HS200_SUPPORT)
>  	if (cardtype & (EXT_CSD_CARD_TYPE_HS200_1_2V |
>  			EXT_CSD_CARD_TYPE_HS200_1_8V)) {
>  		mmc->card_caps |= MMC_MODE_HS200;
>  	}
> +#endif

It's not related with your subject.?


Best Regards,
Jaehoon Chung

>  	if (cardtype & EXT_CSD_CARD_TYPE_52) {
>  		if (cardtype & EXT_CSD_CARD_TYPE_DDR_52)
>  			mmc->card_caps |= MMC_MODE_DDR_52MHz;
>