[U-Boot] [RESEND PATCH v2] ARM: at91: add default config file for sama5d36ek CMP board

[Wenyou Yang]

The sama5d36ek CMP board is the variant of sama5d3xek board.
It is equipped with the low-power DDR2 SDRAM, PMIC ACT8865, and
some power rail. Its main purpose is used to measure the power
consumption. As those changes are done in at91bootstrap,
in U-Boot, use another device tree file, no code to change.

As there is additional power consumption due to the USB Host
and USB Device enabled, for the power consumption measurement,
disable the USB host and device.

Signed-off-by: Wenyou Yang <wenyou.yang at atmel.com>
---

Changes in v2:
 - rebase on the patch set:
        [PATCH v2 0/7] board: sama5d3: convert boards to support DM/DT
        http://lists.denx.de/pipermail/u-boot/2017-February/280515.html

 configs/sama5d36ek_cmp_mmc_defconfig       | 58 ++++++++++++++++++++++++++++++
 configs/sama5d36ek_cmp_nandflash_defconfig | 57 +++++++++++++++++++++++++++++
 configs/sama5d36ek_cmp_spiflash_defconfig  | 57 +++++++++++++++++++++++++++++
 3 files changed, 172 insertions(+)
 create mode 100644 configs/sama5d36ek_cmp_mmc_defconfig
 create mode 100644 configs/sama5d36ek_cmp_nandflash_defconfig
 create mode 100644 configs/sama5d36ek_cmp_spiflash_defconfig

diff --git a/configs/sama5d36ek_cmp_mmc_defconfig b/configs/sama5d36ek_cmp_mmc_defconfig
new file mode 100644
index 0000000000..ee72c59afe
--- /dev/null
+++ b/configs/sama5d36ek_cmp_mmc_defconfig
@@ -0,0 +1,58 @@
+CONFIG_ARM=y
+CONFIG_ARCH_AT91=y
+CONFIG_TARGET_SAMA5D3XEK=y
+CONFIG_SPL_GPIO_SUPPORT=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_SPL_FAT_SUPPORT=y
+CONFIG_SPL_LIBDISK_SUPPORT=y
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_DEFAULT_DEVICE_TREE="sama5d36ek_cmp"
+CONFIG_FIT=y
+CONFIG_SYS_EXTRA_OPTIONS="SAMA5D3,SYS_USE_MMC"
+CONFIG_BOOTDELAY=3
+# CONFIG_CONSOLE_MUX is not set
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_SPL=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_SPL_DM=y
+CONFIG_CLK=y
+CONFIG_SPL_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_AT91_UTMI=y
+CONFIG_AT91_H32MX=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_GENERIC_ATMEL_MCI=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_ATMEL=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xffffee00
+CONFIG_DEBUG_UART_CLOCK=0
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
+CONFIG_DM_SPI=y
+CONFIG_ATMEL_SPI=y
+CONFIG_LCD=y
diff --git a/configs/sama5d36ek_cmp_nandflash_defconfig b/configs/sama5d36ek_cmp_nandflash_defconfig
new file mode 100644
index 0000000000..aabbf4a4da
--- /dev/null
+++ b/configs/sama5d36ek_cmp_nandflash_defconfig
@@ -0,0 +1,57 @@
+CONFIG_ARM=y
+CONFIG_ARCH_AT91=y
+CONFIG_TARGET_SAMA5D3XEK=y
+CONFIG_SPL_GPIO_SUPPORT=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_SPL_NAND_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_DEFAULT_DEVICE_TREE="sama5d36ek_cmp"
+CONFIG_FIT=y
+CONFIG_SYS_EXTRA_OPTIONS="SAMA5D3,SYS_USE_NANDFLASH"
+CONFIG_BOOTDELAY=3
+# CONFIG_CONSOLE_MUX is not set
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_SPL=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clocks clock-names interrupt-parent"
+CONFIG_DM=y
+CONFIG_SPL_DM=y
+CONFIG_CLK=y
+CONFIG_SPL_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_AT91_UTMI=y
+CONFIG_AT91_H32MX=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_GENERIC_ATMEL_MCI=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_ATMEL=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xffffee00
+CONFIG_DEBUG_UART_CLOCK=0
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
+CONFIG_DM_SPI=y
+CONFIG_ATMEL_SPI=y
+CONFIG_LCD=y
diff --git a/configs/sama5d36ek_cmp_spiflash_defconfig b/configs/sama5d36ek_cmp_spiflash_defconfig
new file mode 100644
index 0000000000..e4131d9d2a
--- /dev/null
+++ b/configs/sama5d36ek_cmp_spiflash_defconfig
@@ -0,0 +1,57 @@
+CONFIG_ARM=y
+CONFIG_ARCH_AT91=y
+CONFIG_TARGET_SAMA5D3XEK=y
+CONFIG_SPL_GPIO_SUPPORT=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL_SPI_FLASH_SUPPORT=y
+CONFIG_SPL_SPI_SUPPORT=y
+CONFIG_DEFAULT_DEVICE_TREE="sama5d36ek_cmp"
+CONFIG_FIT=y
+CONFIG_SYS_EXTRA_OPTIONS="SAMA5D3,SYS_USE_SERIALFLASH"
+CONFIG_BOOTDELAY=3
+# CONFIG_CONSOLE_MUX is not set
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_SPL=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_DM=y
+CONFIG_SPL_DM=y
+CONFIG_CLK=y
+CONFIG_SPL_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_AT91_UTMI=y
+CONFIG_AT91_H32MX=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_GENERIC_ATMEL_MCI=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_ATMEL=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_BASE=0xffffee00
+CONFIG_DEBUG_UART_CLOCK=0
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
+CONFIG_DM_SPI=y
+CONFIG_ATMEL_SPI=y
+CONFIG_LCD=y
-- 
2.11.0